634192
56
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
56 GB
OperationOperation
Q
Operation
Never use the device for a purpose for which it was
not intended or with non-original parts / accessories.
The use of tools or accessories other than those rec-
ommended in the operating instructions could lead
to you suffering an injury.
Q
Charging the battery pack
NOTE! A battery pack that has been
unused for a while or never been charged
must be charged before reuse or first use.
The battery pack requires about 3–5 cycles before
it can reach its full charge. The charging process
takes about 180 minutes.
CAUTION! RISK OF INJURY!
Always pull
out the mains plug (
mains adapter
10
) before
you
insert the battery pack into or take it out of
the charger.
Connect the adapter
10
to a mains socket.
Insert the battery pack
3 a
into the charging
cradle
9
. This can only be inserted with the
correct polarity.
The LED
11
lights up green whenever the bat-
tery pack
3 a
is in the charging cradle
9
and
the adapter
10
is connected to a mains socket.
CAUTION! Do not charge a battery pack for
a second time in close succession. There is a
danger of overcharging the battery pack.
Q
Inserting / removing the
battery pack into / out of the
drill / grinder
Inserting the battery pack:
Set the ON / OFF switch
5
to position “0”.
Insert the battery pack
3 a
into the drill / grinder
until it engages.
Removing the battery pack:
Pressing the battery pack buttons
3
at the
sides at the same time allows you to remove
the battery pack
3 a
.
Q
Reading off the battery status
The status or residual power is indicated as follows
in the battery-operated LED
2
whenever the appli-
ance is switched on:
RED / ORANGE / GREEN = maximum charge / power
RED / ORANGE = medium-level charge / power
RED = weak charge recharge battery
Q
Inserting or replacing
a tool / collet
Press the spindle lock
8
and keep it pressed.
Rotate the clamping nut
6
until the lock
engages.
Loosen the clamping nut
6
with the combina-
tion key
23
.
If a tool is already inserted, remove it.
First insert the tool you wish to use through the
clamping nut
6
before you insert it into the
collet
18
suitable for the tool shaft.
Press the spindle lock
8
and keep it pressed.
Insert the collet
18
into the threaded insert and
tighten the clamping nut
6
on the thread using
the combination key
23
.
NOTE: Use the screwdriver end of the combi-
nation key
23
to release or tighten the screw of
the mandrels
13
.
Q
Switching on and off / Setting
the speed range
Switching on / Setting the speed range:
Set the ON / OFF switch
5
to position “I”.
Set the rotational speed control
1
to a position
between „1“ and „MAX.“.
Switching off:
Set the ON / OFF switch
5
to position “0”.
Q
Advice on working with
materials / Tools / Speed ranges
Use the highest speed when working on steel
or iron with the milling bits.
56

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PFBS 9.6 A1 - IAN 78443 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PFBS 9.6 A1 - IAN 78443 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info