595417
23
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
23 GB
Introduction / Safety of the fastener driving tool
In correspondence with conditions at the work loca-
tion, individual noise reduction measures may need
to be carried out, such as placing the workpiece on
a noise-suppressing surface, clamping or covering
to prevent workpiece vibration and adjusting to the
minimum pressure required by the work process. In
certain cases, wearing personal hearing protection
is require.
Wear hearing protection!
Vibration values in accordance with
ISO 8662-11:1999:
Vibration emission value a
h,W
= 15.0 m / s
2
Uncertainty K = 0.29 m / s
2
Mechanical impact (vibration)
The vibration value for the fastener driving device was
determined in accordance with ISO 8662-11:1999 —
Hand-held portable power tools – Measurement of
vibrations at the handle — Fastener driving tools
(see technical data). The value is referenced to the
device and does not represent the influence on the
hand-arm system when the device is used. Influence
on the hand-arm system when using the device de-
pends on e.g. gripping force, pressing force, work-
ing direction, air pressure set, the workpiece and its
position.
Safety of the fastener
driving tool
Please read
all the safety information and
instructions. Failure to comply with
the safety instructions and instructions can result in
severe injuries and / or damage to property.
PLEASE RETAIN ALL SAFETY INFORMATION
AND INSTRUCTIONS FOR FUTURE REFERENCE.
Each time before starting work, check
for flawless functioning of the safety
and triggering devices as well as the
firm fit of all bolts and nuts.
Do not conduct any improper manipu-
lation of the fastener driving tool.
Do not dismount or block any part of
the fastener driving tool, such a trig-
ger lock.
Do not conduct any „emergency re-
pairs“ with unsuitable materials.
The fastener driving tool must be reg-
ularly and properly maintained as
specified by the manufacturer.
Prevent anything that would weaken
or damage the device, e.g. by:
– stamping or engraving,
alterations not permitted by the
manufacturer,
guiding on templates made of hard
material, e.g. steel,
permitting to fall onto or slide across
the floor,
– using as a hammer,
– every type of external force.
Work safety
Never point a fastener driving tool that
is ready to use directly at yourself,
other persons or animals.
During work, hold the fastener driving
tool so that head and body can not be
injured by possible kickback due to a
fault in the power supply or from hard
places in the workpiece.
Never trigger the fastener driving tool
into empty space. Following this instruction
will prevent danger due to uncontrolled flying
fasteners and overloading the device.
Before transporting, disconnect the
fastener driving tool from the com-
pressed air network, particularly when
using ladders or are moving with an
unaccustomed body posture.
At the workplace, only carry the fas-
tener driving tool by its grip and never
with the trigger actuated.
Pay attention to workplace conditions.
Fasteners may strike completely through thin
workpieces or slide off corners or edges to
cause a danger to persons.
Introduction
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PDT 40 C2 - IAN 96899 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PDT 40 C2 - IAN 96899 in de taal/talen: Nederlands, Duits, Engels als bijlage per email.

De handleiding is 1,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Parkside PDT 40 C2 - IAN 96899

Parkside PDT 40 C2 - IAN 96899 Gebruiksaanwijzing - Français - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info