746858
32
Verklein
Vergroot
Pagina terug
1/117
Pagina verder
GB/IE/NI32
Operation
of connecting to the compressed air system, and
tool effectiveness and life is extended as a result.
Connecting sleeve
Compressed air hose
Quick release connector Compressor
Pressure regulator
Oiler Filter
Quick release connector
Quick release connector
Before first use and thereafter at regular intervals,
apply a few drops of pneumatic equipment or
motor oil SAE 10-20 into the compressed air
connection on the pneumatic device. After every
3–4 operating hours, use the assembly key to
remove the screw plug
9
in the oil reservoir.
Fill the oil reservoir with pneumatic equipment or
motor oil SAE 10-20, and insert the screw plug
back. Wrap some Teflon sealing tape around the
thread on the air connections. Screw the air con-
nections into the pneumatic devices.
Starting up
Put on protective clothing and goggles.
OTHERWISE THERE IS DANGER OF INJURY!
Check that the parting disc has been tightened
securely.
Check that the workpiece is supported or has been
locked in place correctly. A C clamp is recom-
mended on loose workpieces.
Make sure that generated sparks do not pose any
danger, i.e. they cannot contact any persons or
ignite flammable substances.
Connect the compressed air supply. To do so, con-
nect the compressed air source to the compressed
air connection.
Press the switch ON guard towards the chuck.
Press the trigger arm, and perform the cutting work.
The device rotates at the maximum speed when the
trigger arm is tightened to the stop. Regulate the
tightening pressure and therefore the speed for the
optimal grinding results.
Switching OFF
Release the trigger arm
2
to switch OFF the
pneumatic angle grinder.
After work, disconnect the device from the
compressed air source.
Note: First detach the hose from the compressed
air source, and then remove the supply hose from
the device. This prevents the supply hose from
whirling out of control.
Maintenance
If the machine is to enjoy a long service life and
operate without problems, it is important that the
following maintenance instructions are followed.
The pneumatic angle grinder must be lubricated
regularly if it is to operate flawlessly at all times.
ATTENTION: DISCONNECT COMPRESSED AIR
BEFORE MAINTENANCE WORK!
Keep the pneumatic devices clean.
Turn over the tool so that the compressed air con-
nection points upwards, and apply a few drops of
pneumatic equipment or motor oil SAE 10-20 into
the compressed air connection on the pneumatic
devices.
Press the trigger arm
7
to distribute the oil more
evenly. Hold a cloth or absorbent paper towel in
front of the exhaust air openings, and let the device
run in idle mode for a few seconds.
ATTENTION! EXCESS OIL IS BLOWN OUT. KEEP
THE DISCHARGE HOLE AWAY FROM PERSONS
AND OBJECTS.
32

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 292193 PDTS 6.3 A1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 292193 PDTS 6.3 A1 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info