745526
12
Verklein
Vergroot
Pagina terug
1/66
Pagina verder
9
PDEXS 150 B2
GB
IE
Operation
Switching on and off
Switching on:
First press the locking mechanism forwards and
then the trigger
to switch the appliance on.
Switching off:
Let go of the trigger
.
When you have finished working, disconnect
the appliance from the compressed air source.
Regulation of vibration output
Use the speed controller
to control the air-
flow and thus the vibration output (also during
operation).
The ideal speed depends on the material being
worked and can be determined through practical
tests.
Use the pressure reducer to set the correct working
pressure.
Sanding
Switch on the compressed air source and allow
it to run until the maximum tank pressure has
been reached.
Use the pressure reducer on the compressed
air source to set the optimum working pressure.
Note that the maximum working pressure may
not be exceeded. An excessive working pres-
sure does not mean increased output; it merely
increases the air consumption and accelerates
appliance wear. Always comply with the techni-
cal information.
Switch on the compressed air-powered random
orbital sander.
Allow the device to reach the required speed
and adjust as necessary.
Guide the compressed air-powered random
orbital sander parallel onto the workpiece.
Move the appliance parallel and in flat circles
or alternatively lengthwise and across the sur-
face. Use the housing
as a handle to guide
the appliance in the desired direction.
Do not press the compressed air-powered ran-
dom orbital sander down. Pressing down hard
does not increase the working efficiency!
When you have finished working, let go of the
trigger
to switch off the appliance.
When you have finished working, disconnect
the appliance from the compressed air source.
CAUTION!
Sanding creates dust. Always wear protective
gloves, a suitable mask and clean the sand-
paper and workpiece at regular intervals with
a vacuum cleaner or compressed air.
Suitable safety precautions must be taken
depending on the size and nature of the
workpiece. Use suitable clamping devices to
prevent the workpiece from slipping.
In the event of an interruption to the air sup-
ply, release the trigger
immediately.
Working procedures
The most important thing to remember when sand-
ing is to use successively finer grained paper.
With a coarse grain, the surface will not become
smooth, but rather rougher. If the grain is too fine,
you will hardly achieve any noticeable result.
The material removal rate is determined by the
speed and grain size of the sandpaper.
The sandpaper used should be appropriate to the
substance being worked and the amount of mate-
rial to be removed.
CAUTION!
Ensure that the appliance is disconnected
from the compressed air source before you fit
or remove a sandpaper disc
.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 275679 PDEXS 150 B2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 275679 PDEXS 150 B2 in de taal/talen: Nederlands, Duits, Engels, Frans, Deens als bijlage per email.

De handleiding is 0,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info