748074
32
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
32
GB IE
7. Move the machine with protruding tem-
plate guide (25) along the template.
Apply slight pressure during this work.
The template must be at least as
high as the ball race (26) of the
template guide (25).
Milling with centring tip
By means of the centring tip, you can do
circular milling work.
1. Turn the parallel stop (24) around so
that the stop edge points up.
2. Screw on the centring tip (23) on the
parallel stop by means of the buttery
nut. In the process, counter lock the
centring tip in the long hole of the com-
bination wrench (
27).
3. Screw the guide bars (29) of the paral-
lel stop (24) on the baseplate (10) and
tighten the retaining screws (9).
4. Push the centring tip (23) in the marked
centre of the circle to be cut.
5. Move the machine circularly once in
the circle around the centring tip (23).
Cleaning/maintenance
Ask our service centre to carry out
any work that is not described in
these instructions. Use only original
parts. In this way you avoid dam-
age to the appliance and possible
injury to people.
Pull out the power plug before car-
rying out any work on the equip-
ment. There is a risk of electrocution
or of injury from moving parts.
Milling with parallel stop
You can mill notches and proles with the
parallel stop by moving the parallel stop
along the workpiece edge at a pre-set
distance.
1. Insert the parallel stop (24) with
the guide bars (29) into the guide
rails (15) of the baseplate (10).
Tighten the retaining screws (9).
2. Move the turned on machine
along the workpiece edge with
lateral pressure on the parallel
stop (24).
Milling with template
guide
By means of the template guide (25), you
can transfer contours from templates to
workpieces.
Inserting the template guide:
1. Screw off the suction adapter as applies.
2. Insert the template guide (25) into the
sliding plate (11). The ball race (26)
must point down.
3. Fasten the template guide (25) to the
recessed head screws (21) that are in-
cluded in the delivery.
Inserting the cutter:
4. Insert a cutter that has a diameter
smaller than the inner diameter of the
template guide (25).
5. Set the desired cutting depth (see “Ini-
tial operation”).
Milling with template guide
6. Loosen the clamping lever
(
19) and lower the machine down-
ward until the previously set cutting
depth is reached.
32

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 304379 POF 1200 C2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 304379 POF 1200 C2 in de taal/talen: Nederlands, Duits, Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 3,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info