598895
100
Verklein
Vergroot
Pagina terug
1/130
Pagina verder
Operating Instructions
Functional Manual
DLP™ Based Projector
Commercial Use
Thank you for purchasing a Panasonic Projector.
Before operating this product, please read the instructions carefully and save this manual
J
for future use.
Before using your projector, be sure to read “
J
Precautions with regard to safety”
(
Æ
pages 9 to 17).
TQBJ0342-2
Model No.
PT-DZ110XE
PT-DS100XE
PT-DW90XE
ENGLISH
The projection lens is sold separately.
M0710KY3031 -DW
Important Safety Notice
2
- ENGLISH
Important
Information
Important Safety Notice
Dear Panasonic Customer:
This instruction booklet provides all the necessary operating information that you might require. We hope it will
help you to get the most out of your new product, and that you will be pleased with your Panasonic DLP™ Based
projector. The serial number of your product may be found on its bottom. You should note it in the space provided
below and retain this booklet in case service is required.
Model number: PT-DZ110XE/PT-DS100XE/PT-DW90XE
Serial number:
WARNING: THIS APPARATUS MUST BE EARTHED.
WARNING: To prevent damage which may result in re or shock hazard, do not expose this appliance to rain
or moisture.
Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator
position is equal or less than 70 dB (A) according to ISO 7779.
WARNING:
1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time.
2. To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to
qualied service personnel.
3. Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong
earthingtype mains plug. This plug will only t an earthing-type mains socket. This is a safety feature. If you
are unable to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the
earthing plug.
CAUTION: To assure continued compliance, follow the attached installation instructions, which includes using
the provided power cord and shielded interface cables when connecting to computer or peripheral
device. If you use serial port to connect PC for external control of projector, you must use optional
RS-232C serial interface cable with ferrite core. Any unauthorized changes or modications to
this equipment will void the user’s authority to operate.
Pursuant to at the directive 2004/108/EC, article 9(2)
Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
EEE Yönetmeliğine Uygundur.
EEE Complies with Directive of Turkey.
Important Safety Notice
ENGLISH -
3
Important
Information
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them
to applicable collection points, in accordance with your national legislation and the Directives
2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact
your local municipality, your waste disposal service or the point of sale where you purchased the
items. Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union. If you wish to discard these items, please
contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
Environment care information for users in China
This symbol is only valid in China.
Important Safety Notice
4
- ENGLISH
Important
Information
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin power plug for your safety and convenience. A 13 amp fuse
is tted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of
13 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is retted when the fuse is replaced. If you
lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover
can be purchased from an Authorized Service Center.
If the tted moulded plug is unsuitable for the wall outlet in your home, then the fuse should be removed
and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug
is inserted into any 13 amp socket.
If a new plug is to be tted, please observe the wiring code as shown below.
If in any doubt, please consult a qualied electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this power cord are colored in accordance with the following code:
Green - and - Yellow:
Blue:
Brown:
Earth
Neutral
Live
As the colors of the wire in the power cord of this appliance may not correspond with the colored markings
identifying the terminals in your plug, proceed as follows.
The wire which is colored GREEN - AND - YELLOW must be connected to the terminal in the
plug which is marked with the letter E or by the Earth symbol
or colored GREEN or GREEN -
AND - YELLOW.
The wire which is colored BLUE must be connected to the terminal in the plug which is marked
with the letter N or colored BLACK.
The wire which is colored BROWN must be connected to the terminal in the plug which is marked
with the letter L or colored RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
ENGLISH -
5
Important
Information
PreparationGetting StartedBasic OperationSettingsMaintenanceAppendix
While the luminance is the same as
the former model, the size is reduced
to about 1/2.
Volume Approx. 120 liters : PT-D10000E
Volume Approx. 60 liters : PT-DZ110XE
The lamp replacement cycle is longer
than the existing model. (
Æ
page 111)
Approx. 2 000 hours : PT-D10000E
(When four lamps are used)
Approx. 3 000 hours : PT-DZ110XE
(two lamps LAMP POWER : [HIGH])
The standby power is much less than
the existing model.
Approx. 25 W : PT-D10000E
Approx. 0.3 W : PT-DZ110XE
(STANDBY MODE : [ECO])
Reduced in size
Lengthened lamp
replacement cycle
Reduced standby power
Quick steps
J
For details, see the corresponding pages.
1. Set up your projector.
(
Æ
page 22)
2. Attach the projection lens.
(
Æ
page 38)
3. Connect with other devices.
(
Æ
page 35)
4. Connect the power cord.
(
Æ
page 39)
5. Start projecting.
(
Æ
page 40)
6. Select the input signal.
(
Æ
page 42)
7. Adjust the image.
(
Æ
page 42)
Important Safety Notice
6
- ENGLISH
Important
Information
Preparation Getting Started Basic Operation Settings Maintenance Appendix
Contents
Be sure to read “Precautions with regard to safety”. ( pages 9 to 17)
Important Information
Important Safety Notice ............................ 2
Precautions with regard to safety ............ 9
WARNING ..............................................................9
CAUTION .............................................................12
Cautions when transporting .................................12
Cautions when installing ......................................13
Security ................................................................15
Cautions on use ...................................................15
Cleaning and maintenance ..................................16
Disposal ...............................................................16
Accessories ..........................................................17
Preparation
About Your Projector .............................. 18
Remote control .....................................................18
Projector body ......................................................19
Setting projector ID number to remote control .....21
Using a wired remote control ...............................21
Getting Started
Setting up ................................................. 22
Projection method ................................................22
Screen size and throw distance ...........................23
Front leg adjusters and throwing angle ................34
Connections ............................................. 35
Before connection to the projector .......................35
Connecting example : AV equipment ...................36
Connecting example : Computers........................37
Removing/attaching the projection lens
(optional) .............................................. 38
How to install the projection lens .........................38
How to remove the projection lens.......................38
Basic Operation
Powering ON/OFF .................................... 39
Connecting the power cord ..................................39
Powering up the projector ....................................40
Making adjustment and selection.........................40
Powering off the projector ....................................41
Direct power off function ......................................41
Projecting ................................................. 42
Selecting the input signal .....................................42
How to adjust the focus, zoom and shift ..............42
Adjustment range after lens position
(optical shift) ..................................................43
Moving the projection lens position to the home
position ..........................................................44
Lens adjustment to compensate for uneven
screen focus ..................................................44
Basic operations using the remote
control................................................... 47
Using the SHUTTER function ..............................47
On-screen display function ..................................47
Switching the input signal ....................................47
STATUS function ..................................................47
Automatic adjustment ..........................................48
Using the FUNCTION button ...............................48
Displaying the internal test pattern.......................48
Changing the picture aspect ratio ........................49
Settings
Menu Navigation ...................................... 50
Navigating through the menu ...............................50
MAIN MENU ........................................................51
SUB MENU ..........................................................51
PICTURE menu ........................................ 53
PICTURE MODE .................................................53
CONTRAST .........................................................54
BRIGHTNESS ......................................................54
COLOR ................................................................54
TINT .....................................................................54
COLOR TEMPERATURE ....................................55
GAMMA ................................................................56
SYSTEM DAYLIGHT VIEW .................................56
SHARPNESS .......................................................57
NOISE REDUCTION ...........................................57
DYNAMIC IRIS ....................................................57
SYSTEM SELECTOR ..........................................58
Important Safety Notice
ENGLISH -
7
Important
Information
PreparationGetting StartedBasic OperationSettingsMaintenanceAppendix
Contents
To display pictures complying with the sRGB
standard ........................................................58
POSITION menu ....................................... 59
SHIFT ...................................................................59
ASPECT ...............................................................59
ZOOM ..................................................................60
CLOCK PHASE ...................................................61
GEOMETRY (PT-DZ110XE/PT-DS100XE only) ..61
KEYSTONE (PT-DW90XE only) ..........................63
ADVANCED MENU ................................... 64
DIGITAL CINEMA REALITY .................................64
BLANKING ...........................................................64
INPUT RESOLUTION ..........................................65
CLAMP POSITION ..............................................65
EDGE BLENDING ...............................................65
FRAME DELAY ....................................................67
RASTER POSITION ............................................67
DISPLAY LANGUAGE menu ................... 68
Changing the display language............................68
DISPLAY OPTION menu .......................... 69
COLOR MATCHING ............................................69
LARGE SCREEN CORRECTION ........................70
SCREEN SETTING (PT-DZ110XE/PT-DS100XE only)
....70
WAVEFORM MONITOR (PT-DZ110XE only) ......71
AUTO SIGNAL .....................................................72
AUTO SETUP ......................................................72
RGB IN (Only RGB input) ....................................73
DVI-D IN ...............................................................73
HDMI IN ...............................................................74
SDI IN (PT-DZ110XE/PT-DS100XE only) ............74
ON-SCREEN DISPLAY .......................................74
BACK COLOR .....................................................75
STARTUP LOGO .................................................75
FREEZE ...............................................................75
PROJECTOR SETUP menu ..................... 76
PROJECTOR ID ..................................................76
INSTALLATION ....................................................76
HIGH ALTITUDE MODE ......................................76
COOLING CONDITION .......................................77
LAMP SELECT ....................................................77
LAMP RELAY .......................................................77
LAMP POWER .....................................................78
BRIGHTNESS CONTROL ...................................78
STANDBY MODE ................................................82
SCHEDULE .........................................................82
RS-232C ..............................................................83
STATUS ...............................................................84
NO SIGNAL SHUT-OFF ......................................85
REMOTE2 MODE ................................................85
FUNCTION BUTTON ...........................................85
DATE AND TIME ..................................................85
LENS CALIBRATION ...........................................86
FILTER COUNTER RESET .................................86
SAVE ALL USER DATA ........................................87
LOAD ALL USER DATA .......................................87
INITIALIZE ...........................................................87
SERVICE PASSWORD .......................................87
P IN P menu .............................................. 88
Using the P IN P function .....................................88
Setting the P IN P function ...................................88
TEST PATTERN menu ............................. 89
TEST PATTERN ...................................................89
SIGNAL LIST menu .................................. 90
Registering a signal to the list ..............................90
Renaming a registered data.................................90
Deleting a registered data ....................................90
Managing the sub memory list .............................91
SECURITY menu ...................................... 92
SECURITY PASSWORD .....................................92
SECURITY PASSWORD CHANGE .....................92
DISPLAY SETTING .............................................93
TEXT CHANGE ...................................................93
MENU LOCK ........................................................93
MENU LOCK PASSWORD ..................................93
CONTROL DEVICE SETUP ................................94
NETWORK menu ..................................... 95
NETWORK SETUP ..............................................95
NETWORK CONTROL ........................................95
NETWORK STATUS ............................................95
Network connections............................................96
Important Safety Notice
8
- ENGLISH
Important
Information
Preparation Getting Started Basic Operation Settings Maintenance Appendix
Contents
Accessing from the Web browser ........................97
Maintenance
Monitor Lamp indicators ....................... 108
Managing the indicated problems ......................108
Replacement ...........................................110
Before replacing the unit ....................................110
Replacing the unit ..............................................110
Troubleshooting .....................................113
Appendix
Technical Information ............................115
PJLink protocol ..................................................115
Control commands via LAN ............................... 116
Serial terminal ....................................................118
REMOTE 2 IN terminal ......................................121
Two window display combination list .................122
Restoring the MENU LOCK PASSWORD
to default......................................................122
List of compatible signals ...................................123
Specications ........................................ 125
Dimensions ........................................................127
About brand .......................................................127
Ceiling mount bracket safeguards....... 128
Attachment procedure........................................128
Index ....................................................... 129
Precautions with regard to safety
ENGLISH -
9
Important
Information
Precautions with regard to safety
WARNING
POWER
The wall outlet or the circuit breaker shall be installed near the equipment and shall be
easily accessible when problems occur. If the following problems occur, cut off the power
supply immediately.
Continued use of the projector in these conditions will result in re or electric shock.
If foreign objects or water get inside the projector, cut off the power supply.
z
If the projector is dropped or the cabinet is broken, cut off the power supply.
z
If you notice smoke, strange smells or noise coming from the projector, cut off the power supply.
z
Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.
During a thunderstorm, do not touch the projector or the cable.
Electric shocks can result.
Do not do anything that might damage the power cord or the power plug.
If the power cord is used while damaged, electric shocks, short-circuits or re will result.
Do not damage the power cord, make any modications to it, place it near any hot objects, bend it
z
excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.
Insert the power plug securely into the wall outlet.
If the plug is not inserted correctly, electric shocks or overheating will result.
Do not use anything other than the provided power cord.
z
Do not use the provided power cord for other electrical equipment.
z
Do not use plugs which are damaged or wall outlets which are coming loose from the wall.
z
Clean the power plug regularly to prevent it from becoming covered in dust.
Failure to observe this will cause a re.
If dust builds up on the power plug, the resulting humidity can damage the insulation.
z
If not using the projector for an extended period of time, pull the power plug out from the wall outlet.
z
Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.
Do not handle the power plug with wet hands.
Failure to observe this will result in electric shocks.
Do not overload the wall outlet.
If the power supply is overloaded (ex., by using too many adapters), overheating may occur and re will result.
ON USE/INSTALLATION
Do not place liquid containers on top of the projector.
If water spills onto the projector or gets inside it, re or electric shocks will result.
If any water gets inside the projector, contact an Authorized Service Center.
Do not place the projector on soft materials such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can cause burns, re or damage to the projector.
Do not set up the projector in humid or dusty places or in places where the projector may
come into contact with oily smoke or steam, ex. a bathroom.
Using the projector under such conditions will result in re, electric shocks or components deterioration.
Components deterioration (such as ceiling mount brackets) may cause the projector which is mounted on the
ceiling to fall down.
Do not install this projector in a place which is not strong enough to take the full weight of
the projector or on top of a surface which is sloped or unstable.
Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage
could result.
Precautions with regard to safety
10
- ENGLISH
Important
Information
Do not place another projector or other heavy objects on top of the projector.
Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or
injury. The projector will be damaged or deformed.
Installation work (such as ceiling suspension) should only be carried out by a qualied
technician.
If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks.
Do not use anything other than an authorized ceiling mount bracket.
z
Be sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the
z
projector from falling down. (Install in a different location to the ceiling mount bracket)
Do not cover the air inlet port or the air outlet port.
Doing so will cause the projector to overheat, which can cause re or damage to the projector.
Do not place the projector in narrow, badly ventilated places such as closets or bookshelves.
z
Do not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.
z
Do not place your hands or other objects close to the air outlet port.
Doing so will cause burns or damage your hands or other objects.
Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand
z
heat close to this port.
Do not look and place your skin into the lights emitted from the lens while the projector is
being used.
Doing so can cause burns or loss of sight.
Strong light is emitted from the projector’s lens. Do not look or place your hands directly into this light.
z
Be especially careful not to let young children look into the lens. In addition, turn off the power and disconnect
z
the power plug when you are away from the projector.
Do not insert any foreign objects into the projector.
Doing so will cause re or electric shocks.
Do not insert any metal objects or ammable objects into the projector or drop them onto the projector.
z
Never attempt to remodel or disassemble the projector.
High voltages can cause re or electric shocks.
For any inspection, adjustment and repair work, please contact an Authorized Service Center.
z
Do not project an image with the lens cover attached.
Doing so can cause re.
When replacing the lamp, do not touch the fan with your nger or another part of your
body.
If you do so, you may get hurt.
ACCESSORIES
Do not use or handle the batteries improperly, and refer to the following.
Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re.
Do not use unspecied batteries.
z
Use manganese batteries but not rechargeable batteries.
z
Do not disassemble dry cell batteries.
z
Do not heat the batteries or place them into water or re.
z
Do not allow the + and
z
-
terminals of the batteries to come into contact with metallic objects such as
necklaces or hairpins.
Do not store batteries together with metallic objects.
z
Store the batteries in a plastic bag and keep them away from metallic objects.
z
Make sure the polarities (+ and
z
-
) are correct when inserting the batteries.
Do not use a new battery together with an old battery or mix different types of batteries.
z
Do not use batteries with the outer cover peeling away or removed.
z
Remove the empty batteries from the remote control at once.
z
Insulate the battery using tape or something similar before disposal.
z
Precautions with regard to safety
ENGLISH -
11
Important
Information
Do not allow children to reach the AA/R6 batteries.
The battery can cause personal injury if swallowed.
z
If swallowed, seek medical advice immediately.
z
If the battery uid leaks, do not touch it with bare hands, and take the following measures if
necessary.
Battery uid on your skin or clothing could result in skin inammation or injury.
z
Rinse with clean water and seek medical advice immediately.
Battery uid coming in contact with your eyes could result in loss of sight.
z
In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.
Do not disassemble the lamp unit.
If the lamp breaks, it could cause injury.
Lamp replacement
The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will result.
Replacement of the lamp should be carried out by a qualied technician.
z
The lamp can easily explode if struck against hard objects or dropped.
z
Before replacing the lamp, be sure to disconnect the power plug from the wall outlet.
z
Electric shocks or explosions can result if this is not done.
When replacing the lamp, allow it to cool for at least one hour before handling it otherwise it can cause burns.
z
Do not allow infants or pets to touch the remote control unit.
Keep the remote control unit out of the reach of infants and pets after using it.
z
Keep the attached screws and plain washers away from babies and infants.
If a baby swallows a screw by accident, it may be affected badly.
z
If a baby seems to have swallowed a screw, consult the doctor immediately.
z
Precautions with regard to safety
12
- ENGLISH
Important
Information
CAUTION
POWER
When disconnecting the power cord, be sure to hold the power plug and power connector.
If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric shocks
will result.
When not using the projector for an extended period of time, disconnect the power plug
from the wall outlet and remove the batteries from the remote control.
Disconnect the power plug from the wall outlet before carrying out any cleaning.
Electric shocks can result if this is not done.
ON USE/INSTALLATION
Do not put your weight on this projector.
You could fall or the projector could break, and injury will result.
Be especially careful not to let young children stand or sit on the projector.
z
Do not place the projector in extremely hot locations.
Doing so will cause the outer casing or internal components to deteriorate, or result in re.
Take particular care in locations exposed to direct sunlight or near stoves.
z
Always disconnect all cables before moving the projector.
Moving the projector with cables still attached can damage the cables, which will cause re or electric shocks to
occur.
Do not place your hands in the openings beside the optical lens, while shifting the lens.
Failure to observe this could cause injury.
ACCESSORIES
Do not use the old lamp unit.
If used it could cause lamp explosion.
If the lamp has broken, ventilate the room immediately. Do not touch or bring your face
close to the broken pieces.
Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and which
contains nearly the same amount of mercury as uorescent lamps, and the broken pieces will cause injury.
If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical
z
advice immediately.
Ask your dealer about replacing the lamp unit and check the inside of the projector.
z
Cautions when transporting
When transporting the projector or carrying it around, make sure that the lens cover is always in place, and
remove the lens. Please take care to keep them away from vibration and impacts, both the projector and the lens
are precision-made and easily susceptible to damage.
When transporting the projector, the leg adjusters must be housed and do not hold them. Please securely hold
only its bottom and none of its other parts or surfaces as this will result in malfunctions.
Precautions with regard to safety
ENGLISH -
13
Important
Information
Cautions when installing
After removing the projection lens, install the dust sponge attached to the
projector.
If the dust sponge is not installed, dust will be accumulated inside and can cause a trouble.
Do not use under the following conditions.
Do not set up the projector outdoors.
z
The projector is designed for indoor use only.
Avoid setting up in places which are subject to vibration or shocks.
z
If the projector is installed in a place where vibrations are transmitted or mounted in a car or a vessel,
vibrations or impacts will result in damage to the internal parts, causing failure. Install the product in a place
free from vibrations and impacts.
Avoid setting up in places which are subject to sudden temperature changes, such as near an air
z
conditioner or lighting equipment.
Failure to observe this will result in malfunctions or the lamp life will be shortened.
See “
TEMP indicator” on page 109.
Avoid setting up in places which are near high-voltage power lines or near motors.
z
The product will be exposed to interference if it is installed in the vicinity of high-voltage electrical power lines
or power sources.
Do not install the projector at elevations higher than 2 700 m (8 858 ft) above sea level.
z
If using this projector at high elevations 1 400 - 2 700 m (4 593 - 8 858 ft) above sea level, set [HIGH
ALTITUDE MODE] to [ON].
If using this projector at elevations lower than 1 400 m (4 593 ft) above sea level, set [HIGH ALTITUDE
MODE] to [OFF].
Failure to observe this will result in malfunctions or the lamp life or life of other components will be shortened.
When installing and using the projector at an angle that exceeds 30° vertically, set [COOLING
z
CONDITION].
Failure to observe this will result in malfunctions or the lamp life or other components will be shortened.
Lens Focus
Do not adjust the lens focus in the initial period after switching the projector on. The high clarity projector lens is
thermally affected by the light from the light source, making the focus unstable in the period just after switching
on. Please allow a warm-up time of at least 30 minutes before adjusting the lens focus.
Be sure to ask a specialized technician when installing the product to a
ceiling.
If the product is to be installed hanging from the ceiling, purchase an optional Ceiling Mount Attachment (For high
ceilings: Model No. ET-PKD310H, For low ceilings: Model No. ET-PKD310S). Please call a specialized technician
or contact an Authorized Service Center for installation.
Precautions with regard to safety
14
- ENGLISH
Important
Information
Cautions when setting the projectors 1
When installing and using the projector with a method other than oor standing installing using adjustable
z
feet, x it with the 5 ceiling mounting screws (shown in the gure).
(Screw diameter: M6, Tapping depth inside set: 8 mm)
Make a clearance of at least 5 mm between the projector bottom and setting surface by inserting spacers
z
(metallic) etc. between them.
The adjustable feet can be removed if they are not necessary for installation. However, do not use the screw
z
holes for them to x the projector.
Do not tighten other screws etc. into the screw holes for the adjustable feet.
Doing so can break the set.
When installing the removed adjustable feet again, note that the front and rear ones have different lengths.
(The longer screws are used for front feet. Length of front leg screw: 65 mm, Length of rear leg screw:
23 mm)
When installing the projector with a method other than oor standing installing, do not adjust its angle with the
z
adjustable feet. Doing so can break the set.
Ceiling mounting screws (M6)
Gap (Min. 5 mm)
Make sure air can circulate
around the air intake vent.
Failure to do so may result
in the projector not operating
properly.
Spacers
Base
Precautions with regard to safety
ENGLISH -
15
Important
Information
Cautions when setting the projectors 2
When placing the projector in conned space, a ventilation or air conditioning system must be equipped, and
z
keep enough ventilation space on the rear and both sides of the projector.
Make a clearance of at least 5 mm between the projector bottom and setting surface by inserting spacers
z
(metallic) etc. between them.
z
Do not stack the projectors without using frame or shelf.
Do not cover the ventilation openings or place anything within 50 cm (20") of them
z
as this may cause damage or injury.
Avoid heating or cooling air of the air conditioning systems directly blow on to the
z
projector ventilation openings.
You can tilt the projector within ± 15 degrees horizontally.
z
Security
Take safety measures against following incidents.
Personal information being leaked via this product.
z
Unauthorized operation of this product by a malicious third party.
z
Interfering or stopping of this product by a malicious third party.
z
Security instruction
The connecting network must be secured by rewall or others.
z
Change your password regularly.
z
Do not use a password that is simple to guess.
z
Panasonic and its afliate companies would never directly inquire about your password.
z
Do not share your password with the general public.
z
Set a password, and place restrictions on the users who can log in.
z
Cautions on use
In order to get the picture quality
Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light
z
from indoor lamps from shining onto the screen.
Depending on where the projector is used, air exhaust vents or the warm air from air conditioning can cause
z
a shimmering effect on the screen. For this reason, take care not to shield the air exhaust vents and consider
the direction of the air owing from air conditioning.
over 50 cm (20")
over 10 cm (4")
over 50 cm (20") over 50 cm (20")
-
15°
+15°
Precautions with regard to safety
16
- ENGLISH
Important
Information
Do not touch the surface of the projector lens with your bare hand.
If the surface of the lens becomes dirty from ngerprints or anything else, this will be magnied and projected
onto the screen. Please put the lens cover on the projector when you do not use it.
Do not move the projector while it is operating or subject it to vibration or
impact.
The service life of its internal components will be shortened.
The projector has a high pressure mercury lamp that is characterized as
follows:
The brightness of the lamp will decrease over time.
z
The lamp may explode or shorten the lamp life by shocks or chipping damage.
z
In rare cases, it may burst shortly after the rst use.
z
The possibility of its bursting increases when the lamp is used beyond the replacement time.
z
If the lamp bursts, gas inside the lamp is released in the form of smoke.
z
The life of a mercury lamp varies according to the individual difference or conditions of use.
z
In particular, turning the power on and off frequently and/or repeatedly as well as continuous use for 22 hours
z
will greatly affect the life cycle. Provide a lamp for replacement in advance.
Lamp deterioration accelerates when used continuously for 22 hours or more. Lamp deterioration due to
z
continuous use can be reduced by using the “LAMP RELAY” function.
Connection to external device
When connecting the projector to a computer or external device, use the power cord supplied with the
corresponding device and a commercially available shielded interface cable.
Optical components
It may be necessary to replace the optical components such as DLP chips and Polarizing plates in less than 1
year if using the projector in a high temperature environment or in a very dusty, oily smoke or tobacco smoke
environment. For more details, please contact your dealer.
DLP chips
The DLP chips are precision-made. Note that in rare cases, pixels of high precision could be missing or always lit,
but this is not a malfunction. Please take note that directing a laser beam onto the lens surface can damage the
DMD element.
Cleaning and maintenance
Ask an Authorized Service Center to clean the inside of the projector at
least once a year.
If dust is left to build up inside the projector without being cleaned out, it can result in re or problems with
operation. It is a good idea to clean the inside of the projector before the season when humid weather arrives.
Ask your nearest Authorized Service Center to clean the projector when required.
Please discuss with the Authorized Service Center regarding cleaning costs.
Be sure to remove the power plug from the wall outlet before cleaning.
z
Use soft and dry cloth to clean the cabinet.
z
Use a soft cloth moistened in warm water to clean away oil. Do not use solvents such as benzene, thinner,
and alcohol, detergents for kitchens, or a chemical cloth. If using such solvents, the outer case will become
deformed, and the paint may peel off.
Do not clean the lens surface with fuzzy or dusty cloths.
z
If dust adheres to the lens, it will be magnied and projected on the screen. Use a soft and clean cloth to wipe
off dust.
Disposal
When discarding this product, please contact your local authorities or dealer and ask for the correct method of
disposal.
Precautions with regard to safety
ENGLISH -
17
Important
Information
Accessories
Make sure the following accessories are provided with your projector.
Remote control (x1)
(N2QAYB000550)
Power cord (x1)
(TXFSX01RGRZ)
Power cord (x1)
(TXFSX02RGRZ)
Drop-prevention bracket (x2)
(TTRA0238)
Safety cables (x2)
Washers (x4)
Wire rope xing screw (x2)
CD-ROM (x1)
(TXFQB02VKN)
AA/R6 batteries for
remote control (x2)
Lens xing screw (x1)
(XYN4+J18FJ)
Attention
After unpacking the projector, discard the power cord cap and packaging material properly.
z
For lost accessories, consult your dealer.
z
The part numbers of accessories and separately sold components are subject to change without notice.
z
Store small parts in an appropriate manner, and keep them away from young children.
z
About Your Projector
18
- ENGLISH
Preparation
About Your Projector
Attention
Do not drop the remote control.
z
Avoid contact with liquids or moisture.
z
Do not attempt to modify or disassemble the remote control.
z
Do not let strong light shine onto the signal receptor. The remote control may malfunction under strong light such as
z
uorescent.
Note
The remote control can be used within a distance of about 30 m if pointed directly at the remote control receiver. The
z
remote control can control at angles of up to ± 15 °C vertically and ± 30 °C horizontally, but the effective control range may
be reduced.
If there are any obstacles between the remote control and the remote control signal receptor, the remote control may not
z
operate correctly.
The signal will be reected off the screen. The operating range may differ due to the screen material.
When the projector receives a signal from the remote control, the Power indicator will ash.
z
Remote control
J
Top view
Front view
J
Installing/removing batteries
Press the tab and
lift up the cover.
Insert the batteries according to
the polarity diagram indicated
inside. (insert the
side rst).
Remove the batteries in the
reverse order to setting.
Bottom view
J
Remote control wired terminal
(
Æ
page 21)
Remote control signal emitters
Species the ID of the remote control.
(
Æ
page 21)
Restores the default factory setting.
(
Æ
page 50)
Assign the frequently use functions
from options for shortcut.
(
Æ
page 48)
These buttons are used together with
▲▼◄► to adjust focus, zoom and
shift by the projection lens.
(
Æ
pages 40, 42)
Switches the image aspect ratio.
(
Æ
page 49)
Pressing this button toggles the
projector’s internal mechanical shutter
to black out the projector.
(
Æ
page 47)
Pressing this button while projecting
an image automatically corrects the
picture positioning on the screen.
While the auto setup feature is active,
a message “PROGRESS” appears on
the screen. (
Æ
page 48)
Returns to the standby mode.
Makes the remote control available
to control any ID projectors.
(
Æ
page 21)
Displays projector information.
Enter ID number of the remote
control and adjustment values of
menu items.
Displays the test pattern.
(
Æ
page 48)
Displays and clears the on
screen indications.
(
Æ
page 47)
<MENU> button
Displays and clears the main menu, and
returns to the previous menu when the
menu is displayed.
Navigation and <ENTER> buttons
Navigate through the menu items with
▲▼◄►, and activate them with the
<ENTER> button. (
Æ
page 50)
These buttons select the RGB1,
RGB2, DVI-D, VIDEO, S-VIDEO
and SDI terminals. (
Æ
page 47)
Starts the projection while in the
standby mode.
Remote control indicator
Flashes by pressing any
buttons.
About Your Projector
ENGLISH -
19
Preparation
Projector body
J
Front view
Side views
J
Û
: Attach a commercial burglar prevention cable.
Burglar hook port
Û
Auto Cleaning
Filter (ACF)
compartment
(
Æ
page 110)
Remote control
signal receptor
Air exhaust port
Air intake port
Air intake port
Air intake port
Lamp unit compartment
(
Æ
page 111)
Air exhaust port
Filter indicator (FILTER)
Indicates the lter status. (
Æ
page 109)
Remote control
signal receptor
Temperature indicator (TEMP)
Indicates the temperature status. (
Æ
page 109)
Front leg adjusters
Screw up/down to adjust
the projection angle.
Lamp2 indicator (LAMP2)
Indicates the lamp2 unit status. (
Æ
page 108)
Lamp1 indicator (LAMP1)
Indicates the lamp1 unit status. (
Æ
page 108)
Power indicator (STANDBY(R) / ON(G))
Indicates the power supply status.
Security lock
Air intake portTerminals on side
CONTROL
PANEL
AC IN terminal
Connect the power cord to supply
electronic power to the projector.
<MAIN POWER> switch
Switch the projector on/off.
J
Rear view Bottom view
J
Attention
Keep your hands and other objects away from the air outlet port.
Keep your hand and face away.
z
Keep heat-sensitive articles away.
z
Inserting your nger may result in injury.
z
Heated air from the air outlet port can cause burns or deformations.
About Your Projector
20
- ENGLISH
Preparation
CONTROL PANEL
J
Terminals on side
J
Attention
Do not touch the LAN terminal with your bare hands or body, as body parts may have charged static electricity. Failure to
z
do so may cause malfunctions.
Do not touch the metallic parts of LAN terminal and cable.
Please connect the LAN to indoor devices only.
z
VIDEO
Switches to VIDEO input.
S-VIDEO
Switches to S-VIDEO input.
RGB1
Switches to RGB1 input.
RGB2
Switches to RGB2 input.
DVI-D/HDMI
Switches to DVI-D or HDMI input.
SDI
Switches to SDI input.
(PT-DZ110XE/PT-DS100XE only)
<AUTO SETUP> button
Pressing this button while projecting an image
automatically corrects the picture positioning on
the screen. While the auto setup feature is active,
a message “PROGRESS” appears on the screen.
(
Æ
page 48)
▲▼◄► button
Use these buttons to select menu items,
change settings, adjust levels, and to enter the
[SECURITY] password.
<SHUTTER> button
Pressing this button toggles the projector’s
internal mechanical shutter to black out the
projector. (
Æ
page 47)
<ENTER> button
Press to activate a menu selection or to initiate a
function.
<LENS> button
This button is used together with ▲▼◄► to
adjust focus, zoom and shift by the projection
lens.
<MENU> button
Displays and clears the main menu, and returns to the previous
menu when the menu is displayed.
If you hold it down for at least 3 seconds while the on-screen
indication is [OFF], the [OFF] state is canceled. (
Æ
page 50)
<POWER ON> button
Starts the projection while in the
standby mode.
<STANDBY> button
Returns to the standby mode.
SDI IN
Connect an SDI signals.
(PT-DZ110XE/PT-DS100XE
only)
SERIAL IN/OUT
Connect an RS-232C cable from/to a computer.
DVI-D IN
Connect a single link DVI-D
signals.
HDMI IN
Connect a HDMI signals.
RGB2 IN
Connect an RGB or YP
B
P
R
signals.
RGB (YP
B
P
R
)1 IN
Connect an RGB or YP
B
P
R
signals.
REMOTE 2 IN
Connect a cable from an
external control circuit.
REMOTE 1 IN/OUT
When two or more main
units are used in the system,
they can be connected and
controlled with wired remote
control cable.
