779278
16
Verklein
Vergroot
Pagina terug
1/152
Pagina verder
10 GB/IE
9.4 Adjusting the riving knife (fig. 9, 10)
m WARNING:
Pull out the mains plug and wear protective gloves.
m WARNING:
The setting of the saw blade (5) must be checked after every
saw blade replacement.
1. Remove the saw blade guard (4) (see 9.2.1).
2. Remove the table inlay (6) (see 9.3).
3. Set the saw blade (5) to the max. cutting depth (see 10.2).
4. Move the saw blade (5) to the 0° position and lock it in
place (see 10.3).
5. Loosen the fixing screws (33) on the riving knife.
6. Align the riving knife (3) such that
a) the distance between the saw blade (5) and the riving
knife (3) is max. 5 mm (fig. 10) and
b) the saw blade (5) is parallel to the riving knife (3).
7. Tighten the fixing screws (33) on the riving knife again.
8. Fit the table inlay (6) again (see 9.3).
9. Fit the saw blade guard (4) again (see 9.2.1).
9.5 Fitting/replacing the saw blade (fig. 11, 12)
m WARNING:
Pull out the mains plug and wear protective gloves.
1. Set the saw blade (5) to the maximum cutting depth (see
10.2).
2. Undo the screws (34) of the bottom saw blade cover (35)
(fig. 11). Do not remove the screws completely.
3. Push the saw blade cover (35) upwards and open it.
4. Place a 19 mm ring spanner (21) on the nut. Hold against
the motor shaft with another 8 mm ring spanner (20) (fig.
12). To loosen, turn the nut in the rotation direction of the
saw blade.
5. Take off the outer flange and pull the old saw blade down
and off the inner flange at an angle.
6. Clean the saw blade flange carefully with a wire brush
before installing the new saw blade.
7. Put the new saw blade back in reverse order and tighten it.
m WARNING:
Pay attention to the running direction. The cutting angle of
the teeth must point in the running direction, i.e. forwards
(see arrow on the saw blade cover (35) or the saw blade
guard (4)).
8. Close the lower saw blade cover (35) and re-tighten the
screws (34).
m WARNING:
Check the protective devices before working with the saw
again.
9.6 Fitting the parallel stop (7) (fig. 2, 13-14)
1. Fasten the holder (16) to the table with the help of the lock-
ing screws (15) and the clamping plates (15a).
2. Make sure that the holder (16) is aligned parallel to the
saw blade (5). If necessary, readjust it with the aid of the
scales (38).
3. Fasten the stop rail (17) to the holder (16) with the help of
the screws (16a). Note the use of the stop rail (17) for thick
and thin workpieces (see 10.4)
9.7 Fitting the transverse stop (fig. 15)
As an alternative to the parallel stop (7), the transverse stop (2)
can be mounted:
1. Slide the transverse stop (2) into the groove (40) of the
saw table (1).
2. Loosen the turning handle (19).
3. Turn the transverse stop (2) until the arrow points to the
desired angle.
4. Tighten the turning handle (19) again.
5. Fasten the stop rail (17) with the help of the knurled screws
(18) on the transverse stop (2). Note the use of the stop rail
(17) for thick and thin workpieces (see 10.4)
9.8 Chip extraction (fig. 16)
ATTENTION:
Only operate the device with an extraction system.
Connect a suitable chip extraction system (not included in the
scope of delivery) to the extraction port (36).
A household vacuum cleaner is not suitable for use as an chip
extraction system.
ATTENTION:
Check and clean the extraction channels at regular intervals.
NOTE:
To use both extraction nozzles (36 and 4c) at the same time,
use the accessory extraction hose with T-adapter.
Article number: 7901301701 (not included in the scope of
delivery)
9.9 Stable fastening (fig. 17)
The machine must be securely installed, i.e. it must be bolted
down on a workbench, machine stand or similar, as shown in
fig. 17.
Attach the two brackets for workbench mounting (42) to the
front of the machine. Therefore use the screws (43) and the
washers (44).
Use the wood screws (45) to screw the machine on the work-
bench.
10. Handling
10.1 Switch (fig. 1)
10.1.1 On/off switch (11)
It is possible to switch the saw on by pressing the green “I”
button. Before starting sawing, wait until the saw blade has
reached its maximum speed.
In order to switch the saw off again, it is necessary to press
the red “0” button.
10.1.2 Overload switch (10)
In the event of overloading, the motor will switch itself off. After
a cool-down period (time varies) the motor can be switched
back on again.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PMTS 210 A1 - IAN 367465 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PMTS 210 A1 - IAN 367465 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans, Pools, Deens als bijlage per email.

De handleiding is 3.98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info