536834
95
Verklein
Vergroot
Pagina terug
1/119
Pagina verder
95
 
 
 
 
13
FAQ
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong
with this component, check the points below. Sometimes the trouble may lie in another component. Investigate
the other components and electrical appliances being used. If the trouble cannot be rectified even after exercis-
ing the checks listed below, ask your nearest Pioneer authorized independent service company to carry out repair
work.
! If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.
If the problem is not solved after the troubleshooting below, if the screen freezes unexpectedly or if the buttons on
the remote control or front panel stop working completely, do the following:
! Press u STANDBY/ON on the front panel to turn off the power, then turn the power back on.
! If the power cannot be turned off, press and hold u STANDBY/ON on the front panel for over 10 seconds. The
power will turn off. In this case, the various settings made on the receiver may be cleared. (However, settings
made when the power was turned off normally are not cleared.)
Power
Symptom Remedy
The power does not turn on. Make sure that the power cord is plugged in to an active power outlet.
Try disconnecting from the power outlet, then plugging back in.
Power cannot be turned off.
(ZONE 2 ON is displayed.)
Press the remote control’s ZONE 2, then press u STANDBY/ON to switch the sub zone
off.
Power cannot be turned off.
(HDZONE ON is displayed.)
Press the remote control’s HDZONE, then press u STANDBY/ON to switch the sub zone
off.
The receiver suddenly switches off
or the iPod iPhone iPad indicator
blinks.
Check that there are no loose strands of speaker wire touching the rear panel or another
set of wires. If so, re-attach the speaker wires, making sure there are no stray strands.
The receiver may have a serious problem. Disconnect from the power and call a Pioneer
authorized independent service company.
During loud playback the power sud-
denly switches off.
Turn down the volume.
Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 80.
Switch on the digital safety feature. While holding down ENTER on the front panel,
press u STANDBY/ON to set this receiver to the standby mode. Use TUNE i/j to
select D.SAFETY cOFFd, and then use PRESET k/l to select 1 or 2 (select D.SAFETY
cOFFd to deactivate this feature). If the power switches off even with 2 switched on, turn
down the volume. With 1 or 2 on, some features may be unavailable.
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting on page 86).
The unit does not respond when the
buttons are pressed.
Try switching the receiver off, then back on again.
Try disconnecting the power cord, then connect again.
AMP ERR blinks in the display, then
the power automatically switches off.
The ADVANCED MCACC blinks and
the power does not turn on.
The receiver may have a serious problem. Do not try switching the receiver on. Unplug the
receiver from the wall and call a Pioneer authorized independent service company.
The receiver suddenly switches off or
the FL OFF indicator blinks.
There is a problem with the receiver’s power unit or fan. Try turning on the power. If the
same thing happens, the receiver is damaged. Unplug the receiver from the wall and call
a Pioneer authorized independent service company. (Other symptoms may appear when
the power is turned on.)
Symptom Remedy
AMP OVERHEAT blinks in the dis-
play and the FL OFF indicator flash
and the power turns off.
Allow the unit to cool down in a well-ventilated place before switching back on (see
Installing the receiver on page 8).
Check whether the cables used to connect the speakers are short-circuited.
Wait at least 1 minute, then try turning the power on again.
The temperature within the unit has exceeded the allowablevalue.
Lower the volume level.
HDZONE cannot be turned on.
Set Output Setting at MAIN/HDZONE to HDZONE (page 91).
The receiver suddenly power off or
ADVANCED MCACC flashes.
The power unit is damaged. Unplug the receiver from the wall and call a Pioneer autho-
rized independent service company.
FAN STOP is displayed, then
iPod iPhone iPad indicator blinks.
The built-in cooling fan is malfunctioning. Do not try switching the receiver on. Unplug
the receiver from the wall and call a Pioneer authorized independent service company.
No sound
Symptom Remedy
No sound is output when an input
function is selected.
No sound is output from the front
speakers.
Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).
Make sure the correct input function is selected.
Check that the MCACC setup microphone is disconnected.
Make sure the correct input signal is selected (press SIGNAL SEL).
Note that when Fixed PCM ON is selected, you won’t be able to hear any other signal
format (see Setting the Audio options on page 65).
Check that the source component is connected properly (see Connecting your equipment
on page 18).
Check that the speakers are connected properly (see Connecting the speakers on page
21).
No sound from the surround or
center speakers.
Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t
selected; select one of the surround listening modes (see Enjoying various types of play-
back using the listening modes on page 51).
Check that the surround/center speakers are not set to NO (see Speaker Setting on page
86).
Check the channel level settings (see Channel Level on page 87).
Check the speaker connections (see Connecting the speakers on page 21).
No sound from surround back
speakers.
Check that the surround back speakers are set to LARGE or SMALL, and the surround
speakers are not set to NO (see Speaker Setting on page 86).
Check the speaker connections (see Connecting the speakers on page 21). If only one
surround back speaker is connected, make sure it’s connected to the left channel
speaker terminal.
Surround back speakers will not play while the Speaker System is set to Speaker B and
audio is being played through speaker B.
When Speaker System is set to Normal(SB/FH) or Normal(SB/FW) and SP: FH ON or
SP: FW ON is selected with the SPEAKERS button, no sound will be output from the sur-
round back speakers. Select SP: SB/FH ON, SP: SB/FW ON or SP: SB ON (see Switching
the speaker terminals on page 69).
95

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Pioneer-SC-1223

Zoeken resetten

  • Hallo mijn receiver is via lan aan internet verbonden ,bij internet radio valt steeds mijn zender weg en zie ik op het display genre staan ,ik moet dan opnieuw zender selecteren om weer alles terug te krijgen
    gr rob Gesteld op 24-4-2014 om 09:31

    Reageer op deze vraag Misbruik melden
    • Heb je ooit het probleem gevonden? Ik heb dit ook sinds we jaren terug naar UPC over gingen, via ADSL NOOIT problemen gehad. Geantwoord op 26-10-2014 om 19:14

      Waardeer dit antwoord Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer SC-1223 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer SC-1223 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Pioneer SC-1223

Pioneer SC-1223 Snelstart handleiding - Nederlands - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Nederlands - 120 pagina's

Pioneer SC-1223 Snelstart handleiding - Deutsch - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Deutsch - 122 pagina's

Pioneer SC-1223 Snelstart handleiding - English, Français - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Français - 120 pagina's

Pioneer SC-1223 Snelstart handleiding - Italiano - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Italiano - 120 pagina's

Pioneer SC-1223 Snelstart handleiding - Espanõl - 44 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Espanõl - 120 pagina's

Pioneer SC-1223 Gebruiksaanwijzing - Dansk, Svenska - 234 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info