608305
8
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
RQT7806
8
ENGLISH
ESPAÑOL
Connect to a receiver or amplifier
m
with 6- impedance for the
front, center, surround and surround back speakers.
Before connection
Turn off the other equipment.
Do not connect the AC mains lead until all other cables and cords
are connected.
Twist off the tip of the cable to a length of approximately 15 mm.
Connect the front
A
,
C
and center speakers
B
with the
short cables
n
(not included) and the surround
D
,
E
,
surround back
G
speakers with the long cables
o
(not
included).
Be sure to connect only positive cables
q
to positive (+)
terminals and negative cables
r
to negative (–) terminals.
Connection to the SB-PF800
To enjoy an enhanced sound experience, we recommend
connecting positive cables to the positive (+) HF terminal and
negative cables to the negative (–) LF terminal.
• Do not remove the shorting bars
p
.
If using a commercially-available 4-mm plug cable
s
.
Fully tighten the speaker terminal knob, and then insert the end
of the plug cable into the top of the knob.
CAUTION
Never short-circuit positive (+) and negative (–) speaker cables.
• Do not move the speaker while the speaker cables are
connected. This may cause a short circuit.
• Make sure to bundle the speaker cable with a string etc. when
relocating the speaker cables.
Bi-wiring connection (SB-PF800)
The speakers have independent HF (mid-to-high frequency) and
LF (low frequency) terminals. Bi-wiring is possible if your amplifier
also has two sets of speaker terminals [(A) and (B)]. You can
thus enjoy an enhanced sound experience with greater presence
and spread.
• Remove the shorting bars
p
before connecting the speaker
cables and store them securely.
• The amplifier’s speaker switch allows output from both A and
B terminals. (Consult the amplifier’s operating instructions for
further information.)
t
Speaker cables (not included)
Connections
YP
B
P
R
YP
B
P
R
TV IN
DVD IN
COMPONENT VIDEO
SURROUND
SPEAKERS (6
16
)
AC IN
R L
BACK
HDMI
(DVD) IN
FRONT B
CENTER
FRONT A
R L R L
BI-WIREHF LF
SB-PF800
SB-PC800
SB-PS800
SB-PS800
SB-PS800A
m
n
o
p
SB-PF800
q
r
Protection circuitry
These units incorporate protection circuitry to protect them from
damage caused by excessive input or abnormal signals; when
excess input is detected, input is automatically interrupted.
If sound is interrupted...
1. Reduce the volume of the receiver (or amplifier).
2. Check the sound source and connections for any problems.
If there is no problem, the protection circuitry will reset in a
few minutes.
After the protection circuit is reset...
Take care not to increase the receiver’s volume too high.
Conecte un receptor o amplificador
m
con una impedancia de 6- a los
altavoces delanteros, central, ambientales y ambiental trasero.
Antes de hacer la conexión
Apague el otro equipo.
No conecte el cable de alimentación de CA hasta después de haber
conectado todos los demás cables.
Retuerza unos 15 mm aproximadamente de la punta del cable.
Conecte los altavoces delanteros
A
y
C
y el altavoz central
B
con los cables cortos
n
(no incluidos), y luego conecte
los altavoces ambientales
D
y
E
y el altavoz ambiental
trasero
G
con los cables largos
o
(no incluidos).
Asegúrese de conectar solamente los cables positivos
q
a los
terminales positivos (+) y los cables negativos
r
a los terminales
negativos (–).
Conexión al SB-PF800
Para disfrutar de un sonido mejorado recomendamos conectar los cables positivos
al terminal HF positivo (+) y los cables negativos al terminal LF negativo (–).
No quite las barras de cortocircuito
p
.
Si se utiliza un cable con clavija de 4 mm
s
de venta
en el comercio.
Apriete a fondo la perilla del terminal del altavoz, y luego inserte el extremo
del cable con clavija en la parte superior de la perilla.
No cortocircuite nunca los cables positivos (+) y negativos
(–) de los altavoces.
No mueva el altavoz mientras están conectados sus cables. Esto podría
causar un cortocircuito.
Asegúrese de juntar los cables de los altavoces con una cuerda, etc.
cuando cambie la posición de los mismos.
Conexión tipo bicableado (SB-PF800)
Los altavoces tienen terminales independientes HF (frecuencia media a
alta) y LF (frecuencia baja). El bicableado es posible si su amplificador
también tiene dos juegos de terminales de altavoces [(A) y (B)]. Usted
podrá disfrutar por lo tanto de un sonido mejorado con mayor efecto de
presencia y amplitud.
• Quite las barras de cortocircuito
p
antes de conectar los cables de
los altavoces y guárdelas en un lugar seguro.
El conmutador de altavoces del amplificador permite elegir la salida por
los terminales A y B. (Consulte las instrucciones de funcionamiento del
amplificador para conocer más información.)
t
Cables de altavoces (no incluidos)
Conexiones
Circuitería de protección
Estos aparatos incorporan una circuitería de protección para protegerlos
de daños causados por una entrada excesiva o señales anormales;
cuando una entrada excesiva es detectada, la entrada es
automáticamente interrumpida.
Si el sonido se interrumpe...
1. Reduzca el volumen del receptor (o amplificador).
2.
Verifique si hay problemas en la fuente de sonido y las conexiones.
Si no hay problemas, la circuitería de protección se reajustará en
unos pocos minutos.
Después de que el circuito de protección sea reajustado...
Cuídese de no incrementar demasiado el volumen del receptor.
PRECAUCIÓN
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic SBAFC800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic SBAFC800 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 1,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info