Various settings
34
∫ 3. Hardware
Speaker Impedance:
If any of the connected speakers
have 4
h
or more to less than 6
h
impedance, or if you
have connected a different set of left and right speakers
to the SPEAKERS A/B terminals, set the impedance to
4
h
.
0
Reduce the volume to minimum before setting.
6h
(default setting)
4h
AutoPowerDown:
The unit will automatically enter
standby mode (*) if there is no operation for 20 minutes
with no audio signal input.
On
(default setting)
Off
*
Becomes the NETWORK STANDBY mode, which keeps the
increase in power consumption to a minimum, when any of
Network Standby, Bluetooth Wakeup, or Opt1 In Wakeup are
on.
Network Standby:
You can turn on the power of the unit
via network using an application such as SX-N30
ControlApp.
On
Off
(default setting)
0
When “Network Standby” is used, the power
consumption increases even when the unit is on
standby. However, the increase in power consumption
is kept to a minimum by automatically entering the
NETWORK STANDBY mode, where only the essential
circuit is operating.
0
If it is not displayed, wait for a moment until the
network feature starts.
Bluetooth Wakeup:
This function wakes up the unit on
standby by connecting a
Bluetooth
enabled device.
On
Off
(default setting)
0
Setting to “On” increases the power consumption even
when the unit is on standby. However, the increase in
power consumption is kept to a minimum by
automatically entering the NETWORK STANDBY
mode, where only the essential circuit is operating.
0
This setting is fixed to “Off” if “6. Bluetooth”-“Auto In
Change” (
>
35) is set to “Off”.
0
If it is not displayed, wait for a moment until the
network feature starts.
Opt1 In Wakeup:
When an audio signal is input through
the OPTICAL terminal while this unit is in standby, this
feature automatically detects it.
Off
(default setting)
On
: This unit is turned on and outputs the audio.
0
When a cable is connected to the OPTICAL terminal
and this setting is enabled, power consumption
increases even when the unit is on standby, however,
the increase in power consumption is kept to a
minimum by automatically entering the NETWORK
STANDBY mode, where only essential circuits are
operating.
AM Freq Step
(SX-N30)
:
Changes the AM radio
frequency step.
9kHz
(default setting): The frequency is adjusted in
increments of 9 kHz.
10kHz
: The frequency is adjusted in increments of
10 kHz.
DAB Scan
(SX-N30DAB)
:
This setting determines which
DAB bands are scanned by the Auto Tuning function. To
start scanning, select the item and press the ENTER
button.
World Wide
(default setting): Band
III
(5A - 13F)
UK
: Band
III
(11B - 12D)
DAB DRC
(SX-N30DAB)
:
With the DRC (Dynamic
Range Control) setting, you can reduce the dynamic
range of DAB digital radio so that you can still hear quiet
parts even when listening at low volume levels - ideal for
listening to the radio late at night when you don’t want to
disturb anyone.
0
(default setting): DRC off
1
: Large reduction in dynamic range
1/2
: Small reduction in dynamic range
FM Search Lvl
(SX-N30DAB)
:
You can choose to have
only those FM stations with strong reception selected
when tuning into stations automatically if tuning regularly
stops on FM stations with weak reception. Select “FM” as
the input source to make this setting.
Normal
(default setting)
Strong
: Select only stations with strong reception.
∫ 4. Source
IntelliVolume:
Even when the volume control is the same
on this unit, there may be differences in the volume
depending on the connected devices. Adjust this when
you want to alleviate this difference. To set, select each
input source.
j12 dB
to
i12 dB
(default setting: 0 dB)
Name Edit:
Enter a simple name of up to 10 characters
in length for the input sources or preset AM/DAB/FM
stations. To set, select each input source or select the
preset number of the registered station.
0
For information on how to input characters, see
“Inputting characters” (
>
33).
∫ 5. Network
Make the network setting.
0
If it is not displayed, wait for a moment until the
network feature starts.
0
When LAN is configured with a DHCP, set “DHCP” to
“Enable” to configure the setting automatically.
(“Enable” is set by default) To assign fixed IP
addresses to each components, you must set “DHCP”
to “Disable” and assign an address to this unit in “IP
Address” as well as set information related to your
LAN, such as Subnet Mask and Gateway.
Wi-Fi:
Connect the unit to network via wireless LAN
router.
On
: Wireless LAN connection
Off (Wired)
(default setting): Wired LAN connection
Wi-Fi Setup:
You can configure wireless LAN settings by
pressing the ENTER button when “Start” is displayed. For
details, see “Wi-Fi
®
connection” (
>
15).
SSID:
The SSID of the connected access point will be
displayed.
SX-N30_mst.book 34 ページ ２０１５年１１月２日 月曜日 午後１２時５５分
