454828
56
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
AVH-P6400CD
AVH-P6400R
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
Dieses Produkt entspricht den neuen kabelfarben.
Le code de couleur des câbles utilisé pour ce produit est
nouveau.
Questo prodotto è conforme ai nuovi codici colori.
De kleuren van de snoeren van dit toestel zijn gewijzigd.
INSTALLATION MANUAL
MANUEL D’INSTALLATION
1
Contents
Connecting the Units ................................ 1
Connecting the power cord (1) .......................... 3
Connecting the power cord (2) .......................... 5
Connecting the system (A) ................................ 6
Connecting the system (B) ................................ 7
VIDEO Input / Output Connection .................. 8
Attaching the Noise Filters ................................ 8
Installation .................................................. 9
DIN Front/Rear-mount ...................................... 9
DIN Front-mount .............................................. 9
DIN Rear-mount .............................................. 11
CAUTION
PIONEER does not recommend that
you install or service your display your-
self. Installing or servicing the product
may expose you to risk of electric shock
or other hazards. Refer all installation
and servicing of your display to autho-
rized Pioneer service personnel.
Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
Do not drill a hole into the engine com-
partment to connect the yellow lead of
the unit to the vehicle battery. Engine
vibration may eventually cause the insu-
lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take
extra care in securing the wire at this
point.
It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that
it will not obstruct driving.
Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid-
ing mechanism.
Do not shorten any leads. If you do, the
protection circuit may fail to work
properly.
Connecting the Units
2
ENGLISH ESPAÑOL DEUTSCH FRAN
ÇAIS
ITALIANO NEDERLANDS
Note:
This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
ational vehicle, truck, or bus, check the battery
voltage.
To avoid shorts in the electrical system, be sure to
disconnect the battery cable before beginning
installation.
Refer to the owners manual for details on
connecting the power amp and other units, then
make connections correctly.
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake,
and seat rails. Do not route wiring in places that
get hot, such as near the heater outlet. If the insu-
lation of the wiring melts or gets torn, there is a
danger of the wiring short-circuiting to the vehicle
body.
Dont pass the yellow lead through a hole into the
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
When replacing fuse, be sure to use only fuse of
the rating prescribed on the fuse holder.
Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right speaker leads are common.
If the RCA pin jack on the unit will not be used,
do not remove the caps attached to the end of the
connector.
Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers catch-
ing fire, emitting smoke, or becoming damaged.
When this products source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amps system
remote control or the cars Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amps power terminal. Likewise, do
not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.
To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
nused speaker leads without fail. There is a possi-
bility of short-circuiting if the leads are not insu-
lated.
To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col-
ors correctly.
If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be connect-
ed to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours. (Fig.1)
Fig. 1
The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this product
to another product, refer to the supplied
Installation manuals of both products and con-
nect cords that have the same function.
3
Connecting the Units
Connecting the power cord (1)
Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
1*
2*
4*
3*
5*
This product
Antenna jack
11 cm
IP-BUS input
(Blue)
Refer to page 8.
Connect leads of the same color to
each other.
Cap (1*)
When not using this terminal, do
not remove the cap.
AV-BUS input
Lightgreen
Violet/white
Refer to page 5.
Fuse resistor
40 cm
Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.
Red(4*)
To electric terminal controlled by
ignition switch (12 V DC)
ON/OFF.
Fuse resistor
Orange/white
To lighting switch terminal.
Black(ground)
To vehicle (metal) body.
Yellow (3*)
Back-up
(or accessory)
Fuse resistor
Yellow(2*)
To terminal always supplied with
power regardless of ignition
switch position.
Red (5*)
Accessory
(or back-up)
Fuse holder
ISO connector
Note:
In some vehicles, the ISO connector
may be divided into two. In this case,
be sure to connect to both connectors.
4
ENGLISH ESPAÑOL DEUTSCH FRAN
ÇAIS
ITALIANO NEDERLANDS
Subwoofer output or
non-fading output
(SUBWOOFER OUTPUT or
NON-FADING OUTPUT)
15 cm
Rear output
(REAR OUTPUT)
23 cm
Front output
(FRONT OUTPUT)
Connecting cords
with RCA pin plugs
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Blue/white
To system control terminal of the
power amp (max. 300 mA 12 V DC).
System remote control
The pin position of the ISO connector will differ depends on the type of
vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.
Use this for connections when you have the separately
available amplifier.
Subwoofer Subwoofer
Rear speaker
Rear speaker
Left Right
Front speaker
Front speaker
Blue/white (6*)
Blue/white (7*)
To Auto-antenna relay
control terminal
(max. 300 mA 12 V DC).
