679265
13
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
PFBS 12 B2
10 
GB
IE
NI
Charging the integrated battery
NOTE
A new battery or a battery which has not
been used for a long time will need to be
charged before first use/reuse. It will reach its
full capacity after 3–5 charge cycles.
The charging process lasts around 180
minutes.
Starting charging:
Connect the charger
to the charging socket
on the appliance.
Connect the charger
to a mains power
socket.
The battery is fully charged when the battery
LED
shows RED/ORANGE/GREEN.
Stopping charging:
Disconnect the charger
from the mains
power supply.
Disconnect the charger
from the charging
socket
on the appliance.
CAUTION!
Never recharge a battery again immediately
after charging. There is a risk that the battery
will become overcharged.
Checking the battery charge level
If the appliance is switched on, the remaining
charge will be shown on the battery LED
as
follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Changing/inserting the tool/collet
chuck
Press the spindle lock and hold it down.
Turn the tensioning nut
until the lock clicks
into place.
Undo the tensioning nut
from the thread
using the combination spanner
.
Remove any attached tool.
First push the intended tool through the tensioning
nut
before inserting it into the appropriate
collet chuck
for the tool shaft.
Press the spindle lock
and hold it down.
Push the collet chuck
into the thread insert
and screw the tensioning nut
tight with the
combination spanner
.
NOTE
Use the screwdriver side of the combination
spanner
to undo and tighten the screw on
the mandrel .
Switching on and off/setting speed
range
Switching on/setting the speed range:
Set the On/Off switch
to the position "I".
Set the speed control
to a position between
"1" and "MAX".
Switching off:
Set the On/Off switch
to the position "O".
Notes on working with materials/
tools/speed range
Use the milling bits for working on steel and
iron at maximum speed.
Determine the rotational speed range for working
on zinc, zinc alloys, aluminium and copper by
trying it out on test pieces.
Use a low rotational speed for work on plastics
and materials with a low melting point.
Use a high rotational speed for working on
wood.
Carry out cleaning, polishing and buffing work
in the medium speed range.
The following are recommendations only and not
binding. When carrying out practical work, carry
out your own tests to see which tool and which
settings are ideal for the material you are working
on.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PFBS 12 B2 - IAN 305279 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PFBS 12 B2 - IAN 305279 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Parkside PFBS 12 B2 - IAN 305279

Parkside PFBS 12 B2 - IAN 305279 Gebruiksaanwijzing - Nederlands, Deutsch, Français - 52 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info