744927
52
Verklein
Vergroot
Pagina terug
1/70
Pagina verder
52 GB/MT
to twist or snag in the cut, making kickback or
disc breakage more likely.
b) Avoid the area in front of or behind
the rotating cutting disc. If the cutting disc
is moving away from you at the point of con-
straint in the workpiece, then, in the event of
a kickback, the electrical power tool and the
rotating disc may be thrown towards you.
c) If the cutting disc jams or you stop
work for a while, switch the device
off and hold it until the disc comes to
a complete stop. Never attempt to
pull the still rotating cutting disc out of
the cut as this could cause kickback.
Determine and rectify the reason for the jamming.
d) Do not switch on the device if the cut-
ting disc is in the workpiece. Allow
the cutting disc to reach full speed be-
fore carefully continuing with the cut.
Otherwise the disc could snag, jump out of the
workpiece or cause a kickback.
e) Support boards or workpieces whilst
cutting to reduce the risk of kickback
caused by a jammed cutting disc. Large
workpieces may bend under their own weight.
The workpiece must be supported to both sides
of the cutting disc and particularly near the
cutting disc and at the workpiece edge.
f) B
e particularly careful when pocket
cutting in existing walls or other areas
where you cannot see what you are cut-
t
ing into. The cutting disc plunged into the surface
could cut through gas or water pipes, electricity
cables or other objects and cause kickback.
Q
Special safety advice for
abrading using sandpaper
Do not use over-sized sanding sheets.
Follow the manufacturer’s recommen-
dations for sanding sheet size. Sanding
sheets that project beyond the backing pad
could cause injury in addition to jamming,
tearing of the sheet or kickback.
Q
Special safety
advice for polishing
Do not use the polishing bonnet if it
has any loose parts, in particular the
fastening cords. Tuck the fastening cords
away or trim them. Loose fastening cords rotat-
ing with the attachment could catch your fingers
or become trapped in the workpiece.
Q
Special safety advice for
working with wire brushes
a) Bear in mind that wire brushes lose
pieces of wire during normal use. Do
not overload the wires by applying too
much pressure. Flying pieces of wire can very
easily penetrate thin clothing and / or skin.
b) U
se a guard, if recommended, but m
ake
sure that the wire brush does not come
into contact with the guard. The diameters
of disc brushes and cup brushes can increase
due to contact pressure and centripetal forces.
Device-specific safety
instructions for small drill
PMGS 12 B2 and mains
adapter-PMGS 12 B2-1
When you use the drill /
grinder wear the following
protective equipment: safety glasses
and protective gloves.
CAUTION! The tool continues to rotate
after it has been switched off!
Avoid contact with rapidly rotating
drill / grinder components.
Securely support the
workpiece. Use clamps or a vice to grip the
workpiece firmly. This is much safer than holding
it in your hand.
Never support your-
self by placing your hands near or in
front of the device or the workpiece
surface. A slip can result in injury.
General safety advice for electrical power tools / OperationGeneral safety advice for electrical power tools
52

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 66445 PMGS 12 A1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 66445 PMGS 12 A1 in de taal/talen: Engels, Portugees, Spaans als bijlage per email.

De handleiding is 2,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Parkside IAN 66445 PMGS 12 A1

Parkside IAN 66445 PMGS 12 A1 Gebruiksaanwijzing - Nederlands, Deutsch, Français, Italiano - 57 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info