Standby/on switch [^ ], [8 ] (4, 6)
Press to switch the unit from on to standby
mode or vice versa. In standby mode, the
unit is still consuming a small amount of
power.
[DIMMER]
Dims the display panel. Press again to
cancel.
Numeric buttons [1-9, 0,
≧
10] (4, 5, 8, 9)
To select a 2-digit number
e.g. 16: [
≧
10] [1] [6]
To select a 3-digit number
e.g. 226:
≧
10] [
≧
10] [2] [2] [6]
[DEL] (4)
[PROGRAM] (4, 5)
[REPEAT] (4)
[PLAY MODE] (4, 5)
[USB q /h ] (8)
[CD q /h ] (4)
[u /t ], [y /i ] (4, 5, 8)
[RE-MASTER] (7)
[BASS] (7)
[e, r ], [w , q ] (4, 6, 7, 8)
[OK] (4, 6, 9)
[DISPLAY] (4, 5)
[AUTO PRESET] (5)
[TUNE MODE] (5)
[z , PLAY] (6)
[CLOCK/TIMER] (6)
[AUTO OFF]
This function allows you to turn the unit off
(except in radio mode) after the unit is left
unused for about 30 minutes. Press twice
to turn it on.
[SLEEP] (6)
[+, VOL , –], [– VOLUME +]
[MUTE]
Mutes the sound. Press again to cancel.
“MUTE” is also cancelled when the volume
is adjusted or the unit is turned off.
[AUX] (1)
[RADIO] (5)
[g ] (4, 8)
[D.BASS] (7)
[PRESET EQ] (7)
[TREBLE] (7)
[SURROUND] (7)
[INPUT LEVEL] (1)
[FM MODE] (5)
[FM/AM/AUX] (5, 9)
[CD ; , OPEN/CLOSE] (4)
USB port (8)
Remote control signal sensor
Aim the remote control at the sensor,
avoiding obstacles, at a maximum range of
7 m directly in front of the unit.
Preset Press [PRESET EQ] repeatedly to select “HEAVY”, “SOFT”, “CLEAR”,
“VOCAL” or “FLAT”.
Bass
Press [BASS] or [TREBLE] to select “BASS” or “TREBLE”.
Press [e, r ] to adjust the level (-4 to +4).
Surround Press [SURROUND] repeatedly during play to select “ON SURROUND”
or “OFF SURROUND”. If interference in FM stereo reception increases,
cancel the surround sound effect.
D Press [D.BASS] repeatedly during play to select “ON D.BASS” or
“OFF D.BASS”.
Re-master (MP3) Press [RE-MASTER]
“OFF
7
Sound adjustment
5
Radio operations
The
play
Preparation:
Before connecting any USB mass storage
device to the unit, ensure that the data stored
therein has been backed up.
It is not recommended to use a USB extension
cable. The device connected via the cable will
not be recognised by this unit.
Reduce the volume and connect the USB
mass storage device.
Press [USB q /h ] to start play.
•
•
USB
Stop
Press [g ].
display
memorised.
Press [USB q/ h]
play
Press [g ]
position.
To remove the USB mass storage device,
select a source other than “USB”.
Removing the USB mass storage device with
it selected as a source can damage the data
stored in the device.
•
For other operating functions, they are similar
as those described in “Disc operations”
(➡ Section 4).
USB operations
External unit
8
Devices which are defined as USB mass
storage class:
USB devices that support bulk only transfer
USB devices that support USB 2.0 full speed
•
•
Compatible devices
Stop
Press [g ].
P
Press [CD q/ h].
again
Skip
Press [u/ t ]
[y/ i ].
Search
current
(CD)
Press [u/ t ]
[y/ i ].
Skip
(MP3)
Press [e ,r ].
Direct
play
(Play
the
select.)
CD: Press the numeric
buttons to select the
track.
MP3: [e ,r ] to
select the album.
[y /i]
once and then the
numeric buttons to
select the track.
Basic play
Press [DISPLAY] repeatedly during play or
pause to view the current track’s information.
Maximum number of displayable characters:
approximately 30
This unit supports ver. 1.0 and 1.1 ID3 tags.
Text data that is not supported will not be
displayed.
•
•
Press [CD q /h ].
Press [PLAY MODE] repeatedly to select
the following modes.
Mode To play
1TR
1-TRACK
one
disc.
Press
to
1ALBUM
1-ALBUM (MP3)
one
disc.
