97757
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
Note:
This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.
To avoid shorts in the electrical system, be sure
to disconnect the battery cable before begin-
ning installation.
Refer to the owners manual for details on con-
necting the power amp and other units, then
make connections correctly.
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
Don’t pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
When replacing fuse, be sure to use only fuse of
the rating prescribed on this product.
Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded
or the left and right speaker leads are com-
mon.
Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers
catching fire, emitting smoke or becoming dam-
aged.
When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the cars Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.
To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a pos-
sibility of short-circuiting if the leads are not
insulated.
To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col-
ors correctly.
If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be con-
nected to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours.
The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
Connecting the Units
Fig. 12
Abb. 12
Afb. 12
12. Cap (1*)
When not using this terminal,
do not remove the cap.
18. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
connect to both connectors.
1*
2*
4*
3*
5*
14. Yellow (2*)
To terminal always supplied
with power regardless of
ignition switch position.
16. Red (4*)
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.
13. Yellow (3*)
Back-up
(or accessory)
15. Red (5*)
Accessory
(or back-up)
17. Black (ground)
To vehicle (metal) body.
.
25. Blue/white (7*)
To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
10.
31. Rear Speaker
29. Left 30. Right
26. Blue/white (6*)
27. The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7*
when Pin 5 is an
antenna control type. In another
type of vehicle, never connect 6* and 7*.
21. Connecting cords with RCA pin plugs
(sold separately)
1. This Product
9. Fuse
5. IP-BUS cable
6. IP-BUS input (Blue)
2. Rear output
4. Antenna jack
11. Connect leads of the same
color to each other
7. Jack for Wired Remote Control
Please see the Instruction Manual for the
Wired Remote Control (sold separately).
23.Blue/white
To system control terminal of the power
amp (max. 300 mA 12 V DC).
19.
Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.
32. Perform these connections when using
the optional amplifier.
20. Speaker leads
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
: Front left
+
: Front left
: Front right
+
: Front right
: Rear left
+
: Rear left
: Rear right
+
: Rear right
22. Power amp
(sold separately)
24. System remote control
3. Front output
8. Multi-CD player
(sold separately)
28. Front Speaker
28. Front Speaker
31. Rear Speaker
22. Power amp
(sold separately)
Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this prod-
uct to another product, refer to the supplied
Installation manuals of both products and con-
nect cords that have the same function.
Connecting the Units
<ENGLISH>
Connection Diagram (Fig. 12)
1. This product
2. Rear output
3. Front output
4. Antenna jack
5. IP-BUS cable
6. IP-BUS input
7. Jack for the Wired Remote Control
Please see the Instruction Manual for the Wired
Remote Control (sold separately).
8. Multi-CD player (sold separately)
9. Fuse
10. Note:
Depending on the kind of vehicle, the function of
3* and 5* may be different. In this case, be sure
to connect 2* to 5* and 4* to 3*.
11. Connect leads of the same color to each other.
12. Cap (1*)
When not using this terminal, do not remove the
cap.
13. Yellow (3*)
Back-up (or accessory)
14. Yellow (2*)
To terminal always supplied with power regard-
less of ignition switch position.
15. Red (5*)
Accessory (or back-up)
16. Red (4*)
To electric terminal controlled by ignition switch
(12 V DC) ON/OFF.
17. Black (ground)
To vehicle (metal) body.
18. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.
19. Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connec-
tions.
20. Speaker leads
White : Front left +
White/black : Front left
Gray : Front right +
Gray/black : Front right
Green : Rear left +
Green/black : Rear left
Violet : Rear right +
Violet/black : Rear right
21. Connecting cords with RCA pin plugs (sold
separately)
22. Power amp (sold separately)
23. Blue/white
To system control terminal of the power amp
(max. 300 mA 12 V DC).
24. System remote control
25. Blue/white (7*)
To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
26. Blue/white (6*)
27.The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.
28. Front Speaker
29. Left
30. Right
31. Rear Speaker
32. Perform these connections when using the
optional amplifier.
ACC position
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
No ACC position
CRD3675A 02.10.21 11:18 AM Page 17
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer DEH-P3500MP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer DEH-P3500MP in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Pioneer DEH-P3500MP

Pioneer DEH-P3500MP Gebruiksaanwijzing - Nederlands - 96 pagina's

Pioneer DEH-P3500MP Gebruiksaanwijzing - Deutsch, Français - 100 pagina's

Pioneer DEH-P3500MP Gebruiksaanwijzing - Italiano - 96 pagina's

Pioneer DEH-P3500MP Gebruiksaanwijzing - Dansk, Svenska, Norsk - 92 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info