Note:
Change the Initial Setting of this Product (refer to the
Operation Manual). The subwoofer output of this unit is
monaural.
Speaker leads
White : Front left +
White/black : Front left
Gray : Front right +
Gray/black : Front right
Green : Rear left + or Subwoofer +
Green/black : Rear left or Subwoofer
Violet : Rear right + or Subwoofer +
Violet/black : Rear right or Subwoofer
Fig. 2
5
Connecting the Units
This product
Power cable
Fuse resistor
Violet / white
Of the two lead wires connected to the back lamp, connect the one
in which the voltage changes when the gear shift is in the REVERSE
(R) position. This connection enables the unit to sense whether the
car is moving forwards or backwards.
Light green
Used to detect the ON/OFF status of the parking brake.
This lead must be connected to the power supply side
of the parking brake switch.
Parking brake switch
Power supply side
Ground side
Connecting method
Clamp the parking
brake switch power
supply side lead.
Clamp firmly with
needle-nosed
pliers.
Note:
When you have completed lead wire connection,
perform [VIDEO SETTING] correctly while
referring to the Operation Manual.
It is necessary to set to [BACK UP CAMERA]
in the [VIDEO SETTING] when connecting the
back-up camera.
Note:
The position of the parking brake
switch depends on the vehicle model.
For details, consult the vehicle
Owner’s Manual or dealer.
Connecting the power cord (2)
When using this product with a back-up camera, automatic switching to VIDEO video
when the gear shift is moved to the REVERSE (R) position is possible.
Connect the back-up camera to the VIDEO input.
Fig. 3
6
ENGLISH ESPAÑOL DEUTSCH FRAN
ÇAIS
ITALIANO NEDERLANDS
This product
AV-BUS cable
Black
Not used.
Black
Blue
IP-BUS cable
DVD player
(sold separately) <e.g. SDV-P7>
AV-BUS Output (Black)
IP-BUS cable (supplied with TV tuner)
IP-BUS cable
AV-BUS cable (supplied
with TV tuner)
Blue
AV- B U S
cable
AV-BUS cable
(sold separately)
<CD-AB301E>
40 cm
26 pin RGB input (Yellow)
*1
AV-BUS Input
(Blue)
DVD Navication Unit
(sold separately)
<e.g. AVIC-9DVDII>
Blue
IP-BUS cable
(supplied with the DAB tuner)
Multi-CD player
(sold separately)
IP-BUS cable
Black
Blue
Hide-away TV Tuner
(sold separately)
<e.g. GEX-P6400TVP>
Blue
Black
Black
When a DVD player (e.g. SDV-P7) is not used,
use the AV-BUS cable (supplied with TV tuner)
instead of the AV-BUS cable <CD-AB301E>
(sold separately)*
1
in the figure.
AV-BUS cable
(supplied with TV tuner)
AV-BUS cable
(supplied with TV tuner)
Black
Blue
40 cm
Yellow
Hide-away DAB Tuner
(sold separately)
<e.g. GEX-P700DAB>
Connecting the system (A)
Perform [VIDEO SETTING] correctly while referring to the Operation
Manual.
Fig. 4
7
Connecting the Units
Not used.
Remote sensor
(supplied with Multi-DVD player)
RCA cable (supplied with Multi-
DVD player)
Yellow
(FRONT VIDEO
OUTPUT)
Black
IP-BUS cable (supplied with
Multi-DVD player)
Black
Blue
Multi-CD player
(sold separately)
Multi-DVD player
(sold separately)
< e.g. XDV-P9 >
Blue
Black
Yellow (VIDEO
INPUT or BACK
UP CAMERA)
Blue
Black
IP-BUS cable (supplied
with the TV tuner)
AV-BUS cable
(supplied with
the TV tuner)
Hide-away TV Tuner
(sold separately)
<e.g. GEX-P6400TVP>
Black
Blue
This Product
Connecting the system (B)
Perform [VIDEO SETTING] correctly while referring to the Operation
Manual.
When connecting an XDV-P9
II, refer to the XDV-P9IIs Owners manual.
Fig. 5
8
ENGLISH ESPAÑOL DEUTSCH FRAN
ÇAIS
ITALIANO NEDERLANDS
15 cm
Yellow (rear display output)
(REAR MONITOR OUTPUT)
White, Red (audio input L, R)
(AUDIO INPUT)
To video output
This product
23 cm
Display with
RCA input jacks
Commercially available
portable video component
with RCA output
(or back-up camera)
To audio outputs
Yellow (video input)
(VIDEO INPUT or BACK UP CAMERA)
RCA cable
(sold separately)
To video input
RCA cable (sold separately)
VIDEO Input / Output Connection
Attaching the Noise Filters
1.
