746866
25
Verklein
Vergroot
Pagina terug
1/90
Pagina verder
PDSS 16 A1
22 
GB
IE
Switching on and off
Switching on:
First, press the trigger lock
forwards and
then the trigger down to switch the tool on.
Switching off:
Release the trigger
.
When you have finished working, disconnect
the tool from the compressed air source.
Maintenance and cleaning
WARNING! RISK OF INJURY!
Disconnect the tool from the
compressed air supply.
CAUTION!
Before maintenance, clean off any hazardous
substances that may have accumulated on
the tool (due to working processes). Avoid
all skin contact with these substances. If the
skin comes into contact with hazardous dusts,
this can lead to severe dermatitis. If dust is
produced or swirled up during maintenance,
it can be inhaled.
NOTE
To ensure correct functioning and a long
service life for the tool, pay attention to the
following points:
Sufficient and continuous oil lubrication is highly
important for optimum functioning.
Check the speed and vibration levels after each
use.
Check the idle speed regularly and after any
maintenance is performed:
use a rev counter and perform the measure-
ment without any clamped tools. At a residual
pressure of 6.3 bar, the idle speed may not be
exceeded under any circumstances.
If the tool is exhibiting excessive vibration levels,
the cause of the vibrations must be identified
and repaired.
Use only the genuine replacement parts recom-
mended by the manufacturer, otherwise you
could put users at risk. In doubt, contact the
Service Centre.
Clean the tool with a soft, dry cloth only.
Never use sharp or abrasive cleaning agents
under any circumstances.
Troubleshooting
Fault Possible
cause
Remedy
Speed too
slow, air
escapes from
the outlet.
Motor parts
jamming due
to dirt.
Check the
pressure sup-
ply filter for
contamination.
Pressure sup-
ply too low.
Check the
pressure sup-
ply filter for
contamination.
Lubricate the
tool as de-
scribed in the
instructions.
If necessary,
repeat the
steps outlined
above.
Tool does
not move;
compressed
air escapes
completely
through the
outlet.
Motor is
jammed due
to material
build-up.
Lubricate the
tool as de-
scribed in the
instructions.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 292167 PDSS 16 A1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 292167 PDSS 16 A1 in de taal/talen: Nederlands, Duits, Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 3,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info