Press [e ,r ]
album.
RND
RANDOM
a
1ALBUM
1-ALBUM
RANDOM (MP3)
all
album
Press [e ,r ]
album.
During random play, you cannot skip to the
previous track.
The current play mode is cleared when you
open the sliding door.
To repeat program play or selected play mode,
press [REPEAT] . Press again to cancel.
•
•
•
Play Mode function
Cancel
mode
Press [PROGRAM] in
stop
indicator
Replay
program
Press [PROGRAM] in
stop then
[CD q/ h].
Check
contents
Press [u/ t ] [y/ i ]
when
the
programming,
[PROGRAM]
“PGM”
press [u/ t ] [y/ i ].
Delete
programmed
track
Press [DEL] in
Clear
programmed
tracks
Press [g ] in
“CLR
5
again
The program memory is cleared when you open
the sliding door.
•
Display function
Disc operations
4
Press [^ ] to turn the unit on.
Press [CD ; , OPEN/CLOSE] on the main
unit to open the sliding door.
Tilt the disc into the disc tray under the
sliding door and then set the CD in place.
Press [CD ; , OPEN/CLOSE] to close the
sliding door.
Keep fingers away from the sliding door when
it is closing to avoid possible minor injuries.
Press [CD q /h ] to start play.
Damage may occur if the sliding door is forced
closed.
Be careful of CD hitting the sliding door while
being removed.
•
•
Program play
Enables
q/ h] g ].
Press [PROGRAM].
CD:
select the track.
To program more tracks, continue by
pressing the numeric buttons.
Press [OK] or [CD q /h ] to start play.
■ Batteries (not included)
Use a manganese dry battery or an alkaline dry battery.
Insert so the poles (+ and –) match those in the remote control.
Remove if the remote control is not going to be used for a long period of time.
Store in a cool and dark place.
Do not heat or expose to flame.
Do not leave the batteries in an automobile exposed to direct sunlight for a long period of time with
doors and windows closed.
Mishandling of batteries in the remote control can cause electrolyte leakage, which may cause a fire.
•
•
•
•
•
•
•
■ Do not:
mix old and new batteries.
use different types of batteries at the same time.
take apart or short-circuit the batteries.
attempt to recharge alkaline or manganese batteries.
use the batteries if the coverings have been peeled off.
•
•
•
•
•
R6/LR6, AA
Place
Preparing the remote control
2
Control guide
3
Press [RADIO] to select “FM” or “AM”.
Press [TUNE MODE] to select “MANUAL”.
u /t ] or [y /i ] to select the
frequency of the required station.
To tune automatically
Repeat step and (➡ above).
Press and hold [u /t ] or [y /i ] until
the frequency starts changing rapidly.
To cancel auto tuning, press [u /t ] or
[y /i ] once again.
Auto tuning may not function when there is
excessive interference.
To improve FM sound quality
Press [FM MODE] to display “MONO”
indicator. Press again to cancel.
“MONO” is also cancelled if the frequency is
changed.
Turn “MONO” off for normal listening.
To improve AM sound quality
Press [RADIO] to select “AM”.
Press and hold [TUNE MODE] repeatedly
to change the beat proof setting (“BP 1” or
“BP 2”).
•
•
•
•
Y
channels.
Preparation:
Press [RADIO]
Manual tuning
Memory preset
RDS display may not be available if the
reception is poor.
•
Station
Name
Program
T
F
display
Press [DISPLAY] to display.
Manual presetting
Press [TUNE MODE] to select “MANUAL”.
Press [u /t ] or [y /i ] to tune to the
required station.
Press [PROGRAM].
Press the numeric buttons to select a
channel.
The station occupying a channel is erased if
another station is preset in that channel.
To preset more stations, repeat step to .
Selecting a preset station
Press [TUNE MODE] to select “PRESET”.
u /t ] or [y /i ] to select the
channel.
Alternatively, press the numeric buttons to
select the channel.
•
RDS broadcast
Enables
station
signal
Automatic presetting
“LOWEST” and “CURRENT” frequency.
Press [AUTO PRESET] to start presetting.
Top View
6 31
1 7 22 29 18
30
Refer to the numbers in parentheses for section reference.
28
27
26
25
24
23
22
21
20
2
18
17
16
15
14
3
1
4
5
6
7
8
9
10
11
12
13
19
Front View
Display
T
Approx.
