745550
11
Verklein
Vergroot
Pagina terug
1/62
Pagina verder
12 GB/IE
Commissioning / After initial use / Maintenance
Adjusting the compressed air
Note: this device is designed for an operating
pressure of up to 6.8 bar and a compressor with
the minimum air flow specified in the technical spe-
cifications. When setting the air pressure, remem-
ber the pressure drops by approx. 0.6 bar with a
hose length of 10 m and an inner diameter of
9 mm.
Only use filtered, lubricated and regulated
compressed air.
Initial use
Activate the On / Off switch
3
to start using
the device.
Release the On/ Off switch
3
to switch the
device off.
Changing rotation
ATTENTION! The device must come to a
complete standstill before changing the direc-
tion of rotation.
ATTENTION! A machine rotating in an unex-
pected direction can be dangerous. Always
pay attention and use care.
Note: The power drill is designed for clock-
wise/counter-clockwise rotation. Use the
forward/reverse switch
4
to change the
direction of rotation of the power drill.
Set the forward/reverse switch
4
to position F
to switch to clockwise rotation.
Set the forward/reverse switch
4
to position R
to switch to counter-clockwise mode.
After initial use
Once the task has been finished the device must be
disconnect from the compressed air supply
5
.
Briefly activate the On / Off switch
3
on the
device to bleed any residual compressed air.
Now pull back the safety on the connection
coupling of your compressed air hose.
Now remove the hose from the plug nipple
8
.
Careful when putting the device
down. Always put down the device so it does
not rest on the trigger. This could potentially re-
sult in inadvertent activation of the tool, which
in turn could result in hazards.
Maintenance
ATTENTION! All maintenance must be per-
formed by trained individuals. Follow the specified
maintenance instructions to ensure a long life and
proper operation of this quality product.
Disconnect equipment from the compressed air
source when performing maintenance and care.
Check the condition of wear and tear items
and accessories with each maintenance.
Note: Daily cleaning and regular lubrication
are an absolute necessity for smooth operation.
Only use special tool oil with a high viscosity
(thin fluid). Oil for compressed air tools or
SAE10-20 motor oil are suitable.
ATTENTION! Do not use other (especially
high viscosity) lubricants. Malfunctions or per-
manent damage may otherwise occur.
The following lubricating options are
available:
a) via oil-mist generator
To use the oil-mist generator plug the plug
nipple
8
directly into the equipment and con-
nect with your air hose.
b) by hand
Alternatively you can also manually lubricate
your equipment (not recommended).
To do so, remove the screw plug on the oil filler
port.
Apply 3–5 drops of oil to the compressed air
connection before using the compressed air
tool
4
.
If the air tool has not been used for several
days 5–10 drops of oil must be added to the
air connection
5
.
... / Cleaning and Care / Information about warranty and service processing
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 275685 PDBS 2200 A2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 275685 PDBS 2200 A2 in de taal/talen: Nederlands, Duits, Engels, Frans, Deens als bijlage per email.

De handleiding is 1,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info