595341
12
Verklein
Vergroot
Pagina terug
1/82
Pagina verder
12 GB/IE
Safety notices specific to the device
where it seized. This can also result in grinding discs
breaking.
Kickback is the result of misuse or incorrect use of
the power tool. It can be avoided by taking the
precautions described below.
a) Maintain a firm grip on the power tool
and position your body and arms to
allow you to brace yourself against
the force of kickback. Always use the
additional handle, if applicable, to
maintain the greatest possible control
over the force of kickback or moment
of reaction whilst running up. The oper-
ator can control kickback and reactive forces
through suitable precautions.
b) Never move your hands near rotating
tools. The tool can move across your hand
during kickback.
c) Avoid the area in front of and behind
the rotating cut-off wheel. Kickback will
move the power tool in the direction opposite the
rotation of the grinding disc where it is seized.
d) Proceed with particular care near cor-
ners, sharp edges, etc. Prevent the tool
from rebounding off the work piece a
nd
jamming. The rotating tool has a tendency
to jam with corner, sharp edges or if it reb
ounds.
This causes a loss of control or kickback.
e)
Do not use chain- or toothed saw blade
s
or segmented diamond discs with
grooves more than 10 mm wide. These
tools will cause kickback or loss of control over
the power tool.
f) Avoid the cut-off disc seizing or apply-
ing excessive contact pressure. Do not
make overly deep cuts. Overloading the
cut-off wheel will increase stress on the disc and
the tendency to twist or seize, thus the potential
of kickback or the abrasive wheel breaking.
g) If the cut-off wheel seizes or you sus-
pend work, switch off the device and
hold it still until the disc stops. Never
attempt to withdraw the running cut-
off wheel from the cut, as this may re-
sult in kickback. Determine and correct the
cause for the jam.
h) Do not restart the power tool so long
as it is in the work piece. Allow the
cut-off wheel to reach its maximum
speed before you carefully continue
cutting. The disc may otherwise get caught,
jump out of the work piece, or kick back.
i) Support boards or large work pieces
to minimise the risk of kickback due
to a jammed cut-off wheel. Large work
pieces can bend under their own weight. The
work piece must be supported at both sides of
the disc, both near the cut and near the edge.
j) Be particularly careful when making
“Pocket cuts“ into existing walls or
other areas which cannot be inspected.
The plunging cut-off wheel can cause kickback
when cutting gas or electrical lines, water pipes
or other objects.
Supplementary Instructions
Approved cut-off wheel designs:
Diamond-tipped, 85 mm disc diameter,
max. 1.8 mm disc thickness
Always wear a dust mask!
Always wear ear protection!
Original accessories / tools
Use only the accessories and attachments de-
tailed in the operating instructions, or those w
hich
are compatible with the device.
Cut-off wheel (symbols)
Wear ear protection!
Wear safety goggles!
Wear solid shoes!
Wear safety gloves!
Safety notices specific to the device / Start-up
12

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Parkside-PTS-500-A1---IAN-103316

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PTS 500 A1 - IAN 103316 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PTS 500 A1 - IAN 103316 in de taal/talen: Nederlands, Duits, Engels, Frans, Zweeds, Fins als bijlage per email.

De handleiding is 1,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info