LAN
Connect a LAN cable for network
connection.
VIDEO IN
Connect a VIDEO signals.
S-VIDEO IN
Connect an S-VIDEO signals.
About Your Projector
ENGLISH -
21
Preparation
Setting projector ID number
to remote control
Each projector can be assigned a unique ID number,
and the handheld remote’ s number must be set to
match the intended projector.
The ID number of the projector is set to “ALL” on
shipping, and use the ID ALL button of the remote
control when using only a single projector.
Press <ID SET> button, and the 1 )
projector (s) will display it’s current ID
number onscreen. Within 5 seconds,
use the numeric keys (0-9) to match
the Remote’s ID number with that of
the desired projector.
Attention
Do not press <ID SET> button accidentally or carelessly
z
because the ID number on the remote control can be set
even when no projector is around.
If you do not enter the 2 digits ID number within 5
z
seconds after <ID SET> button has been pressed, the ID
will remain at the number that was set before <ID SET>
button was pressed.
Your specied ID number is stored in the remote control
z
unit unless another one is specied later. However, the
stored ID will be erased if the batteries of the remote
control are left exhausted. When the batteries are
replaced, set the same ID number again.
The ID number can be set to “ALL” or from “1” to “64”.
z
Note
Refer to “PROJECTOR ID” of “PROJECTOR SETUP
z
menu” (
Æ
page 76).
Using a wired remote control
When multiple projectors are connected as part of the
system, connect to units with a M3 stereo mini jack
commercial cable to simultaneously control multiple
main units with a single remote control through the
REMOTE 1 IN/OUT terminal. It is effective to use the
wired remote control in the environment in which an
obstacle stands in the light path or where devices are
susceptible to outside light.
Attention
Use 2 core shielded cable of length of 15 m or less. If the
z
length of the cable exceeds 15 m (49' 2"), the shielding
of the cable may not be sufcient and the remote control
may not work.
Remote Control
Connect to the remote
control wired terminal
Connect to the
secondary projector
M3 stereo mini jack cable
(commercial)
Connection terminals
Setting up
22
- ENGLISH
Getting Started
Setting up
Projection method
You can use the projector with any of the following 4 projection methods. To set the desired method in the
projector.
Mounting on the ceiling and
J
projecting from front
Setting on a desk/oor and
J
projecting from rear
(Using translucent screen)
Menu
Û
Method
INSTALLATION FRONT/CEILING
COOLING
CONDITION
CEILING SETTING
Menu
Û
Method
INSTALLATION REAR/FLOOR
COOLING
CONDITION
FLOOR SETTING
Mounting on the ceiling and
J
projecting from rear
(Using translucent screen)
Setting on a desk/oor and
J
projecting from front
Menu
Û
Method
INSTALLATION REAR/CEILING
COOLING
CONDITION
CEILING SETTING
Menu
Û
Method
INSTALLATION FRONT/FLOOR
COOLING
CONDITION
FLOOR SETTING
Refer to “INSTALLATION” of “PROJECTOR SETUP menu:
Û
and “COOLING CONDITION” (
Æ
pages 76, 77) for
details.
Setting up
ENGLISH -
23
Getting Started
Screen size and throw distance
When planning the projector and screen geometry, refer to the gures below and the information on the following
pages for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be
nely adjusted with the powered zoom lens and lens shifting mechanism.
L (LW/LT)
Û
Projection distance (m)
SH Height of the projection area (m)
SW Width of the projection area (m)
H
Vertical distance between the lens center level and the
bottom edge of the projected image. (m)
SD Diagonal length of the projection area (m)
LW : Minimum distance:
Û
LT : Maximum distance
Attention
Before installing, please read
z
“Precautions with regard to safety” (
Æ
pages 9 to 17)
Special care should be used when DLP projectors are used in the same room as high power laser equipment.
z
Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices ™ in which case
there is a loss of warranty.
L (LW/LT)
Screen
L (LW/LT)
SW
Screen
H
SH
SW
SD
Projected image
SH
Setting up
24
- ENGLISH
Getting Started
Projected range using geometric adjustment
J
(PT-DZ110XE/PT-DS100XE only)
VERTICAL KEYSTONE (Side View) HORIZONTAL KEYSTONE (Top View)
VERTICAL ARC (Side View) HORIZONTAL ARC (Top View)
Lens
Keystone correction only When using arc and keystone correction together
Arc correction only
Vertical
Keystone
Correction
Angle α (°)
Horizontal
Keystone
Correction
Angle β (°)
Vertical
Keystone
Correction
Angle α (°)
Horizontal
Keystone
Correction
Angle β (°)
R2/L2
minimum
value
R3/L3
minimum
value
R2/L2
minimum
value
R3/L3 minimum value
DS100XE DZ110XE
ET-D75LE1 ±40 ±15 ±5 ±5 1.6 3.2 0.8 1.6
ET-D75LE2 ±40 ±15 ±5 ±5 1.2 2.4 0.6 1.2
ET-D75LE3 ±40 ±15 ±10 ±10 0.8 1.6 0.4 0.8
ET-D75LE4 ±40 ±15 ±10 ±15 0.6 1.0 0.3 0.5
ET-D75LE5 ±22 ±15 ±5 ±5 3.0 6.0 1.5 3.0 4.3
ET-D75LE6 ±28 ±10 ±5 ±5 2.4 4.8 1.2 2.4 2.6
ET-D75LE8 ±40 ±15 ±10 ±15 0.4 0.8 0.2 0.4
ET-D75LE10 ±40 ±15 ±5 ±5 1.6 3.2 0.8 1.6
ET-D75LE20 ±40 ±15 ±5 ±5 1.6 3.2 0.8 1.6
ET-D75LE30 ±40 ±15 ±5 ±5 1.2 2.4 0.6 1.2
Note
When using geometric adjustment, if the amount of compensation is too great, excessive blurring may result.
z
The curved screens illustrated are simply sections of a full circle.
z
Screen Screen
L2
Screen
R2
L2 : Projection distance
R2 : Radius of the circle
L2
Screen
R2
L2 : Projection distance
R2 : Radius of the circle
Center of
the circle
R3
Screen
L3
L3 : Projection distance
R3 : Radius of the circle
Center of
the circle
R3
Screen
L3
L3 : Projection distance
R3 : Radius of the circle
Setting up
ENGLISH -
25
Getting Started
Projection distance by projection lens (for PT-DZ110XE)
J
For the screen aspect ratio of 16 : 10 (Unit : m)
Q
Lens type Zoom lens
Model number of
projection lens
ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8
Throw ratio
Û
1.4–1.8 : 1 1.8–2.8 : 1 2.8–4.6 : 1 4.6–7.4 : 1 7.3–13.8 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
1.78 (70") 0.942 1.508 2.01 2.69 2.72 4.10 4.11 6.90 6.91 11.06 10.78 20.56
2.03 (80") 1.077 1.723 2.31 3.09 3.12 4.70 4.71 7.90 7.91 12.66 12.37 23.55
2.29 (90") 1.212 1.939 2.61 3.49 3.52 5.30 5.31 8.91 8.91 14.25 13.97 26.54
2.54 (100") 1.346 2.154 2.91 3.89 3.92 5.90 5.91 9.91 9.91 15.85 15.57 29.53
3.05 (120") 1.615 2.585 3.51 4.68 4.73 7.10 7.11 11.91 11.92 19.04 18.76 35.50
3.81 (150") 2.019 3.231 4.40 5.88 5.93 8.90 8.91 14.92 14.93 23.82 23.54 44.47
5.08 (200") 2.692 4.308 5.89 7.87 7.93 11.91 11.92 19.94 19.95 31.80 31.52 59.41
6.35 (250") 3.365 5.385 7.39 9.87 9.93 14.91 14.92 24.95 24.96 39.77 39.49 74.36
7.62 (300") 4.039 6.462 8.88 11.86 11.93 17.91 17.92 29.97 29.98 47.75 47.47 89.30
8.89 (350") 4.712 7.539 10.37 13.86 13.93 20.91 20.92 34.98 34.99 55.72 55.44 104.24
10.16 (400") 5.385 8.616 11.86 15.85 15.94 23.92 23.93 40.00 40.01 63.70 63.42 119.19
12.7 (500") 6.731 10.770 14.85 19.84 19.94 29.92 29.93 50.03 50.04 79.65 79.37 149.08
15.24 (600") 8.077 12.923 17.83 23.82 23.94 35.93 35.94 60.06 60.07 95.60 95.32 178.96
Lens type Zoom lens Fixed-focus lens
Model number of
projection lens
ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5
Throw ratio
Û
0.9–1.1 : 1 1.3–1.7 : 1 1.7–2.4 : 1 2.4–4.7 : 1 0.7 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Fixed
1.78 (70") 0.942 1.508 1.35 1.62 1.90 2.46 2.46 3.58 3.56 6.94 0.99
2.03 (80") 1.077 1.723 1.55 1.86 2.19 2.83 2.82 4.11 4.08 7.96 1.15
2.29 (90") 1.212 1.939 1.76 2.10 2.47 3.20 3.19 4.64 4.61 8.98 1.30
2.54 (100") 1.346 2.154 1.96 2.34 2.76 3.56 3.55 5.17 5.13 9.99 1.45
3.05 (120") 1.615 2.585 2.36 2.82 3.32 4.30 4.28 6.22 6.18 12.03 1.76
3.81 (150") 2.019 3.231 2.96 3.55 4.18 5.40 5.37 7.81 7.75 15.08 2.22
5.08 (200") 2.692 4.308 3.97 4.75 5.60 7.24 7.19 10.45 10.38 20.16 2.99
6.35 (250") 3.365 5.385 4.98 5.96 7.02 9.07 9.00 13.09 13.00 25.25 3.76
7.62 (300") 4.039 6.462 5.99 7.17 8.44 10.91 10.82 15.73 15.62 30.34 4.53
8.89 (350") 4.712 7.539 6.99 8.37 9.86 12.74 12.64 18.37 18.24 35.42
10.16 (400") 5.385 8.616 8.00 9.58 11.28 14.58 14.46 21.01 20.86 40.51
12.7 (500") 6.731 10.770 10.01 11.99 14.12 18.25 18.09 26.29 26.11 50.68
15.24 (600") 8.077 12.923 12.03 14.40 16.96 21.92 21.73 31.58 31.35 60.85
The throw ratio is based on the value during projection onto a 3 810-mm (150") screen size.:
Û
Note
The projection distances listed here involve an error of ±5 %.
z
When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied
z
size.
Setting up
26
- ENGLISH
Getting Started
For the screen aspect ratio of 16 : 9 (Unit : m)
Q
Lens type Zoom lens
Model number of
projection lens
ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8
Throw ratio
Û
1.4–1.8 : 1 1.8–2.8 : 1 2.8–4.6 : 1 4.6–7.4 : 1 7.3–13.8 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
1.78 (70") 0.872 1.550 2.07 2.77 2.80 4.21 4.23 7.09 7.10 11.37 11.09 21.14
2.03 (80") 0.996 1.771 2.38 3.18 3.21 4.83 4.84 8.13 8.13 13.01 12.73 24.21
2.29 (90") 1.121 1.992 2.68 3.59 3.62 5.45 5.46 9.16 9.16 14.65 14.37 27.29
2.54 (100") 1.245 2.214 2.99 4.00 4.04 6.07 6.08 10.19 10.19 16.29 16.01 30.36
3.05 (120") 1.494 2.657 3.60 4.82 4.86 7.30 7.31 12.25 12.26 19.57 19.29 36.50
3.81 (150") 1.868 3.321 4.53 6.05 6.09 9.15 9.16 15.34 15.35 24.49 24.21 45.72
5.08 (200") 2.491 4.428 6.06 8.10 8.15 12.24 12.25 20.50 20.50 32.69 32.40 61.08
6.35 (250") 3.113 5.535 7.59 10.15 10.21 15.33 15.34 25.65 25.66 40.88 40.60 76.44
7.62 (300") 3.736 6.641 9.13 12.19 12.27 18.41 18.42 30.81 30.81 49.08 48.80 91.79
8.89 (350") 4.358 7.748 10.66 14.24 14.32 21.50 21.51 35.96 35.97 57.28 57.00 107.15
10.16 (400") 4.981 8.855 12.19 16.29 16.38 24.58 24.60 41.12 41.12 65.47 65.19 122.51
12.7 (500") 6.226 11.069 15.26 20.39 20.50 30.76 30.77 51.42 51.43 81.87 81.59 153.23
15.24 (600") 7.472 13.283 18.33 24.49 24.61 36.93 36.94 61.73 61.74 98.26 97.98 183.95
Lens type Zoom lens Fixed-focus lens
Model number of
projection lens
ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5
Throw ratio
Û
0.9–1.1 : 1 1.3–1.7 : 1 1.7–2.4 : 1 2.4–4.7 : 1 0.7 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Fixed
1.78 (70") 0.872 1.550 1.39 1.66 1.96 2.53 2.53 3.68 3.66 7.14 1.02
2.03 (80") 0.996 1.771 1.60 1.91 2.25 2.91 2.91 4.23 4.20 8.19 1.18
2.29 (90") 1.121 1.992 1.81 2.16 2.54 3.29 3.28 4.77 4.74 9.23 1.34
2.54 (100") 1.245 2.214 2.01 2.41 2.83 3.67 3.65 5.31 5.28 10.28 1.50
3.05 (120") 1.494 2.657 2.43 2.90 3.42 4.42 4.40 6.40 6.35 12.37 1.81
3.81 (150") 1.868 3.321 3.05 3.65 4.29 5.55 5.52 8.03 7.97 15.50 2.29
5.08 (200") 2.491 4.428 4.08 4.89 5.75 7.44 7.39 10.74 10.67 20.73 3.08
6.35 (250") 3.113 5.535 5.12 6.13 7.21 9.33 9.26 13.46 13.36 25.96 3.87
7.62 (300") 3.736 6.641 6.15 7.37 8.67 11.21 11.13 16.17 16.06 31.18 4.66
8.89 (350") 4.358 7.748 7.19 8.61 10.13 13.10 12.99 18.88 18.75 36.41
10.16 (400") 4.981 8.855 8.22 9.85 11.59 14.99 14.86 21.60 21.45 41.64
12.7 (500") 6.226 11.069 10.29 12.33 14.51 18.76 18.60 27.03 26.84 52.09
15.24 (600") 7.472 13.283 12.36 14.81 17.44 22.54 22.33 32.46 32.23 62.54
The throw ratio is based on the value during projection onto a 3 810-mm (150") screen size.:
Û
Note
The projection distances listed here involve an error of ±5 %.
z
When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied
z
size.
Setting up
ENGLISH -
27
Getting Started
For the screen aspect ratio of 4 : 3 (Unit : m)
Q
Lens type Zoom lens
Model number of
projection lens
ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8
Throw ratio
Û
1.6–2.2 : 1 2.2–3.3 : 1 3.3–5.6 : 1 5.6–8.9 : 1 8.8–16.5 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
1.78 (70") 1.067 1.422 2.29 3.06 3.09 4.65 4.66 7.83 7.83 12.54 12.25 23.32
2.03 (80") 1.219 1.626 2.63 3.51 3.55 5.33 5.34 8.96 8.97 14.34 14.06 26.71
2.29 (90") 1.372 1.829 2.96 3.96 4.00 6.01 6.02 10.10 10.10 16.15 15.87 30.09
2.54 (100") 1.524 2.032 3.30 4.41 4.45 6.69 6.70 11.23 11.24 17.96 17.67 33.47
3.05 (120") 1.829 2.438 3.98 5.32 5.36 8.05 8.06 13.50 13.51 21.57 21.28 40.24
3.81 (150") 2.286 3.048 4.99 6.67 6.72 10.09 10.10 16.91 16.92 26.98 26.70 50.39
5.08 (200") 3.048 4.064 6.68 8.93 8.99 13.49 13.50 22.59 22.59 36.01 35.73 67.31
6.35 (250") 3.810 5.080 8.37 11.18 11.25 16.89 16.90 28.27 28.27 45.04 44.76 84.23
7.62 (300") 4.572 6.096 10.06 13.44 13.52 20.29 20.30 33.94 33.95 54.07 53.79 101.14
8.89 (350") 5.334 7.112 11.75 15.70 15.79 23.69 23.70 39.62 39.63 63.10 62.82 118.06
10.16 (400") 6.096 8.128 13.44 17.96 18.05 27.09 27.10 45.30 45.31 72.13 71.85 134.98
12.7 (500") 7.620 10.160 16.82 22.47 22.58 33.89 33.90 56.65 56.66 90.18 89.91 168.81
15.24 (600") 9.144 12.192 20.20 26.98 27.12 40.69 40.70 68.01 68.02 108.24 107.96 202.65
Lens type Zoom lens Fixed-focus lens
Model number of
projection lens
ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5
Throw ratio
Û
1.1–1.3 : 1 1.6–2.0 : 1 2.0–2.9 : 1 2.9–5.6 : 1 0.8 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Fixed
1.78 (70") 1.067 1.422 1.54 1.84 2.17 2.80 2.80 4.07 4.04 7.88 1.13
2.03 (80") 1.219 1.626 1.77 2.11 2.49 3.22 3.21 4.67 4.64 9.03 1.31
2.29 (90") 1.372 1.829 2.00 2.38 2.81 3.63 3.62 5.27 5.23 10.19 1.48
2.54 (100") 1.524 2.032 2.22 2.66 3.13 4.05 4.03 5.86 5.82 11.34 1.66
3.05 (120") 1.829 2.438 2.68 3.20 3.77 4.88 4.86 7.06 7.01 13.64 2.00
3.81 (150") 2.286 3.048 3.36 4.02 4.74 6.13 6.09 8.85 8.79 17.09 2.53
5.08 (200") 3.048 4.064 4.50 5.39 6.35 8.21 8.15 11.84 11.76 22.85 3.40
6.35 (250") 3.810 5.080 5.64 6.76 7.96 10.28 10.20 14.83 14.73 28.61 4.27
7.62 (300") 4.572 6.096 6.78 8.12 9.56 12.36 12.26 17.82 17.70 34.36 5.14
8.89 (350") 5.334 7.112 7.92 9.49 11.17 14.44 14.32 20.81 20.67 40.12
10.16 (400") 6.096 8.128 9.06 10.85 12.78 16.52 16.38 23.80 23.63 45.88
12.7 (500") 7.620 10.160 11.34 13.58 16.00 20.68 20.49 29.78 29.57 57.39
15.24 (600") 9.144 12.192 13.62 16.32 19.21 24.83 24.61 35.76 35.51 68.91
The throw ratio is based on the value during projection onto a 3 810-mm (150") screen size.:
Û
Note
The projection distances listed here involve an error of ±5 %.
z
When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied
z
size.
Setting up
28
- ENGLISH
Getting Started
Projection distance by projection lens (for PT-DS100XE)
J
For the screen aspect ratio of 4 : 3 (Unit : m)
Q
Lens type Zoom lens
Model number of
projection lens
ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8
Throw ratio
Û
1.5–2.0 : 1 2.0–3.0 : 1 3.0–5.0 : 1 5.0–8.0 : 1 7.9–15.0 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
1.78 (70") 1.067 1.422 2.07 2.77 2.80 4.21 4.23 7.09 7.10 11.37 11.09 21.14
2.03 (80") 1.219 1.626 2.38 3.18 3.21 4.83 4.84 8.13 8.13 13.01 12.73 24.21
2.29 (90") 1.372 1.829 2.68 3.59 3.62 5.45 5.46 9.16 9.16 14.65 14.37 27.29
2.54 (100") 1.524 2.032 2.99 4.00 4.04 6.07 6.08 10.19 10.19 16.29 16.01 30.36
3.05 (120") 1.829 2.438 3.60 4.82 4.86 7.30 7.31 12.25 12.26 19.57 19.29 36.50
3.81 (150") 2.286 3.048 4.53 6.05 6.09 9.15 9.16 15.34 15.35 24.49 24.21 45.72
5.08 (200") 3.048 4.064 6.06 8.10 8.15 12.24 12.25 20.50 20.50 32.69 32.40 61.08
6.35 (250") 3.810 5.080 7.59 10.15 10.21 15.33 15.34 25.65 25.66 40.88 40.60 76.44
7.62 (300") 4.572 6.096 9.13 12.19 12.27 18.41 18.42 30.81 30.81 49.08 48.80 91.79
8.89 (350") 5.334 7.112 10.66 14.24 14.32 21.50 21.51 35.96 35.97 57.28 57.00 107.15
10.16 (400") 6.096 8.128 12.19 16.29 16.38 24.58 24.60 41.12 41.12 65.47 65.19 122.51
12.7 (500") 7.620 10.160 15.26 20.39 20.50 30.76 30.77 51.42 51.43 81.87 81.59 153.23
15.24 (600") 9.144 12.192 18.33 24.49 24.61 36.93 36.94 61.73 61.74 98.26 97.98 183.95
Lens type Zoom lens Fixed-focus lens
Model number of
projection lens
ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5
Throw ratio
Û
1.0–1.2 : 1 1.4–1.8 : 1 1.8–2.6 : 1 2.6–5.1 : 1 0.8 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Fixed
1.78 (70") 1.067 1.422 1.39 1.66 1.95 2.52 2.52 3.66 3.64 7.10 1.02
2.03 (80") 1.219 1.626 1.60 1.91 2.24 2.89 2.89 4.20 4.17 8.13 1.18
2.29 (90") 1.372 1.829 1.81 2.16 2.53 3.27 3.26 4.74 4.71 9.17 1.34
2.54 (100") 1.524 2.032 2.01 2.41 2.82 3.64 3.63 5.28 5.24 10.21 1.50
3.05 (120") 1.829 2.438 2.43 2.90 3.40 4.39 4.37 6.36 6.31 12.29 1.81
3.81 (150") 2.286 3.048 3.05 3.65 4.27 5.52 5.49 7.98 7.92 15.41 2.29
5.08 (200") 3.048 4.064 4.08 4.89 5.72 7.39 7.34 10.67 10.60 20.60 3.08
6.35 (250") 3.810 5.080 5.12 6.13 7.17 9.27 9.20 13.37 13.28 25.79 3.87
7.62 (300") 4.572 6.096 6.15 7.37 8.62 11.14 11.06 16.07 15.96 30.99 4.66
8.89 (350") 5.334 7.112 7.19 8.61 10.07 13.02 12.91 18.77 18.63 36.18
10.16 (400") 6.096 8.128 8.22 9.85 11.52 14.90 14.77 21.46 21.31 41.38
12.7 (500") 7.620 10.160 10.29 12.33 14.42 18.65 18.48 26.86 26.67 51.77
15.24 (600") 9.144 12.192 12.36 14.81 17.33 22.40 22.19 32.25 32.03 62.15
The throw ratio is based on the value during projection onto a 3 810-mm (150") screen size.:
Û
Note
The projection distances listed here involve an error of ±5 %.
z
When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied
z
size.
Setting up
ENGLISH -
29
Getting Started
For the screen aspect ratio of 16 : 9 (Unit : m)
Q
Lens type Zoom lens
Model number of
projection lens
ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8
Throw ratio
Û
1.5–2.0 : 1 2.0–3.0 : 1 3.0–5.0 : 1 5.0–8.0 : 1 8.0–15.0 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
1.78 (70") 0.872 1.550 2.26 3.02 3.06 4.60 4.61 7.74 7.75 12.40 12.12 23.06
2.03 (80") 0.996 1.771 2.60 3.47 3.51 5.27 5.28 8.86 8.87 14.18 13.90 26.41
2.29 (90") 1.121 1.992 2.93 3.92 3.95 5.95 5.96 9.99 9.99 15.97 15.69 29.76
2.54 (100") 1.245 2.214 3.27 4.36 4.40 6.62 6.63 11.11 11.11 17.76 17.47 33.10
3.05 (120") 1.494 2.657 3.93 5.26 5.30 7.96 7.97 13.35 13.36 21.33 21.04 39.79
3.81 (150") 1.868 3.321 4.94 6.60 6.64 9.98 9.99 16.72 16.73 26.68 26.40 49.83
5.08 (200") 2.491 4.428 6.61 8.83 8.89 13.34 13.35 22.34 22.34 35.61 35.33 66.56
6.35 (250") 3.113 5.535 8.28 11.06 11.13 16.70 16.71 27.95 27.96 44.54 44.26 83.29
7.62 (300") 3.736 6.641 9.95 13.29 13.37 20.07 20.08 33.57 33.57 53.47 53.19 100.02
8.89 (350") 4.358 7.748 11.62 15.52 15.61 23.43 23.44 39.18 39.19 62.40 62.12 116.75
10.16 (400") 4.981 8.855 13.29 17.76 17.85 26.79 26.80 44.80 44.80 71.33 71.05 133.48
12.7 (500") 6.226 11.069 16.63 22.22 22.33 33.51 33.52 56.03 56.03 89.19 88.91 166.95
15.24 (600") 7.472 13.283 19.97 26.69 26.82 40.24 40.25 67.26 67.26 107.04 106.77 200.41
Lens type Zoom lens Fixed-focus lens
Model number of
projection lens
ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5
Throw ratio
Û
1.0–1.2 : 1 1.4–1.8 : 1 1.8–2.6 : 1 2.6–5.1 : 1 0.8 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Fixed
1.78 (70") 0.872 1.550 1.52 1.82 2.13 2.75 2.75 4.00 3.97 7.74 1.12
2.03 (80") 0.996 1.771 1.75 2.09 2.44 3.16 3.15 4.59 4.55 8.88 1.29
2.29 (90") 1.121 1.992 1.97 2.36 2.76 3.57 3.56 5.17 5.14 10.01 1.47
2.54 (100") 1.245 2.214 2.20 2.63 3.08 3.98 3.96 5.76 5.72 11.14 1.64
3.05 (120") 1.494 2.657 2.65 3.17 3.71 4.79 4.77 6.94 6.89 13.40 1.98
3.81 (150") 1.868 3.321 3.33 3.98 4.66 6.02 5.98 8.70 8.64 16.80 2.50
5.08 (200") 2.491 4.428 4.45 5.33 6.24 8.06 8.01 11.64 11.56 22.46 3.36
6.35 (250") 3.113 5.535 5.58 6.68 7.82 10.11 10.03 14.58 14.47 28.11 4.22
7.62 (300") 3.736 6.641 6.71 8.03 9.40 12.15 12.05 17.51 17.39 33.77 5.08
8.89 (350") 4.358 7.748 7.84 9.38 10.98 14.19 14.07 20.45 20.31 39.43
10.16 (400") 4.981 8.855 8.96 10.73 12.56 16.23 16.10 23.39 23.23 45.09
12.7 (500") 6.226 11.069 11.22 13.43 15.72 20.32 20.14 29.27 29.06 56.40
15.24 (600") 7.472 13.283 13.47 16.14 18.88 24.41 24.18 35.15 34.90 67.72
The throw ratio is based on the value during projection onto a 3 810-mm (150") screen size.:
Û
Note
The projection distances listed here involve an error of ±5 %.
z
When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied
z
size.
Setting up
30
- ENGLISH
Getting Started
Projection distance by projection lens (for PT-DW90XE)
J
For the screen aspect ratio of 16 : 9 (Unit : m)
Q
Lens type Zoom lens
Model number of
projection lens
ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8
Throw ratio
Û
1.5–2.0 : 1 2.1–3.1 : 1 3.1–5.2 : 1 5.2–8.2 : 1 8.2–15.4 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
1.78 (70") 0.872 1.550 2.32 3.10 3.14 4.72 4.73 7.94 7.94 12.71 12.43 23.65
2.03 (80") 0.996 1.771 2.66 3.56 3.60 5.41 5.42 9.09 9.09 14.54 14.26 27.08
2.29 (90") 1.121 1.992 3.01 4.02 4.06 6.10 6.11 10.24 10.25 16.37 16.09 30.51
2.54 (100") 1.245 2.214 3.35 4.48 4.52 6.79 6.80 11.39 11.40 18.21 17.92 33.94
3.05 (120") 1.494 2.657 4.03 5.39 5.44 8.17 8.18 13.69 13.70 21.87 21.58 40.80
3.81 (150") 1.868 3.321 5.06 6.76 6.81 10.23 10.24 17.15 17.15 27.36 27.08 51.09
5.08 (200") 2.491 4.428 6.77 9.05 9.11 13.68 13.69 22.90 22.91 36.51 36.23 68.25
6.35 (250") 3.113 5.535 8.49 11.34 11.41 17.13 17.14 28.66 28.67 45.67 45.39 85.40
7.62 (300") 3.736 6.641 10.20 13.63 13.71 20.57 20.58 34.42 34.42 54.82 54.54 102.55
8.89 (350") 4.358 7.748 11.91 15.92 16.00 24.02 24.03 40.17 40.18 63.97 63.70 119.70
10.16 (400") 4.981 8.855 13.63 18.21 18.30 27.47 27.48 45.93 45.93 73.13 72.85 136.85
12.7 (500") 6.226 11.069 17.05 22.78 22.90 34.36 34.37 57.44 57.45 91.43 91.16 171.16
15.24 (600") 7.472 13.283 20.48 27.36 27.49 41.25 41.26 68.95 68.96 109.74 109.47 205.46
Lens type Zoom lens Fixed-focus lens
Model number of
projection lens
ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5
Throw ratio
Û
1.0–1.2 : 1 1.4–1.9 : 1 1.8–2.7 : 1 2.7–5.2 : 1 0.8 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Fixed
1.78 (70") 0.872 1.550 1.56 1.87 2.18 2.82 2.82 4.10 4.07 7.94 1.15
2.03 (80") 0.996 1.771 1.79 2.14 2.51 3.24 3.23 4.70 4.67 9.10 1.33
2.29 (90") 1.121 1.992 2.02 2.42 2.83 3.66 3.65 5.31 5.27 10.26 1.50
2.54 (100") 1.245 2.214 2.25 2.70 3.15 4.08 4.06 5.91 5.87 11.42 1.68
3.05 (120") 1.494 2.657 2.72 3.25 3.80 4.92 4.89 7.11 7.07 13.74 2.03
3.81 (150") 1.868 3.321 3.41 4.08 4.78 6.17 6.14 8.92 8.86 17.22 2.56
5.08 (200") 2.491 4.428 4.56 5.47 6.40 8.27 8.21 11.93 11.85 23.03 3.44
6.35 (250") 3.113 5.535 5.72 6.85 8.02 10.36 10.28 14.95 14.84 28.83 4.33
7.62 (300") 3.736 6.641 6.87 8.24 9.64 12.46 12.36 17.96 17.83 34.63 5.21
8.89 (350") 4.358 7.748 8.03 9.62 11.26 14.55 14.43 20.97 20.82 40.43
10.16 (400") 4.981 8.855 9.18 11.01 12.88 16.65 16.50 23.98 23.81 46.23
12.7 (500") 6.226 11.069 11.49 13.78 16.12 20.83 20.65 30.01 29.80 57.83
15.24 (600") 7.472 13.283 13.80 16.55 19.36 25.02 24.80 36.03 35.78 69.43
The throw ratio is based on the value during projection onto a 3 810-mm (150") screen size.:
Û
Note
The projection distances listed here involve an error of ±5 %.
z
When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied
z
size.
Setting up
ENGLISH -
31
Getting Started
For the screen aspect ratio of 4 : 3 (Unit : m)
Q
Lens type Zoom lens
Model number of
projection lens
ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8
Throw ratio
Û
2.0–2.7 : 1 2.7–4.1 : 1 4.1–6.9 : 1 6.9–11.0 : 1 10.9–20.6 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
1.78 (70") 1.067 1.422 2.86 3.82 3.86 5.80 5.81 9.74 9.75 15.59 15.30 29.04
2.03 (80") 1.219 1.626 3.28 4.38 4.42 6.65 6.66 11.15 11.16 17.83 17.55 33.24
2.29 (90") 1.372 1.829 3.70 4.94 4.98 7.49 7.50 12.56 12.57 20.07 19.79 37.44
2.54 (100") 1.524 2.032 4.12 5.50 5.55 8.33 8.34 13.97 13.98 22.31 22.03 41.64
3.05 (120") 1.829 2.438 4.96 6.62 6.67 10.02 10.03 16.79 16.80 26.79 26.51 50.04
3.81 (150") 2.286 3.048 6.21 8.30 8.36 12.55 12.56 21.02 21.03 33.52 33.24 62.64
5.08 (200") 3.048 4.064 8.31 11.11 11.17 16.77 16.78 28.07 28.07 44.72 44.44 83.63
6.35 (250") 3.810 5.080 10.41 13.91 13.99 20.99 21.00 35.12 35.12 55.93 55.65 104.63
7.62 (300") 4.572 6.096 12.51 16.71 16.80 25.21 25.22 42.16 42.17 67.14 66.86 125.63
8.89 (350") 5.334 7.112 14.60 19.51 19.61 29.43 29.44 49.21 49.22 78.34 78.07 146.63
10.16 (400") 6.096 8.128 16.70 22.31 22.43 33.65 33.66 56.26 56.26 89.55 89.28 167.63
12.7 (500") 7.620 10.160 20.89 27.92 28.05 42.09 42.10 70.35 70.36 111.96 111.69 209.62
15.24 (600") 9.144 12.192 25.09 33.52 33.68 50.53 50.54 84.45 84.45 134.38 134.11 251.62
Lens type Zoom lens Fixed-focus lens
Model number of
projection lens
ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5
Throw ratio
Û
1.4–1.6 : 1 1.9–2.5 : 1 2.5–3.6 : 1 3.6–6.9 : 1 1.0 : 1
Screen dimensions Projection distance (L)
Screen size
Effective
height
(SH)
Effective
width
(SW)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Min.
