580827
115
Verklein
Vergroot
Pagina terug
1/141
Pagina verder
115
FAQ
13
Symptom Remedy
No sound from front height or front
wide speakers.
Check that the front height or front wide speakers are set to LARGE or SMALL, and the
surround speakers are not set to NO (see Speaker Setting on page 104 ).
When Speaker System is set to 7.2.2ch TMd/FW and SP: TMd ON is selected with the
OUT P. button, no sound will be output from the front wide speakers. Select SP: FW ON
or SP: TMd/FW ON (see Switching the speaker terminals on page 83 ).
When Speaker System is set to 7.2.2ch TMd/FH and SP: TMd ON is selected with the
OUT P. button, no sound will be output from the front height speakers. Select SP: FH ON
or SP: TMd/FH ON (see Switching the speaker terminals on page 83 ).
Check the speaker connections (see Connecting the speakers on page 24 ).
When Speaker System is set to 7.2.2ch TMd/FW and Dolby Surround is selected,
audio is not output from the front wide speakers.
No sound from subwoofer. Check that the subwoofer is connected properly, switched on and the volume turned up.
If your subwoofer has a sleep function, make sure it is switched off.
Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 104 ).
The crossover frequency may be set too low; try setting it higher to match the characteris-
tics of your other speakers (see Speaker Setting on page 104 ).
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting on page 104 ).
Check that the LFE channel is not set to OFF, or to a very quiet setting (see Setting the
Audio options on page 79 ).
Check the speaker level settings (see Channel Level on page 105 ).
No sound from the speakers.
Check the AMP setting. Set it to ON when you want to output sound from all the speakers
(Setting the Audio options on page 79 ).
No sound from one speaker.
Check the speaker connection (see Connecting the speakers on page 24 ).
Check the speaker level settings (see Channel Level on page 105 ).
Check that the speaker hasn’t been set to NO (see Speaker Setting on page 104 ).
The channel may not be recorded in the source. By using one of the advanced effect
listening modes, you may be able to create the missing channel (see Enjoying various
types of playback using the listening modes on page 64 ).
Sound is produced from analog
components, but not from digital
ones (DVD, LD, CD, etc.).
Check that the input signal type is set to DIGITAL (see Choosing the input signal on page 66 ).
Make sure that the digital input is assigned correctly for the input jack the component is
connected to (see The Input Setup menu on page 51 ).
Check the digital output settings on the source component.
If the source component has a digital volume control, make sure this is not turned down.
SC-LX88 only:
No sound is produced even if
MULTI CH IN is selected.
When 5.2ch F+Surr Bi-Amp, 5.2ch F+C Bi-Amp or 5.2ch C+Surr Bi-Amp is selected in
the Speaker System settings (when the center or surround speakers are bi-amped), no
sound is produced even when MULTI CH IN is selected.
No sound is output or a noise is out-
put when Dolby Digital/DTS software
is played back.
Check that your BD or DVD player is compatible with Dolby Digital/DTS discs.
Check the digital output settings or the HDMI audio output settings of your BD or DVD
player. Make sure that the DTS signal output is set to On.
If the source component has a digital volume control, make sure this is not turned down.
No sound when using the
HOME MENU.
If the HDMI input function is selected, sound is muted until exiting the HOME MENU.
Other audio problems
Symptom Remedy
Speaker switching sound (clicking
sound) is heard from receiver during
playback.
Since ECO MODE 1 and ECO MODE 2 reduce the power consumption, the speakers
are switched in function of the number of input channels. Because of this, a speaker
switching sound (clicking sound) may be produced when the number of input channels
is switched. If this bothers you, switch to a different listening mode.
Depending on the listening mode, the front height (or front wide) and surround back
speakers may switch automatically in function of changes in the input audio. A speaker
switching sound (clicking sound) will be heard from the receiver at this time. If this sound
bothers you, we recommend to change the speaker terminal option (see Switching the
speaker terminals on page 83 ).
Broadcast stations cannot be
selected automatically, or there is
considerable noise in radio broad-
casts.
Fully extend the FM wire antenna, adjust the position for best reception and secure to a
wall, etc.
Use an outdoor antenna for better reception (see page 40 ).
Adjust the position and direction of the AM antenna.
Noise may be caused by interference from other equipment, such as a fluorescent light,
motor, etc. Switch off or move the other equipment, or move the AM antenna.
Noise is output when scanning a
DTS CD.
This is not a malfunction of the receiver. The scan function of your player alters the digital
information, making it unreadable, resulting in noise being output. Lower the volume
when scanning.
When playing a DTS format LD there
is audible noise on the soundtrack.
Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on
page 66 ).
Can’t record audio. You can only make a digital recording from a digital source, and an analog recording
from an analog source.
For digital sources, make sure that what you’re recording isn’t copy protected.
Subwoofer output is very low.
To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL
(see Speaker Setting on page 104 ).
Everything seems to be set up cor-
rectly, but the playback sound is odd.
The speakers may be out of phase. Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding terminals on the speakers (see Con-
necting the speakers on page 24 ).
The Phase Control feature doesn’t
seem to have an audible effect.
If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass
cutoff is set to the highest frequency setting. If there is a PHASE setting on your sub-
woofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
Make sure the speaker distance setting is correct for all speakers (see Speaker Distance
on page 105 ).
Full Band Phase Control cannot be
selected.
Perform Full Auto MCACC measurements (see Automatically conducting optimum
sound tuning (Full Auto MCACC) on page 49 ). Full Band Phase Control automatically
turns on once measurements are completed.
Noise or hum can be heard even
when there is no sound being input.
Check that personal computers or other digital components connected to the same
power source are not causing interference.
Can’t select some Input functions
by the INPUT SELECTOR on the
front panel or the ALL button on the
remote control.
Check the Input Skip settings in the Input Setup menu (see The Input Setup menu on
page 51 ).
Check the HDMI Input assignment in the Input Setup menu then try OFF (see The Input
Setup menu on page 51 ).
There seems to be a time lag
between the speakers and the output
of the subwoofer.
See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 49
to set up your system again using MCACC (this will automatically compensate for a delay
in the subwoofer output).
 
115

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer SC-LX78-S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer SC-LX78-S in de taal/talen: Engels als bijlage per email.

De handleiding is 17,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Pioneer SC-LX78-S

Pioneer SC-LX78-S Snelstart handleiding - Nederlands - 76 pagina's

Pioneer SC-LX78-S Gebruiksaanwijzing - Nederlands - 146 pagina's

Pioneer SC-LX78-S Snelstart handleiding - Deutsch - 76 pagina's

Pioneer SC-LX78-S Gebruiksaanwijzing - Deutsch - 151 pagina's

Pioneer SC-LX78-S Snelstart handleiding - English, Français - 76 pagina's

Pioneer SC-LX78-S Gebruiksaanwijzing - Français - 145 pagina's

Pioneer SC-LX78-S Snelstart handleiding - Italiano - 76 pagina's

Pioneer SC-LX78-S Gebruiksaanwijzing - Italiano - 144 pagina's

Pioneer SC-LX78-S Snelstart handleiding - Espanõl - 76 pagina's

Pioneer SC-LX78-S Gebruiksaanwijzing - Espanõl - 146 pagina's

Pioneer SC-LX78-S Gebruiksaanwijzing - Dansk, Svenska, Norsk, Suomi - 424 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info