706381
13
Verklein
Vergroot
Pagina terug
1/33
Pagina verder
11 GB/IE
from rotating and the force of the motor throws
the device back in the direction of the operator.
c) If the sawblade distorts or becomes misaligned
in the saw cut, the teeth at the rear edge of the
sawblade may hook themselves into the work-
piece surface causing the sawblade to move
out of the saw gap and the circular saw to jump
backwards in the direction of the operator.
Special safety advice for circular saws
and automatic blade guards
a) Before you use the saw, always check
that the automatic blade guard
7
clos-
es properly. Do not use the saw if the
bottom compartment of the blade
guard
does not move freely or close immedi-
ately. Never jam or tie the automatic
blade guard in the open position. The
bottom part of automatic blade guard may be-
come bent if the saw falls on to the floor. Open
the blade guard with the release lever and make
sure that it moves freely and does not touch the
saw blade or other parts at all cutting angles
and depths.
b) Check that the spring on the automatic
blade guard functions properly. If the
automatic blade guard or spring does
not function properly, have the device
serviced before you use it. Damaged
parts,
sticky deposits or accumulations of splinters can
delay the operation of the bottom blade guard.
c) Open the automatic blade guard by
hand only for certain cuts such as
plunge
or angle cuts. Open the automatic
blade
guard with the release lever
7 a
and
let it go again as soon as the saw blade
penetrates the workpiece. The automatic
blade guard must be allowed to operate auto-
matically for all saw cuts.
d) Do not put the saw down on a work
bench or the floor without the auto-
matic blade guard covering the saw
blade. If unprotected, a rotating saw blade
moves the saw against the cutting direction and
saws whatever is in its way. Always be aware
that the saw blade takes some time to stop.
Special safety advice for circular saws
and riving knives
a) Use the riving knife matched to the in-
stalled saw blade. The riving knife must be
thicker than the body of the blade but thinner
than the width of the teeth.
b) Adjust the riving knife as described in
the operating instructions. If its thickness,
position or alignment is incorrect, this can lead
to the riving knife not effectively preventing
kickback.
c) Always use the riving knife, except
for plunge cuts. After completing plunge
cutting, put the riving knife back in place. The
riving knife interferes with plunge cuts and can
result in kickback.
d) For the riving knife to work properly,
it must be within the saw gap. The riv-
ing knife is ineffective in preventing kickback
for short cuts.
e) Do not operate the saw if the riving
knife is bent out-of-true. Even a slight defect
can cause the blade guard to close too slowly.
WARNING! Protecting yourself
from laser radiation:
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
P max.: < 1 mW ·
: 650 nm
EN 60825-1: 2007
J Do not look directly into the laser beam or into
the opening from which it is emitted.
General safety advice for electrical power tools
67034_par_Handkreissaege_PHKS1300A1_Content_LB6.indd 11 30.06.11 16:59
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PHKS 1300 A1 - IAN 67034 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PHKS 1300 A1 - IAN 67034 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Parkside PHKS 1300 A1 - IAN 67034

Parkside PHKS 1300 A1 - IAN 67034 Gebruiksaanwijzing - Nederlands, Deutsch, Français, Italiano - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info