2.
To prevent the noise, use the supplied noise
filters correctly.
1. Remove the noise filter from the cords.
2. Attach the noise filters and lock ties as
illustrated.
Noise filter
Lock tie
Perform [VIDEO SETTING] correctly while referring to the Operation
Manual.
Fig. 6
Fig. 7
RCA cables
9
Installation
Note:
Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect-
ed up properly, and the unit and the system work
properly.
Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.
Install the unit where it does not get in the dri-
vers way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.
Do not place the display in a position where it
will impede the drivers visibility or affect the
operation of your vehicles air bags.
The semiconductor laser will be damaged if it
overheats, so dont install the unit anywhere hot
for instance, near a heater outlet.
If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 8)
Fig. 8
30°
DIN Front/Rear-mount
This unit can be properly installed either from Front (conventional DIN Front-mount) or
Rear (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.
DIN Front-mount
Installation with the rubber bush
1. Remove the frame. (Fig. 9)
Fig. 9
Frame
Pull out to remove the frame.
(When reattaching the frame, point the
side with a groove downwards and
attach it.)
10
ENGLISH ESPAÑOL DEUTSCH FRAN
ÇAIS
ITALIANO NEDERLANDS
2. Install side brackets. (Fig. 10)
Fig. 10
3. Fastening the unit. (Fig. 11)
As a rule, secure with side brackets (large).
Fig. 11
Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
182
53
Rubber bush
Screw
Dashboard
Side bracket
(large)
Attach screw
Flush surface screw (5 × 6 mm)
Side bracket
11
Installation
7 When the installation space is not very deep
When installing in a shallow space, secure with side brackets (small). In this case, stick
conceal tape on parts that protrude from the dashboard.
Fig. 12
DIN Rear-mount
Installation using the screw holes on the side of the unit
1. Remove the frame. (Fig. 13)
Fig. 13
Frame
Pull out to remove the frame.
(When reattaching the frame, point the
side with a groove downwards and
attach it.)
Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
182
53
Rubber bush
Screw
Dashboard
Attach screw
Side bracket
(small)
Conceal tape
12
ENGLISH ESPAÑOL DEUTSCH FRAN
ÇAIS
ITALIANO NEDERLANDS
2. Fastening the unit to the factory radio mounting bracket.
(Fig. 14) (Fig. 15)
Select a position where the screw holes of the bracket and the screw holes of this product
become aligned (are fitted), and tighten the screws at 2 places on each side. Use any of
binding screws (4
× 3 mm), binding screws (5 × 6 mm) or flush surface screws (5 × 6
mm), depending on the shape of the screw holes in the bracket.
*1 Use binding screws (4 × 3 mm) only.
Fig. 14
Fig. 15
11
13
12
*
1
*
1
Screw
Dashboard or Console
Factory radio mounting bracket
7
Collegamento delle unità
Non usato.
Sensore per i segnali del telecomando
(fornito con lettore multi-DVD)
Cavo RCA (fornito con lettore
multi-DVD)
Giallo
(FRONT VIDEO
OUTPUT)
Nero
Cavo IP-BUS (fornito con
lettore multi-DVD)
Nero
Blu
Lettore multi-CD
(venduto a parte)
Lettore multi-DVD
(venduto a parte)
<ad es. XDV-P9>
Blu
Nero
Giallo (VIDEO
INPUT or BACK
UP CAMERA)
Blu
Nero
Cavo IP-BUS (fornito
con il sintonizzatore TV)
Cavo AV-BUS
(fornito con il
sintonizzatore
TV)
Sintonizzatore TV
estraibile (venduto a parte)
<ad es. GEX-P6400TVP>
Nero
Blu
Questo prodotto
Collegamento al sistema (B)
Facendo riferimento al manuale di istruzioni, eseguire correttamente
limpostazione video [VIDEO SETTING].
In caso di collegamento del modello XDV-P9
II, fare riferimento al relativo
manuale dellutente.
Fig. 5
56

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer AVH-P6400CD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer AVH-P6400CD in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Pioneer AVH-P6400CD

Pioneer AVH-P6400CD Gebruiksaanwijzing - Nederlands - 224 pagina's

Pioneer AVH-P6400CD Gebruiksaanwijzing - Deutsch, English, Français - 224 pagina's

Pioneer AVH-P6400CD Gebruiksaanwijzing - Français - 224 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info