(LW)
Max.
(LT)
Fixed
1.78 (70") 1.067 1.422 1.92 2.30 2.69 3.48 3.47 5.05 5.01 9.77 1.43
2.03 (80") 1.219 1.626 2.21 2.64 3.09 3.99 3.98 5.78 5.75 11.19 1.64
2.29 (90") 1.372 1.829 2.49 2.98 3.49 4.51 4.49 6.52 6.48 12.61 1.86
2.54 (100") 1.524 2.032 2.77 3.32 3.88 5.02 4.99 7.26 7.21 14.03 2.08
3.05 (120") 1.829 2.438 3.34 4.00 4.68 6.05 6.01 8.74 8.68 16.87 2.51
3.81 (150") 2.286 3.048 4.19 5.01 5.87 7.58 7.53 10.95 10.87 21.13 3.16
5.08 (200") 3.048 4.064 5.60 6.71 7.85 10.15 10.07 14.64 14.53 28.23 4.24
6.35 (250") 3.810 5.080 7.01 8.40 9.83 12.71 12.61 18.32 18.20 35.33 5.32
7.62 (300") 4.572 6.096 8.43 10.10 11.82 15.28 15.15 22.01 21.86 42.43 6.40
8.89 (350") 5.334 7.112 9.84 11.80 13.80 17.84 17.68 25.70 25.52 49.53
10.16 (400") 6.096 8.128 11.26 13.49 15.78 20.40 20.22 29.39 29.18 56.64
12.7 (500") 7.620 10.160 14.08 16.88 19.75 25.53 25.30 36.76 36.50 70.84
15.24 (600") 9.144 12.192 16.91 20.27 23.72 30.66 30.38 44.14 43.83 85.04
The throw ratio is based on the value during projection onto a 3 810-mm (150") screen size.:
Û
Note
The projection distances listed here involve an error of ±5 %.
z
When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied
z
size.
Setting up
32
- ENGLISH
Getting Started
If the projector is used with a screen size not listed in this manual, check the diagonal dimension (m) of your
screen and calculate the projection distance using the following formulas.
Calculation formulas for projection distance by lens types
J
(for PT-DZ110XE)
Model number of
projection lens
Throw ratio Aspect ratio Projection distance (L) formula Unit : m
Zoom lens
ET-D75LE1
1.4–1.8 : 1 16 : 10
Min. : L = 1.1732 × SD (m)
-
0.0760
Max. : L = 1.5709 × SD (m)
-
0.1004
1.4–1.8 : 1 16 : 9
Min. : L = 1.2087 × SD (m)
-
0.0760
Max. : L = 1.6142 × SD (m)
-
0.1004
1.6–2.2 : 1 4 : 3
Min. : L = 1.3307 × SD (m)
-
0.0760
Max. : L = 1.7756 × SD (m)
-
0.1004
ET-D75LE2
1.8–2.8 : 1 16 : 10
Min. : L = 1.5748 × SD (m)
-
0.0795
Max. : L = 2.3661 × SD (m)
-
0.1064
1.8–2.8 : 1 16 : 9
Min. : L = 1.6220 × SD (m)
-
0.0795
Max. : L = 2.4291 × SD (m)
-
0.1064
2.2–3.3 : 1 4 : 3
Min. : L = 1.7835 × SD (m)
-
0.0795
Max. : L = 2.6772 × SD (m)
-
0.1064
ET-D75LE3
2.8–4.6 : 1 16 : 10
Min. : L = 2.3661 × SD (m)
-
0.0958
Max. : L = 3.9488 × SD (m)
-
0.1216
2.8–4.6 : 1 16 : 9
Min. : L = 2.4291 × SD (m)
-
0.0958
Max. : L = 4.0591 × SD (m)
-
0.1216
3.3–5.6 : 1 4 : 3
Min. : L = 2.6772 × SD (m)
-
0.0958
Max. : L = 4.4724 × SD (m)
-
0.1216
ET-D75LE4
4.6–7.4 : 1 16 : 10
Min. : L = 3.9488 × SD (m)
-
0.1158
Max. : L = 6.2795 × SD (m)
-
0.1013
4.6–7.4 : 1 16 : 9
Min. : L = 4.0591 × SD (m)
-
0.1158
Max. : L = 6.4528 × SD (m)
-
0.1013
5.6–8.9 : 1 4 : 3
Min. : L = 4.4724 × SD (m)
-
0.1158
Max. : L = 7.1102 × SD (m)
-
0.1013
ET-D75LE8
7.3–13.8 : 1 16 : 10
Min. : L = 6.2795 × SD (m)
-
0.3862
Max. : L = 11.7677 × SD (m)
-
0.3598
7.3–13.8 : 1 16 : 9
Min. : L = 6.4567 × SD (m)
-
0.3862
Max. : L = 12.0945 × SD (m)
-
0.3598
8.8–16.5 : 1 4 : 3
Min. : L = 7.1102 × SD (m)
-
0.3862
Max. : L = 13.3189 × SD (m)
-
0.3598
ET-D75LE6
0.9–1.1 : 1 16 : 10
Min. : L = 0.7913 × SD (m)
-
0.0566
Max. : L = 0.9488 × SD (m)
-
0.0736
0.9–1.1 : 1 16 : 9
Min. : L = 0.8150 × SD (m)
-
0.0566
Max. : L = 0.9764 × SD (m)
-
0.0736
1.1–1.3 : 1 4 : 3
Min. : L = 0.8976 × SD (m)
-
0.0566
Max. : L = 1.0748 × SD (m)
-
0.0736
ET-D75LE10
1.3–1.7 : 1 16 : 10
Min. : L = 1.1181 × SD (m)
-
0.0857
Max. : L = 1.4449 × SD (m)
-
0.1085
1.3–1.7 : 1 16 : 9
Min. : L = 1.1496 × SD (m)
-
0.0857
Max. : L = 1.4843 × SD (m)
-
0.1085
1.6–2.0 : 1 4 : 3
Min. : L = 1.2677 × SD (m)
-
0.0857
Max. : L = 1.6378 × SD (m)
-
0.1085
ET-D75LE20
1.7–2.4 : 1 16 : 10
Min. : L = 1.4331 × SD (m)
-
0.0832
Max. : L = 2.0787 × SD (m)
-
0.1162
1.7–2.4 : 1 16 : 9
Min. : L = 1.4724 × SD (m)
-
0.0832
Max. : L = 2.1378 × SD (m)
-
0.1162
2.0–2.9 : 1 4 : 3
Min. : L = 1.6220 × SD (m)
-
0.0832
Max. : L = 2.3543 × SD (m)
-
0.1162
ET-D75LE30
2.4–4.7 : 1 16 : 10
Min. : L = 2.0630 × SD (m)
-
0.1131
Max. : L = 4.0039 × SD (m)
-
0.1765
2.4–4.7 : 1 16 : 9
Min. : L = 2.1220 × SD (m)
-
0.1131
Max. : L = 4.1142 × SD (m)
-
0.1765
2.9–5.6 : 1 4 : 3
Min. : L = 2.3386 × SD (m)
-
0.1131
Max. : L = 4.5315 × SD (m)
-
0.1765
Fixed-
focus lens
ET-D75LE5
0.7 : 1 16 : 10 L = 0.6063 × SD (m)
-
0.0835
0.7 : 1 16 : 9 L = 0.6220 × SD (m)
-
0.0835
0.8 : 1 4 : 3 L = 0.6850 × SD (m)
-
0.0835
Setting up
ENGLISH -
33
Getting Started
Calculation formulas for projection distance by lens types
J
(for PT-DS100XE)
Model number of
projection lens
Throw ratio Aspect ratio Projection distance (L) formula Unit : m
Zoom lens
ET-D75LE1 1.5–2.0 : 1
4 : 3
Min. : L = 1.2087 × SD (m)
-
0.0760
Max. : L = 1.6142 × SD (m)
-
0.1004
16 : 9
Min. : L = 1.3150 × SD (m)
-
0.0760
Max. : L = 1.7559 × SD (m)
-
0.1004
ET-D75LE2 2.0–3.0 : 1
4 : 3
Min. : L = 1.6220 × SD (m)
-
0.0795
Max. : L = 2.4291 × SD (m)
-
0.1064
16 : 9
Min. : L = 1.7638 × SD (m)
-
0.0795
Max. : L = 2.6457 × SD (m)
-
0.1064
ET-D75LE3 3.0–5.0 : 1
4 : 3
Min. : L = 2.4291 × SD (m)
-
0.0958
Max. : L = 4.0591 × SD (m)
-
0.1216
16 : 9
Min. : L = 2.6457 × SD (m)
-
0.0958
Max. : L = 4.4213 × SD (m)
-
0.1216
ET-D75LE4 5.0–8.0 : 1
4 : 3
Min. : L = 4.0591 × SD (m)
-
0.1158
Max. : L = 6.4528 × SD (m)
-
0.1013
16 : 9
Min. : L = 4.4213 × SD (m)
-
0.1158
Max. : L = 7.0315 × SD (m)
-
0.1013
ET-D75LE8
7.9–15.0 : 1 4 : 3
Min. : L = 6.4567 × SD (m)
-
0.3862
Max. : L = 12.0945 × SD (m)
-
0.3598
8.0–15.0 : 1 16 : 9
Min. : L = 7.0315 × SD (m)
-
0.3862
Max. : L = 13.1732 × SD (m)
-
0.3598
ET-D75LE6 1.0–1.2 : 1
4 : 3
Min. : L = 0.8150 × SD (m)
-
0.0566
Max. : L = 0.9764 × SD (m)
-
0.0736
16 : 9
Min. : L = 0.8858 × SD (m)
-
0.0566
Max. : L = 1.0630 × SD (m)
-
0.0736
ET-D75LE10 1.4–1.8 : 1
4 : 3
Min. : L = 1.1417 × SD (m)
-
0.0857
Max. : L = 1.4764 × SD (m)
-
0.1085
16 : 9
Min. : L = 1.2441 × SD (m)
-
0.0857
Max. : L = 1.6102 × SD (m)
-
0.1085
ET-D75LE20 1.8–2.6 : 1
4 : 3
Min. : L = 1.4606 × SD (m)
-
0.0832
Max. : L = 2.1260 × SD (m)
-
0.1162
16 : 9
Min. : L = 1.5906 × SD (m)
-
0.0832
Max. : L = 2.3150 × SD (m)
-
0.1162
ET-D75LE30 2.6–5.1 : 1
4 : 3
Min. : L = 2.1102 × SD (m)
-
0.1131
Max. : L = 4.0906 × SD (m)
-
0.1765
16 : 9
Min. : L = 2.2953 × SD (m)
-
0.1131
Max. : L = 4.4567 × SD (m)
-
0.1765
Fixed-
focus lens
ET-D75LE5 0.8 : 1
4 : 3
L = 0.6220 × SD (m)
-
0.0835
16 : 9
L = 0.6772 × SD (m)
-
0.0835
Setting up
34
- ENGLISH
Getting Started
Calculation formulas for projection distance by lens types
J
(for PT-DW90XE)
Model number of
projection lens
Throw ratio Aspect ratio Projection distance (L) formula Unit : m
Zoom lens
ET-D75LE1
1.5–2.0 : 1 16 : 9
Min. : L = 1.3504 × SD (m) -
0.0760
Max. : L = 1.8031 × SD (m) -
0.1004
2.0–2.7 : 1 4 : 3
Min. : L = 1.6496 × SD (m)
-
0.0760
Max. : L = 2.2047 × SD (m)
-
0.1004
ET-D75LE2
2.1–3.1 : 1 16 : 9
Min. : L = 1.8110 × SD (m)
-
0.0795
Max. : L = 2.7126 × SD (m)
-
0.1064
2.7–4.1 : 1 4 : 3
Min. : L = 2.2165 × SD (m)
-
0.0795
Max. : L = 3.3228 × SD (m)
-
0.1064
ET-D75LE3
3.1–5.2 : 1 16 : 9
Min. : L = 2.7126 × SD (m)
-
0.0958
Max. : L = 4.5315 × SD (m)
-
0.1216
4.1–6.9 : 1 4 : 3
Min. : L = 3.3228 × SD (m)
-
0.0958
Max. : L = 5.5472 × SD (m)
-
0.1216
ET-D75LE4
5.2–8.2 : 1 16 : 9
Min. : L = 4.5315 × SD (m)
-
0.1158
Max. : L = 7.2087 × SD (m)
-
0.1013
6.9–11.0 : 1 4 : 3
Min. : L = 5.5472 × SD (m)
-
0.1158
Max. : L = 8.8228 × SD (m)
-
0.1013
ET-D75LE8
8.2–15.4 : 1 16 : 9
Min. : L = 7.2087 × SD (m)
-
0.3862
Max. : L = 13.5039 × SD (m)
-
0.3598
10.9–20.6 : 1 4 : 3
Min. : L = 8.8228 × SD (m)
-
0.3862
Max. : L = 16.5354 × SD (m)
-
0.3598
ET-D75LE6
1.0–1.2 : 1 16 : 9
Min. : L = 0.9094 × SD (m)
-
0.0566
Max. : L = 1.0906 × SD (m)
-
0.0736
1.4–1.6 : 1 4 : 3
Min. : L = 1.1142 × SD (m)
-
0.0566
Max. : L = 1.3346 × SD (m)
-
0.0736
ET-D75LE10
1.4–1.9 : 1 16 : 9
Min. : L = 1.2756 × SD (m)
-
0.0857
Max. : L = 1.6496 × SD (m)
-
0.1085
1.9–2.5 : 1 4 : 3
Min. : L = 1.5630 × SD (m)
-
0.0857
Max. : L = 2.0197 × SD (m)
-
0.1085
ET-D75LE20
1.8–2.7 : 1 16 : 9
Min. : L = 1.6339 × SD (m)
-
0.0832
Max. : L = 2.3701 × SD (m)
-
0.1162
2.5–3.6 : 1 4 : 3
Min. : L = 2.0000 × SD (m)
-
0.0832
Max. : L = 2.9055 × SD (m)
-
0.1162
ET-D75LE30
2.7–5.2 : 1 16 : 9
Min. : L = 2.3543 × SD (m)
-
0.1131
Max. : L = 4.5669 × SD (m)
-
0.1765
3.6–6.9 : 1 4 : 3
Min. : L = 2.8819 × SD (m)
-
0.1131
Max. : L = 5.5906 × SD (m)
-
0.1765
Fixed-
focus lens
ET-D75LE5
0.8 : 1 16 : 9
L = 0.6929 × SD (m)
-
0.0835
1.0 : 1 4 : 3
L = 0.8504 × SD (m)
-
0.0835
Front leg adjusters and throwing angle
You can screw up/down the front leg adjusters to control the angle of the projector for adjusting the throwing
angle.
Attention
Heated air comes out of the air exhaust port. Do not touch the air exhaust port directly.
z
Adjustable range
Front adjuster leg : 50 mm
Rear adjuster leg : 10 mm
Connections
ENGLISH -
35
Getting Started
Connections
Before connection to the projector
Read carefully the instruction manual for the device to be connected.
z
Turning off the power switch of the devices before connecting cables.
z
If any connection cable is not supplied with the device, or if no optional cable is available for connection of the
z
device, prepare a necessary system connection cable to suit the device.
Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture.
z
In this case, a time base corrector (TBC) must be connected.
The projector accepts the following signals: VIDEO, S-VIDEO, analogue-RGB (with TTL sync. Level) and
z
digital signal.
Some computer models are not compatible with the projector.
z
When using long cables to connect with each of equipment to the projector, there is a possibility that the image
z
will not be output correctly unless a compensator is used.
Pin assignments and signal names of <S-VIDEO IN> terminal
J
Outside view
Pin No. Signal names
GND (luminance signal)
GND (color signal)
Luminance signal
Color signal
Pin assignments and signal names of <RGB2 IN> terminal
J
Outside view
Pin No. Signal names
, : Not assigned
- , , : GND terminals
R/P
R
G/G SYNC/Y
B/P
B
DDC data
HD/SYNC
VD
DDC clock
Pin assignments and signal names of <HDMI IN> terminal
J
Outside view
Pin No. Signal names Pin No. Signal names
T.M.D.S data 2+ T.M.D.S data 2 shield
T.M.D.S data 2
-
T.M.D.S data 1+
T.M.D.S data 1 shield T.M.D.S data 1
-
T.M.D.S data 0+ T.M.D.S data 0 shield
T.M.D.S data 0
-
T.M.D.S clock +
T.M.D.S clock shield T.M.D.S clock
-
CEC
SCL SDA
DDC/CEC GND +5V
Hot plug detection
Even-numbered
pins to
Odd-numbered
pins to
Connections
36
- ENGLISH
Getting Started
Pin assignments and signal names of <DVI-D IN> terminal
J
Outside view
Pin No. Signal names Pin No. Signal names
T.M.D.S data 2
-
T.M.D.S data 2+ +5V
T.M.D.S data 2/4 shield GND
Hot plug detection
T.M.D.S data 0
-
DDC clock T.M.D.S data 0+
DDC data T.M.D.S data 0/5 shield
T.M.D.S data 1
-
T.M.D.S data 1+ T.M.D.S clock shield
T.M.D.S data 1/3 shield T.M.D.S clock +
T.M.D.S clock
-
Connecting example : AV equipment
Attention
When connecting with a video deck, be sure to use the one with a built-in time base corrector (TBC) or use a TBC between
z
the projector and the video deck.
If nonstandard burst signals are connected, the image may be distorted. If this is the case, connect a TBC between the
z
projector and the video deck.
Note
When using an HDMI cable, check that it is compliant with the HDMI standard. Using a cable that is not compliant with the
z
HDMI standard may result in problems such as the image cutting out or not appearing.
When connecting the 1 080p signal using HDMI, use a cable compliant with 1 080p signal.
It is possible to connect the HDMI input terminal with an external device having a DVI terminal using an HDMI/DVI
z
conversion cable, but with some devices the images may not appear or other problems may occur. (
Æ
page 74)
It is possible to connect the DVI-D input terminal with an HDMI- or DVI-D compliant device, but with some devices the
z
images may not appear or other problems may be encountered in operation. (
Æ
page 73)
DVD player
with HDMI terminal
or
Video deck
(TBC built-in)
Control
Computer
Connections
ENGLISH -
37
Getting Started
Connecting example : Computers
Note
The DVI-D signal input terminal supports only a single link.
z
For the specications of the RGB signals that can be applied from the PC, refer to “List of compatible signals”.
z
(
Æ
page 123)
If your computer has the resume feature (last memory), the computer may not function properly until the resume capability
z
is disabled.
When the SYNC ON GREEN signal is input, do not input sync signals to the SYNC/HD and VD terminals.
z
When using the DVI-D input, EDID settings may be required for the connected device.
z
(
Æ
page 73)
When using an HDMI cable, check that it is compliant with the HDMI standard. Using a cable that is not compliant with the
z
HDMI standard may result in problems such as the image cutting out or not appearing.
When connecting the 1 080p signal using HDMI, use a cable compliant with 1 080p signal.
It is possible to connect the HDMI input terminal with an external device having a DVI terminal using an HDMI/DVI
z
conversion cable, but with some devices the images may not appear or other problems may occur. (
Æ
page 74)
ComputerComputer
Computer
Control
Computer
Control
Computer
Removing/attaching the projection lens (optional)
38
- ENGLISH
Getting Started
Removing/attaching the projection lens (optional)
Move the lens to the home position before replacing or removing the projection lens. (
Æ
page 44)
How to install the projection
lens
Align the mark (orange) on the 1 )
projection lens with the mark on
the projector ( on the left side of
LOCK), then insert the lens and turn it
clockwise until there is a click.
Ensure that the mark on the projection lens is
z
aligned with the tip of the mark (arrow) on the
projector.
Fix the projection lens with the 2 )
attached “Lens xing screw”.
Û
Tighten the screw into the rst screw hole
z
on the right side of the mark (orange) of the
projection lens with a Phillips-head screwdriver.
(There is not the projection lens xing tap hole
on all the lenses.)
How to remove the projection
lens
Remove the “Lens xing screw”. 1 )
Û
Remove the rst screw on the right side of the
z
mark (orange) of the projection lens with a
Phillips-head screwdriver.
While holding down the “LOCK 2 )
button”, turn the projection lens
counterclockwise, and then pull it off.
Turn the projection lens counterclockwise until
z
its mark (orange) is aligned with the mark on
the projector ( on the left side of LOCK).
Some types of the lens do not have the projection lens xing screw hole.:
Û
Attention
Do not touch the lens signal receiver. Dust or dirt may cause defective contact.
z
Do not touch the surface of the projection lens with your bare hands.
z
Store the replaced lens where it will be free from vibration and impact.
z
Turn the projection lens counter clockwise to conrm that it does not come out.
z
LOCK button
Powering ON/OFF
ENGLISH -
39
Basic Operation
Powering ON/OFF
Connecting the power cord
Be sure to Insert the attached power cord securely to its base to prevent it from coming off.
Before connecting the power cord, conrm that the MAIN POWER switch is in the “ ” (OFF) position.
Installation
J
Insert the plug securely until its right
and left claw click.
Removal
J
Remove the power cord from the
electrical outlet while pressing the
knobs on its sides.
Powering ON/OFF
40
- ENGLISH
Basic Operation
Powering up the projector
When using an optional lens, install a projection lens
before switch on the projector. (
Æ
page 38)
Remove the projection lens cover from the lens.
Connect the supplied power cable.1 )
(AC220 V-240V 50Hz/60 Hz)
Press the [ | ] marked side of the 2 )
MAIN POWER switch to turn on the
power.
The POWER indicator lamp on the projector will
ash in red. After a short period, the indicator will
illuminate and the projector will enter standby
mode.
Press POWER ON ( | ).3 )
[Power indicator] lamp illuminates in green and
soon the image is projected on the screen.
Note
If the projector is powered up at about 0 °C, a warm-up
z
period of approximately 5 minutes may be necessary to
start projection. <TEMP> indicator lamp lights up during
the warm-up period. When the warm-up is completed,
<TEMP> indicator lamp turns off and the image is
projected on the screen.
If the temperature of the operating environment is low
z
and warm-up takes more than 5 minutes, the projector
will judge that a problem has occurred and the power
will be turned off automatically. If this happens, increase
the temperature around the projector so that it is 0 °C or
higher, and then turn on the MAIN POWER switch and
the POWER ON ( | ) switch once more.
With [ECO] setting in [Standby mode]
z
(
Æ
page 82), When
switch on the projector, projection will start about 10
seconds late.
If the lter is not installed, the power is turned off
z
automatically after 10 minutes.
If projection was stopped last time by using the DIRECT
z
POWER OFF function, it can be started by setting the
MAIN POWER switch to the “ I ” (ON) position.
Making adjustment and
selection
It is recommended that the images are projected
continuously for at least 30 minutes before the focus
is adjusted.
Press <FOCUS> button, roughly 4 )
adjust the focus of the lens.
(
Æ
page 42)
Select and set the projection scheme 5 )
of [INSTALLATION] and [COOLING
CONDITION] settings in [PROJECTOR
SETUP] menu.
Select the input signal by pressing 6 )
<INPUT SELECT> button (<RGB1>,
<RGB2>, <DVI-D/HDMI>, <VIDEO>
<S-VIDEO>, <SDI>).
(SDI: PT-DZ110XE/ PT-DS100XE only)
Adjust the tilt of the main unit in front 7 )
and rear or right and left.
Press <SHIFT> button to adjust the 8 )
position of the projection.
Press <AUTO SETUP> button if the 9 )
input signal is RGB signal.
Zoom the lens so the image lls the 10)
screen.
Readjust the focus.11)
Readjust the zoom so that the image 12)
size ts in the screen.
2)1) 7) 6) 9)
3) 5) 4)
8), 10), 11), 12)
9)3)
5)
4), 11) 8)
6)
10), 12)
Powering ON/OFF
ENGLISH -
41
Basic Operation
Powering off the projector
Press POWER STANDBY (1 ) ).
Press ◄► to select [OK] and press 2 )
(ENTER).
(or press POWER STANDBY (
)
again.)
The projection of the image stops, and [Power
indicator] lamp of the main unit lights up orange.
(The cooling fan keeps running.)
Wait until the power indicator lamp of 3 )
the main unit turns to red (i.e., until
the cooling fan stops).
Press the [4 )
] marked side of the
(MAIN POWER) switch to remove all
power from the projector.
Note
In the cooling state after the power is turned off, the
z
lamp will not light up even if the power is turned on.
To light up the lamp, turn on the power supply again
when the lamp has been cooled sufciently. Failure
to observe this may shorten the lamp life.
The projector consumes approximately 8 W (240 V
z
mode) power.
(STANDBY MODE: [NORMAL])
Direct power off function
The power supplied internally causes the cooling fan
to continue operating and cool off in the event that
the power has failed or even after the power cord is
accidentally disconnected immediately after the power
has been turned off.
Note
When the lamp has been cooled by the direct power off
z
function, it sometimes takes longer than usual for the
lamp to light up again.
While the cooling fan is operating, do not place the
z
projector inside a box or bag.
If projection was stopped by using the DIRECT POWER
z
OFF function, it can be started by setting the MAIN
POWER switch to the “ I ” (ON) position.
3) 4) 2) 1)
2)
1)
Projecting
42
- ENGLISH
Basic Operation
Projecting
Check the connections of the peripheral devices, installation of the projection lens (
Æ
page 38), and connection
of the power cord (
Æ
page 39) and switch on the power (
Æ
page 40) to start the projector. Select the input signal
and adjust the image.
Selecting the input signal
Select an input signal.
The image selected with <INPUT SELECT> button is
projected. (
Æ
page 47)
Attention
Images may not be projected properly depending on the
z
connected device and DVD, video tape, etc. to be played.
Select a system format that is suitable for the input signal
using the [SYSTEM SELECTOR] in the [PICTURE] menu
(
Æ
page 58).
Check the aspect ratios of the screen and the image and
z
select the optimum aspect ratio using [ASPECT] in the
[PICTURE] menu (
Æ
page 59).
How to adjust the focus,
zoom and shift
Use the Lens Shift, Zoom, and Focus controls to
properly frame the image on the screen.
At the projector
J
Press <LENS> button on the control 1 )
panel.
Pressing the button changes the setup screen
z
in the order of [FOCUS], [ZOOM] and [SHIFT].
Press ▲▼◄► to select an item and 2 )
adjust it.
Using the remote control
J
Press <LENS> (FOCUS, ZOOM, SHIFT) 1 )
button on the remote control.
Press <FOCUS> button :
z
Adjust focus.
Press <ZOOM> button :
z
Adjust zoom.
Press <SHIFT> button :
z
Adjust focus.
Press ▲▼◄► to select an item and 2 )
adjust it.
Note
Be careful not to catch your ngers between the lens and
z
shroud when shifting the lens.
The zoom adjustment menu will be displayed only when
z
a lens with zoom function is installed.
When using ET-D75LE5, set the shift to the home
z
position.
The adjustment can be performed faster by pressing and
z
holding the ▲▼◄► for about 7 seconds or more.
It is recommended that the images are projected
z
continuously for at least 30 minutes before the focus is
adjusted.
If the power is turned off during focus or shift adjustment,
z
the LENS CALIBRATION must be performed when the
power is turned on next time.
If the main power is turned off during focus adjustment,
z
the LENS CALIBRATION will be performed automatically
when the focus is adjusted next time.
If the main power is turned off during shift adjustment,
z
“LENS CALIBRATION ERROR” is displayed when the
shift is adjusted next time. Please perform the [LENS
CALIBRATION] from the menu (
Æ
page 86)
If “LENS CALIBRATION ERROR” is still displayed after
z
the LENS CALIBRATION is performed, ask your dealer
for repair.
Projecting
ENGLISH -
43
Basic Operation
Adjustment range after lens position (optical shift)
Do not move the lens beyond the bounds of the shift range as this may cause a change in the focus. This
limitation is to protect the parts of the projector.
Using the standard projection position as the reference, the optical axis shift function makes it possible to adjust
the projection position in the ranges shown in the gures below.
Model number
of
projection lens
Zoom lens
ET-D75LE6
ET-D75LE1, ET-D75LE2, ET-D75LE3,
ET-D75LE4, ET-D75LE8, ET-D75LE10,
ET-D75LE20, ET-D75LE30
PT-DZ110XE
PT-DS100XE
PT-DW90XE
Note
The ET-D75LE5 has a xed focal point, and so shift adjustment cannot be carried out.
z
0.44 V
0.12 V
0.15 H
Standard
projection position
0.44 V
0.12 V
0.15 H
0.12 V
Projected screen
height, V
0.12 V
Projected screen
width, H
0.55 V
0.12 V
0.2 H
Standard
projection position
0.55 V
0.12 V
0.2 H
0.12 V
Projected screen
height, V
0.12 V
Projected screen
width, H
0.40 V
0.12 V
0.2 H
Standard
projection position
0.40 V
0.12 V
0.2 H
0.12 V
Projected screen
height, V
0.12 V
Projected screen
width, H
0.50 V
0.1 V
0.3 H
Standard
projection position
0.50 V
0.1 V
0.3 H
0.1 V
Projected screen
height, V
0.1 V
Projected screen
width, H
0.60 V
0.20 V
0.20 H
Standard
projection position
0.60 V
0.20 V
0.20 H
0.20 V
Projected screen
height, V
0.20 V
Projected screen
width, H
0.70 V
0.20 V
0.30 H
Standard
projection position
0.70 V
0.20 V
0.30 H
0.20 V
Projected screen
height, V
0.20 V
Projected screen
width, H
Projecting
44
- ENGLISH
Basic Operation
Moving the projection lens position to the home position
Press and hold <LENS> button on the projectors controls or <SHIFT> button on the 1 )
remote control for 3 seconds or more.
Press <ENTER> button while the menu shown above is being displayed. (It will be 2 )
displayed for about 5 seconds.)
[PROGRESS] will appear in the menu, and the projection lens will move to the home position.
z
Attention
[HOME POSITION] for the projection lens is the lens position when the lens is being replaced or when the projector is
z
being stored away, and it is not the optical center of the screen.
Lens adjustment to compensate for uneven screen focus
About the focus balance
J
Relationship between lens orientation and screen focus
Q
If the projection lens is tilted with respect to the plane of the screen, uneven focus will result.
Figure 1 : Illustration of inuence of lens orientation
CANCEL
OK
[MENU]
[ENTER]
HOME POSITION
LENS
Image formation surface
Projection lens
Screen surface versus focal point
Projecting
ENGLISH -
45
Basic Operation
Procedure for adjusting the focus balance
J
(tilt compensation in the lens mount)
Three focus adjustment screws on the lens mount may be used to compensate for uneven screen focus.
Structure of lens mount
Q
The three adjustment screws allow the lens to be tilted up and down, and three more screws lock down the
adjustment.
Figure 2 : Front view of lens mount (when viewed from screen side)
Lens bracket Locking screw
(Adjust the focus adjustment screws , and after installing the lens.)
Projecting
46
- ENGLISH
Basic Operation
If the lens is heavy or the projector is installed so that it is tilted, the lens may be tilted, resulting in the focus
becoming unbalanced.
In such a case, refer to the gure 3 and table below, and follow the procedure below to perform adjustment.
Adjustment procedure
Q
Display the internal test pattern grid, and defocus the image.
Adjust the lens focus till one or more sides of the grid comes into focus. Note the appropriate screws
for the out-of-focus sides of the grid as described below.
Loosen the locking screws for each of the adjustment screws , and as needed, following the
indications in the example. The screws to be adjusted correspond to the out-of-focus sides of the
image.
Attention
Make adjustments in up to two places, and fully turn the screw clockwise in at least one place.
z
Turn the adjustment screws (corresponding to the locking screws loosened in step 3)
counterclockwise slightly till the out-of-focus image sides are in focus. (Turning the screws
counterclockwise moves the lens bracket and tilts the lens toward the screen.)
Readjust the lens shift position with the remote if needed.
Refocus the image as in steps 1 and 2 above. Fine adjust the focus evenness as needed, as described
in step 4.
When adjustment is complete, tighten the locking screws.
Adjust the Focus.
Tool to be used : Allen hex socket driver or Allen wrench (2.5 mm diagonal hexagon)
An Allen wrench is supplied with the ET-D75LE6 and ET-D75LE8 optional lens.
Figure 3 : Relation between the adjustment place and adjustment screw
When optimal focus point
is at the back of screen
for V up
When optimal focus point
is at the back of screen
for V bottom
When optimal focus point
is at the back of screen
for H left
When optimal focus point
is at the back of screen
for H right
Turn counterclockwise ——— ——— ———
——— Turn counterclockwise Turn counterclockwise ———
——— Turn counterclockwise ——— Turn counterclockwise
Adjustment place :
The place where the just-in-focus
point is at the back.
Projector
Screen
Basic operations using the remote control
ENGLISH -
47
Basic Operation
Basic operations using the remote control
Using the SHUTTER function
If the projector is not used for a certain period of
time during the meeting intermission, for example, a
shutter mode is available that allows the user to hide
images temporarily.
button
Press <SHUTTER> button on the 1 )
remote control or the main unit.
The projected light is blocked by the internal
z
shutter.
Press <SHUTTER> button again.2 )
Projection resumes.
z
Note
The power indicator will ash while the SHUTTER
z
function is being used.
On-screen display function
This button electronically mutes the onscreen menus
to avoid disrupting the program.
button
Press <ON SCREEN> button on the
remote control.
