536834
99
Verklein
Vergroot
Pagina terug
1/119
Pagina verder
99
 
 
 
 
13
FAQ
HDMI
Symptom Remedy
The HDMI indicator blinks continu-
ously.
Check all the points below.
No picture or sound. This receiver is HDCP-compatible. Check that the components you are connecting are
also HDCP-compatible. If they are not, please connect them using the component or
composite video jacks.
Depending on the connected source component, it’s possible that it will not work with
this receiver (even if it is HDCP-compatible). In this case, connect using the component
or composite video jacks between source and receiver.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
If video images do not appear on your TV, try adjusting the resolution, Deep Color or other
setting for your component.
While analog video signals are being output over HDMI, use a separate connection for
audio output.
To output signals in Deep Color, use an HDMI cable (High Speed HDMI
®
/
TM
Cable) to
connect this receiver to a component or TV with the Deep Color feature.
Influence from a TV whose power is set to standby may cause the picture or sound not to
be produced or to be broken. In this case, press HDMI OUT and switch so that the HDMI
output to which that TV is connected is not selected.
No picture.
Try changing the Resolution setting (in Setting the Video options on page 67).
To use the HDMI OUT 2 terminal in the main zone, set the MAIN/HDZONE
Output Setting to MAIN (page 91).
No sound, or sound suddenly
ceases.
Check that the HDMI Audio setting is set to AMP (Setting the Audio options on page 65).
If the component is a DVI device, use a separate connection for the audio.
If analog video is being output over HDMI, please use a separate connection for the
audio.
Check the audio output settings of the source component.
HDMI format digital audio transmissions require a longer time to be recognized. Due
to this, interruption in the audio may occur when switching between audio formats or
beginning playback.
Turning on/off the device connected to this unit’s HDMI OUT terminal during playback,
or disconnecting/connecting the HDMI cable during playback, may cause noise or inter-
rupted audio.
Noisy or distorted picture. Sometimes a video deck may output a noisy video signal (during scanning, for example),
or the video quality may just be poor (with some video game units, for example). The
picture quality may also depend on the settings, etc. of your display device. Switch off
the video converter and reconnect the source and display device using the same type of
connection (component or composite), then start playback again.
If the problem still persists when connecting your HDMI component directly to your
monitor, please consult the component or monitor manual or contact the manufacturer
for support.
HDCP ERROR shows in the display. Check whether or not the connected component is compatible with HDCP. If it is not
compatible with HDCP, reconnect the source device using a different type of connection
(component or composite). Some components that are compatible with HDCP still cause
this message to be displayed, but so long as there is no problem with displaying video,
this is not a malfunction.
Symptom Remedy
Synchronized operation not possible
using Control with HDMI function.
Check the HDMI connections.
The cable may be damaged.
Select ON for the Control Mode with HDMI setting (see HDMI Setup on page 61).
Turn the TV’s power on before turning on this receiver’s power.
Set the TV side Control with HDMI setting to on (see TV’s operating instructions).
Connect the TV to the HDMI OUT 1 terminal and set the HDMI output to OUT 1. Then
turn on first the TV’s power, then this receiver’s power.
When HDZONE is set to ON, the
video resolution and number of
audio channels for the main zone
side changes.
This is due to the HDMI connection specifications; it is not a malfunction. When play-
ing the same input in the main zone and HDZONE, video and audio signals that can be
output in common for all the devices connected to the HDMI OUT 1 and HDMI OUT 2
(HDZONE) terminals are set.
HDZONE cannot be turned on.
Set Output Setting at MAIN/HDZONE to HDZONE (page 91).
When the input source for the main
or HDZONE is switched or when
the power of the respective zones is
turned on and off, the audio or video
of the HDMI output terminal that is
not being operated is sometimes
interrupted.
This is because the HDMI devices need to recognize each other again. This is not a
malfunction. If the picture is disturbed or not displayed, turn off the power of the devices
in all the zones, then try again. Also try temporarily turning the Network Standby and
Standby Through settings OFF.
Such menus as the HOME MENU as
well as the on-screen display are not
displayed for HDMI OUT 1.
Press HDMI OUT and switch the HDMI OUT 1/2 setting.
MHL
Symptom Remedy
When playing an MHL-compat-
ible device connected to the
HDMI 5/MHL terminal, the Standby
Through function does not work and
the power turns off.
The MHL device will not operate unless power is being supplied from this receiver. When
this receiver is in the Standby Through mode, power cannot be supplied due to reduced
power consumption. Because of this, the MHL device will not operate. This is not a mal-
function.
AVNavigator
Symptom Causes Remedy
AVNavigator cannot be
installed.
An error message may appear
if there are not enough system
resources available.
Restart the computer and start installing with no other
applications running.
Installation of AVNavigator may fail
because of incompatibilities with
other applications.
Try the following (in given order):
1. If other applications are running on the computer, quit
those applications before installing.
2. If the problem persists, restart the computer and install
with no other applications running.
99

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Pioneer-SC-1223

Zoeken resetten

  • Hallo mijn receiver is via lan aan internet verbonden ,bij internet radio valt steeds mijn zender weg en zie ik op het display genre staan ,ik moet dan opnieuw zender selecteren om weer alles terug te krijgen
    gr rob Gesteld op 24-4-2014 om 09:31

    Reageer op deze vraag Misbruik melden
    • Heb je ooit het probleem gevonden? Ik heb dit ook sinds we jaren terug naar UPC over gingen, via ADSL NOOIT problemen gehad. Geantwoord op 26-10-2014 om 19:14

      Waardeer dit antwoord Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer SC-1223 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer SC-1223 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Pioneer SC-1223

Pioneer SC-1223 Snelstart handleiding - Nederlands - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Nederlands - 120 pagina's

Pioneer SC-1223 Snelstart handleiding - Deutsch - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Deutsch - 122 pagina's

Pioneer SC-1223 Snelstart handleiding - English, Français - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Français - 120 pagina's

Pioneer SC-1223 Snelstart handleiding - Italiano - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Italiano - 120 pagina's

Pioneer SC-1223 Snelstart handleiding - Espanõl - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Espanõl - 120 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Dansk, Svenska - 234 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info