763673
13
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
8GB/IE
8. Before starting the equipment
Open the packaging and remove the device carefully.
Remove the packaging material as well as the packaging
and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport damage.
If possible, store the packaging until the warranty period
has expired.
m DANGER
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
8.1 Mounting the transport handle (fig. 3.1)
ATTENTION! The correct position of the transport handle (39)
is specified by a groove.
Mount the transport handle (39) on the machine head (4)
using the Phillips screws 5.0 x 25 mm.
Then tighten the two Phillips screws 5.0 x 25 mm (40) with a
Phillips screwdriver (not included in the scope of delivery).
8.2 Setting up the machine (fig. 3.2)
The machine must be set up where it can stand securely.
Secure the machine on a workbench, base frame or similar.
Insert 4 screws (not included in the scope of delivery) into
the holes on the fixed saw table (15).
Tighten up the screws.
8.3 Installing the tilt protection (fig. 3.2)
Loosen the tilt protection (36) pre-installed at the bottom of
the saw.
Pull the tilt protection (36) out, so that it can still be fixed
with the aid of the Allen screws.
Secure the tilt protection again with an Allen key (D).
8.4 Setting the adjustment screw (fig. 3.3)
Set the adjustment screw (37) to the level of the tabletop to
avoid wobbling of the machine.
8.5 General information
All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
It must be possible for the blade to run freely.
When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
Before you press the ON/OFF switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
Before you connect the equipment to the power supply make
sure the data on the rating plate are identical to the mains
data.
8.6 Checking the moving saw blade guard safety
device (5)
The saw blade guard protects against accidental contact with
the saw blade and from chips flying around.
8.6.1 Check function
To do so, fold the saw downwards:
The saw blade guard must provide free access to the saw
blade without touching other parts.
When folding the saw upwards into the starting position, the
saw blade guard must cover the saw blade automatically.
9. Attachment
You need:
1x Allen key 6 mm (C)
1x Allen key 3 mm (D)
(included in the scope of delivery)
1x open-ended spanner 13 mm
1x Phillips screwdriver
(not included in the scope of delivery)
9.1 Attaching the multifunction sliding cross cut mi-
tre saw (fig. 1/2/3.3/4)
In order to adjust the rotary table (14), fold the locking han-
dle (11) upwards and pull up the latched position lever (35)
with your index finger.
Turn the rotary table (14) and pointer (12) to the desired
angle measurement of the scale (13). To fix the setting, fold
the locking handle (11) downwards.
Press the machine head (4) lightly downwards and remove
the locking bolt (23) from the motor bracket. Thus, the saw
disengages from the lowest position.
Swing the machine head (4) up.
It is possible to secure the clamping devices (7) to the left or
right on the fixed saw table (15). Insert the clamping devices
(7) into the holes provided on the back of the stop rail (16)
and secure them with the wing screws (7a).
For 0°- 45° mitre cuts, the clamping device (7) must only be
mounted on the right side (see fig. 14-15).
It is possible to tilt the machine head (4) a max. 45° to the
left by loosening the set screw (22).
Workpiece supports (8) must always be secured and used
during work. Define the desired table size (see 9.1.1.).
9.1.1 Defining the table size
Loosen the set screw (9).
Pull out the workpiece support (8) to the desired table size.
Tighten the set screw (9) again.
9.2 Chip collection bag (fig. 1/5)
The saw is equipped with a chip collection bag (17) for saw-
dust and chips.
Attention! The chip collection bag may only be used when
cutting wood and wood-like materials! When cutting metal,
there is a risk that hot chips will ignite the chip collection bag.
Squeeze the wings of the metal ring on the chip collection bag
(17) together and slide it over the extraction port (17a) near
the engine.
The chip collection bag (17) can be emptied by means of a
zipper at the bottom.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Parkside 360564 - IAN 360564 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Parkside 360564 - IAN 360564 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans, Pools, Deens als bijlage per email.

De handleiding is 4,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info