Switching the input signal
You can use the remote control to switch the signals
that are being input and projected.
button
Press <INPUT SELECT> button on the
remote control or the main unit.
RGB1 Switches to RGB1 input.
RGB2 Switches to RGB2 input.
DVI-D/
HDMI
Switches to DVI-D or HDMI input.
If either of the inputs has already been
selected, the input switches to the
other.
VIDEO Switches to VIDEO input.
S-VIDEO Switches to S-VIDEO input.
SDI
Û
Switches to SDI input.
SDI: PT-DZ110XE/PT-DS100XE only:
Û
STATUS function
Pressing this button displays several pages of
projector status information.
button
Press <STATUS> button on the remote
control.
The [STATUS] screen will be displayed.
z
FUNCTION
ASPECT
SHUTTER
STATUS
AUTO SETUP
TEST PATTERN
ON SCREEN
INPUT SELECT
INPUT
SIGNAL NAME
SIGNAL FREQUENCY
PROJECTOR RUNTIME
LAMP1
LAMP2
INTAKE AIR TEMP.
OPTICS MODULE TEMP.
AROUND LAMP TEMP.
REMAINING FILTER
STATUS
Basic operations using the remote control
48
- ENGLISH
Basic Operation
Automatic adjustment
The automatic setup function can be used to
automatically adjust the resolution, clock phase and
picture position when analog RGB signals consisting
of bitmap images such as computer signals are being
input, or to automatically adjust the picture position
when DVI-D/HDMI signals are being input.
It is recommended to supply images with a bright
white frame at the outermost periphery containing
characters etc. that are clear in white and black
contrast when the system is in automatic adjustment
mode.
Avoid supplying images that involve halftones
or gradation such as photographs and computer
graphics.
button
Press <AUTO SETUP> button on the
remote control or the main unit.
A message [COMPLETE] appears if adjustment is
z
ended normally.
Note
[CLOCK PHASE] may have been shifted even when the
z
adjustment ended normally. In this case, manually adjust
the [CLOCK PHASE].
Refer to “CLOCK PHASE” of “POSITION menu”
(
Æ
page 61) for details.
If an image with blurred edges or a dark image is input,
z
[INCOMPLETE] may appear or adjustment may not
be performed properly even if [COMPLETE] appears.
In this case, manually adjust the items of “INPUT
RESOLUTION” of “ADVANCED MENU” (
Æ
page 65),
“SHIFT” and “CLOCK PHASE” of “POSITION menu”
(
Æ
pages 59, 61).
For specic signals, adjustment should be made
z
according to “AUTO SETUP” of “DISPLAY OPTION
menu” (
Æ
page 72).
[AUTO SETUP] may not be available depending on the
z
machine type of the personal computer.
Automatic adjustment may not available for
z
synchronization signal of C-SYNC and G-SYNC.
Image may be distorted for several seconds during
z
automatic adjustment. This is not a malfunction.
For every supplied signal, adjustment is required.
z
Automatic adjustment can be canceled by pressing
z
<MENU> button during the course of automatic
adjustment.
Even for an RGB signal for which automatic setup is
z
possible, if automatic setup is performed while moving
images are being input, [INCOMPLETE] may appear,
or adjustment may not be performed properly even if
[COMPLETE] appears.
Using the FUNCTION button
[DISABLE], [SUB MEMORY], [SYSTEM SELECTOR],
[SYSTEM DAYLIGHT VIEW], [FREEZE], [P IN P],
or [WAVEFORM MONITOR]
Û
operations can be
assigned to <FUNCTION> button on the remote
control so that it can be used as an easy shortcut
button.
button
Press <FUNCTION> button on the remote
control.
PT-DZ110XE only:
Û
Note
Refer to
z
“FUNCTION BUTTON” of “PROJECTOR SETUP
menu” (
Æ
page 85) for details.
Displaying the internal
test pattern
The projector has 9 types of internal test patterns to
check the condition of the set.
To display test patterns, follow the steps below.
button
Press <TEST PATTERN> button.1 )
Press ◄► to select [TEST PATTERN].2 )
Note
Setting is also possible by using an on-screen menu.
z
Refer to “TEST PATTERN menu” (
Æ
page 89) for details.
Adjustment of the image, picture quality, position, size
z
and other factors will not be reected in test patterns. Be
sure to display an actual input signal before performing
these adjustments.
Basic operations using the remote control
ENGLISH -
49
Basic Operation
Changing the picture aspect
ratio
You can toggle through an appropriate set of aspect
ratios for a given input signal.
button
Press <ASPECT> button on the remote
control.
The setting will change as follows each time
z
<ASPECT> button is pressed.
VID AUTO
*1
DEFAULT
S1 AUTO
*3
VID AUTO
(PRI.)
*3
AUTO
*2
THROUGH
HV FIT
16 : 9
V FIT H FIT 4 : 3
VIDEO/S-VIDEO (NTSC) only*1 :
RGB1/RGB2 (480i, 480p) only*2 :
S-VIDEO (NTSC) only*3 :
Note
Some aspect ratios may not be available for selection
z
depending on the input signal.
Refer to “ASPECT” of “POSITION menu” (
Æ
page 59) for
details.
Menu Navigation
50
- ENGLISH
Settings
Menu Navigation
Menus are extensively used for conguring, adjusting or reconguring the projector.
Navigating through the menu
Operating procedure
J
Press <MENU> button.1 )
[MAIN MENU] appears on the screen.
Press ▲▼ to select the desired item.2 )
The selected item is highlighted in orange.
Press <ENTER> button to establish 3 )
your selection.
The submenu for the selected option will now
open.
0
Press ▲▼ button to highlight the 4 )
desired adjustment item, then press
◄► to change or adjust the parameter
value.
For some items, an individual adjustment screen
containing a bar scale will appear as shown in the
diagram below when ◄► is pressed.
0
Note
Press <MENU> button to return to the previous menu.
z
Some menu items may not be valid for certain signal
z
formats applied to the projector. The menu items that
cannot be adjusted or used are shown in gray characters,
and they cannot be selected.
If no button is pressed for approx. 5 seconds while the
z
individual adjustment screen is displayed, the screen will
return to the previous page.
J
Resetting to the factory default
If an adjustment item is selected and <DEFAULT>
button is pressed, the adjustment value will return
to the factory default setting.
Press
0
Note
You cannot reset all the settings at a time to the factory
z
default settings. To reset all the settings to the factory
defaults, refer to “INITIALIZE” of “PROJECTOR SETUP
menu” (
Æ
87 page).
Some menu items are not available to reset by pressing
z
<DEFAULT> button. Adjust each menu item manually.
The triangle mark under the bar indicates factory default
z
setting and the square indicates the current setting.
The triangle mark position varies by the selected input
signals.
SUB MENU
MENU SELECT
ENTER
PICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
P IN P
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MAIN MENU
SUB MENU
MENU SELECT
ENTER
PICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
P IN P
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MAIN MENU
DEFAULT
OFF
SUB MENU
MENU SELECT
ENTER
SHIFT
ASPECT
ZOOM
CLOCK PHASE
GEOMETRY
POSITION
ADJUST
CONTRAST
ADJUST
CONTRAST
Default setting
Current setting
Menu Navigation
ENGLISH -
51
Settings
MAIN MENU
The main menu consists of the following 11 menu
items.
When a main menu item is selected, the screen
changes to a sub-menu selection screen.
PICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
P IN P
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
SUB MENU
The sub-menu screen of the selected main menu
appears, and you can set and adjust the various items
in the sub-menu.
PICTURE [
J
]
Sub-menu item Default Page
PICTURE MODE STANDARD 53
CONTRAST 0 54
BRIGHTNESS 0 54
COLOR 0 54
TINT 0 54
COLOR TEMPERATURE DEFAULT 55
GAMMA DEFAULT 56
SYSTEM DAYLIGHT VIEW OFF 56
SHARPNESS 6 57
NOISE REDUCTION 2 57
DYNAMIC IRIS 2 57
SYSTEM SELECTOR YP
B
P
R
*1
58
Note
The factory default values may vary depending on the
z
PICTURE MODE.
POSITION [
J
]
Sub-menu item Default Page
SHIFT 59
ASPECT DEFAULT
*1
59
ZOOM 60
CLOCK PHASE 32 61
GEOMETRY
*2
OFF 61
KEYSTONE
*3
63
ADVANCED MENU [
J
]
Sub-menu item Default Page
DIGITAL CINEMA REALITY AUTO
*1
64
BLANKING 64
INPUT RESOLUTION 65
CLAMP POSITION 24
*1
65
EDGE BLENDING OFF 65
FRAME DELAY DEFAULT 67
RASTER POSITION 67
Menu Navigation
52
- ENGLISH
Settings
DISPLAY LANGUAGE [
J
]
Details (
Æ
page 68)
DISPLAY OPTION[
J
]
Sub-menu item Default Page
COLOR MATCHING OFF 69
LARGE SCREEN
CORRECTION
OFF 70
SCREEN SETTING
*2
70
WAVEFORM MONITOR
*4
OFF 71
AUTO SIGNAL OFF 72
AUTO SETUP 72
RGB IN 73
DVI-D IN 73
HDMI IN 74
SDI IN
*2
74
ON-SCREEN DISPLAY 74
BACK COLOR BLUE 75
STARTUP LOGO LOGO2 75
FREEZE 75
PROJECTOR SETUP[
J
]
Sub-menu item Default Page
PROJECTOR ID ALL 76
INSTALLATION
FRONT/
FLOOR
76
HIGH ALTITUDE MODE OFF 76
COOLING CONDITION
FLOOR
SETTING
77
LAMP SELECT DUAL 77
LAMP RELAY OFF 77
LAMP POWER HIGH 78
BRIGHTNESS CONTROL 78
STANDBY MODE NORMAL 82
SCHEDULE OFF 82
RS-232C 83
STATUS 84
NO SIGNAL SHUT-OFF DISABLE 85
REMOTE2 MODE DEFAULT 85
FUNCTION BUTTON 85
DATE AND TIME 85
LENS CALIBRATION 86
FILTER COUNTER RESET 86
SAVE ALL USER DATA 87
LOAD ALL USER DATA 87
INITIALIZE 87
SERVICE PASSWORD 87
P IN P [
J
]
Details (
Æ
page 88)
TEST PATTERN [
J
]
Details (
Æ
page 89)
SIGNAL LIST [
J
]
Details (
Æ
page 90)
SECURITY [
J
]
Sub-menu item Default Page
SECURITY PASSWORD OFF 92
SECURITY PASSWORD
CHANGE
92
DISPLAY SETTING OFF 93
TEXT CHANGE 93
MENU LOCK OFF 93
MENU LOCK PASSWORD 93
CONTROL DEVICE SETUP 94
NETWORK [
J
]
Sub-menu item Default Page
NETWORK SETUP 95
NETWORK CONTROL 95
NETWORK STATUS 95
Note
Some default settings vary by the selected input signal.
z
Sub-menu items vary according to the selected input
z
signal.
Some default settings vary by the selected input *1 :
signal.
PT-DZ110XE/PT-DS100XE only*2 :
PT-DW90XE only*3 :
PT-DZ110XE only*4 :
PICTURE menu
ENGLISH -
53
Settings
PICTURE menu
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
PICTURE MODE
The user can switch to the desired picture mode
suitable for the image source and the environment in
which this projector is used.
Press ▲▼ to select [PICTURE MODE].1 )
Press ◄► to switch [PICTURE MODE].2 )
The setting will change as follows each time
z
◄► is pressed.
STANDARD CINEMA NATURAL
USER DICOM SIM.
GRAPHIC DYNAMIC
STANDARD
The picture becomes suitable for
moving images in general.
CINEMA
The picture becomes suitable for
movie sources.
NATURAL The picture complies with sRGB.
DICOM SIM.
The picture becomes similar to
DICOM Part14 gray scale.
DYNAMIC
The light output is maximized for use
in bright areas.
GRAPHIC
The picture becomes suitable for
input from to the personal computer.
USER
You can set your favorite picture
mode.
Note
Factory defaults are [GRAPHIC] for RGB system and
z
[STANDARD] for moving images.
DICOM is an abbreviation for “Digital Imaging and
z
Communication in Medicine”, which is a standard for
medical imaging devices. Although the name “DICOM” is
used, this projector is not a medical device. Accordingly,
do not use the projected images for medical diagnosis or
similar usage.
When <ENTER> button is pressed while a [PICTURE
z
MODE] other than [USER] is selected, the setting is
saved and will be used as the preset value next time
a signal is inputted. At this time, all the data except
[SYSTEM SELECTOR] in the [PICTURE] menu are
saved.
The factory default of [USER] is the image conformed to
z
ITU-R BT.709 Standard.
Changing the name of [USER]
J
Select [USER] in step 2).1.
Press <ENTER> button.2.
A screen showing details of the [PICTURE
z
MODE] will be displayed.
Press ▲▼ to select [PICTURE MODE 3.
NAME CHANGE].
Press <ENTER> button.4.
The [
z
PICTURE MODE NAME CHANGE]
screen will be displayed.
Press ▲▼◄► to select characters 5 )
and press <ENTER> button to input
them.
Press ▲▼◄► to select [OK], and 6.
press <ENTER> button.
The picture mode name is changed.
z
PICTURE MODE NAME CHANGE
PICTURE menu
54
- ENGLISH
Settings
CONTRAST
You can adjust the contrast of the projected image.
Press ▲▼ to select [CONTRAST].1 )
Press ◄► or <ENTER> button.2 )
The [CONTRAST] individual adjustment screen
z
will be displayed.
Press ◄► to adjust the level.3 )
Operation Adjustment
Adjustment
range
Press ►.
Raises the picture
brightness and the
picture becomes
clearer.
Maximum
value 31
Press ◄.
Lowers the picture
brightness and
weakens the picture.
Minimum
value
-
31
Attention
Adjust the BRIGHTNESS in advance if necessary.
z
BRIGHTNESS
You can adjust the brightness of the projected image.
Press ▲▼ to select [BRIGHTNESS].1 )
Press ◄► or <ENTER> button.2 )
The [BRIGHTNESS] individual adjustment
z
screen will be displayed.
Press ◄► to adjust the level.3 )
Operation Adjustment
Adjustment
range
Press ►.
Increases the
brightness of the
dark (black) parts of
the screen.
Maximum
value 31
Press ◄.
Reduces the
brightness of the
dark (black) parts of
the screen.
Minimum
value
-
31
COLOR
You can adjust the color saturation of the projected
image.
Press ▲▼ to select [COLOR].1 )
Press ◄► or <ENTER> button.2 )
The [COLOR] individual adjustment screen will
z
be displayed.
Press ◄► to adjust the level.3 )
Operation Adjustment
Adjustment
range
Press ►. Deepens colors.
Maximum
value 31
Press ◄. Weakens colors.
Minimum
value
-
31
TINT
You can adjust the skin tone in the projected image.
Press ▲▼ to select [TINT].1 )
Press ◄► or <ENTER> button.2 )
The [TINT] individual adjustment screen will be
z
displayed.
Press ◄► to adjust the level.3 )
Operation Adjustment
Adjustment
range
Press ►.
Adjusts skin tone
toward greenish
color.
Maximum
value 31
Press ◄.
Adjusts skin tone
toward reddish-
purple.
Minimum
value
-
31
PICTURE menu
ENGLISH -
55
Settings
COLOR TEMPERATURE
You can adjust the white balance of the projected
image.
Press ▲▼ to select [COLOR 1 )
TEMPERATURE].
Press ◄► or <ENTER> button.2 )
The [COLOR TEMPERATURE] individual
z
adjustment screen will be displayed.
Press ◄► to switch [COLOR 3 )
TEMPERATURE].
The setting will change as follows each time
z
◄► is pressed.
DEFAULT
Û
USER1 USER2
9300K 3200K
[DEFAULT] cannot be selected when the :
Û
[PICTRUE MODE] has been set to [USER] or
[DICOM SIM.].
Note
When any setting other than [OFF] has been selected
z
for [COLOR MATCHING] (
Æ
page 69), the [COLOR
TEMPERATURE] setting is xed to [USER1].
The value of color temperature is for reference only.
z
To further adjust toward the
J
desired white balance
Select [USER1] or [USER2] in Step 3).4 )
Press <ENTER> button.5 )
The [COLOR TEMPERATURE] screen will be
z
displayed.
Press ▲▼ to select [WHITE 6 )
BALANCE].
Press <ENTER> button.7 )
The [WHITE BALANCE] screen will be
z
displayed.
Press ▲▼ to select [WHITE 8 )
BALANCE HIGH] or [WHITE
BALANCE LOW].
Press <ENTER> button.9 )
The [WHITE BALANCE HIGH (or LOW)]
z
screen will be displayed.
Press ▲▼ to select [RED], [GREEN] 10 )
or [BLUE].
Press ◄► to adjust the level.11 )
Item Operation Adjustment
Adjustment
range
RED
Press ►. Deepens red.
Maximum
value
HIGH : 255
LOW : 127
Minimum
value
HIGH : 0
LOW :
-
127
Default
HIGH : 255
LOW : 0
Press ◄. Weakens red.
GREEN
Press ►. Deepens green.
Press ◄. Weakens green.
BLUE
Press ►. Deepens blue.
Press ◄. Weakens blue.
Note
All colors will not be displayed properly unless adequate
z
adjustment is made. If the adjustment does not look
suitable, you can press <DEFAULT> button to return the
setting for the selected item only to the factory default
setting.
The [COLOR TEMPERATURE] cannot be adjusted
z
for the internal test pattern (
Æ
page 89). Be sure to
project the input signal when adjusting the [COLOR
TEMPERATURE].
Changing the name of [USER 1]
J
or [USER 2]
Select [USER1] or [USER2] in step 3).1.
Press <ENTER> button.2.
The [COLOR TEMPERATURE] screen will be
z
displayed.
Press ▲▼ to select [COLOR 3.
TEMPERATURE NAME CHANGE].
Press <ENTER> button.4.
The [COLOR TEMPERATURE NAME
z
CHANGE] screen will be displayed.
(in units of 100K)
COLOR TEMPERATURE NAME CHANGE
PICTURE menu
56
- ENGLISH
Settings
Press ▲▼◄► to select characters 5 )
and press <ENTER> button to input
them.
Press ▲▼◄► to select [OK], and 6.
press <ENTER> button.
The color temperature setting name is changed.
z
GAMMA
This switches the gamma mode.
Press ▲▼ to select [GAMMA].1 )
Press ◄► or <ENTER> button.2 )
The [GAMMA] individual adjustment screen will
z
be displayed.
Press ◄► to switch [GAMMA].3 )
The setting will change as follows each time
z
◄► is pressed.
DEFAULT
*
USER1
2.8 USER2
DICOM SIM.
1.0
2.0 1.8
[DEFAULT] cannot be selected when the :
Û
[PICTRUE MODE] has been set to [DYNAMIC],
[USER] or [DICOM SIM.].
Note
DICOM is an abbreviation for “Digital Imaging and
z
Communication in Medicine”, which is a standard for
medical imaging devices.
This projector is not a medical device. Do not use the
displayed image for diagnosis.
Changing the name of [USER1]
J
or [USER2]
Select [USER1] or [USER2] in step 3).1.
Press <ENTER> button.2.
The [GAMMA] screen will be displayed.
z
Press ▲▼ to select [GAMMA NAME 3.
CHANGE].
Press <ENTER> button.4.
The [GAMMA NAME CHANGE] screen will be
z
displayed.
Press ▲▼◄► to select characters 5 )
and press <ENTER> button to input
them.
Press ▲▼◄► to select [OK], and 6.
press <ENTER> button.
The gamma selection name is changed.
z
SYSTEM DAYLIGHT VIEW
This corrects images so that they appear vivid when
projected under bright lighting.
Press ▲▼ to select [SYSTEM 1 )
DAYLIGHT VIEW].
Press ◄► or <ENTER> button.2 )
The [SYSTEM DAYLIGHT VIEW] individual
z
adjustment screen will be displayed.
Press ◄► to switch [SYSTEM 3 )
DAYLIGHT VIEW].
The setting will change as follows each time
z
◄► is pressed.
OFF (No correction) 1 (Low)
3 (High) 2 (Medium)
(in units of 0.1)
GAMMA NAME CHANGE
PICTURE menu
ENGLISH -
57
Settings
SHARPNESS
This adjusts the sharpness of the pictures.
Press ▲▼ to select [SHARPNESS].1 )
Press ◄► or <ENTER> button.2 )
The [SHARPNESS] individual adjustment
z
screen will be displayed.
Press ◄► to adjust the level.3 )
Operation Adjustment
Adjustment
range
Press ►.
Contours become
sharper.
0 - 15
Press ◄.
Contours become
softer.
NOISE REDUCTION
This can be used to adjust pictures if they contain
interference as a result of poor quality of the input
signal.
Press ▲▼ to select [NOISE 1 )
REDUCTION].
Press ◄► or <ENTER> button.2 )
The [NOISE REDUCTION] individual
z
adjustment screen will be displayed.
Press ◄► to switch [NOISE 3 )
REDUCTION].
The setting will change as follows each time
z
◄► is pressed.
1 (Low) 2 (Medium)
OFF (No correction) 3 (High)
Attention
[NOISE REDUCTION] is set active when the selected
z
input signal has less noise. Applying noise reduction may
affect the image quality, if so, set to [OFF].
DYNAMIC IRIS
Pictures with the optimum contrast will be displayed
by automatically providing aperture compensation and
signal compensation to suit the pictures concerned.
Press ▲▼ to select [DYNAMIC IRIS].1 )
Press ◄► or <ENTER> button.2 )
The [DYNAMIC IRIS] individual adjustment
z
screen will be displayed.
Press ◄► to switch [DYNAMIC IRIS].3 )
The setting will change as follows each time
z
◄► is pressed.
OFF
(No correction)
1 (Low)
2
(Intermediate)
USER 3 (High)
To further adjust the selected
J
compensation amount
Select [USER] in step 3).4 )
Press <ENTER> button.5 )
The [DYNAMIC IRIS] screen will be displayed.
z
Press ▲▼ to select the item to be 6 )
adjusted, and press ◄► to adjust the
amount of correction.
AUTO IRIS (Automatic aperture
Q
adjustment)
OFF (No automatic
adjustment)
1 (Low)
255 (High)
2…254
(Intermediate)
MANUAL IRIS (Fixed aperture
Q
adjustment)
OFF (No xed iris) 1 (Low)
255 (High)
2…254
(Intermediate)
DYNAMIC GAMMA (signal
Q
compensation amount adjustment)
OFF (No automatic
correction)
1 (Low)
3 (High) 2 (Intermediate)
Note
The contrast is set to the maximum level when [DYNAMIC
z
IRIS] is set to [3].
PICTURE menu
58
- ENGLISH
Settings
SYSTEM SELECTOR
This enables the projector to automatically recognize
input signals. Furthermore, if unstable signals are
input, the system format can be selected manually.
Press ▲▼ to select [SYSTEM 1 )
SELECTOR].
Press <ENTER> button.2 )
Press ▲▼ to switch [SYSTEM 3 )
SELECTOR].
Press <ENTER> button.4 )
VIDEO/S-VIDEO terminal input
J
signal
Select from AUTO, NTSC, NTSC4.43, PAL,
PAL-M, PAL-N, SECAM, and PAL60.
Attention
[AUTO] mode is selected by default.
z
When the projector is not working properly in [AUTO]
z
mode, change the setting according to each SYSTEM
SELECTOR type.
Note
[AUTO] automatically selects from NTSC, NTSC4.43,
z
PAL, PAL-M, PAL-N, SECAM, and PAL60.
RGB1/RGB2 terminal input signal
J
480i, 576i, 576p signals
z
Select from RGB and YC
B
C
R
.
VGA60, 480p signals
z
Select from VGA60, 480p, and 480pRGB.
Other signals
z
Select from RGB and YP
B
P
R
.
Note
Refer to
z
“List of compatible signals” (
Æ
page 123) for
available signals.
DVI-D terminal input signal
J
480p, 576p signals
z
Select from RGB and YC
B
C
R
.
Other signals
z
Select from RGB and YP
B
P
R
.
Note
Refer to
z
“List of compatible signals” (
Æ
page 123) for
available signals.
Malfunction may occur or other problems could be
z
encountered with some equipment.
HDMI terminal input signal
J
480p, 576p signals
z
Select from Auto, RGB, and YC
B
C
R
.
Other signals
z
Select from Auto, RGB, and YP
B
P
R
Note
Refer to
z
“List of compatible signals” (
Æ
page 123) for
available signals.
Malfunction may occur or other problems could be
z
encountered with some equipment.
SDI terminal input signal
J
(PT-DZ110XE/PT-DS100XE only)
Select from AUTO, 1 080/60i, 1 035/60i,
z
720/60p, 1 080/24p, 1 080/50i, 1 080/30p,
1 080/25p, 1 080/24sF, 720/50p, 480i, and 576i.
Refer to
z
“List of compatible signals”
(
Æ
page 123) for available signals.
To display pictures complying
with the sRGB standard
sRGB is the international color reproduction standard
(IEC61966-2-1) established by IEC (International
Electrotechnical Commission).
To reproduce colors more faithfully in compliance
with the sRGB standard, perform the following setting
procedure.
Set [COLOR MATCHING] adjustment to 1 )
[OFF].
Refer to “COLOR MATCHING”
z
(
Æ
page 69).
Display the [PICTURE] screen.2 )
Refer to
z
“PICTURE menu” (
Æ
page 53).
Press ▲▼ to select [PICTURE MODE].3 )
Press ◄► to select [NATURAL].4 )
Press ▲▼ to select [COLOR].5 )
Press <DEFAULT> button on the 6 )
remote control to restore the factory
default.
Follow the same procedure (steps 7 )
5-6) to restore the factory default for
[TINT], [COLOR TEMPERATURE] and
[GAMMA].
Note
sRGB is only enable when RGB signals are being input.
z
POSITION menu
ENGLISH -
59
Settings
POSITION menu
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
SHIFT
This function allows the user to adjust the raster
position vertically or horizontally if the position of the
image projected on the screen is displaced even
when the projector is properly aligned with the screen,
and the internal test patterns are correctly framed.
Press ▲▼ to select [SHIFT].1 )
Press <ENTER> button.2 )
The [SHIFT] screen will be displayed.
z
Press ▲▼◄► to adjust the position.3 )
For vertical (up and down)
J
adjustment
Operation Adjustment
Press ▲.
The picture
position
moves up.
Press ▼.
The picture
position
moves down.
For horizontal (right and left)
J
adjustment
Operation Adjustment
Press ►.
The picture
position
moves to the
right.
Press ◄.
The picture
position
moves to the
left.
ASPECT
This changes the aspect ratio of the projected image.
This changes the aspect ratio for the screen range
selected with [SCREEN SETTING]. Set [SCREEN
SETTING] rst. (
Æ
page 70)
Press ▲▼ to select [ASPECT].1 )
Press ◄► or <ENTER> button.2 )
The [ASPECT] individual adjustment screen will
z
be displayed.
Press ◄► to switch [ASPECT].3 )
The setting will change as follows each time
z
◄► is pressed.
VID AUTO
*1
DEFAULT S1 AUTO
*3
VID AUTO (PRI.)
*3
AUTO
*2
THROUGH
HV FIT
16 : 9
V FIT H FIT 4 : 3
VIDEO/S-VIDEO (NTSC) only*1 :
RGB1/RGB2 (480i, 480p) only*2 :
S-VIDEO (NTSC) only*3 :
DEFAULT
J
Pictures are displayed without changing the aspect
ratio of the input signals.
VID AUTO
J
The projector identies the video ID (VID)
embedded in the picture signals and displays the
picture by automatically switching the screen sizes
between 4 : 3 and 16 : 9. This function is effective
for the NTSC signal input.
AUTO
J
The projector identies the video ID (VID)
embedded in the picture signals and displays the
picture by automatically switching the screen sizes
between 4 : 3 and 16 : 9. This function is effective
for the 480i/480p signal input.
S1 AUTO
J
The projector identies the S1 signal and displays
the picture by automatically switching the screen
sizes between 4 : 3 and 16 : 9. This function is
effective for S-VIDEO NTSC signals.
POSITION menu
60
- ENGLISH
Settings
VID AUTO (PRI.)
J
The projector identies the abovementioned
VID or S1 signals and displays the picture by
automatically choosing the screen sizes of 4 : 3
or 16 : 9 according to the VID if it is detected or
S1 signals if a VID is not detected. This function is
effective for S-Video NTSC signals.
THROUGH
J
Pictures are displayed without changing the
resolution of the input signals.
16 : 9
J
When standard signals
*4
are input, the pictures
are displayed with the aspect ratio converted to
16 : 9. When wide signals are input
*5
, the pictures
are displayed without changing the aspect ratio.
4 : 3
J
When standard signals
*4
are input, the pictures
are displayed without changing the aspect ratio.
When wide signals are input
*5
and [4:3] is
selected with [SCREEN FORMAT], the aspect
ratio is changed to 4:3. If [4:3] is not selected with
[SCREEN FORMAT], the pictures are reduced so
that they will be in the 4:3 screen without changing
the input aspect ratio.
H FIT
J
The display will use the full width of the screen
range selected with [SCREEN FORMAT]. When
signals have a vertical aspect ratio that is larger
than the screen aspect selected with [SCREEN
FORMAT], the pictures will be displayed with their
bottom areas cut off.
V FIT
J
The display will use the full height of the screen
range selected with [SCREEN FORMAT].
HV FIT
J
The pictures are displayed in the full screen range
selected with [SCREEN FORMAT]. If the aspect
ratios of the input signals and screen range differ,
conversion to the screen aspect set with [SCREEN
FORMAT] is performed and then the pictures are
displayed.
Standard signals are input signals with an aspect *4 :
ratio of 4 : 3 or 5 : 4.
Wide-screen signals are input signals with an *5 :
aspect ratio of 16:10, 16 : 9, 15 : 9 or 15 : 10.
Note
Some size modes are not available for certain types of
z
input signals. For NTSC signals, [DEFAULT] cannot be
selected.
If an aspect ratio which is different from the aspect ratio
z
for the input signals is selected, the pictures will appear
differently from the originals. Be careful of this when
selecting the aspect ratio.
If using this projector in places such as cafes or hotels to
z
display programs for a commercial purpose or for public
presentation, note that adjusting the aspect ratio or using
the zoom function to change the screen pictures may
be an infringement of the rights of the original copyright
owner for that program under copyright protection laws.
If conventional (normal) 4 : 3 pictures which are not
z
wide-screen pictures are displayed on a wide screen,
the edges of the pictures may not be visible or they may
become distorted. Such pictures should be viewed as
with an aspect ratio of 4 : 3 in the original format intended
by the creator of the pictures.
ZOOM
This adjusts the size of the projected pictures.
Press ▲▼ to select [ZOOM].1 )
Press <ENTER> button.2 )
The [ZOOM] screen will be displayed.
z
Press ▲▼ to select [VERTICAL]/ 3 )
[HORIZONTAL], and press ◄► to
adjust.
When [ASPECT] is set to
J
[DEFAULT]
Press ▲▼ to select [MODE].1 )
Press ◄► to switch [MODE].2 )
INTERNAL
Zoom area is the factory default
setting of [SCREEN FORMAT] in
[SCREEN SETTING].
FULL
Enlarges the size of the pictures
using the whole of the display area
selected with [SCREEN FORMAT].
POSITION menu
ENGLISH -
61
Settings
Press ▲▼ to select [INTERLOCKED].3 )
Press ◄► to switch [INTERLOCKED].4 )
OFF
The [VERTICAL] and
[HORIZONTAL] settings are used
as the vertical and horizontal zoom
ratios respectively.
ON
The zoom ratio is set to the [BOTH]
setting.
This allows the pictures to be
zoomed at equal vertical and
horizontal ratios.
Note
When [ASPECT] is set to [THROUGH], [ZOOM] will not
z
appear.
When other than [DEFAULT] is selected for [ASPECT],
z
the [MODE] selection setting will not appear.
CLOCK PHASE
Clock phase adjustment achieves the best image
when the screen ickers or halos are observed around
contours.
Press ▲▼ to select [CLOCK PHASE].1 )
Press ◄► or <ENTER> button.2 )
The [CLOCK PHASE] individual adjustment
z
screen will be displayed.
Press ◄► to adjust the level.3 )
The value changes from 0 to 63. Adjust so that
z
the amount of interference is at a minimum.
Note
The CLOCK PHASE may not be adjusted, depending on
z
the signal.
No optimal value may be obtained if the output of the PC
z
to which the signal input is applied is unstable.
No optimal value may be obtained if the total number of
z
dots is not correct.
The [CLOCK PHASE] can be adjusted only when RGB
z
signal input is applied with RGB1 and RGB2 IN.
GEOMETRY
(PT-DZ110XE/PT-DS100XE only)
Square video can be projected onto a special shaped
screen using unique image processing technology.
Press ▲▼ to select [GEOMETRY].1 )
Press ◄► to switch [GEOMETRY].2 )
The setting will change as follows each time
z
◄► is pressed.
OFF KEYSTONE
PC CURVED
OFF
Geometry correction is not
performed.
KEYSTONE
This adjusts projected images when
they are distorted to a trapezoid.
CURVED
This adjusts projected images
when they are distorted to a curved
surface.
PC
Û
This is for performing geometry
correction from a computer.
GEOMETRY adjustment should be carried out by :
Û
a person who is familiar with the projector or by
a service person because a high level of skill is
required to make successful adjustment.
