595354
9
Verklein
Vergroot
Pagina terug
1/53
Pagina verder
9 GB
ATTENTION! In the event of an emergency, imme-
diately activate the emergency stop switch
9
to stop
the cable hoist. The cable hoist cannot be operated
if the emergency stop switch has been activated.
Cleaning, maintenance and
ordering spare parts
Cleaning
ATTENTION! Unplug the mains plug from the
socket before cleaning.
Do not use cleaners or solvents; these could
affect the plastic parts of the device.
Ensure water cannot penetrate the housing.
Keep safety devices, venting slots and the motor
housing as dust and dirt free as possible.
Rub the device down with a clean cloth or
blow out with compressed air at a low pressure
setting.
Regularly clean the device with a damp cloth and
a little soft soap.
Note: We recommend cleaning the device
immediately after every use.
Maintenance
ATTENTION! Verify the device is not connected to
the mains when performing care.
Below: A cycle corresponds to moving a load up
and down once.
Periodic inspection corresponds to an inspection
after 100 cycles.
Periodically check the end switches on the cable
hoist are working properly (check without load).
Test as follows: When the cable reaches the
maximum hoisting height the auto-stop mecha-
nism lever
5
is activated. The motor
14
must
now stop. When the steel cable
6
is unwound
as far as possible, the maximum cable length
lever
4
is activated. The motor
14
must now
stop.
Periodically check the power cable
12
and the
control lead
13
.
Lubricate the steel cable
6
and pulley
15
every
200 cycles.
Every 30 cycles verify the entire steel cable
6
is in good working order in accordance with Fi-
gure I. If damaged, it must be replaced with a
steel cable corresponding with the technical data.
Every 1000 cycles check the screws on the
mounting bracket
1
and pulley
15
are tight.
Every 1000 cycles verify the hooks
8
/
16
and the pulley
15
are in good condition.
Verify the emergency stop switch
9
and push
buttons
10
are in good condition before every
use.
Check the brake system every 1000 cycles. If
the motor
14
emits unusual noises or is unable
to hoist the rated load, the brake system may
need to be overhauled:
- Replace damaged or worn parts and keep
the associated maintenance documentation.
- Please contact an authorised service centre
for unscheduled maintenance work.
Disposal
The device is packaged to protect it from transport
damage. This packaging is a raw material and there-
fore reusable or may be recycled. The device and
its accessories are made from various materials, e.g.
metal and plastics.
Dispose of defective components through toxic waste
disposal. Contact the speciality retailer or your mu-
nicipal government for information!
Do not dispose of power
tools in household waste!
In accordance with European Directive 2012 / 19 /
EU
on waste electrical and electronic equipment and
its implementation into national legislation, worn
out power tools must be collected separately and
recycled in an environmentally friendly fashion.
Operation / Cleaning, maintenance and ordering spare parts / Disposal
Safety notices specific to the device / Before using / Operation
100684_par_Seilhebelzug_content_PL_SI_SK_NL.indd 9 02.07.14 12:41
9

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Parkside-PSZ-250-B2---IAN-100684

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PSZ 250 B2 - IAN 100684 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PSZ 250 B2 - IAN 100684 in de taal/talen: Nederlands, Duits, Engels, Pools als bijlage per email.

De handleiding is 6,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info