Handleiding PerfectPro SD1 - Soliddigital (pagina 5 van 33) (Nederlands, Duits, Engels, Frans)

742517

Verklein

Vergroot

Pagina terug

1/33

Pagina verder

5 6

POWER SUPPLY

AC operation

1. Before plugging the AC power cord into the AC socket, be sure the voltage is

correct.

2. AC power cord storage is designed to store the cord when the radio is not in use.

Note:

In order to disconnect the unit from the mains completely, the AC power cord should be

removed from the mains socket completely.

In case of malfunction due to electrostatic discharge or fast transient (burst), remove

and reconnect the power supply.

USING THE RADIO FOR THE FIRST TIME

1. Placetheradioonaatsurface.

2. Carefully extend the telescopic antenna located on the top of the radio.

Adjust the antenna so it is vertically extending above the radio.

3. Plug the AC power cord into the AC socket. The radio will start up and the radio will

automatically perform an auto scan of the Band III DAB channels and the FM band.

The display will show “Scanning” in DAB and “Auto” in FM.

4. When the scan is completed, the 10 strongest FM stations will be stored as presets

and the available DAB stations will be in the list of stations. The radio will switch to

standby with the updated clock and date showing on the display.

DAB RADIO MODE

Operating the radio – DAB

1. Carefully extend the telescopic antenna located on the top of the radio.

Adjust the antenna so it is vertically extending above the radio. Press the On/Off

button to switch on the radio.

2. Select the DAB waveband by pressing the Source button.

3. Therststationinthelistofstationsfoundwillbeplayed.Thedisplaywillshow

the station name. If the radio has been used before, the last used station will be

selected.

4. If no DAB signals are detected, “No stations available” will be displayed. It may

be necessary to relocate the radio to a position with better reception. You should

 thencarryoutanautoscantondstations,pleaserefertothesection“Find new

stations - DAB”.

Selecting a station – DAB

1. Press the On/Off button to switch on the radio. The display will show “Connecting”

and “Playing” for a few seconds.

2. The display shows the name of the radio station currently selected.

3. Rotate the Tuning knob to scroll through the list of available stations.

4. When the desired station name appears on the display, press the Tuning knob to

select the station.

Note: If after selecting a station the display shows “No stations available”, it may be

necessary to relocate the radio to a position with better reception.

Display modes – DAB

In DAB mode, the radio can display a range of information on the display.

Press the Info button to cycle through the various modes.

a. Scrolling text Displays scrolling text message e.g. station information,

artist/track name, phone-in number, etc.

b. Signal strength Displays the signal strength of radio reception. The clear

  unlledrectangleindicatesminimumsignallevelrequired

for satisfactory reception.

c. Program type Displays the type of station being listened to e.g. Pop,

Classic, News, etc.

d. Multiplex name Displays the name of multiplex to which the current

station belongs.

e. Channel & frequency Displays the channel number and frequency for the

currently tuned DAB station.

f. Bit rate & audio format Displays the digital audio bit rate and audio format.

g. Time & date Displays the current time and date.

Finding new stations – DAB

Fromtimetotime,newstationsmaybecomeavailable.Youmayproceedtondnew

stations as follows:

1. In DAB mode, press the Menu button, “Full scan” shows on the display.

2. Press the Tuning knob, the radio will perform a scan of the Band III DAB channels.

As new stations are found, the station counter on the right-hand side of the display

will increase and new radio stations found will be added to the list stored in the radio.

Manual Tuning – DAB

Manualtuningisanalternativemethodofndingnewstations.Insteadofscanningthe

entire Band III channels automatically, you may tune the radio directly to a known DAB

channel and store all the multiplex in that channel into the available station list.

1. In DAB mode, press the Menu button and rotate the Tuning knob until the LCD

display shows “Manual Tune”, then press the Tuning knob. The display will show

DAB channel and Frequency.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

PerfectPro SD1 - Soliddigital Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info