Select [KEYSTONE] or [CURVED] in 3 )
Step 2), and press <ENTER> button.
The [GEOMETRY : KEYSTONE] or
z
[GEOMETRY : CURVED] screen will be
displayed.
Press ▲▼ to select the desired 4 )
adjustment item, and press ◄► to
adjust the correction amount.
You can adjust the projection images as shown
z
below.
POSITION menu
62
- ENGLISH
Settings
KEYSTONE menu
J
VERTICAL KEYSTONE
z
VERTICAL SUB KEYSTONE
z
HORIZONTAL KEYSTONE
z
HORIZONTAL SUB KEYSTONE
z
LINEARITY
z
CURVED menu
J
LENS THROW RATIO
z
Set to the throw ratio being used (the projection
distance divided by the screen width).
VERTICAL KEYSTONE
z
HORIZONTAL KEYSTONE
z
VERTICAL ARC
z
HORIZONTAL ARC
z
VERTICAL BALANCE
z
HORIZONTAL BALANCE
z
Note
When [GEOMETRY] setting is set, displayed menu or
z
startup logo might be projected outside of the actual
image area.
If both [EDGE BLENDING]
z
(
Æ
page 65) adjustment and
[GEOMETRY] correction are used, [EDGE BLENDING]
adjustment cannot be made correctly.
POSITION menu
ENGLISH -
63
Settings
KEYSTONE
(PT-DW90XE only)
If the projector is aligned non-perpendicularly to the
screen, or if the projection screen has an angled
surface, you can correct keystone.
Press ▲▼ to select [KEYSTONE].1 )
Press <ENTER> button.2 )
Select the desired adjustment item.3 )
Press ◄► to adjust.4 )
KEYSTONE
J
SUB KEYSTONE
J
LINEARITY
J
Note
When [KEYSTONE] setting is set, displayed menu or
z
startup logo might be projected outside of the actual
image area.
You can correct the distortion ±40 ° from the plane. For
z
a better quality image, installing the projector with a
minimum of distortion is recommended.
(ET-D75LE5: ±22 ° , ET-D75LE6:±28 ° )
Some distortion may be retained for lens shift adjustment.
z
The result of the keystone correction will affect the aspect
z
ratio and the size of the image.
ADVANCED MENU
64
- ENGLISH
Settings
ADVANCED MENU
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
DIGITAL CINEMA REALITY
Increase the vertical resolution when the PAL (or
SECAM) 576i signal input or the NTSC 480i, 1 080/50i
and 1 080/60i signal input is applied.
Press ▲▼ to select [DIGITAL CINEMA 1 )
REALITY].
Press ◄► or <ENTER> button.2 )
The [DIGITAL CINEMA REALITY] individual
z
adjustment screen will be displayed.
Press ◄► to select [DIGITAL CINEMA 3 )
REALITY].
The setting will change as follows each time
z
◄► is pressed.
AUTO OFF
25p FIXED : When 576i or 1 080/50i signals are input
30p FIXED : When 480i or 1 080/60i signals are input
AUTO
Performs automatic detection and
cinema processing. (factory default)
OFF Unforced cinema processing.
25p FIXED
Forced cinema processing (2 : 2
pulldown) is performed when a 576i
or 1 080/50i signal is input.
30p FIXED
Forced cinema processing (2 : 2
pulldown) is performed when a 480i
or 1 080/60i signal is input.
Note
In [DIGITAL CINEMA REALITY] mode, the image quality
z
will be deteriorated if [30p FIXED] or [25p FIXED] is
selected when the signal is not a 2 : 2 pulldown signal.
BLANKING
Blanking adjustment ne-tunes the images projected
by the video deck or other devices when the noise
appears on the edges of the screen or if a part of the
image lies slightly offscreen.
Press ▲▼ to select [BLANKING].1 )
Press <ENTER> button.2 )
The [BLANKING] screen will be displayed.
z
Press ▲▼ to select the desired item 3 )
for adjustment.
Press ◄► to adjust blanking.4 )
The adjustment value for the PT-DZ110XE can
z
be changed within a range of 0 to 599 vertically
and 0 to 959 horizontally.
The adjustment value for the PT-DS100XE can
z
be changed within a range of 0 to 524 vertically
and 0 to 699 horizontally.
The adjustment value for the PT-DW90XE can
z
be changed within a range of 0 to 383 vertically
and 0 to 682 horizontally.
When correcting the upper blanking of the
screen (top)
Press ◄ to move the
blanking zone upward;
Press ► to downward.
When correcting the lower blanking of the
screen (bottom)
Press ► to move the
blanking zone upward;
Press ◄ to downward.
When correcting the left hand blanking of the
screen (left)
Press ► to move the
blanking zone to the right;
Press ◄ to the left.
When correcting the right hand blanking of the
screen (right)
Press ◄ to move the
blanking zone to the right;
Press ► to the left.
ADVANCED MENU
ENGLISH -
65
Settings
INPUT RESOLUTION
Input resolution adjustment achieves the best image
when the screen ickers or halo is observed around
the contour. Set the values appropriately for the signal
resolution that is being used.
Press ▲▼ to select [INPUT 1 )
RESOLUTION].
Press <ENTER> button.2 )
The [INPUT RESOLUTION] screen will be
z
displayed.
Press ▲▼ to select [TOTAL DOTS], 3 )
[DISPLAY DOTS], [TOTAL LINES] or
[DISPLAY LINES], and the press ◄►
to adjust it.
Each item automatically displays a value in
z
response to the type of the input signal. If
vertical stripes appear on the screen or the
image is partly missing, increase or decrease
the displayed value while observing the screen
to achieve the optimal value.
Note
The vertical stripes will not appear on the all white signal
z
image.
The picture may be distorted during the adjusting
z
operation, but this is not a fault.
The [INPUT RESOLUTION] can be adjusted only when
z
RGB signal input is applied with RGB1 and RGB2 IN.
CLAMP POSITION
Use the clamp position adjustment to achieve the
optimal value when dark areas of the image are
crushed or displayed in green.
Press ▲▼ to select [CLAMP 1 )
POSITION].
Press ◄► to adjust.2 )
The value changes from 1 to 255.
z
The optimal value for the clamp position
z
adjustment
If dark areas are crushed :
The optimal value is the point where the dark
area is best improved.
If the dark areas are displayed in green :
The optimal value is the point where the green
areas become black and the crushing effect is
rectied.
Note
The [CLAMP POSITION] can be adjusted only when the
z
RGB signal input is applied with RGB1 and RGB2 IN.
The [CLAMP POSITION] may not be adjusted, depending
z
on the signal.
EDGE BLENDING
The built-in edge blending feature allows multiple
projector images to be seamlessly overlapped.
Press ▲▼ to select [EDGE 1 )
BLENDING].
Press ◄► to switch [EDGE 2 )
BLENDING].
The setting will change as follows each time
z
◄► is pressed.
OFF ON USER
OFF
When the multi-screens are not
going to be used.
ON
When the default linear blending
ramps are sufcient.
USER
When a user-dened blending
ramp is required. These ramps can
be dened and uploaded to the
projector through the RS-232 port.
Consult your dealer for details.
Press <ENTER> button.3 )
The [EDGE BLENDING] screen will be
z
displayed.
Press ▲▼ to specify the area to be 4 )
adjusted.
To blend the top edge:
z
set [UPPER] to [ON].
To blend the bottom edge:
z
set [LOWER] to
[ON].
To blend the left edge:
z
set [LEFT] to [ON].
To blend the right edge:
z
set [RIGHT] to [ON].
Press ◄► to toggle [ON] and [OFF].5 )
Press ◄► to adjust the overlap width 6 )
and the starting point.
ADVANCED MENU
66
- ENGLISH
Settings
To display the adjustment marker
J
Press ▲▼ to select [MARKER].7 )
Press ◄► to select [ON].8 )
A marker for adjusting the overlap position
z
appears. The optimal point is the position where
the red line of one frame overlaps the green
line of the other frame.
The blending widths of each projector must be
set to the same value. Optimal blending cannot
be achieved if the widths are different.
Press ▲▼ to select [BRIGHT 9)
ADJUST].
Press <ENTER> button.10)
The [BRIGHT ADJUST] screen will be
z
displayed.
Press ▲▼ to select [BRIGHT INSIDE].11)
Press <ENTER> button.12)
The [BRIGHT INSIDE] individual adjustment
z
screen will be displayed.
When [INTERLOCKED] is set to [OFF],
z
individual adjustment of [RED], [GREEN] and
[BLUE] will be possible.
Press ▲▼ to select an item, and 13)
press ◄► to adjust the setting.
Once adjustment is complete, press <MENU>
z
button to return to [BRIGHT ADJUST] screen.
Press ▲▼ to select the part of 14)
[UPPER], [LOWER], [RIGHT], [LEFT].
Press ◄► to adjust the width for 15)
correcting the [BRIGHT INSIDE]
setting (0 to 255).
Press ▲▼ to select [BRIGHT 16)
OUTSIDE].
Press <ENTER> button.17)
The [BRIGHT OUTSIDE] individual adjustment
z
screen will be displayed.
When [INTERLOCKED] is set to [OFF],
z
individual adjustment of [RED], [GREEN] and
[BLUE] will be possible.
Press ▲▼ to select an item, and 18)
press ◄► to adjust the setting.
Note
The [BRIGHT INSIDE] adjustments are used to match
z
the projector’s main-screen-area black levels to the level
within the blended area.
The [BRIGHT OUTSIDE] adjustments may be used to
ne adjust the thin borders on either side of the blend
area, but are often not needed.
When a rear screen or screen with a high gain is used,
z
the blended areas may appear to be discontinuous
depending on the viewing position.
When using both horizontal and vertical edge blending
z
functions to form a multiple projector image, adjust the
[BRIGHT BLENDING] before performing the adjustment
in Step 11).
When using only one of the horizontal or vertical edge
z
blending functions, set all items of [BRIGHT BLENDING]
to [0].
Red line
Green line
The optimal point is where these lines overlap.
BRIGHT
BLENDING
MAKER
BRIGHT OUTSIDE
Edge blending width (right)
BRIGHT adjustment (right)
BRIGHT INSIDE
Projection range
ADVANCED MENU
ENGLISH -
67
Settings
FRAME DELAY
When 1 080/60i, 1 080/50i and 1 080/24sF signals are
being input, this simplies image processing so that
the video frame delay is shortened.
Press ▲▼ to select [FRAME DELAY].1 )
Press ◄► to switch [FRAME DELAY].2 )
The setting will change as follows each time
z
◄► is pressed.
DEFAULT SHORT
DEFAULT This is the standard setting.
SHORT
Shortens the delay at the expense of
some picture quality.
Note
When [FRAME DELAY] is set to [SHORT], deterioration
z
in the picture quality will occur. Furthermore, the noise
reduction function cannot be used.
RASTER POSITION
When the scaler is set such that the image is smaller
than the display area, the image can be moved to any
position inside the display area.
Press ▲▼ to select [RASTER 1 )
POSITION].
Press <ENTER> button.2 )
The [RASTER POSITION] screen will be
z
displayed.
Press ▲▼◄► to adjust the position.3 )
DISPLAY LANGUAGE menu
68
- ENGLISH
Settings
DISPLAY LANGUAGE menu
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
Changing the display
language
This lets you switch the on-screen display language.
Menus, setting items, adjustment screens, and
z
control button names will be displayed in the
language the user chooses.
The available languages are: English, German
z
(DEUTSCH), French (FRANÇAIS), Spanish
(ESPAÑOL), Italian (ITALIANO), Japanese
( ), Chinese ( ), Russian (русский), and
Korean ( ).
Note
The on-screen display of the projector is set to the
z
English language on shipping.
DISPLAY LANGUAGE
DISPLAY OPTION menu
ENGLISH -
69
Settings
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
COLOR MATCHING
When multiple sets are used simultaneously, this
projector allows the user to correct the difference of
colors among the sets.
Press ▲▼ to select [COLOR 1 )
MATCHING].
Press ◄► to switch [COLOR 2 )
MATCHING].
The setting will change as follows each time
z
◄► is pressed.
OFF 3COLORS 7COLORS
MEASURED 709MODE
OFF
Color matching adjustment is not
carried out.
3COLORS
It is possible to adjust the 3colors of
[RED], [GREEN] and [BLUE].
7COLORS
It is possible to adjust the 7colors of
[RED], [GREEN], [BLUE], [CYAN],
[MAGENTA], [YELLOW] and
[WHITE].
709MODE
Refer to “
Adjusting the color
matching using a colorimeter” (
Æ
on
this page) for details on this mode.
MEASURED
Refer to “
Adjusting the color
matching using a colorimeter” (
Æ
on
this page) for details on this mode.
If [3COLORS] or [7COLORS] was
J
selected in step 2).
Press <ENTER> button.3 )
The [3COLORS] or [7COLORS] screen will be
z
displayed.
Press ▲▼ to select [RED], [GREEN] 4 )
and [BLUE] (if [7COLORS] was
selected, select [RED], [GREEN],
[BLUE], [CYAN], [MAGENTA],
[YELLOW], and [WHITE]).
Press <ENTER> button.5 )
The [3COLORS:RED], [3COLORS:GREEN] or
z
[3COLORS:BLUE] screen will be displayed.
If you selected [7COLORS], the
[7COLORS:RED], [7COLORS:GREEN],
[7COLORS:BLUE], [7COLORS:CYAN],
[7COLORS:MAGENTA], [7COLORS:YELLOW],
or [7COLORS:WHITE] screen will be displayed.
If [AUTO TEST PATTERN] is turned [ON], the
z
test pattern of the selected color is displayed.
Press ◄► to adjust the values.6 )
These values can be adjusted from 0 (off) to
z
2 048 (full gain).
Note
The effects of correcting the adjustment color:
z
When tuning the correction color that is the same as the
adjustment color: the brightness of the adjustment color
changes.
RED : RED is added to or reduced from the adjustment
color.
GREEN : GREEN is added to or reduced from the
adjustment color.
BLUE : BLUE is added to or reduced from the adjustment
color.
This adjustment should be carried out by a person who is
z
familiar with the projector or by a service person because
a high level of skill is required to make successful
adjustment.
Pressing <DEFAULT> button will restore the factory
z
defaults for all items.
When any setting other than [OFF] has been selected
z
for [COLOR MATCHING], the [COLOR TEMPERATURE]
setting is xed at [USER1].
Adjusting the color matching
J
using a colorimeter
The [RED], [GREEN], [BLUE], [CYAN],
[MAGENTA], [YELLOW] and [WHITE] colors
can be changed to the desired hues using a
colorimeter which is capable of measuring the
chromaticity coordinates and luminance.
Inputting the current luminance and
Q
chromaticity coordinates
Press ▲▼ to select [COLOR 1 )
MATCHING].
Press ◄► to select [709MODE] or 2 )
[MEASURED].
DISPLAY OPTION menu
DISPLAY OPTION menu
70
- ENGLISH
Settings
Press <ENTER> button.3 )
The [
z
709MODE] or [MEASURED MODE]
screen will be displayed.
Press ▲▼ to select [MEASURED 4 )
DATA].
Press <ENTER> button.5 )
The [MEASURED DATA] screen will be
z
displayed.
Use the colorimeter to measure 6 )
the luminance (Y) and chromaticity
coordinates (x, y)
Press ▲▼ to select the colors, and 7 )
press ◄► to select their values.
If [AUTO TEST PATTERN] is turned [ON],
z
the test pattern of the selected color is
displayed.
After all the data has been input, 8 )
press <MENU> button.
The [
z
709MODE] or [MEASURED MODE]
screen will be displayed.
Inputting the coordinates of a desired
Q
color (only [MEASURED])
Press ▲▼ to select [TARGET 9 )
DATA].
Press <ENTER> button.10)
The [TARGET DATA] screen will be
z
displayed.
Press ▲▼ to select the desired 11)
colors, and press ◄► to input
their coordinates.
If [AUTO TEST PATTERN] is turned [ON],
z
the test pattern of the selected color is
displayed.
After all the data has been input, 12 )
press <MENU> button.
Note
If [709MODE] has been selected as the [COLOR
z
MATCHING] setting, the 3 primary colors dened by the
ITU-R BT.709 standard will be set as the target data.
If the target data is outside the color range of the
z
projector, the colors will not be projected correctly.
LARGE SCREEN
CORRECTION
When viewing images close up on a large screen,
you can correct the colors that appear lighter on the
screen so that they appear the same as the colors
that would appear on a normal-sized screen.
Press ▲▼ to select [LARGE SCREEN 1 )
CORRECTION].
Press ◄► to switch [LARGE SCREEN 2 )
CORRECTION].
The setting will change as follows each time
z
◄► is pressed.
OFF (No
correction)
1 (Low) 2 (High)
SCREEN SETTING
(PT-DZ110XE/PT-DS100XE only)
Set this in accordance with the screen you are using.
When the projection image aspect ratio is changed,
the projector makes corrections to ensure the optimal
images for the set screen size.
Press ▲▼ to select [SCREEN 1 )
SETTING].
Press <ENTER> button.2 )
The [SCREEN SETTING] screen will be
z
displayed.
Press ◄► to switch [SCREEN 3 )
FORMAT].
PT-DZ110XE
J
16 : 10 4 : 3 16 : 9
PT-DS100XE
J
4 : 3 16 : 9
DISPLAY OPTION menu
ENGLISH -
71
Settings
Press ◄► to adjust [SCREEN 4 )
POSITION].
In the case of the PT-DZ110XE :
z
When [SCREEN FORMAT] is [16 : 9]
Adjustment range:
-
60 to +60
When [SCREEN FORMAT] is [4 : 3]
Adjustment range:
-
160 to +160
In the case of the PT-DS100XE, you can adjust
z
the setting from
-
132 to +131.
Note
[SCREEN POSITION] cannot be adjusted when
z
[SCREEN FORMAT] is [16 : 10] (PT-DZ110XE) or [4 : 3]
(PT-DS100XE).
WAVEFORM MONITOR
(PT-DZ110XE only)
This function displays the waveform of the input signal
from a connected peripheral device.
You can check if the image output (BRIGHTNESS)
signal level is within the range recommended by this
projector and adjust it as necessary.
Press ▲▼ to select [WAVEFORM 1 )
MONITOR].
Press ◄► to switch [WAVEFORM 2 )
MONITOR].
The setting will change as follows each time
z
◄► is pressed.
OFF ON
Press the <MENU> button twice to turn 3 )
off the menu screen.
Select any horizontal line with the ▲▼.4 )
Line selection
(BRIGHTNRSS)
Line selection
(RED)
Line selection
(BLUE)
Line selection
(GREEN)
Note
Setting can also be performed using the <FUNCTION>
z
button. (
Æ
page 85)
Adjust the waveform
J
Project the brightness adjustment signal from, for
example, a commercially available adjustment disc
(0% [0 IRE or 7.5 IRE] - 100 % [100 IRE]) and adjust
the waveform.
Adjusting brightness
Q
Select [Line selection (BRIGHTNRSS)] 1 )
in the waveform monitor.
Adjust the black level.2 )
In [BRIGHTNESS] of on-screen menu
z
[PICTURE], adjust the 0 % of the black level of
the image signal to the position corresponding
to 0% on the waveform monitor.
Adjust the white level.3 )
In [CONTRAST] of on-screen menu [PICTURE],
z
adjust the 100 % of the while level of the image
signal to the position corresponding to 100 %
on the waveform monitor.
Adjusting RED, GREEN, and BLUE
Q
Set [COLOR TEMPERATURE] to 1 )
[USER1] or [USER2]. (
Æ
page 55)
Select [Line selection (RED)] in the 2 )
waveform monitor.
Adjust the dark portion of RED.3 )
In [RED] of [WHITE BALANCE LOW], adjust
z
the 0 % of the black level of the image signal
to the position corresponding to 0 % on the
waveform monitor. (
Æ
page 55)
Image
displayable
area
Monitor position
0%
50%
100%
Signal level
DISPLAY OPTION menu
72
- ENGLISH
Settings
Adjust the light portion of RED.4 )
In [RED] of [WHITE BALANCE HIGH], adjust
z
the 100 % of the white level of the image signal
to the position corresponding to 100 % on the
waveform monitor. (
Æ
page 55)
Adjust [GREEN] and [BLUE] in a 5 )
similar manner.
Note
When the DVI-D signal, HDMI signal, or SDI signal is
z
inputted, check that the [DVI SIGNAL LEVEL], [HDMI
SIGNAL LEVEL], and [SDI SIGNAL LEVEL] are correctly
set before adjusting the black level.
The keystone cannot be applied to the waveform monitor
z
display.
The waveform monitor cannot be displayed in the [P IN P]
z
mode.
If the [P IN P] mode is set while the waveform is being
z
monitored, the waveform monitor will turn off.
The waveform monitor is not displayed while the on-
z
screen display is off.
AUTO SIGNAL
You can turn ON/OFF automatically detecting system
of the AUTO SETUP feature.
Press ▲▼ to select [AUTO SIGNAL].1 )
Press ◄► to switch [AUTO SIGNAL].2 )
The setting will change as follows each time
z
◄► is pressed.
OFF ON
OFF
Only when <AUTO SETUP> button
is pressed, the projected image
position will be adjusted.
ON
If unregistered signals are input
when [ON] is selected, auto setup
will be initiated automatically.
AUTO SETUP
Use this setting when adjusting a specic or oblong
(16:9, etc.) signal.
Press ▲▼ to select [AUTO SETUP].1 )
Press <ENTER> button.2 )
The [AUTO SETUP] screen will be displayed.
z
Press ▲▼ to select [MODE].3 )
Press ◄► to switch [MODE].4 )
The setting will change as follows each time
z
◄► is pressed.
DEFAULT WIDE USER
DEFAULT
To receive signals of which image
aspect is 4:3 or 5:4
(applicable resolution : 640 × 400,
640 × 480, 800 × 600, 832 × 624,
960 × 720, 1 024 × 768,
1 152 × 864, 1 152 × 870,
1 280 × 960, 1 280 × 1 024,
1 600 × 1 200, 1 400 × 1 050)
WIDE
To receive signals of which the
image aspect is wide
(applicable resolution: 720 × 400,
848 × 480, 1 280 × 720,
1 024 × 600, 1 120 × 750,
1 440 × 900, 1 680 × 1 050)
USER
To receive signals of specic
horizontal resolution (number of
horizontally displayed dots)
If [USER] is selected, press ◄► to 5 )
enter the horizontal resolution of
signal source into [DISPLAY DOTS].
Press <ENTER> button.6 )
Execute automatic adjustment. A message
z
“PROGRESS...” appears during automatic
adjustment. When the adjustment is complete,
the system returns to the input screen.
DISPLAY OPTION menu
ENGLISH -
73
Settings
Adjusting the position
J
automatically
Select [POSITION ADJUST] in step 3).1.
Press ◄► to switch [POSITION 2.
ADJUST].
The setting will change as follows each time
z
◄► is pressed.
OFF ON
OFF Automatic adjustment is off.
ON
Screen position and size are
adjusted during AUTO SETUP
operation.
Adjusting the signal level
J
automatically
Select [SIGNAL LEVEL ADJUST] in 1.
step 3).
Press ◄► to switch [SIGNAL LEVEL 2.
ADJUST].
The setting will change as follows each time
z
◄► is pressed.
OFF ON
OFF Automatic adjustment is off.
ON
The black level (On-screen menu
[BRIGHTNESS]) and white level
(On-screen menu [CONTRAST])
are adjusted during AUTO SETUP
operation.
Note
If the input image is not a still image with a clear
z
difference between black and white, the [SIGNAL LEVEL
ADJUST] function may not operate normally.
RGB IN
(Only RGB input)
Change this setting to change the input impedance of
the synchronous signal input.
Press ▲▼ to select [RGB IN].1 )
Press <ENTER> button.2 )
The [
z
RGB IN] screen will be displayed.
Press ▲▼ to select [RGB1 SYNC 3 )
TERMINAL] or [RGB2 SYNC
TERMINAL].
Press ◄► to switch.4 )
The setting will change as follows each time
z
◄► is pressed.
LOW HIGH
LOW Input impedance is set to [LOW].
HIGH Input impedance is set to [HIGH].
DVI-D IN
Change this setting if video does not display normally
when the projector and an external device are
connected via DVI.
Press ▲▼ to select [DVI-D IN].1 )
Press <ENTER> button.2 )
The [
z
DVI-D IN] screen will be displayed.
Press ▲▼ to select [DVI EDID].3 )
Press ◄► to switch [DVI EDID].4 )
The setting will change as follows each time
z
◄► is pressed.
EDID3 EDID1 EDID2 : PC
EDID3
Switch between ne settings for a
moving image and for a still image.
EDID1
Mainly select this when an external
device (DVD player, etc.) for
outputting video signals of a moving
image system is connected to DVI-D
IN.
EDID2 : PC
Mainly use this when an external
device (PC, etc.) for outputting video
signals of a still image system is
connected to DVI-D IN.
Press ▲▼ to select [DVI SIGNAL 5 )
LEVEL].
DISPLAY OPTION menu
74
- ENGLISH
Settings
Press ◄► to switch [DVI SIGNAL 6 )
LEVEL].
The setting will change as follows each time
z
◄► is pressed.
0-255 : PC 16-235
0-255 : PC
Select this when, for example,
an external device (PC, etc.) is
connected via the DVI terminal
output.
16-235
Select this when, for example, an
external device (DVD player, etc.)
is connected via the HDMI terminal
output using a conversion cable.
Note
The optimal setting differs depending on the output
z
setting of the connected external device. Refer to the
instruction manual of the external device.
If the setting is changed, the data for plug and play
z
changes. For the plug and play compatible resolutions,
refer to “List of compatible signals” (
Æ
page 123).
HDMI IN
Change this setting if video does not display normally
when the projector and an external device are
connected via HDMI.
Press ▲▼ to select [HDMI IN].1 )
Press <ENTER> button.2 )
The [
z
HDMI IN] screen will be displayed.
Press ◄► to switch [HDMI SIGNAL 3 )
LEVEL].
The setting will change as follows each time
z
◄► is pressed.
0-1023 64-940
0-1023
Select this when, for example, a DVI
terminal output of an external device
(PC etc.) is connected to HDMI IN
using a conversion cable, etc.
64-940
Select this when, for example,
an HDMI terminal output of an
external device (DVD player, etc.) is
connected to HDMI IN.
Note
The optimal setting differs depending on the output
z
setting of the connected external device. Refer to the
instruction manual for the external device.
The displayed HDMI signal level is the value when the
z
input is 30 bit.
SDI IN
(PT-DZ110XE/PT-DS100XE only)
You can select signal amplitude type.
Available with YP
B
P
R
or RGB of HD-SDI signal.
Press ▲▼ to select [SDI IN].1 )
Press <ENTER> button.2 )
The [
z
SDI IN] screen will be displayed.
Press ◄► to switch [SDI SIGNAL 3 )
LEVEL].
The setting will change as follows each time
z
◄► is pressed.
64-940 4-1019
64-940 Normal setting
4-1019
For when grey color is too close to
black
ON-SCREEN DISPLAY
The user can specify the on-screen display.
Press ▲▼ to select [ON-SCREEN 1 )
DISPLAY].
Press <ENTER> button.2 )
The [ON-SCREEN DISPLAY] screen will be
z
displayed.
Press ▲▼ to select the desired item, 3 )
and press ◄► to change the setting.
OSD POSITION
J
This sets the position of the on-screen display
(OSD).
2 (Left center
of the screen)
3 (Bottom left
of the screen)
4 (Top center
of the screen)
1 (Top left
of the screen)
5 (Center
of the screen)
9 (Bottom right
of the screen)
6 (Bottom center
of the screen)
8 (Right center
of the screen)
7 (Top right
of the screen)
DISPLAY OPTION menu
ENGLISH -
75
Settings
OSD DESIGN
J
This sets the color of the on-screen display (OSD).
1 : Yellow 2 : Blue
6 : Brown 3 : White
5 : Pink 4 : Green
OSD MEMORY
J
The current menu cursor position will be retained
temporarily unless the projector switched off.
ON OFF
INPUT GUIDE
J
This sets whether to display the currently
selected input guide at the position set for [OSD
POSITION].
ON OFF
WARNING MESSAGE
J
This sets the display of warning messages.
ON OFF
BACK COLOR
This sets the color for the projection screen when no
signals are being input.
Press ▲▼ to select [BACK COLOR].1 )
Press ◄► to switch [BACK COLOR].2 )
The setting will change as follows each time
z
◄► is pressed.
BLUE BLACK
LOGO2 LOGO1
BLUE
The entire projection area will
appear blue.
BLACK
The entire projection area will
appear black.
LOGO1
The picture registered by the user
will be projected in the projection
area.
LOGO2 The Panasonic logo is projected.
Note
Separate software is required in order to create the
z
pictures to use for [LOGO1]. Consult your dealer.
STARTUP LOGO
This sets the startup logo that is projected when the
power is turned on.
Press ▲▼ to select [STARTUP LOGO].1 )
Press ◄► to switch [STARTUP LOGO].2 )
The setting will change as follows each time
z
◄► is pressed.
LOGO2 NONE LOGO1
LOGO2 The Panasonic logo is projected.
NONE No startup logo is projected.
LOGO1
The picture registered by the user
will be projected.
Note
Separate software is required in order to create the
z
pictures to use for [LOGO1]. Consult your dealer.
STARTUP LOGO will be displayed for 15 seconds.
z
FREEZE
You can freeze the projected image and stop the
sound temporarily, regardless of the playing condition
of the connected device.
Press ▲▼ to select [FREEZE].1 )
Press <ENTER> button.2 )
Press <MENU> button to escape.
z
PROJECTOR SETUP menu
76
- ENGLISH
Settings
PROJECTOR SETUP menu
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
PROJECTOR ID
The projector has an ID number setting function that
helps the user to control two or more projectors either
simultaneously or separately with a single remote
control.
Press ▲▼ to select [PROJECTOR ID].1 )
Press ◄► to switch [PROJECTOR ID].2 )
The setting will change as follows each time
z
◄► is pressed.
ALL 1
64 2
Note
The ID number can be set to [ALL], or selected from [1]
z
to [64].
If the projectors are given ID numbers, their remote
z
controls must be assigned the same ID numbers,
respectively.
If the ID number of a projector is set to [ALL], it can be
z
controlled by the remote control or the PC with any ID
number.
If multiple projectors are used and some of them
have their IDs set to “ALL”, they cannot be controlled
separately from the projectors with other ID numbers.
For details on remote control ID setting, refer to “Setting
projector ID number to remote control” (
Æ
page 21).
INSTALLATION
A projection scheme can be chosen depending on
the installation of the projector. If the picture is shown
upside down or in reverse, change the projection
scheme.
Select the setting by displaying the on-screen
z
indications using buttons of the remote control or
the control panel on the main unit.
Press ▲▼ to select [INSTALLATION].1 )
Press ◄► to switch [INSTALLATION].2 )
The setting will change as follows each time
z
◄► is pressed.
FRONT/FLOOR FRONT/CEILING
REAR/CEILING REAR/FLOOR
FRONT/
FLOOR
Setting on a desk/oor and
projecting from front
FRONT/
CEILING
Mounting on the ceiling and
projecting from front
REAR/
FLOOR
Setting on a desk/oor and
projecting from rear
REAR/
CEILING
Mounting on the ceiling and
projecting from rear
HIGH ALTITUDE MODE
If you use the projector at high elevation (1 400 m to
2 700 m), the [HIGH ALTITUDE MODE] setting needs
to be [ON] to set the fan speed high.
Press ▲▼ to select [HIGH ALTITUDE 1 )
MODE].
Press ◄► to switch [HIGH ALTITUDE 2 )
MODE] and press <ENTER> to select.
The setting will change as follows each time
z
◄► is pressed.
OFF ON
OFF
Select this when using in normal
environment (less than 1 400 m
above sea level)
ON
Select this when using at high
altitude (above 1 400 m and less
than 2 700 m above sea level)
When the conrmation message is 3 )
displayed, select [OK] or [CANCEL].
Note
The loudness of fan noise depends on the [HIGH
z
ALTITUDE MODE] setting.
The separately-sold Smoke Cut Filter cannot be used
z
when the [HIGH ALTITUDE MODE] is [ON].
PROJECTOR SETUP menu
ENGLISH -
77
Settings
COOLING CONDITION
You can control the fan speed for projecting
angle. When the projector is angled, [COOLING
CONDITION] setting must be set correctly. Failure to
observe this may result in malfunctions, or the life of
the lamp or the other components may be shortened.
Press ▲▼ to select [COOLING 1 )
CONDITION].
Press <ENTER> button.2 )
The [COOLING CONDITION] screen will be
z
displayed.
Press ▲▼ to select cooling condition.3 )
Press <ENTER> button.4 )
When the conrmation message is 5 )
displayed, select [OK] or [CANCEL].
LAMP SELECT
You can select a lamp lighting pattern for using
environment.
Press ▲▼ to select [LAMP SELECT].1 )
Press ◄► to switch [LAMP SELECT].2 )
The setting will change as follows each time
z
◄► is pressed.
DUAL SINGLE
LAMP2 LAMP1
DUAL All lamps will light.
SINGLE
Selects a lamp with shorter duration
of use.
LAMP1 Selects the Lamp unit 1.
LAMP2 Selects the Lamp unit 2.
Press <ENTER> button.3 )
Note
If, in the [SINGLE], [LAMP1] or [LAMP2] mode, one lamp
z
remains off or the currently active lamp exceeds 3 000
hours of cumulative operating time (when [HIGH] is
selected as the [LAMP POWER] setting), the other lamp
will light.
