722890
11
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
PABH 20-Li A1
8
 GB
IE
Release the locking sleeve of the SDS bit
adapter . This locks the holder. Check that
the tool with the hexagonal shank is properly
locked by pulling it. The tool with the hexagonal
shank has radial play because of the design.
Removing a tool with a hexagonal
shank
Pull the locking sleeve backwards and remove
the tool with the hexagonal shank.
Operation
Select operating mode
Use the “Drill/hammer drill” switch to select
the operating mode of the power tool.
NOTE
Change the mode only when power tool is
switched off. Otherwise, the tool could be
damaged.
To change the operating mode, turn the “Drill/
hammer drill” switch
to the desired position.
Hammer drilling = Hammer ON
Drilling/screwing = Hammer OFF
Setting the rotation direction
NOTE
Operate the rotation direction switch
only
when the appliance is at a standstill.
You can use the rotation direction switch
to
change the direction of rotation of the power
tool. This is not possible, however, while the on/
off switch is pressed in.
Clockwise:
For drilling and screwing in screws, turn the
rotation direction switch
to the left as far
as the stop.
Anti-clockwise:
For undoing and removing screws and nuts, turn
the rotation direction switch
to the right as
far as the stop.
Switching on/off
Switching on:
To start the power tool, press the on/off switch
and keep it pressed in.
The lamp
lights up when the on/off switch
is pushed in slightly or fully and illuminates the
working area in low light conditions.
Switching off:
To switch off the power tool, let go of the on/
off switch
.
At low temperatures, the power tool will only
reach its full hammer performance/strike power
after a certain time.
To save energy, do not switch the power tool
on unless you plan to use it.
Set drill/hammer speed
You can infinitely adjust the drill/hammer speed
of the switched on power tool, depending on
how far the on/off switch is pressed in.
Pressing the on/off switch lightly yields a
low drill/hammer speed. Increasing pressure
increases the speed.
Run-on brake:
When you release the on/off switch
, the
brake stops the chuck and prevents run-on of
the tool.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside PABH 20-Li A1 - IAN 277022 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside PABH 20-Li A1 - IAN 277022 in de taal/talen: Nederlands, Duits, Engels, Frans, Deens als bijlage per email.

De handleiding is 0,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info