Approx.
32
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Remote control
Main unit
MP3:
Press [e ,r ] to select the album.
y/ i ] once and then the
numeric buttons to select the track.
To program more tracks, repeat step
to .
Press q /h ] to start play.
Click!
P
Press [USB q/ h].
again
Skip
Press [u/ t ] [y/ i ].
Skip
Press [e ,r ].
Direct
play
with
you
Press [e ,r ] to select the
album.
Press [y /i] once and
then the numeric buttons
to select the track.
6
Timer
Change
or
Press [z , PLAY] twice
to clear z PLAY indicator
from the display.
Make changes to the
source or volume.
Perform step and
(➡ left).
Check
(When
on
mode)
Press [CLOCK/TIMER]
repeatedly
“z PLAz PLA
“z PLA
Cancel
Press [z ,
to
from
The timer will start at the preset time, with the
volume increasing gradually to the preset level.
•
Y
wak
This
Preparation:
Turn the unit on and set the clock (➡ above).
Prepare the music source (disc, radio, USB or
AUX) and set the volume.
•
•
Play timer
The
Press [SLEEP] to turn the sleep function on or
off.
Press [SLEEP] once to check the remaining
time.
The play timer and sleep timer can be used
together. The sleep timer always has the priority.
Be sure not to overlap the timer settings.
When AUTO OFF is ON and the unit is left
unused for about 30 minutes, the unit will shut
down even if the play time or sleep time has not
expired.
•
•
Sleep timer
OFF (Cancelled)
This
Press [CLOCK/TIMER] to select “CLOCK”.
Within 5 seconds, press [e ,r ] to set the
time. (Press and hold to change the time
faster.)
Press [OK].
To display the clock, press [CLOCK/TIMER] .
Reset the clock regularly to maintain accuracy.
•
•
Setting the clock
Press [CLOCK/TIMER] repeatedly to select
play timer.
Within 5 seconds, press [e ,r ] to set the
starting time.
Press [OK].
To set the finishing time, repeat step and
.
To activate the timer
Press [z , PLAY] repeatedly to turn the
selected play timer on.
Press [^ ] to turn the unit off.
Change
settings
Repeat
(➡ above).
5
Radio operations (continued)
AM allocation setting
The
in
To change the step to 10 kHz (by main unit
only)
Press [FM/AM/AUX] to select “AM”.
Press and hold [FM/AM/AUX].
After a few seconds the display changes to
display current minimum frequency.
Continue to hold down [FM/AM/AUX].
When the minimum frequency changes, release
the button.
To return to the original step, repeat step to
(➡ left).
After the setting is changed, any previously
preset frequency will be cleared.
•
•
g Notes on speakers
These speakers do not have magnetic shielding. Do not place them near televisions,
personal computers or other devices easily influenced by magnetism.
The speaker nets cannot be removed.
•
•
Connections
1
Tape the antenna to a wall or
column, in a position with the
least amount of interference.
•
FM
Connect the FM indoor antenna.
Adhesive
1
Connect the AM loop antenna.
Stand
its
AM loop antenna
2
Click!
Keep the loose antenna cord away from other wires and cords.
Connect the AC mains lead after all other connections are complete.
Connect the AC mains lead.
3
READ
LEAD
T
Ventilation holes
1
2
3
4
Use FM outdoor antenna only if the radio reception is poor.
Use the included antenna plug adapter to connect the FM outdoor antenna.
The antenna should only be installed by a competent technician.
Never use an outdoor antenna during lightning storm.
•
•
•
•
Using an outdoor antenna (optional)
Switch the equalizer off or turn the volume of the portable equipment down to reduce
the input signal. High level of input signal will distort the sound.
For details, refer to the instruction manual of the other equipment.
Cords and equipment are not included.
•
•
•
You can select the sound input level of the portable audio equipment.
Press [INPUT LEVEL] repeatedly to select “HIGH” or “NORMAL”.
Avoid listening for prolonged periods of time to prevent hearing damage.
Excessive sound pressure from earphones and headphones can cause hearing loss.
•
•
Reduce
Plug
Headphones (not included)
4
Plug the audio cord into the AUX jack.
Plug type: 3.5 mm stereo
Press [AUX] and start playback from the portable audio source.
5
Portable audio equipment (during AUX mode)
Back View
SC-HC10_EN (EB) 12.01.10.indd 2 12/01/2010 11:35:34