If, in the [DUAL] mode, one lamp remains off or the
currently active lamp exceeds 3 000 hours of cumulative
operating time (when [HIGH] is selected as the [LAMP
POWER] setting), the other lamp alone will light.
However, if both lamps remain off or the 3 000 hours of
cumulative operating time (when [HIGH] is selected as
the [LAMP POWER] setting) are exceeded, the projector
will enter the standby mode.
The colors of the items indicate the status.
z
Green→Current setting
Yellow→Current setting
(when a lamp fails or fails to light)
Red→Lamp that has failed to light
White→Any other status
If the projector is repeatedly used for short periods of
z
time, the lamps will need to be replaced more frequently.
LAMP RELAY
If using the projector for a continuous period of
24 hours or more, this setting can be used to
automatically switch the lamps that are turned on in
order to reduce the lamp deterioration that can occur
as a result of continuous use.
Press ▲▼ to select [LAMP RELAY].1 )
Press <ENTER> button.2 )
The [LAMP RELAY] screen is displayed and the
z
adjustment mode (ashing) is activated.
Press ◄► to select [HOUR] or 3 )
[MINUTE] and use ▲▼ to adjust the
time.
Press <ENTER> button.4 )
The lamp relay is set to the selected time.
z
OFF
Û
00 : 00
00 : 59 00 : 01
When setting the [MINUTE], irrespective of the :
Û
set value for [HOUR], please adjust and set in the
following order of 59 minutes, [OFF], 00 minutes.
CEILING
SETTING
30°
30°
VERTICAL DOWN
SETTING
30°
30°
VERTICAL UP
SETTING
FLOOR
SETTING
(Unit: 1 hour or
1 minute)
PROJECTOR SETUP menu
78
- ENGLISH
Settings
Note
Only when [DUAL] or [SINGLE] is selected in [LAMP
z
SELECT], [LAMP RELAY] is available
If [DUAL] is selected in [LAMP SELECT], only one lamp
z
is turned on for four hours after the set time.
The setting time will be the local time.
z
(
Æ
page 85)
The time can be input directly using the numeral keys on
z
the remote control.
If the lter is running low, only one lamp will light even
z
when [DUAL] is selected. The lamps will light as normal
once the lter has been replaced and the residual lter
has been reset.
LAMP POWER
The luminance of the projection lamp can be changed
depending on user’s needs or the viewing conditions.
Press ▲▼ to select [LAMP POWER].1 )
Press ◄► to switch [LAMP POWER].2 )
The setting will change as follows each time
z
◄► is pressed.
HIGH LOW
HIGH
Set when high brightness is
necessary.
LOW
Set when high brightness is not
necessary.
Note
When set to [LOW], it is possible to reduce power
z
consumption, reduce operating noise and extend lamp
service life.
BRIGHTNESS CONTROL
This projector has a built-in brightness sensor
for measuring the lamp power and a function for
correcting the screen brightness according to the
change in lamp power.
With this function, you can reduce changes in
brightness caused by aging of the lamps when
multiple screens are projected using multiple
projectors, or minimize any uctuations in brightness.
BRIGHTNESS CONTROL GAIN
J
This function is used to adjust the brightness
when multiple screens are projected using multiple
projectors.
Press ▲▼ to select [BRIGHTNESS 1 )
CONTROL GAIN].
Press ◄► to adjust.2 )
Operation
Adjustment
Adjustment
range
Brightness
Max. quantity
of brightness
control
Press ►. Increases Decreases
Maximum
value 100 %
Press ◄. Decreases Increases
Minimum
value 20 %
Note
When using one projector, the maximum quantity of
z
brightness control is obtained by subtracting the value
of [BRIGHTNESS CONTROL GAIN] from 100 %. If the
[BRIGHTNESS CONTROL GAIN] is set to 100 %, the
maximum quantity of control is 0 % and the brightness
cannot be corrected using the brightness control function.
The brightness will not stabilize for 8 minutes after the
z
lamp is turned on. Make adjustments after at least eight
minutes has elapsed after the power is turned on.
The adjustment in [BRIGHTNESS CONTROL GAIN]
z
will be reected in all of the image signals, internal test
pattern, and on-screen menu.
[BRIGHTNESS CONTROL GAIN] remains effective even
z
if [BRIGHTNESS CONTROL SETUP] is [OFF].
BRIGHTNESS CONTROL SETUP
J
This function is used to set the operation of the
brightness control.
Press ▲▼ to select [BRIGHTNESS 1 )
CONTROL SETUP].
Press <ENTER> button.2 )
The [BRIGHTNESS CONTROL SETUP] screen
z
will be displayed.
Press ▲▼ to select [MODE].3 )
Press ◄► to switch [MODE].4 )
The setting will change as follows each time
z
◄► is pressed.
OFF AUTO PC
OFF
Brightness correction with the
brightness sensor is not performed.
AUTO
Brightness is corrected with the
brightness sensor. If lamp power
changes, screen brightness will correct
automatically.
PC
Nine or more projectors are operated
simultaneously using a computer and
the [Multi Projector Monitoring & Control
Software].
PROJECTOR SETUP menu
ENGLISH -
79
Settings
When [MODE] is set to [AUTO]
Q
Press ▲▼ to select [LINK].5 )
Press ◄► to switch [LINK].6 )
The setting will change as follows each time
z
◄► is pressed.
OFF GROUP A
GROUP D GROUP C GROUP B
OFF
Brightness is corrected using the
brightness sensor of one of the
projectors, without linking with other
projectors.
A smaller [BRIGHTNESS CONTROL
GAIN] value means the constant
brightness can be maintained for longer.
GROUP
A - D
Brightness is corrected using brightness
sensors of multiple projectors linked
with each other.
Up to 4 groups from A to D can be set
within the same sub-network using
the network function that links multiple
projectors.
Up to 8 projectors can be registered in
1 group and linked with each other.
Press ▲▼ to select [APPLY].7 )
Press <ENTER> button.8 )
The selected [MODE] and [LINK] are activated,
z
then the [BRIGHTNESS CONTROL STATUS]
screen will be displayed.
If <ENTER> button is pressed while [MODE] of
z
the brightness control is not switched to [OFF],
the lamp power at the time is saved as the
reference power.
If <ENTER> button is pressed while [LINK] is
z
[GROUP A - D], the group name is displayed on
the screens of the projectors that are set in the
same group.
Note
When setting [MODE] of the brightness control to [AUTO]
z
or [PC], execute brightness control with the shutter open
for at least 2 minutes.
If the shutter is closed within about 10 minutes after
z
the lamp is turned on while the brightness control is set
to [MODE], [AUTO], or [PC], the brightness cannot be
measured. In this case, the brightness may be corrected
about 2 minutes after the shutter is opened.
While [MODE] of the brightness control is set to [AUTO]
z
or [PC], the [DYNAMIC IRIS] function is kept [OFF (No
correction)].
While [MODE] of the brightness control is set to [AUTO]
z
or [PC], the [LAMP POWER] is xed to [HIGH] or [LOW].
When changing the lamp power, return [MODE] of the
brightness control to [OFF], then change the lamp power
and adjust the brightness control again.
While [MODE] of the brightness control is set to [AUTO]
z
or [PC], the lamp power is measured automatically
about 8 minutes after the lamp is turned on and then
corrected so that the screen brightness will be the same
as the reference brightness when the brightness control
is executed. The lamp power is not measured for about
8 minutes after the lamp is turned on as it does not
stabilize within this period.
While [MODE] of the brightness control is set to [AUTO],
z
if the lamp is kept on for more than 25 hours, the
brightness is corrected automatically every 25 hours.
While [LAMP SELECT] is set to [DUAL] and [MODE]
z
is set to [AUTO], if the lamp goes off, the brightness is
corrected as much as possible about 1 minute after.
While [MODE] of the brightness control is set to [AUTO]
z
and [LINK] is set to [OFF], the brightness is corrected
until the maximum quantity of correction is achieved.
The brightness may be dispersed largely because of dust
z
sticking to the lens, screen, or inside of the projector,
depending on the environment in which the projector has
been installed.
If the brightness uctuates signicantly because of aging
z
of the lamp or if the lamp has been replaced, re-adjust
the brightness control.
BRIGHTNESS CONTROL STATUS
J
This function displays the status of the brightness
control.
Press ▲▼ to select [BRIGHTNESS 1 )
CONTROL STATUS].
Press <ENTER> button.2 )
The [BRIGHTNESS CONTROL STATUS]
z
screen will be displayed.
LINK GROUP A
PROJECTOR SETUP menu
80
- ENGLISH
Settings
When [MODE] of brightness control is
Q
[OFF]
The state that the brightness control is OFF is
displayed.
The name of this projector is displayed.
When [MODE] of brightness control is
Q
[AUTO] and [LINK] is [OFF]
The state that the LINK is OFF is displayed.
The name of this projector is displayed.
The state is indicated by color.
GREEN : The brightness can be corrected by a
signicant margin.
YELLOW : The brightness can no longer be
corrected by a signicant margin.
RED : There is an error in brightness control.
When [MODE] of brightness control
Q
is set to [AUTO] and [LINK] is set to
[GROUP A - D]
The brightness control of up to 8 projectors linked
with each other, including the projector operated
using the on-screen menu, is displayed.
The group to be linked is displayed.
The name and IP address of this projector are
displayed.
The projector name and IP address of the
same group detected through the network are
displayed.
The state is indicated by color.
GREEN : The brightness can be corrected by a
signicant margin.
YELLOW : The brightness can no longer be
corrected by a signicant margin.
RED : There is an error in brightness control.
An error message is displayed.
The information is updated.
If the message of [Failed to apply BRIGHTNESS
CONTROL to some projectors.] is displayed, the
projectors indicated in red are not linked.
Press ▲▼ to select a projector indicated in red,
then press <ENTER> button to display the details
of the error.
RETURN
MENU
MODE OFF
PROJECTOR2
BRIGHTNESS CONTROL STATUS
RETURN
MENU
LINK OFF
PROJECTOR2
BRIGHTNESS CONTROL STATUS
MENU SELECT
LINK GROUP A
PROJECTOR2 192.168. 0. 9
1: PROJECTOR1 192.168. 0. 8
2: PROJECTOR3 192.168. 0. 10
3:
4:
5:
6:
7:
UPDATE
BRIGHTNESS CONTROL STATUS
PROJECTOR SETUP menu
ENGLISH -
81
Settings
Details of error
z
Error message Remedial measure
[Exceed maximum
number of projectors.]
Limit number of
projectors in same group
to 8.
When linking 9 or
more projectors, use a
computer and the [Multi
Projector Monitoring &
Control Software].
[Please check the
COMMAND CONTROL
setting.]
Turn [ON] the
[COMMAND CONTROL]
on the on-screen menu
[NETWORK CONTROL]
for the projector with the
error display.
Set [COMMAND
PORT] of [NETWORK
CONTROL] of all linked
projectors to the same
value.
[Please check the
USER NAME and
PASSWORD in the
COMMAND CONTROL
setting.]
Set the [USER NAME]
and [PASSWORD] for the
administrator authority for
[WEB CONTROL] of all
the linked projectors to
the same text string.
[Cannot apply
BRIGHTNESS
CONTROL. Please
check projector status.]
Projector is in standby
state. Turn on power.
[Brightness Sensor
Error]
There is a fault in the
brightness sensor. If the
fault is not corrected by
turning the power off and
back on, consult your
dealer.
Note
If the linked projectors are not listed, check the following.
z
The devices on the network all have different IP
addresses.
The LAN cable is connected correctly.
(
Æ
page 96)
The sub-nets of the projectors are the same.
The [LINKS] are set in the same group.
For changing the projector name, refer to
z
“NETWORK
SETUP” of “NETWORK menu” (
Æ
page 95) or “
Network
cong page” (
Æ
page 107).
When [MODE] of brightness control is
Q
set to [PC]
The name of this projector is displayed.
The state is indicated by color.
GREEN : The brightness can be corrected by a
signicant margin.
YELLOW : The brightness can no longer be
corrected by a signicant margin.
RED : There is an error in brightness control.
Example of adjustment procedure
J
for brightness control
The following is an example of adjustment procedure
for linking the brightness of 8 projectors that form a
network.
Connect all the projectors to the hub 1 )
using the LAN cables. (
Æ
page 96)
Turn on the power in all projectors.2 )
Ensure [LAMP SELECT] of all the 3 )
projectors are either all set to [DUAL]
or all set to [SINGLE].
Set [MODE] of [BRIGHTNESS 4 )
CONTROL SETUP] to [OFF], and
select [APPLY].
Set [SUBNET MASK] of all the 5 )
projectors to the same value and set
their [IP ADDRESS] to different values
so that network communication can
be performed.
Wait at least 8 minutes until the lamp 6 )
power stabilizes.
Set all the items in the [PICTURE] 7 )
menu of all the projectors to the same
value.
To match the color, adjust [COLOR 8 )
MATCHING].
RETURN
MENU
MODE PC
PROJECTOR2
BRIGHTNESS CONTROL STATUS
PROJECTOR SETUP menu
82
- ENGLISH
Settings
Display the internal test pattern [ALL 9 )
WHITE] on all projectors.
Set [BRIGHTNESS CONTROL GAIN] 10)
of all projectors to 100 %.
Set [BRIGHTNESS CONTROL GAIN] 11)
of the darkest projector to 90 %.
Adjust [BRIGHTNESS CONTROL 12)
GAIN] of the other projectors to that
of the projector that was set to 90 %.
Set [MODE] of [BRIGHTNESS 13)
CONTROL SETUP] of all projectors to
[AUTO] and set [LINK] to [GROUP A].
[APPLY] [BRIGHTNESS CONTROL 14)
SETUP] of all projectors and press
<ENTER> button.
Brightness control will commence.
z
Note
The brightness is corrected automatically each time the
z
lamps are turned on using the power switch etc.
If the brightness uctuates signicantly or the lamp has
z
been replaced, re-adjust the brightness control.
STANDBY MODE
You can select the electrical consumption while in
standby mode.
Press ▲▼ to select [STANDBY MODE].1 )
Press ◄► to switch [STANDBY 2 )
MODE].
The setting will change as follows each time
z
◄► is pressed.
NORMAL ECO
Note
With [ECO] setting, NETWORK function, RS-232C output
z
and some of RS-232C commands are not available.
When switch on the projector, projection will start about
10 seconds late.
SCHEDULE
This sets the command execution schedule for each
day of the week.
How to enable the SCHEDULE
J
function
Press ▲▼ to select [SCHEDULE].1 )
Press ◄► to switch [SCHEDULE].2 )
The setting will change as follows each time
z
◄► is pressed.
ON OFF
Note
If [SCHEDULE] is set to [ON], the setting for [STANDBY
z
MODE] is automatically set to [NORMAL] and cannot be
changed. Even if [SCHEDULE] is then set to [OFF] when
in this state, the setting of [STANDBY MODE] remains at
[NORMAL].
How to assign a program
J
With [SCHEDULE] switched to [ON], 1 )
press <ENTER> button.
The [SCHEDULE] screen will be displayed.
z
Select and assign program to each day 2 )
of week.
Press ▲▼ to select a day of week and press
z
◄► to select a program number.
You can set the program from No.1 to No.7.
z
“- - -” indicates that the program number has
not been set yet.
How to set a program
J
You can set up to 16 commands to each program.
On the [SCHEDULE] screen, press ▲▼ 1 )
to select [PROGRAM EDIT].
Press ◄► to select a program number 2 )
to be set and press <ENTER> button.
Press ▲▼ to select a command 3 )
number and press <ENTER> button.
You can change the page using ◄►.
z
PROJECTOR SETUP menu
ENGLISH -
83
Settings
Press ▲▼ to select [TIME] or 4 )
[COMMAND] and change the setting
according to the instructions of the
menu.
TIME
Set the time at which the command
will be executed using ▲▼ or numeral
buttons.
COMMAND
Select a command to execute at the
set time from the following.
POWER ON
STANDBY
SHUTTER
OPEN
SHUTTER
CLOSE
INPUT RGB1
INPUT RGB2
INPUT VIDEO
INPUT S-VIDEO
INPUT DVI-D
INPUT HDMI
INPUT SDI
Û
LAMP POWER
HIGH
LAMP POWER
LOW
LAMP DUAL
LAMP SINGLE
P IN P OFF
P IN P USER1
P IN P USER2
P IN P USER3
PT-DZ110XE/PT-DS100XE only:
Û
Press ▲▼ to select [STORE] and 5 )
press <ENTER> button.
Note
If you try to register a setting that would cause the
z
lamp to ash for a short time, an error message will be
displayed on the screen. Set the [TIME] and [COMMAND]
again.
To delete a command which has been set, press
z
<DEFAULT> button.
If multiple commands have been set for the same time,
z
they are executed in chronological order starting from the
smallest command number.
The setting time operates under the local time.
z
(
Æ
page 85)
If an operation is executed with the remote control or
z
control panel of the projector or with a control command
before the command set in the schedule is executed, the
command set with this function may not be executed.
RS-232C
This sets the communication parameters at the serial
terminals.
Press ▲▼ to select [RS-232C].1 )
Press <ENTER> button.2 )
The [
z
RS-232C] screen will be displayed.
Press ▲▼ to select communication 3 )
conditions.
press ◄► to change the setting.4 )
Note
Refer to “Serial terminal” (
z
Æ
page 118).
Selecting items in [EMULATE]
J
When using the control commands for one of our
projectors that you have previously purchased to
control this projector using a computer via its serial
input terminal, set up the EMULATE function as
follows. This will allow you to use the control software
etc. designed for our existing projectors.
Select [EMULATE] in step 3).1.
Press <ENTER> button.2.
Press ▲▼ to select the required item.3.
Press <ENTER> button.4.
DEFAULT
DZ110XE Series, DS100XE Series,
DW90XE Series, D5000 Series,
D6000 Series, DW6300 Series,
DZ6700 Series, DZ6710 Series
D9610
SERIES
D9510 Series, D9610 Series,
D9500 Series, D9600 Series,
D8500 Series, D8600 Series
D7700
SERIES
D7500 Series, D7600 Series,
D7700 Series, DW7000 Series
L6500
SERIES
L6500 Series, L6510 Series,
L6600 Series
About [EMULATE SETTING]
J
This sets which input signal can be selected using the
input signal change command when a projector of a
specic model is used with the emulate function.
Select [EMULATE SETTING] in step 3).1.
Press <ENTER> button.2.
The [EMULATE SETTING] screen will be
z
displayed.
When the D9610 Series is selected
Q
Press ▲▼ to select input signal 1.
[VIDEO], [S-VIDEO], [RGB1], [DVI-D] or
[SDI].
[RGB2] and [HDMI] cannot be selected.
z
[SDI] is not shown for PT-DW90XE.
z
Press ◄► to select the input signal 2.
change command to be assigned to
the selected input signal.
Selectable input signal change commands
z
When RGB1 is selected:
[INPUT1], [INPUT2], [INPUT3], [INPUT
RGB], [NONE]
For all other instances:
[INPUT1], [INPUT2], [INPUT3], [NONE]
The same input signal change command
z
cannot be assigned to multiple input signals.
PROJECTOR SETUP menu
84
- ENGLISH
Settings
When the D7700 Series is selected
Q
Press ▲▼ to select input signal 1.
[DVI-D] or [SDI].
[RGB1], [RGB2], [VIDEO], [S-VIDEO] and
z
[HDMI] cannot be selected.
Since [RGB1], [RGB2], [VIDEO], and [S-VIDEO]
are already installed on the projector, another
input signal change command cannot be
assigned.
[SDI] is not shown for PT-DW90XE.
z
Press ◄► to select the input signal 2.
change command to be assigned to
the selected input signal.
The signal change command can be selected
z
to either [AUX] or [NONE].
The same input signal change command
z
cannot be assigned to both [DVI-D] and [SDI].
STATUS
Displays the status of the projector.
Press ▲▼ to select [STATUS].1 )
Press <ENTER> button.2 )
Press ◄► to move to the next page.3 )
INPUT
Displays the input selection
state.
SIGNAL NAME Displays the input signal name.
SIGNAL
FREQUENCY
Displays the frequency of the
input signal.
PROJECTOR
RUNTIME
Displays the projector runtime.
LAMP1
*1
Displays the lighting time of
LAMP1.
LAMP2
*1
Displays the lighting time of
LAMP2.
INTAKE
AIR TEMP.
Displays the intake air
temperature of the projector.
OPTICS
MODULE TEMP.
Displays the temperature inside
the projector.
AROUND
LAMP TEMP.
Displays the temperature around
the lamp of the projector.
REMAINING
FILTER
QUANTITY
*2
Displays the lter remaining
quantity.
PROJECTOR
TYPE
Displays type of projector.
SERIAL
NUMBER
Displays the serial number of the
projector.
LAMP UNIT
MODEL NO.
Displays the component number
of the lamp unit.
LAMP1 SERIAL
NUMBER
Displays the serial number for
lamp1.
LAMP2 SERIAL
NUMBER
Displays the serial number for
lamp2.
MAIN VERSION
Displays the main version of the
rmware of the projector unit.
SUB VERSION
Displays the sub version of the
rmware of the projector unit.
NETWORK
VERSION
Displays the network version of
the projector unit.
EMULATE Displays the set emulate mode.
ON COUNT
POWER ON TIMES :
z
Displays the number of times
the power has been turned
on.
LAMP1 ON :
z
Displays the number of times
LAMP1 has been lit.
LAMP2 ON :
z
Displays the number of times
LAMP2 has been lit.
LAMP1
Displays the lighting time of
LAMP1. (HIGH or LOW)
LAMP2
Displays the lighting time of
LAMP2. (HIGH or LOW)
NUMBER OF
ENTRY SIGNAL
Displays the number of
registered signals.
REMOTE2
STATUS
Displays [REMOTE 2 IN] control
status.
AC VOLTAGE Displays the AC voltage state.
*1 :
Lamp replacement time =
LAMP POWER [HIGH] lighting time +
(LAMP POWER [LOW] lighting time x 3 ÷ 4)
REMAINING FILTER QUANTITY*2 :
If the remaining quantity of ACF becomes 8%,
the status display turns yellow. If the remaining
quantity becomes 0%, the display turns red.
If the residual lter indication becomes yellow,
the remaining usable time is about 200 hours.
The time of 200 hours is for reference only. It
depends on the usage environment.
PROJECTOR SETUP menu
ENGLISH -
85
Settings
NO SIGNAL SHUT-OFF
You can set the timer to switch off the power of the
projector after a certain period of time automatically
when no signal is detected.
Press ▲▼ to select [NO SIGNAL 1 )
SHUT-OFF].
Press ◄► to switch [NO SIGNAL 2 )
SHUT-OFF].
DISABLE
Deactivate the NO SIGNAL
SHUT-OFF.
10MIN. - 90MIN. At intervals of 10 minutes.
REMOTE2 MODE
You can customize the [REMOTE 2 IN] terminal
function.
Press ▲▼ to select [REMOTE2 MODE].1 )
Press ◄► to switch [REMOTE2 2 )
MODE].
The setting will change as follows each time
z
◄► is pressed.
DEFAULT USER L6500 SERIES
DEFAULT
The pin assignment of the [REMOTE
2 IN] terminal is used as the projector
default setting. (
Æ
page 121)
USER
This is used for changing the settings
for the REMOTE2 terminal.
Any settings you make for pins 2
to 8 become valid once you press
<ENTER> button.
L6500
SERIES
Use the setting for L6500-compatible
REMOTE 2 terminal.
FUNCTION BUTTON
You can assign a certain menu function to the
<FUNCTION> button as shortcut.
Press ▲▼ to select [FUNCTION 1 )
BUTTON].
Press <ENTER> button.2 )
The [FUNCTION BUTTON] screen will be
z
displayed.
Press ▲▼ to select a function.3 )
DISABLE Deactivate the <FUNCTION> button.
P IN P
Changes between OFF/USER1/
USER2/USER3 in P IN P.
(
Æ
page 88)
SUB
MEMORY
Displays the assigned SUB MEMORY
LIST. (
Æ
page 91)
SYSTEM
SELECTOR
Switches [SYSTEM SELECTOR]
options. (
Æ
page 58)
SYSTEM
DAYLIGHT
VIEW
Switches [SYSTEM DAYLIGHT
VIEW] options. (
Æ
page 56)
FREEZE Freezes the image.
WAVEFORM
MONITOR
Û
Displays the waveform of the input
signal.
PT-DZ110XE only:
Û
Press <ENTER> button.4 )
DATE AND TIME
This lets you set the time zone and the current date
and time for the projector’s internal clock.
Setting the TIME ZONE
J
Press ▲▼ to select [DATE AND TIME].1 )
Press <ENTER> button.2 )
Press ▲▼ to select [TIME ZONE].3 )
Press ◄► to switch [TIME ZONE].4 )
Adjusting the date and time
J
manually
Press ▲▼ to select [DATE AND TIME].1 )
Press <ENTER> button.2 )
Press ▲▼ to select [ADJUST CLOCK].3 )
PROJECTOR SETUP menu
86
- ENGLISH
Settings
Press <ENTER> button.4 )
The [ADJUST CLOCK] screen will be displayed.
z
Press ▲▼ to select the item to be set, 5 )
and press ◄► to set the local time.
Press ▲▼ to select [APPLY], and 6 )
press <ENTER> button.
This completes setting of the time.
z
Adjusting the date and time
J
automatically
Press ▲▼ to select [DATE AND TIME].1 )
Press <ENTER> button.2 )
Press ▲▼ to select [ADJUST CLOCK].3 )
Press <ENTER> button.4 )
The [ADJUST CLOCK] screen will be displayed.
z
Press ▲▼ to select [NTP 5 )
SYNCHRONIZATION] and press ◄► to
switch to [ON].
The setting will change as follows each time
z
◄► is pressed.
OFF ON
Press ▲▼ to select [APPLY], and 6 )
press <ENTER> button.
This completes setting of the time.
z
Note
To set the date and time automatically, the projector must
z
be connected to the network.
If synchronization with the NTP server fails just after
z
[NTP SYNCHRONIZATION] is turned [ON], or if [NTP
SYNCHRONIZATION] is turned [ON] while the NTP
server is not set, [NTP SYNCHRONIZATION] will return
to [OFF].
Access the projector via a web browser to set the NTP
z
server. (
Æ
page 107)
LENS CALIBRATION
This automatically sets the limit value of the lens shift
and the home position of the projector.
Press ▲▼ to select [LENS 1 )
CALIBRATION].
Press <ENTER> button.2 )
A conrmation message will be displayed.
z
Press ◄► to select [OK], and press 3 )
<ENTER> button.
To stop, select [CANCEL].
z
The lens will move vertically and horizontally,
z
and the limit value of the lens shift and home
position are set automatically.
The lens will stop, completing the calibration.
z
Note
While lens calibration is being executed, a message
z
[PROGRESS] appears on the menu. The calibration
cannot be canceled halfway.
If the lens calibration has been correctly executed, a
z
message [COMPLETE] will appear. If the calibration has
not been correctly executed, a message [INCOMPLETE]
will appear.
FILTER COUNTER RESET
After you replaced the Auto Cleaning Filter (ACF),
[REMAINING FILTER] of [STATUS] need to be reset
to [0].
Press ▲▼ to select [FILTER COUNTER 1 )
RESET].
Press <ENTER> button.2 )
The [RESET FILTER COUNTER?] screen will
z
be displayed.
Press ◄► to select [OK], and press 3 )
<ENTER> button.
Note
For replacing ACF unit, refer to
z
Procedure of ACF unit
replacement” (
Æ
page 110).
If the lter has not been installed, [OK] cannot be
z
selected.
The lter is wound during the resetting operation. Some
z
sound may be produced during the winding operation.
PROJECTOR SETUP menu
ENGLISH -
87
Settings
SAVE ALL USER DATA
This saves various setting values as a backup to the
internal memory of the projector.
Press ▲▼ to select [SAVE ALL USER 1 )
DATA].
Press <ENTER> button.2 )
The [SECURITY PASSWORD] screen will be
z
displayed.
Enter the password set for the 3 )
[SECURITY PASSWORD].
The conrmation screen will be displayed.
z
Press ◄► to select [OK], and press 4 )
<ENTER> button.
LOAD ALL USER DATA
This loads various setting values that were saved as a
backup to the internal memory of the projector.
Press ▲▼ to select [LOAD ALL USER 1 )
DATA].
Press <ENTER> button.2 )
The [SECURITY PASSWORD] screen will be
z
displayed.
Enter the password set for the 3 )
[SECURITY PASSWORD].
The conrmation screen will be displayed.
z
Press ◄► to select [OK], and press 4 )
<ENTER> button.
Note
If this is executed, the projector enters a standby state in
z
order to reect the setting values.
INITIALIZE
This returns various setting values to their factory
default settings.
Press ▲▼ to select [INITIALIZE].1 )
Press <ENTER> button.2 )
The [SECURITY PASSWORD] screen will be
z
displayed.
Enter the password set for the 3 )
[SECURITY PASSWORD].
The [INITIALIZE] screen will be displayed.
z
Press ▲▼ to select the desired 4 )
initialize item.
ALL USER
DATA
All setting values including [ENTRY
SIGNAL], [NETWORK/E-MAIL], and
[LOGO IMAGE] are returned to their
factory default values.
The projector enters a standby state
in order to reect the setting values.
ENTRY
SIGNAL
All setting values saved for each of
the input signals are cleared.
To clear just some registered
signals, perform the procedure
described in “Deleting a registered
data” (
Æ
page 90).
NETWORK/
E-MAIL
All setting values in [NETWORK
SETUP] and [E-mail setup] settings
will return to factory settings.
LOGO IMAGE
The registered image data for
[LOGO1] will return to factory
settings.
Press <ENTER> button.5 )
The conrmation screen will be displayed.
z
Press ◄► to select [OK], and press 6 )
<ENTER> button.
SERVICE PASSWORD
This function is used by a service person.
P IN P menu
88
- ENGLISH
Settings
P IN P menu
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
Using the P IN P function
Two videos can be projected simultaneously by
placing a separate small sub screen within the main
screen.
Press ▲▼ to select [P IN P].1 )
Press <ENTER> button.2 )
The [P IN P] screen will be displayed.
z
Press ▲▼ to select [P IN P MODE], 3 )
and press <ENTER> button.
The [P IN P MODE] screen will be displayed.
z
Press ▲▼ to select a function.4 )
OFF The P IN P function is not used.
USER1
The P IN P function is used with the
settings that were set in [Setting the
P IN P function].
USER2
USER3
Press <ENTER> button.5 )
Setting the P IN P function
The settings of the P IN P function can be saved to
[USER1], [USER2], and [USER3].
Select one of [USER1], [USER2], and 1 )
[USER3] modes in Step 4) of “Using
the P IN P function”, and press
<ENTER> button.
The setting screen for the selected mode is
z
displayed.
Press ▲▼ to select the desired setting 2 )
item, and press <ENTER> button.
The sub menu for the selected item appears.
z
MAIN
WINDOW
The input terminal for the main window is
displayed. (Press ▲▼ to select an item, and
press <ENTER> button to switch to the item.)
SIZE :
The user can specify the display size of the
main window between 10 % and 100 %.
POSITION :
The user can specify the display position of
the main window on the screen.
SUB
WINDOW
The input terminal for the subwindow is
displayed. (Press ▲▼ to select an item, and
press <ENTER> button to switch to the item.)
SIZE :
The user can specify the display size of the
sub window between 10 % and 100 %.
POSITION :
The user can specify the display position of
the subwindow on the screen.
CLOCK PHASE :
Set this if the pictures icker or their outlines
blur when the subwindow is RGB1 or RGB2.
(Set between 0 and 63)
FRAME
LOCK
The user can select the window to apply frame
lock. (Press ◄► to switch windows.)
[MAIN WINDOW] :
Frame lock is set for the input signals
specied for the main window.
[SUB WINDOW] :
Frame lock is set for the input signals
specied for the subwindow.
TYPE
The user can select the window that is
displayed by priority when two windows
overlap. (Press ◄► to switch windows.)
[MAIN WINDOW] :
The main window is displayed by priority.
[SUB WINDOW] :
The subwindow is displayed by priority.
Note
The P IN P function is not available depending on the
z
input signals and the selected input terminals. Refer to
“Two window display combination list” (
Æ
page 122) for
details.
The main window’s picture adjustment values such as the
z
picture mode, gamma selection and color temperature
setting for the main window will be applied.
In the normal screen (when the menu is not displayed),
z
the ◄► buttons can be used to switch the size and
position of the main window and subwindow when the P
IN P function is on.
TEST PATTERN menu
ENGLISH -
89
Settings
TEST PATTERN menu
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
TEST PATTERN
Results of adjustment of the position, size and other
factors are not reected in test patterns. Ensure the
input signal is displayed before performing various
kinds of setting.
Press ◄► to select the required test 1 )
pattern.
Cycle of displayed internal test
J
patterns
The setting will change as follows each time ◄►
is pressed.
MENU screen
+
Focus
MENU screen
+
Entry screen
MENU screen
+
Color bars
(HORIZONTAL)
MENU screen
+
All white
MENU screen
+
Color bars
(VERTICAL)
MENU screen
+
All black
MENU screen
+
Window (inversion)
MENU screen
+
Flag
MENU screen
+
Window
MENU screen
+
Flag (inversion)
SIGNAL LIST menu
90
- ENGLISH
Settings
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
REGISTERED SIGNAL STATUS
J
The name can be set for each sub memory.
z
MEMORY NO. : A1 (1-2)
z
Registering a signal to the list
When a new format input signal is applied to the
projector, press <MENU> button to register to the
SIGNAL LIST.
