745222
14
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
14
GB IE
Grinding with the wet
grinding disc
Stand in front of the wet grinding disc
(
1).
Hold the workpiece with both hands
and lower it slowly onto the wet grind-
ing disc.
The workpiece can also be supported
on the teeth of the water tank (
13).
Change grinding disc
Information on replace-
ment:
Never operate the device without
protective equipment.
Ensure that the rotation speed
stated on the grinding disc is the
same or higher than the nominal
rotation speed of the device.
Ensure that the grinding disc
dimensions match those of the
device.
Only use awless grinding discs
(sound test: an undamaged grind-
ing disc hanging freely on a
string will result in a clear sound
if it is tapped with a plastic ham-
mer).
Never re-drill a locating hole
which is too small to make it
larger.
Never use separate bushings or
adapters in order to make grind-
ing discs whose hole is too large
t the device.
Do not use any saw blades.
To clamp the grinding tools only
use the clamping ange provid-
ed. The pads between the clamp-
ing ange and the grinding tools
must be made of elastic materials
e.g., rubber, soft cardboard etc.
Always reassemble the device
completely after replacing the
grinding disc.
Switch the device off and remove
the mains plug.
Allow the device to cool down.
Wear protective gloves when
changing the grinding discs in or-
der to avoid cutting damages.
Change dry grinding disc
1. Loosen the xing screws and re-
move the grinding disc cover (25).
2. Unscrew the grinding disc nut (22)
with a screw wrench (SW19) and
hold against the grinding disc
with one hand wearing a glove.
Unscrew the nut (right-hand th-
read): turn counter-clockwise.
3. Remove the clamping ange (23)
and the grinding disc (5).
4. Fit on the new grinding disc
(5) with the intermediate card-
board layers (24) and the clam-
ping ange (23), and screw the
grinding disc nut (22) manually
onto the nut (right-hand thread):
turn clockwise.
5. Tighten the grinding disc nut with
a screw wrench (SW19) applying
modest manual force.
6. Screw the grinding disc cover
(25).
7. Adjust the spark protection holder
(
18) and the workpiece sup-
port (
6) - the distance to the
grinding disc
(5) is max. 2 mm (see „Assem-
bly“)
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside IAN 115727 PNTS 250 A1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside IAN 115727 PNTS 250 A1 in de taal/talen: Nederlands, Duits, Engels als bijlage per email.

De handleiding is 4,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Parkside IAN 115727 PNTS 250 A1

Parkside IAN 115727 PNTS 250 A1 Gebruiksaanwijzing - Français - 56 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info