Note
You can register data up to 96 in total number of the
z
signal data and any corresponding sub memory data.
The memories are numbered over 12 pages (A to L: 8
z
data items can be registered on each page), and the
data is registered in the unused memory with the lowest
number. If all the memories are used, the data of the old
signals is overwritten in sequence.
The names of the registered data are automatically
z
determined by the input signals and memory numbers.
If a menu is being displayed, the new signals will be
z
registered at the instant they are input.
Renaming a registered data
Press ▲▼◄► to select the required 1 )
signal data.
Press <ENTER> button.2 )
The [REGISTERED SIGNAL STATUS] screen
z
will be displayed.
Displays the character list.
z
Press <MENU> button to return to the
z
[REGISTERED SIGNAL LIST] screen.
Press <ENTER> button.3 )
The [RENAME] screen will be displayed.
z
Press ▲▼◄► to select characters 4 )
and press <ENTER> button to input
them.
Press ▲▼◄► to select [OK], and 5 )
press <ENTER> button.
The [REGISTERED SIGNAL LIST] screen will
z
be displayed.
Press ▲▼◄► to select [CANCEL] and press
z
<ENTER> button to return to the [REGISTERED
SIGNAL LIST] without any change.
Deleting a registered data
Press ▲▼◄► to select the required 1 )
signal data.
Press <DEFAULT> button.2 )
The [ENTRY SIGNAL CLEAR] screen will be
z
displayed.
Press <MENU> button to cancel and return to
z
the [REGISTERED SIGNAL LIST] without any
change.
Press <ENTER> button.3 )
Displays [REGISTERED SIGNAL LIST] and
z
conrm the data is deleted.
Sub memory number
When the address number (A1, A2, …H7,
H8) signal is registered
SIGNAL LIST menu
SIGNAL LIST menu
ENGLISH -
91
Settings
Managing the sub memory
list
You can restore the sub memory data when using
signals from the same input source. Sub memory data
contains the setting information of screen and image
adjustments, such as BRIGHTNESS, CONTRAST or
ASPECT.
Registering the current settings
J
to the list
In the normal screen (when the menu 1 )
is not displayed), press ◄► button.
The signal must be registered before creating a
z
sub memory data of the signal.
Displays the list of corresponding sub memory
z
data to the signal.
Press ▲▼◄► to select the required 2 )
sub memory data.
Press <ENTER> button.3 )
The [ SIGNAL NAME] screen will be displayed.
z
Press <ENTER> button.4 )
Note
For renaming a registered data, follow the same
z
procedure (steps 4 - 5) of “Renaming a registered data”
(
Æ
page 90).
J
Displaying the sub memory list
and restoring the settings
In the normal screen (when the menu 1 )
is not displayed), press ◄► button.
The [SUB MEMORY LIST] screen will be
z
displayed.
Press ▲▼◄► to select the required 2 )
sub memory data, and press <ENTER>
button.
The [REGISTERED SIGNAL STATUS] screen
z
will be displayed.
Press <ENTER> button.3 )
Restores the settings in the data.
z
Deleting a sub memory data
J
In the normal screen (when the menu 1 )
is not displayed), press ◄► button.
The [SUB MEMORY LIST] screen will be
z
displayed.
Press ▲▼◄► to select the required 2 )
sub memory data, and press <ENTER>
button.
The [REGISTERED SIGNAL STATUS] screen
z
will be displayed.
Press <DEFAULT> button.3 )
Displays the [SUB MEMORY LIST] with
z
change.
You can return to the previous step by pressing
z
<MENU> button.
SECURITY menu
92
- ENGLISH
Settings
SECURITY menu
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
When you apply to the [SECURITY] menu
z
before you change the password to your original,
perform to input the following factory default
password operation.
Press ▲►▼◄▲►▼◄ and <ENTER> button.
Attention
When you apply to the SECURITY menu after you
z
change the password to your original in the [SECURITY
PASSWORD CHANGE] menu, input the original
password operation.
Note
Only asterisks * will appear on the screen to represent
z
the actual characters of the password when the password
is entered.
SECURITY PASSWORD
The [SECURITY PASSWORD] screen can be
displayed when the power has been turned on. If the
correct password is not entered, operations other
than using <STANDBY (
)> button and <SHUTTER>
button and adjusting the lens will not be possible.
Press ▲▼ to select [SECURITY 1 )
PASSWORD].
Press ◄► to switch [SECURITY 2 )
PASSWORD].
The setting will change as follows each time
z
◄► is pressed.
OFF ON
OFF Deactive
ON Active
Note
[PASSWORD] is set to [OFF] by default and when
z
initialized.
Change the SECURITY PASSWORD regularly and make
z
it uneasy to guess.
The security password becomes valid when setting of
z
the security password is turned [ON] and then the MAIN
POWER switch is turned off.
SECURITY PASSWORD
CHANGE
The password can be changed.
Press ▲▼ to select [SECURITY 1 )
PASSWORD CHANGE].
Press <ENTER> button.2 )
The [SECURITY PASSWORD CHANGE]
z
screen will be displayed.
Press ▲▼◄► and numeral keys to 3 )
set the password.
Up to 8 buttons can be set as the password.
z
Press <ENTER> button.4 )
For the purposes of conrmation, 5 )
enter the password again.
Press <ENTER> button.6 )
Note
Only asterisks * will appear on the screen to represent
z
the actual characters of the password when the password
is entered.
If the password input second does not match with the
z
password input rst, an error message is displayed. In
this case, input the correct password again.
When numerals are used in the SECURITY PASSWORD,
z
initialization of the security password will be necessary if
the remote control is lost. For the method of initialization,
consult your dealer.
SECURITY menu
ENGLISH -
93
Settings
DISPLAY SETTING
You can set your original text, such as company
name or URL information, to display regularly on the
projected image while projecting.
Press ▲▼ to select [DISPLAY 1 )
SETTING].
Press ◄► to switch [DISPLAY 2 )
SETTING].
The setting will change as follows each time
z
◄► is pressed.
OFF TEXT LOGO1
OFF The text display is disabled.
TEXT The text display is enabled.
LOGO1
The picture registered by the user
will be projected.
Note
Separate software [Logo Transfer Software] is required in
z
order to create the pictures to use for [LOGO1]. Consult
your dealer.
TEXT CHANGE
You can enter your original text to be displayed when
[DISPLAY SETTING] is turned [TEXT].
Press ▲▼ to select [TEXT CHANGE].1 )
Press <ENTER> button.2 )
The [TEXT CHANGE] screen will be displayed.
z
Press ▲▼◄► to select characters 3 )
and press <ENTER> button to input
them.
Press ▲▼◄► to select [OK], and 4 )
press <ENTER> button.
The text is now changed.
z
MENU LOCK
You can lock <MENU> button function and the
password will be asked to display the menu every
time.
Press ▲▼ to select [MENU LOCK].1 )
Press ◄► to switch [MENU LOCK].2 )
The setting will change as follows each time
z
◄► is pressed.
OFF ON
OFF
Deactivate the [MENU LOCK]
system.
ON Activate the [MENU LOCK] system.
Note
Once [MENU LOCK] is set to [ON], you cannot use
z
<MENU> button unless you input the correct password.
The [MENU LOCK] is set to [OFF] by default and when
z
initialized.
The unlock state is maintained until the projector is set to
z
the standby mode.
MENU LOCK PASSWORD
You can change the password for [MENU LOCK]
system to your original.
Press ▲▼ to select [MENU LOCK 1 )
PASSWORD].
Press <ENTER> button.2 )
The [MENU LOCK PASSWORD] screen will be
z
displayed.
Press ▲▼◄► to select characters 3 )
and press <ENTER> button to input
them.
Press ▲▼◄► to select [OK], and 4 )
press <ENTER> button.
To stop, select [CANCEL].
z
Attention
The factory default password is “AAAA”.
z
When the projector is initialized, the password will be
z
changed to the factory default setting, “AAAA”.
Change the MENU LOCK PASSWORD regularly and
z
make it uneasy to guess.
SECURITY menu
94
- ENGLISH
Settings
CONTROL DEVICE SETUP
Control from the remote control and main unit controls
can be restricted.
Press ▲▼ to select [CONTROL 1 )
DEVICE SETUP].
Press <ENTER> button.2 )
The [CONTROL DEVICE SETUP] screen will
z
be displayed.
Press ▲▼ to select [CONTROL 3 )
PANEL] or [REMOTE CONTROLLER].
Press <ENTER> button.4 )
[
z
CONTROL PANEL] screen or [REMOTE
CONTROLLER] screen will be displayed.
J
CONTROL PANEL
Restriction of control from the main unit controls
z
can be set.
ENABLE
Enables control from the main unit
controls.
DISABLE
Disables control from the main unit
controls.
J
REMOTE CONTROLLER
Restriction of control from the remote control
z
can be set.
ENABLE
Enables control from the remote
control.
DISABLE
Disables control from the remote
control.
Press ▲▼ to select [ENABLE] or 5 )
[DISABLE], and press <ENTER>
button.
The conrmation screen will be displayed.
z
Press ◄► to select [OK], and press 6 )
<ENTER> button.
Note
If an attempt is made to control the projector from the
z
remote control or main unit controls when [DISABLE] is
set, the [SECURITY PASSWORD] screen appears.
To change a setting, enter the security password and
change the operation setting.
The [SECURITY PASSWORD] screen disappears if
z
<MENU> button is pressed or no operation is performed
for 10 seconds.
If you [DISABLE] both of the [CONTROL PANEL] and
z
[REMOTE CONTROLLER] buttons, you cannot return to
the standby mode. Use this function with utmost care.
If a setting is reected, the on-screen menu disappears.
z
To continue operation, press <MENU> button to display
the main menu.
NETWORK menu
ENGLISH -
95
Settings
NETWORK menu
See “Navigating through the menu”
z
(
Æ
page 50).
See “MAIN MENU” and “SUB MENU”
z
(
Æ
page 51).
NETWORK SETUP
Make the initial network settings before using the
network connection.
Press ▲▼ to select [NETWORK 1 )
SETUP].
Press <ENTER> button.2 )
The [NETWORK SETUP] screen will be
z
displayed.
Press ▲▼ to select an item, and 3 )
change the setting according to the
instructions.
PROJECTOR
NAME
(Display of host
name and setting)
Change as needed when using
a DHCP server.
DHCP
(DHCP client
function)
Set [DHCP] item to [ON] when
to acquire an IP address
automatically using the DHCP
server.
Set to [OFF] if [DHCP] server is
not used. Enter the IP address if
DHCP server is not used.
IP ADDRESS
(Display of IP
address and
setting)
Enter the IP address if DHCP
server is not used.
SUBNET MASK
(Displaying
and setting the
subnet mask)
If not using a DHCP server, enter
the subnet mask.
DEFAULT
GATEWAY
(Display of gateway
address and
setting)
Enter the gateway address if
DHCP server is not used.
STORE
Save the current network
settings.
Press ▲▼ to select [STORE], and 4 )
press <ENTER> button.
Note
Before using the DHCP server, make sure the DHCP
z
server is already functioning.
For details of IP address, subnet mask, and gateway, ask
z
the network administrator.
NETWORK CONTROL
This sets the network control method.
Press ▲▼ to select [NETWORK 1 )
CONTROL].
Press <ENTER> button.2 )
The [NETWORK CONTROL] screen will be
z
displayed.
Press ▲▼ to select items, and press 3 )
◄► to change the setting.
WEB
CONTROL
Set this to [ON] when you want
to perform control with the Web
browser.
PJLink
CONTROL
Set this to [ON] when you want
to perform control with the PJLink
protocol.
COMMAND
CONTROL
Û
Set to [ON] to control using the
control command via the serial
terminal. (
Æ
page 120)
COMMAND
PORT
Set the port number used for the
command control.
STORE
Save the current network control
settings.
If settings have been made without an :
Û
administrator password of the Web browser
control, add 2-byte “00” instead of STX, and a line-
feed code (0Dh) instead of ETX. If settings have
been made with an administrator password of the
Web browser control, add a 32-byte hash value
and “00” instead of STX and a line-feed code (0Dh)
instead of ETX. The hash value is created by MD5
combining “admin1:”, password, “:” and random
numbers. The random numbers are 8-byte values
sent from the projector when connecting.
NETWORK STATUS
This displays the network status of the main unit.
Press ▲▼ to select [NETWORK 1 )
STATUS].
Press <ENTER> button.2 )
The [NETWORK STATUS] screen will be
z
displayed.
NETWORK menu
96
- ENGLISH
Settings
Network connections
The projector is equipped with network functions, and web browser controls can be used to carry out the following
operations from a computer.
Projector settings and adjustments
z
Projector status display
z
Transmission of E-mail messages if there is a problem with the projector
z
Note
A LAN cable is required to use the network function.
z
A Web browser is required to use this function. Make sure that a Web browser is available in the system.
z
Supported OS: Windows XP/Windows Vista/Windows 7, Mac OS X v10.4/v10.5/v10.6.
z
Supported browser: Internet Explorer 6.0/7.0/8.0, Safari 2.0/3.0/4.0 (Mac OS).
z
To use the E-mail function, communication with E-mail server must be established. Make sure that E-mail
z
feature is available in your system.
Use a straight insulated LAN cable which supports category 5 or above.
z
The length of LAN cable must be 100 m or shorter.
z
Name and function of network function parts
J
Attention
If the LAN terminal is touched by electrostatically charged hands (or body), failure may be caused by the discharge of static
z
electricity.
Be careful not to touch metallic part of LAN terminal or LAN cable.
Connect indoor equipment to the LAN.
z
LAN cable (straight)
Projector
LAN switch
LAN cable (straight)
Computer
LAN10/100 lamp (yellow)
This lights when a 100BASE-TX connection
is established.
LAN terminal (10BASE-T/100BASE-TX)
Connect LAN cable here.
LAN LINK/ACT lamp (green)
This lights when a LAN cable is connected
and ashes when signals are being received
or sent.
NETWORK menu
ENGLISH -
97
Settings
Accessing from the Web browser
Activate the Web browser in the personal computer.1 )
Enter the IP address set by the projector into the URL input eld of the Web browser.2 )
Enter your “User name” and “Password”.3 )
The factory default settings are user1 (user privileges) or admin1 (administrator privileges) for the user
z
name and panasonic (lowercase letters) for the password.
Click [OK] to display the Projector status page.4 )
Note
Avoid activating two or more Web browser simultaneously to work out setting or control actions.
z
Change the password rst of all.
z
Administrator privileges enable the use of all functions. User privileges enable the use of only “Projector status”, “Error
z
information”, “Network status”, “Basic control”, and “Change password”.
If the password is incorrectly entered three times in a row, the lock is set for several minutes.
z
NETWORK menu
98
- ENGLISH
Settings
Change Password page
J
Click [Change password].
Administrator
User
Administrator mode
Q
Administrator account
z
Account
Current user name input eld
Current password input eld
New user name input eld
New password input eld
New password input eld
(re-enter for conrmation)
Button for executing password change
User account
z
Account
New user name input eld
New password input eld
New password input eld
(re-enter for conrmation)
Button for executing password change
User mode
Q
A user can change password only.
Current password input eld
New password input eld
New password input eld
(re-enter for conrmation)
Button for executing password change
NETWORK menu
ENGLISH -
99
Settings
Basic control page
J
To move from another page, click [Projector control], then [Basic control].
Page selection tabs
Click these to switch pages.
This displays the on-screen status. It is displayed
even if the on-screen display of the projector is
set to off.
Monitor information button
Click this item, and the status of the projector is
displayed.
Detailed set up button
Click this item to display the advanced settings
page.
Change password button
Power On/Off control
SHUTTER control
OSD (On-screen Display) display/nondisplay
System type switching
Use these to select the input signals.
NETWORK menu
100
- ENGLISH
Settings
Detail control page
J
Click [Projector control], then [Detail control] to display the Detail control page.
Pressing these buttons controls the projector and
updates the on-screen description on the right of
the control page when control is nished.
Lens adjustment
Test pattern display
This button updates the on-screen description
on the right of the control page with the latest
information.
Menu display
Projector status page
J
Click [Status], then [Projector status] to display the Status information page.
This page displays the projector statuses established for the items shown below.
Displays the type of projector.
Displays the rmware version of the projector
main unit.
Displays the input switching status.
Displays temperature of projector’s intake air.
Displays temperature inside the projector.
Displays the AROUND LAMP TEMPERATURE.
Displays the lamp lit hours.
Displays the REMAINING FILTER QUANTITY.
Displays self-diagnosis information.
Displays used hours of the projector.
NETWORK menu
ENGLISH -
101
Settings
Error information page
J
When “Error (Detail)” is displayed on the status information screen, click it to display the error details.
Depending on the nature of the error, the projector may be placed in the standby mode for its own
z
protection.
When [FAILED] has appeared for an item
Q
Parameter Description
MAIN CPU BUS Trouble has occurred in the microcomputer circuitry. Consult your dealer.
FAN Trouble has occurred in the fan or its drive circuit. Consult your dealer.
INPUT AIR TEMPERATURE
The input air temperature is too high. It may be that the projector is being used in an
operating environment where the temperature is high such as near a heating appliance.
OPTICS MODULE TEMPERATURE
The temperature inside the projector is high. It may be that the projector is being used
in an operating environment where the temperature is high such as near a heating
appliance.
AROUND LAMP TEMPERATURE
The temperature around the lamp is too high. It may be that the projector’s ventilation
holes are blocked.
LAMP1 REMAIN TIME
The lamp runtime has exceeded the prescribed cumulative time, and it is now time to
replace the lamp.
LAMP2 REMAIN TIME
LAMP1 STATUS
The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
LAMP2 STATUS
APERTURE (CONTRAST-SHUTTER) Trouble has occurred in the contrast shutter circuitry. Consult your dealer.
INPUT AIR TEMP. SENSOR
Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer.
OPTICS MODULE TEMP. SENSOR
Trouble has occurred in the temperature detection sensor inside the projector.
Consult your dealer.
AROUND LAMP TEMP. SENSOR
Trouble has occurred in the sensor used to detect the exhaust air temperature.
Consult your dealer.
BATTERY The backup battery has been run out. Consult your dealer.
AIRFLOW SENSOR
Trouble has occurred in the sensor used to detect the airow volume.
Consult your dealer.
COVER OPEN The lamp unit cover is not attached securely. Check the lamp unit compartment.
ACF UNIT The air cleaning lter (ACF) is not installed or trouble has occurred. (
Æ
110 page)
FILTER REMAIN The lter remaining is getting less. (
Æ
109 page)
BRIGHTNESS SENSOR
Trouble has occurred in the brightness sensor. If the problem cannot be corrected by
turning the power off and on, consult your dealer.
AC POWER
AC power supply voltage input has dropped. Check that there is sufcient
electrical wiring capacity for the projector’s power consumption requirements.
Note
The ACCESS ERROR INFORMATLION/ACCESS INFORMATION displays the past several thousand accesses/requests.
z
If many accesses/requests are made at a time, some of them may not be found in the information.
Check the ACCESS ERROR INFORMATION/ACCESS INFORMATION regularly.
z
OK: Normal operation
FAILED: Occurrence of trouble
NETWORK menu
102
- ENGLISH
Settings
E-mail setup page
J
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can
be sent to one or more preset e-mail addresses (maximum two addresses).
Click [Detailed set up], then [E-mail set up] to display the E-mail setup page.
Select “Enable” to use the E-mail function.
Enter the IP address or server name of the E-mail
server (SMTP). The DNS server must be set if
the server name is entered.
Enter the E-mail address of the projector.
(maximum 63 characters)
The user can enter the location of, for example,
the installed projector so that the recipient
may easily identify the originator of the E-mail.
(maximum 63 characters)
The user can modify the minimum time interval
of temperature warning mail. The default value
is 60 minutes. In this case, the user cannot
send another mail for 60 minutes after sending
previous temperature warning mail even the set
warning temperature is reached again.
Enter the E-mail address of your desired
recipient.
Select the conditions for sending E-mail.
MAIL CONTENTS: Select [NORMAL] or [SIMPLE].
ERROR: an error is detected by self-diagnosis.
LAMP1 RUNTIME: remaining lamp service time has reached the value set in the eld.
LAMP2 RUNTIME: remaining lamp service time has reached the value set in the eld.
FILTER REMAIN: remaining lter service time has reached the value set in the eld.
INPUT AIR TEMPERATURE: intake air temperature has reached the value set in the eld.
NETWORK menu
ENGLISH -
103
Settings
Check these boxes when E-mail is to be sent periodically to the second E-mail address. E-mail will be sent
at the times and on the days checked.
NETWORK menu
104
- ENGLISH
Settings
E-mail setup page (continued)
J
Enter the E-mail address to which the E-mail is to be sent when two E-mail addresses are going to be
used. Do not enter it when the second E-mail address is not going to be used.
Select the conditions for sending E-mail to the second E-mail address.
MAIL CONTENTS: Select [NORMAL] or [SIMPLE].
ERROR: an error is detected by self-diagnosis.
LAMP1 RUNTIME: remaining lamp service time has reached the value set in the eld.
LAMP2 RUNTIME: remaining lamp service time has reached the value set in the eld.
FILTER REMAIN:
INPUT AIR TEMPERATURE: intake air temperature has reached the value set in the eld.
Check these boxes when E-mail is to be sent periodically to the second E-mail address. E-mail will be sent
at the times and on the days checked.
Button to update settings
NETWORK menu
ENGLISH -
105
Settings
Authentication set up page
J
The POP/SMTP server is set on this page when POP/SMTP authentication is required for mail transmissions.
Click [Detailed set up], then [Authentication set up] to display the Authentication server setup page.
Select the authentication method specied by
your Internet service provider.
Set this if SMTP authentication has been
selected.
POP server name eld
Available input characters:
Alphanumeric characters (A - Z, a - z, 0 - 9),
hyphen (-), period (.)
POP/SMTP server user name eld
POP/SMTP server password eld
Enter the port number for the SMTP server
(normally “25”).
Enter the port number for the POP server
(normally “110”).
Button to update settings
Ping test page
J
This page makes it possible to check whether the network is connected to the E-mail server, POP server,
DNS server, etc.
Click [Detailed set up], then [Ping test] to display the Ping test page.
Enter the IP address of the server to be tested.
Button for conducting the test.
Display which appears when the connection
failed.
Display which appears when the connection
was successful.
NETWORK menu
106
- ENGLISH
Settings
Contents of mail sent
J
Mail with the contents shown below is sent when the E-mail settings have been
Q
established.
ࣹࣹࣹࣜऌझपझयफपथटࣜबमफदडटरफमࣜमडबफमरࣤࣿऋऊंअःऑऎँࣹࣹࣹࣥࣜ
ऌमफदडटरफमࣜऐवबडࣶࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜऀखࣦࣦࣦࣦ
एडमथझनࣜऊफࣶࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜएओࣰࣱࣲ࣭࣮࣯ࣳ
ࣩࣩࣩࣩࣩࣜࣜँࣩऩझथनࣜयडरऱबࣜठझरझࣩࣩࣩࣩࣩࣜ
ऐँउऌँऎࣽऐऑऎँࣜओࣽऎऊअऊःࣜएँऐऑऌࣜ
उअऊअउऑउࣜऐअउँࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜझरࣜगࣲࣜ࣬ङࣜऩथपऱरडयࣜथपरडमलझनࣜ
अऊऌऑऐࣜࣽअऎࣜऐँउऌँऎࣽऐऑऎँࣜࣜऋलडमࣜगࣰࣱ࣭࣭࣯ࣜࣿࣜ࣫ࣜंࣜङࣜ
ँऎऎऋऎࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜऋंंࣜङࣜ
ईࣽउऌ࣭ࣜऎऑऊऐअउँࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜऋंंࣜङࣜࣜࣜझरࣜऎँउࣽअऊࣜगࣰࣜ࣬࣬ङࣜऄࣜ
ईࣽउऌ࣭ࣜऎऑऊऐअउँࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜऋंंࣜङࣜࣜࣜझरࣜऎँउࣽअऊࣜग࣮ࣜ࣬࣬ङࣜऄࣜ
ईࣽउऌ࣮ࣜऎऑऊऐअउँࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜऋंंࣜङࣜࣜࣜझरࣜऎँउࣽअऊࣜगࣰࣜ࣬࣬ङࣜऄࣜ
ईࣽउऌ࣮ࣜऎऑऊऐअउँࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜऋंंࣜङࣜࣜࣜझरࣜऎँउࣽअऊࣜग࣮ࣜ࣬࣬ङࣜऄࣜ
ंअईऐँऎࣜऎँउࣽअऊࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜऋंंࣜङࣜࣜࣜझरࣜऎँउࣽअऊࣜगࣰࣜ࣬࣬ङࣜऄࣜ
ंअईऐँऎࣜऎँउࣽअऊࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜऋंंࣜङࣜࣜࣜझरࣜऎँउࣽअऊࣜग࣮ࣜ࣬࣬ङࣜऄࣜ
अऊऌऑऐࣜࣽअऎࣜऐँउऌँऎࣽऐऑऎँࣜࣜࣜगࣜऋंंࣜङࣜ
ऌँऎअऋऀअࣿࣜऎँऌऋऎऐࣜ
एऱपठझवࣜࣜࣜࣜगࣜऋंंࣜङࣜࣜउफपठझवࣜࣜࣜࣜगࣜऋंंࣜङࣜࣜऐऱडयठझवࣜࣜࣜगࣜऋंंࣜङࣜࣜओडठपडयठझवࣜगࣜऋंंࣜङࣜ
ऐतऱमयठझवࣜࣜगࣜऋंंࣜङࣜࣜंमथठझवࣜࣜࣜࣜगࣜऋंंࣜङࣜࣜएझरऱमठझवࣜࣜगࣜऋंंࣜङࣜ
ࣶ࣬࣬࣬࣬ࣜࣜगࣜऋंंࣜङ࣭ࣶࣜࣜࣜࣜ࣬࣬࣬ࣜࣜगࣜऋंंࣜङ࣮ࣶࣜࣜࣜࣜ࣬࣬࣬ࣜࣜगࣜऋंंࣜङ࣯ࣶࣜࣜࣜࣜ࣬࣬࣬ࣜࣜगࣜऋंंࣜङࣜ
ࣰࣶ࣬࣬࣬ࣜࣜगࣜऋंंࣜङࣱࣶࣜࣜࣜࣜ࣬࣬࣬ࣜࣜगࣜऋंंࣜङࣲࣶࣜࣜࣜࣜ࣬࣬࣬ࣜࣜगࣜऋंंࣜङࣶࣜࣜࣜࣜ࣬ࣳ࣬࣬ࣜࣜगࣜऋंंࣜङࣜ
ࣶ࣬ࣴ࣬࣬ࣜࣜगࣜऋंंࣜङࣶࣜࣜࣜࣜ࣬ࣵ࣬࣬ࣜࣜगࣜऋंंࣜङ࣭ࣶࣜࣜࣜࣜ࣬࣬࣬ࣜࣜगࣜऋंंࣜङ࣭࣭ࣶࣜࣜࣜࣜ࣬࣬ࣜࣜगࣜऋंंࣜङࣜ
࣭࣮ࣶ࣬࣬ࣜࣜगࣜऋंंࣜङ࣭࣯ࣶࣜࣜࣜࣜ࣬࣬ࣜࣜगࣜऋंंࣜङࣰ࣭ࣶࣜࣜࣜࣜ࣬࣬ࣜࣜगࣜऋंंࣜङࣱ࣭ࣶࣜࣜࣜࣜ࣬࣬ࣜࣜगࣜऋंंࣜङࣜ
ࣲ࣭ࣶ࣬࣬ࣜࣜगࣜऋंंࣜङ࣭ࣶࣜࣜࣜࣜࣳ࣬࣬ࣜࣜगࣜऋंंࣜङ࣭ࣶࣜࣜࣜࣜࣴ࣬࣬ࣜࣜगࣜऋंंࣜङ࣭ࣶࣜࣜࣜࣜࣵ࣬࣬ࣜࣜगࣜऋंंࣜङࣜ
࣮ࣶ࣬࣬࣬ࣜࣜगࣜऋंंࣜङ࣮࣭ࣶࣜࣜࣜࣜ࣬࣬ࣜࣜगࣜऋंंࣜङ࣮࣮ࣶࣜࣜࣜࣜ࣬࣬ࣜࣜगࣜऋंंࣜङ࣮࣯ࣶࣜࣜࣜࣜ࣬࣬ࣜࣜगࣜऋंंࣜङࣜ
ࣩࣩࣩࣩࣩࣜࣜटतडटधࣜयवयरडऩࣩࣩࣩࣩࣩࣜ
उࣽअऊࣜࣿऌऑࣜࣾऑएࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ंࣽऊࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
अऊऌऑऐࣜࣽअऎࣜऐँउऌँऎࣽऐऑऎँࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ऋऌऐअࣿएࣜउऋऀऑईँࣜऐँउऌँऎࣽऐऑऎँࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣽऎऋऑऊऀࣜईࣽउऌࣜऐँउऌँऎࣽऐऑऎँࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
Mail with the contents shown below is sent when an error has occurred.
Q
ࣹࣹࣹࣜऌझपझयफपथटࣜबमफदडटरफमࣜमडबफमरࣤँऎऎऋऎࣹࣹࣹࣥࣜ
ऌमफदडटरफमࣜऐवबडࣶࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜऀखࣦࣦࣦࣦ
एडमथझनࣜऊफࣶࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜएओࣰࣱࣲ࣭࣮࣯ࣳ
ࣩࣩࣩࣩࣩࣜࣜटतडटधࣜयवयरडऩࣩࣩࣩࣩࣩࣜ
उࣽअऊࣜࣿऌऑࣜࣾऑएࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ंࣽऊࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
अऊऌऑऐࣜࣽअऎࣜऐँउऌँऎࣽऐऑऎँࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ऋऌऐअࣿएࣜउऋऀऑईँࣜऐँउऌँऎࣽऐऑऎँࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣽऎऋऑऊऀࣜईࣽउऌࣜऐँउऌँऎࣽऐऑऎँࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ईࣽउऌ࣭ࣜऎँउࣽअऊࣜऐअउँࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ईࣽउऌ࣮ࣜऎँउࣽअऊࣜऐअउँࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜंࣽअईँऀࣜङ
ईࣽउऌ࣭ࣜएऐࣽऐऑएࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ईࣽउऌ࣮ࣜएऐࣽऐऑएࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣽऌँऎऐऑऎँࣤࣿऋऊऐऎࣽएऐࣩएऄऑऐऐँऎࣥࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
अऊऌऑऐࣜࣽअऎࣜऐँउऌ࣪एँऊएऋऎࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ऋऌऐअࣿएࣜउऋऀऑईँࣜऐँउऌ࣪एँऊएऋऎࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣽऎऋऑऊऀࣜईࣽउऌࣜऐँउऌ࣪एँऊएऋऎࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣾࣽऐऐँऎकࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣽअऎंईऋओࣜएँऊएऋऎࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣿऋऒँऎࣜऋऌँऊࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣾऎअःऄऐऊँएएࣜएँऊएऋऎࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣽࣿंࣜऑऊअऐࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ंअईऐँऎࣜऎँउࣽअऊࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣽࣿࣜऌऋओँऎࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜगࣜࣜࣜऋइࣜࣜࣜङ
ࣤँममफमࣜटफठड࣭ࣜ࣬ࣜ࣬࣬ࣜ࣬࣬ࣜ࣬࣬ࣜ࣬࣬ࣜ࣬࣬ࣜ࣬࣬ࣜ࣬࣬ࣥ
अपबऱरࣜझथमࣜरडऩबडमझरऱमडࣶ࣭ࣜࣜࣜࣜࣜࣜࣜࣴࣜठडणࣰࣲࣿࣜ࣫ࣜࣜࣜठडणं
ऋबरथटयࣜऩफठऱनडࣜरडऩबडमझरऱमडࣶ࣮ࣜࣜࣜ࣬ࣜठडणࣲࣿࣜ࣫ࣜࣜࣴࣜठडणं
ࣽमफऱपठࣜनझऩबࣜरडऩबडमझरऱमडࣱࣶ࣮ࣜࣜࣜࣜࣜࣜठडणࣿࣜ࣫ࣜࣜࣳࣳࣜठडणं
एँऐࣜऎऑऊऐअउँ࣮ࣜࣜࣜࣜࣜࣜ࣬࣬࣬ࣜऄ
ऌऋओँऎࣜऋऊ࣭ࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜ࣬࣬ࣜरथऩडय
ईࣽउऌ࣭ࣜऋऊ࣭ࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜ࣬࣬ࣜरथऩडय
ईࣽउऌ࣭ࣜईऋओࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜ࣬ࣜऄ
ईࣽउऌ࣭ࣜऄअःऄ࣮ࣜࣜࣜࣜࣜࣜࣜ࣬࣬࣬ࣜऄ
ईࣽउऌ࣭ࣜऎँउࣽअऊࣜࣜࣜࣜࣜࣜࣜࣜ࣬ࣜऄ
ईࣽउऌ࣮ࣜऋऊࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜ࣬ࣜरथऩडय
ईࣽउऌ࣮ࣜईऋओࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜ࣬ࣜऄ
ईࣽउऌ࣮ࣜऄअःऄࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜ࣬ࣜऄ
ईࣽउऌ࣮ࣜऎँउࣽअऊ࣮ࣜࣜࣜࣜࣜ࣬࣬࣬ࣜऄ
ࣩࣩࣩࣩࣩࣩࣩࣜऎडऩझथपथपणࣜढथनरडमࣩࣩࣩࣩࣩࣩࣩࣩࣜ
ऍऑࣽऊऐअऐक࣭ࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜ࣬࣬ࣜ࣡
ࣽऌऌऋऎऋऔ࣪ࣜऐअउँ࣭ࣜࣜࣜ࣬࣬࣬࣬ࣜऄ
ࣩࣩࣩࣩࣩࣩࣩࣩࣜࣿऱममडपरࣜयरझरऱयࣩࣩࣩࣩࣩࣩࣩࣩࣩࣜ
उࣽअऊࣜऒँऎएअऋऊ࣭ࣜࣜࣜࣜࣜࣜࣜࣜࣜ࣪࣬࣬ࣜ
ऊँऐओऋऎइࣜऒँऎएअऋऊ࣭ࣜࣜࣜࣜࣜࣜ࣪࣬࣬
NETWORK menu
ENGLISH -
107
Settings
J
Adjust clock page
Click [Detailed set up], then [Adjust clock] to display the Adjust clock page.
Time zone selection
Button to update time zone setting
Turn this [ON] to set the date and time
automatically.
When setting the date and time automatically,
input the IP address or name of the NTP server.
(When inputting the server name, the DNS server
must be set.)
New date eld
New time eld
Button to update time and date settings
Note
If the time becomes incorrect immediately after setting the correct time, then the battery needs to be changed.
z
Contact the dealer where you bought the projector to have the battery changed.
J
Network cong page
Click [Detailed set up], then [Network cong] to display the Network cong page.
If [Network cong] is clicked, the "CAUTION!" screen is displayed.
z
If the [Next] button is clicked, the current settings are displayed.
z
If the [Change] button is clicked, the following setting change screen is displayed.
z
Enter the name of the projector here. Enter the
host name here if it is required when the DHCP
server is going to be used, for instance.
Set this to ON to enable the DHCP client function.
Enter the IP address if DHCP server is not used.
Enter the SUBNET MASK if DHCP server is not
used.
Enter the gateway address if DHCP server is not
used.
DNS server address (primary) eld
Available input characters:
Numeric characters (0 - 9), period (.)
(Example: 192.168.0.253)
DNS server address (secondary) eld
Available input characters:
Numeric characters (0 - 9), period (.)
(Example: 192.168.0.254)
When all options are lled, click [NEXT]. The
conrmation screen will be displayed.
Click [Submit] button to update.
Monitor Lamp indicators
108
- ENGLISH
Maintenance
Monitor Lamp indicators
Managing the indicated problems
If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as
follow.
Attention
J
LAMP1/LAMP2 indicator
Lamp
indication
Information Check point Remedial measure
Lighting in red
Indicates the time
for replacing the
lamp unit.
Did you notice a “REPLACE
z
LAMP” message on the screen
when turning on the projector
power supply?
This lamp monitor lights up when the
z
lamp unit used hours have reached
2 800 hours (when [HIGH] is selected
as the [LAMP POWER] setting).
Request the dealer to replace the lamp
z
unit.
Blinking in red
(once)
Lamp unit is not
installed.
Check the lamp unit
z
compartment.
Install the lamp unit.
z
When lamp unit is installed and still
z
having the indicator lights, contact to
the dealer.
Blinking in red
(3 times)
Error is detected
in the lamp circuit.
Did you turn the power back
z
on immediately after turning it
off?
Wait until the lamp has cooled off, and
z
then turn on the power.
Some error has arisen in the
z
lamp circuit.
Check for uctuation (or drop)
z
in the source voltage.
Turn off the MAIN POWER switch
z
using the procedure on page 40 and
consult the dealer.
Note
If no problem is found or the problem remains, do not turn on the projector. Instead contact your dealer.
z
Filter indicator (FILTER)
Temperature indicator (TEMP)
Lamp2 indicator (LAMP2)
Lamp1 indicator (LAMP1)
Power indicator
(STANDBY (R) / ON (G))
Monitor Lamp indicators
ENGLISH -
109
Maintenance
J
TEMP indicator
Lamp
indication
Information Check point Remedial measure
Lighting in red
Warm-up status
Did you turn on the power when
z
the ambient temperature was
lower than approx. 0 °C (32 °F)?
Wait about 5 minutes in the current
z
status.
Install the unit in a location having
z
an ambient temperature from 0 °C
(32 °F) - 45 °C (113 °F).
High temperature
inside. (WARNING)
Check the ventilation port is
z
blocked.
Is the room air temperature too
z
high?
Is the lter indicator lighted?
z
Remove the object that is blocking
z
the ventilation port.
Move the projector to a temperature
z
of 0 °C (32 °F) - 45 °C (113 °F) and
the humidity of 20 % to 80 % (no
condensation).
Turn off the MAIN POWER switch
z
using the procedure on page 40 and
replace the ACF unit.
Blinking in red
(once)
The lter is
excessively dirty
and the ventilation
is poor.
Blinking in red
(twice)
High temperature
inside.
(Standby condition)
Blinking in red
(3 times)
Cooling fan has
been stopped.
Turn off the MAIN POWER switch
z
using the procedure on page 40 and
consult the dealer.
Note
If no problem is found or the problem remains, do not turn on the projector. Instead contact your dealer.
z
J
FILTER indicator
Lamp
indication
Information Check point Remedial measure
Lighting in red
The ACF unit has
run out.
Check the [REMAINING
z
FILTER] of [STATUS] in
[PROJECTOR SETUP] menu.
(
Æ
page 84)
Replace the ACF unit.
z
Blinking in red
The ACF unit is not
installed.
Check the ACF unit
z
compartment.
Replace the ACF unit.
z
Lighting in
orange
The ACF unit
remains few. The
remaining use time
of the ACF unit is
approximately 200
hours.
Check the [REMAINING
z
FILTER] of [STATUS] in
[PROJECTOR SETUP] menu.
(
Æ
page 84)
Request the dealer to purchase the
z
new ACF unit.
Blinking in
orange
The ACF unit cannot
operate properly.
Is foreign object blocking the
z
ACF unit operation?
Remove the foreign object from the
z
ACF unit.
When the foreign object still
z
remained, contact the dealer.
Note
If no problem is found or the problem remains, do not turn on the projector. Instead contact your dealer.
z
When the ACF unit is not installed, the lter indicator will blink in red and the power will turn off in 10 minutes.
z
When the FILTER indicator is ashing green, the Auto Cleaning Filter (ACF) is normally rolling up.
z
When the ACF unit is operating, operational sound may be heard.
z
The usable time after lighting of the orange lamp may be shortened in a dusty environment. The time of about 200 hours is
z
for reference only. Contact the dealer to purchase the new ACF unit earlier.
If the projector is used at elevations higher than 1 400 m above sea level with the [HIGH ALTITUDE MODE] at [OFF], the
z
lamp life or life of other components will be shortened.
Before the FILTER indicator blinks in orange when operational malfunction, mechanical sound of the clutch may be heard.
z
If the Smoke Cut Filter is installed, the green lamp, which takes longer to turn ON/OFF, will ash.
z
If the lter is running low, only one lamp lights even if [DUAL] is selected. The lamps will light as normal once the lter has
z
been replaced and the residual lter has been reset.
Replacement
110
- ENGLISH
Maintenance
Replacement
Before replacing the unit
Turn off the POWER switch of the projector in proper way and disconnect the power plug from the wall outlet.
z
(
Æ
pages 39, 41)
Be sure to observe the procedure “Powering off the projector”
z
(
Æ
page 41) when performing power supply
operation.
Replacing the unit
J
ACF (Auto Cleaning Filter) unit
ACF unit is an optional accessory.
You can check the remaining amount of the ACF unit in [REMAINING FILTER] of [STATUS] in PROJECTOR
SETUP menu. (
Æ
page 84)
Contact an Authorized Service Center to purchase a Replacement lter unit (ET-ACF310).
z
J
Procedure of ACF unit replacement
Loosen “ACF cover xing screw” (1 1 )
screw) until the screws turn freely and
remove the “ACF cover”.
Slide out the “ACF unit” from the 2 )
projector slowly.
When you replace the “ACF unit”, clean the
z
compartment and/or the air exhaust port if you
need to.
Insert the new “ACF unit” into the 3 )
compartment in correct direction and
slightly push until it clicks.
Attach the “ACF cover” and tighten 4 )
“ACF cover xing screw” (1 screw)
securely.
Select [FILTER COUNTER RESET] 5 )
in [PROJECTOR SETUP] menu, and
press <ENTER> button. (
Æ
page 86)
Press ◄► to select [OK], and press 6 )
<ENTER> button.
Note
When the ACF unit is not installed, the lter indicator will
z
blink in red and the power will turn off in 10 minutes. (The
time before the power is turned off is indicated by the unit
of 1 minute.)
The replacement timing of the ACF depends on
z
environment of usage.
When resetting is performed, the lter will be wound.
z
The part numbers of accessories and separately sold
z
components are subject to change without notice.
Always install the ACF unit when using the projector.
z
Attention
When installing the ACF unit, take care not to touch the
z
lter surface.
Be sure to install the ACF unit when using the projector.
z
The ACF unit to be replaced should be an unused
z
product.
ACF cover
ACF cover xing screw
ACF unit
CANCELOK
EXECUTE
CHANGE
[ENTER]
RESET FILTER COUNTER?
Replacement
ENGLISH -
111
Maintenance
J
Lamp unit
The LAMP unit is consumable product. You can check the duration of usage time using [LAMP1/LAMP2] of
[STATUS] (
Æ
page 84) in the [PROJECTOR SETUP] menu.
Replacement of the lamp unit should be carried out by a qualied technician.
Contact the dealer to purchase a replacement lamp unit (ET-LAD310:1 bulb unit, ET-LAD310W: 2 bulb units).
Precautions on lamp unit replacement
J
Handle the lamp unit with special care as the lamp is made of glass. Dropping or giving it a shock may
z
cause it to burst or damaged.
Phillips screwdriver is necessary when replacing a lamp unit.
z
When replacing the lamp unit, be sure to hold it by the handle.
z
The lamp may burst. Replace the lamp unit carefully so that the broken pieces of the lamp glass will not
z
scatter. When the projector is mounted on the ceiling, do not work directly under the projector or put your
face closer to the projector.
For disposition of used lamps, request an industrial waste disposal contractor.
z
Attention
Do not attempt replacement with an unauthorized lamp unit.
z
The part numbers of accessories and separately sold components are subject to change without notice.
z
Wait for more than 1 hour and make sure the lamp unit and the surroundings are cooled enough.
z
Prior to replacing the lamp unit, allow it to cool down to prevent the risk of burns, damage and other hazards.
z
J
When to replace the lamp unit
When the lamp is consumed, the brightness may decrease over time. 3 000 hours of use is the replacing
time as a rough guide, and that might be shortened by the usage conditions, characteristics of the lamp
unit or environmental conditions. Therefore, it is strongly recommended for the user to keep a spare lamp.
If the lamp unit has not been replaced after 3 000 hours of operation have elapsed, the power will turn off
automatically approximately 10 minutes after it is turned on.
On screen LAMP indicator
Over 2 800 hours
[REPLACE LAMP] is displayed on the upper left
of the screen for 30 seconds. Press any button to
clear the screen, or disappears after 30 seconds.
Lights in red.
Over 3 000 hours
[REPLACE LAMP] is displayed on the upper left
of the screen, and it will stay until you respond. To
clear the screen, press any button.
Note
The guide times,
z
3 000 hours, are rough estimates based on certain conditions and are not a guaranteed time.
REPLACE LAMP
Replacement
112
- ENGLISH
Maintenance
J
Procedure of lamp unit replacement
Attention
When the projector is mounted in the ceiling, do not work directly under the projector or put your face close to the projector.
z
The lamp unit and the lamp unit cover must be attached correctly and securely.
z
If the lamp unit is not installed smoothly, remove it and then install it again. If it is pushed in forcibly, its connector may be
z
broken.
Turn the main power OFF, following the 1 )
procedures described in “Powering off
the projector” (
Æ
page 41), disconnect
the power plug from the AC power
source, and wait for one hour or more.
Then check that the lamp unit has
cooled down.
Turn the “lamp unit cover xing 2 )
screw” (1 piece) with a Phillips-head
screwdriver until it is fully loosened,
and then hold the “lamp unit cover”
securely and open it in the direction of
the arrow.
Use a Phillips screwdriver to loosen 3 )
the “Lamp unit cover xing screw” (4
screws) for the lamp unit to be replaced
until the screws turn freely. Hold the
“Handle” of the “Lamp unit” and
gently pull the lamp unit out from the
projector.
Replace the new LAMP unit in correct 4 )
direction.
Use a Phillips screwdriver to securely 5 )
tighten the 2 “Lamp unit cover xing
screw” for each lamp unit.
Close the “lamp unit cover” and 6 )
tighten the “lamp unit cover xing
screw” (1 piece) securely with a
Phillips-head screwdriver in the
reverse order to Step 2).
Note
When the lamp unit is replaced, the duration of usage
z
time will be reset to “0”.
Lamp unit cover
xing screw
Lamp unit cover
Lamp unit xing screws
Lamp unit 1HandleLamp unit 2
Lamp unit
installation guide
Groove for lamp unit installation guide
Groove for lamp unit installation guide
Troubleshooting
ENGLISH -
113
Maintenance
Troubleshooting
Should any problem persist, contact your dealer.
Problem Cause
Reference
page
Power does not turn
on.
The power cord may not be connected.
z
The <MAIN POWER> switch is turned off.
z
41
No electric supply is at the wall outlet.
z
The circuit breakers have tripped.
z
[LAMP1/LAMP2 indicator] or [TEMP indicator]is lit or ashes.
z
108, 109
The lamp unit cover has not been securely installed.
z
112
No picture appears.
The video signal input source may not be connected to a terminal
z
properly.
35
The input selection setting may not be correct.
z
47
The [BRIGHTNESS] adjustment setting may be at the minimum setting.
z
54
The input source which is connected to the projector may have a
z
problem.
The [SHUTTER] function may be in use.
z
47
If the [Power indicator] ashes in red, consult your dealer.
z
The picture is fuzzy.
The lens focus may not have been set correctly.
z
42
The projector may not be at the correct distance from the screen.
z
23
The lens may be dirty.
z
16
The projector may be tilted too much.
z
The color is pale or
grayish.
[COLOR] or [TINT] adjustment may be incorrect.
z
54
The input source which is connected to the projector may not be
z
adjusted correctly.
RGB cable is damaged.
z
The remote control
does not operate.
The batteries may be weak.
z
The batteries may not have been inserted correctly.
z
18
The remote control signal receptor on the projector may be obstructed.
z
18
The remote control unit may be out of the operation range.
z
18
Strong light such as uorescent shine onto the signal receptor.
z
18
[REMOTE CONTROLLER] of [CONTROL DEVICE SETUP] in
z
SECURITY menu is [DISABLE].
94
Is the remote 2 (REMOTE2 IN) terminal used for external control?
z
121
The remote control ID setting is incorrect.
z
21, 76
On screen menu
does not appear.
ON SCREEN button on the remote control may have been pressed and
z
cleared.
47
The control buttons
of the projector do
not operate.
[CONTROL PANEL] of [CONTROL DEVICE SETUP] in SECURITY
z
menu is [DISABLE].
94
Is the remote 2 (REMOTE2 IN) terminal used for external control?
z
121
The picture does not
display correctly.
[SYSTEM SELECTOR] may not have been set correctly.
z
58
There may be a problem with the VCR or other signal source.
z
A signal which is not compatible with the projector is being input.
z
123
Troubleshooting
114
- ENGLISH
Maintenance
Problem Cause
Reference
page
Picture from a
computer does not
appear.
The cable may be longer than the optional cable.
z
The external video output from a laptop computer may not be correct.
z
(You may be able to change the external output settings by pressing the
[Fn] + [F3] or [Fn] + [F10] keys simultaneously. The actual method varies
depending on the type of computer; refer to the documentation provided
with your computer for further details.)
Picture from a
computer DVI-D
graphic board does
not appear.
[DVI-D IN] setting in [DISPLAY OPTION] menu may be incorrect setting.
z
73
The graphic board driver of the computer needs to be updated to the
z
latest version.
The computer may need to be restarted after switching [DVI-D IN]
z
setting in [DISPLAY OPTION] menu of the projector correctly.
73
Projection suddenly
became darker.
Has the lter been used up? (When the lter has been used up, the
z
projector is not shut down but is automatically switched to a [LOW] lamp
output mode using one lamp.)
109
Technical Information
ENGLISH -
115
Appendix
Technical Information
PJLink protocol
The network function of the projector supports PJLink class 1, and the PJLink protocol can be used to perform
projector setting and projector status query operations from a computer.
Control commands
J
The following table lists the PJLink protocol commands that can be used to control the projector.
Command Control details Notes
POWR Power supply control
Parameters
0 = Standby
1 = Power ON
POWR ? Power supply status query
Parameters
0 = Standby 1 = Power ON
2 = Cool-down in progress 3 = Warm-up in progress
INPT Input selection Parameters
11 = RGB1 12 = RGB2 21 = VIDEO
22 = S-VIDEO 31 = DVI-D 32 = HDMI
33 = SDI (PT-DZ110XE/PT-DS100XE only)
INPT ? Input selection query
AVMT Shutter control Parameters
30 = Shutter mode off (picture mute canceled)
31 = Shutter mode on (picture mute)
AVMT ? Shutter mode query
ERST ? Error status query
Parameters
1st byte : Indicates fan errors, range 0 - 2
2nd byte : Indicates lamp errors, range 0 - 2
3rd byte : Indicates temperature errors, range 0 - 2
4th byte : Indicates cover open errors, range 0 - 2
5th byte : Indicates lter errors, range 0 - 2
6th byte : Indicates other errors, range 0 - 2
Denitions for each value from 0 to 2 are as follows.
0 = No error known 1 = Warning 2 = Error
LAMP ? Lamp status query
Parameters
1st digits (1 - 5 digits) : Lamp 1 cumulative operating time
2nd digit : 0 = Lamp 1 off, 1 = Lamp 1 on
3rd digits (1 - 5 digits) : Lamp 2 cumulative operating time
4th digit : 0 = Lamp 2 off, 1 = Lamp 2 on
INST ? Input selection list query
The following are returned as parameters.
“11 12 21 22 31 32” (PT-DW90XE only)
“11 12 21 22 31 32 33” (PT-DZ110XE/PT-DS100XE only)
NAME ? Projector name query
The name set for [PROJECTOR NAME] in [NETWORK SETUP] is
returned.
INF1 ? Manufacturer name query “Panasonic” is returned.
INF2 ? Model name query “DZ110XE”, “DS100XE” or “DW90XE” is returned.
INF0 ? Other information query Information such as version number is returned.
CLSS ? Class information query “1” is returned.
PJLink security authorization
J
When using PJLink with security authorization, either of the password set for administrator privileges and the
password set for user privileges with Web browser control can be used as the password for PJLink.
When using PJLink without security authorization, set use without the password for administrator privileges
and the password for user privileges of Web browser control.
For specications regarding PJLink, refer to the Japan Business Machine and Information System
z
Industries Association website.
URL http://pjlink.jbmia.or.jp/
Technical Information
116
- ENGLISH
Appendix
Control commands via LAN
When WEB Control administrator rights password is set (Protect mode)
J
<Connection method>
Obtain the IP address and port number (Initial set value = 1024) of the projector and 1 )
make a request for connection to the projector.
You can obtain both IP address and port number from the menu screen of the projector.
IP address : Obtain from MAIN MENU
[NETWORK]
[NETWORK STATUS]
Port No. : Obtain from MAIN MENU
[NETWORK]
[NETWORK CONTROL]
[COMMAND PORT]
There is a response from the projector.2 )
Response data
Data section Blank Mode Blank
Random number
section
Termination
symbol
“NTCONTROL”
(ASCII string)
‘ ’
0x20
‘1’
0x31
‘ ’
0x20
“zzzzzzzz”
(ASCII code hexadecimal
number)
(CR)
0x0d
9 bytes 1 byte 1 byte 1 byte 8 bytes 1 byte
Mode : 1 = Protect mode
Generate a 32-byte hash value from the following data using MD5 algorithm.3 )
“xxxxxx:yyyyy:zzzzzzzz”
xxxxxx : Administrator rights user name for WEB CONTROL
(Default user name is “admin1”)
yyyyy : Password of above administrator rights user
(Default password is “panasonic”)
zzzzzzzz : 8-byte random number obtained in Step 2)
<Command transmission method>
Transmit using the following command format.
Transmitted data
Header Data section
Termination
symbol
Hash value
(See above
<Connection method>)
‘0’
0x30
‘0’
0x30
Control command
(ASCII string)
(CR)
0x0d
32 bytes 1 byte 1 byte Undened length 1 byte
Receive data
Header Data section
Termination
symbol
‘0’
0x30
‘0’
0x30
Control command
(ASCII string)
(CR)
0x0d
1 byte 1 byte Undened length 1 byte
Error response
Error message Termination symbol
“ERR1”
“ERR2”
“ERR3”
“ERR4”
“ERR5”
“ERRA”
Undened control command
Out of parameter range
Busy state or no-acceptable period
Timeout or no-acceptable period
Wrong data length
Password mismatch
(CR)
0x0d
4 bytes 1 byte
Technical Information
ENGLISH -
117
Appendix
When WEB Control administrator rights password is not set
J
(Non-protect mode)
<Connection method>
Obtain the IP address and port number (Initial set value = 1024) of the projector and 1 )
make a request for connection to the projector.
You can obtain both IP address and port number from the menu screen of the projector.
IP address : Obtain from MAIN MENU
[NETWORK]
[NETWORK STATUS]
Port number : Obtain from MAIN MENU
[NETWORK]
[NETWORK CONTROL]
[COMMAND PORT]
There is a response from the projector.2 )
Response data
Data section Blank Mode
Termination
symbol
“NTCONTROL”
(ASCII string)
‘ ’
0x20
‘0’
0x30
(CR)
0x0d
9 bytes 1 byte 1 byte 1 byte
Mode : 0 = Non-protect mode
<Command transmission method>
Transmit by the following command format.
Transmitted data
Header Data section
Termination
symbol
‘0’
0x30
‘0’
0x30
Control command
(ASCII string)
(CR)
0x0d
1 byte 1 byte Undened length 1 byte
Receive data
Header Data section
Termination
symbol
‘0’
0x30
‘0’
0x30
Control command
(ASCII string)
(CR)
0x0d
1 byte 1 byte Undened length 1 byte
Error response
Error message Termination symbol
“ERR1”
“ERR2”
“ERR3”
“ERR4”
“ERR5”
“ERRA”
Undened control command
Out of parameter range
Busy state or no-acceptable period
Timeout or no-acceptable period
Wrong data length
Password mismatch
(CR)
0x0d
4 bytes 1 byte
Technical Information
118
- ENGLISH
Appendix
Serial terminal
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface
specication, so that the projector can be controlled by a personal computer which is connected to this connector.
Connection
J
J
Pin assignments and signal names
D-Sub 9-pin (female)
Outside view
Pin No. Signal name Contents
NC
TXD Transmitted data
RXD Received data
Connected internally
GND Earth
NC
CTS
Connected internally
RTS
NC
D-Sub 9-pin (male)
Outside view
Pin No. Signal name Contents
NC
RXD Received data
TXD Transmitted data
NC
GND Earth
NC
RTS
Connected internally
CTS
NC
Communication conditions (Factory setting)
J
Signal level RS-232C-compliant Character length 8 bits
Sync. method Asynchronous Stop bit 1 bit
Baud rate 9 600 bps X parameter None
Parity None S parameter None
D-Sub 9-pin
(male)
D-Sub 9-pin
(male)
Communication cable
(straight)
D-Sub 9-pin
(female)
Connecting terminals
on projector 2
D-Sub 9-pin
(female)
D-Sub 9-pin
(male)
D-Sub 9-pin
(male)
D-Sub 9-pin
(female)
Connecting terminals
on projector 1
Communication cable
(straight)
Computer
●Multiple projectors
Computer
Communication cable
(straight)
D-Sub 9-pin (female)
D-Sub 9-pin (male)
Connecting terminals
on projector
●Single projector
Technical Information
ENGLISH -
119
Appendix
Basic format
J
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this
order. Add parameters according to the details of control.
STX A D I 1 I 2 ; C1 C2 C3 : P1 P2 Pn ETX
When sending commands without parameters, a colon (:) is not necessary.:
Û
Basic format (with sub command)
J
STX A D I 1 I 2 ; C1 C2 C3 : ETX
S1 S2 S3 S4 S5 E P1 P2 P3 P4 P5 P6
When transmitting a command which does not need a parameter, the operation (E) and parameter are not :
Û
necessary.
Attention
No command can be sent or received for 60 seconds after the lamp starts lighting. Try sending any command after that
z
period has elapsed.
When transmitting multiple commands, be sure to wait until 0.5 seconds has elapsed after receiving the response from the
z
projector before sending the next command.
Note
When the command can not be executed, the [ER401] status is sent from the projector to the personal computer.
z
When the wrong parameter is sent, the [ER402] status is sent from the projector to the personal computer.
z
Projector ID supported on the RS-232C interface is ZZ (ALL) and a group of 1 to 64 and 0A to 0Z.
z
If a command is sent with a projector ID specied, the projector will return answer back only in the following cases:
z
If it coincides with the projector ID
If the ID specication is ALL and responding (ID ALL) is [ON]
If the ID specication is Group and responding (ID Group) is [ON]
The “STX” character code is 02 and the “ETX” character code is 03.
z
End
(1 byte)
Parameter
(undened length)
Colon
(1 byte)
3 command
characters
(3 bytes)
Semicolon
(1 byte)
2 ID
characters
(2 bytes)
ID designate
ZZ, 1 to 64 and 0A to 0Z
(2 bytes)
Start
(1 byte)
Parameter (6 bytes)
Symbol “+” or “
-
” (1 byte) and set value or
adjustment value (5 bytes)
Operation (1 byte)
“=” (Value specied using parameter is set)
Same as basic format
Sub command (5 bytes)
Technical Information
120
- ENGLISH
Appendix
Cable specications
J
<When connected to a computer>
Projector
1 NC NC 1
Computer (DTE
specications)
2 2
3 3
4 NC NC 4
5 5
6 NC NC 6
7 7
8 8
9 NC NC 9
J
Control commands
When controlling the projector from a computer, the following commands are available:
<Projector control command>
Command Control contents Notes
PON Power [ON]
To see if the power is [ON], use the [Power query] command.
POF Power [OFF]
QPW Power query 000 = Standby 001 = Power [ON]
IIS Switch input modes
VID = VIDEO SVD = S-VIDEO RG1 = RGB1 RG2 = RGB2
DVI = DVI-D SDI = SDI (PT-DZ110XE/PT-DS100XE only) HD1 = HDMI
QSL
Query for active
lamp mode
0 = DUAL 1 = SINGLE 2 = LAMP1 3 = LAMP2
Û
[SINGLE] will use the lamp (LAMP 1 or LAMP 2) with shorter operating hours.
LPM Active lamp mode
0 = DUAL 1 = SINGLE 2 = Only LAMP1 is on 3 = Only LAMP2 is on
Û
[SINGLE] will use the lamp (LAMP1 or LAMP2) with shorter operating hours.
OLP Lamp power setting 0 = HIGH 1 = LOW
QLP
Query for lamp
output setting
0 = HIGH 1 = LOW
Q$L
Query for lamp
usage time
1 = LAMP1 2 = LAMP2
Response is 0000 - 3000
(Unit in hours: Number of equivalent hours for lamp output being set to [HIGH])
OSH Shutter 0 = End 1 = Execute
QSH
Query for shutter
state
0 = End 1 = Execute
VSE Switch aspect
0 = DEFAULT/VID AUTO/VID AUTO (PRI.) 1 = 4 : 3 2 = 16 : 9 5 = THROUGH
6 = HV FIT 9 = H FIT 10 = V FIT 20 = S1 AUTO 30 = VID AUTO
QSE
Query for aspect
setting
0 = DEFAULT/VID AUTO/VID AUTO (PRI.) 1 = 4 : 3 2 = 16 : 9 5 = THROUGH
6 = HV FIT 9 = H FIT 10 = V FIT 20 = S1 AUTO 30 = VID AUTO
OPP Execute P IN P 0 = OFF 1 = USER1 2 = USER2 3 = USER3
QPP
Query for P IN P
setting
0 = OFF 1 = USER1 2 = USER2 3 = USER3
QFI Query for lter 6 = Residual (ratio), Response is 000 - 100 (Unit: %)
OCS Switch sub memory 01 - 96 = Sub memory number
QSB
Query for sub
memory state
01 - 96 = Sub memory number
<Lens control command>
Command Sub command Contents Remarks
VXX LNSI2 Lens H shift
+00000 = Fine adjustment 1+, +00001 = Fine adjustment 1
-
,
+00100 = Fine adjustment 2+, +00101 = Fine adjustment 2
-
,
+00200 = Rough adjustment +, +00201 = Rough adjustment
-
VXX LNSI3 Lens V shift
VXX LNSI4 Lens focus
VXX LNSI5 Lens zoom
Technical Information
ENGLISH -
121
Appendix
REMOTE 2 IN terminal
Using the [REMOTE 2 IN] terminal provided on the connection terminals of the main unit, it is possible to operate
the projector from a control panel etc. furnished in a distant location where infrared remote control signal cannot
be received.
J
Pin assignments and control
D-Sub 9-pin (Outside view)
Pin No. Signal name Open (H) Short (L)
GND GND
POWER OFF ON
RGB1 Other RGB1
RGB2 Other RGB2
VIDEO Other VIDEO
S-VIDEO Other S-VIDEO
DVI Other DVI
SHUTTER OFF ON
RST/SET
Controlled by
remote control
Controlled by
external contact
Attention
Be sure to short-circuit Pins
z
and when controlling.
When pin
z
and pin are short-circuited, the following buttons on the projector's control panel and on the remote control
cannot be used.
<POWER ON ( I )> button, <SHUTTER> button
In addition, the RS-232C commands and network functions that correspond to these functions cannot be used either.
When pin
z
and pin are short-circuited and then any one of pins to is short-circuited to pin , the following buttons
on the projector's control panel and on the remote control cannot be used.
<POWER> button, <INPUT SELECT> buttons (RGB1, RGB2, DVI-D, SDI, VIDEO, S-VIDEO), <SHUTTER> button
In addition, the RS-232C commands and network functions that correspond to these functions cannot be used either.
The above is explanation in the case where “REMOTE2 MODE” of “PROJECTOR SETUP”
z
(
Æ
page 85) is set to
“STANDARD”.
S-VIDEO
VIDEO
DVI-D
RGB2
Control panel located in a different room
LAMP
ON
RGB1
Standby
External control
Remote control/External control
Remote control
Projector set up in a meeting room
Technical Information
122
- ENGLISH
Appendix
Two window display combination list
Subwindow
Main window
RGB1 RGB2
VIDEO
input
S-
VIDEO
input
DVI HDMI
*3
SDI
RGB
input
YP
B
P
R
input
RGB
input
YP
B
P
R
input
*1
Moving
image
system
*2
RGB
system
*1
Moving
image
system
*2
RGB
system
RGB1
RGB input
YP
B
P
R
input
RGB2
RGB input
YP
B
P
R
input
VIDEO input
S-VIDEO input
DVI
Moving image
system
*1
RGB
system
*2
HDMI
Moving image
system
*1
RGB
system
*2
SDI
*3
: P IN P (Picture in Picture) combination is possible
: P IN P (Picture in Picture) combination is impossible
Only 480p, 576p, 720/60p, 720/50p, 1 080/60i, 1 080/50i, 1 080/24sF, 1 080/24p, 1 080/25p, 1 080/30p, *1 :
1 080/50p, and 1 080/60p are supported.
VGA (640 × 480) - WUXGA (1 920 × 1 200)*2 :
non-interlace signal, Dot clock frequency : 25 MHz - 162 MHz
(The WUXGA signals support only VESA CVT-RB (Reduced Blanking) signals.)
PT-DZ110XE/PT-DS100XE only*3 :
Note
If the horizontal resolution of the input signal of the sub window is 1 280 pixels or above, the picture quality of the sub
z
window may be lowered.
Restoring the MENU LOCK PASSWORD to default
Press <AUTO SETUP> button for more than 2 seconds.
Press ▼ for more than 2 seconds.
Technical Information
ENGLISH -
123
Appendix
List of compatible signals
The following table species the types of signals compatible with the projector.
Format : V = VIDEO, S = S-VIDEO, D = DVI, H : HDMI, R : RGB, Y : YP
B
P
R
, SDI
Û
Mode
Display resolution
(dots)
Scanning
frequency
Dot clock
frequency
(MHz)
Format
PnP
*1
H
(kHz)
V
(Hz)
RGB2
DVI-D
EDID1
DVI-D
EDID2
DVI-D
EDID3
HDMI
NTSC/NTSC4.43/
PAL-M/PAL60
720 × 480i 15.7 59.9 V/S
PAL/PAL-N/SECAM 720 × 576i 15.6 50.0 V/S
525i (480i) 720 × 480i 15.7 59.9 13.5 R/Y/SDI
625i (576i) 720 × 576i 15.6 50.0 13.5 R/Y/SDI
525p (480p) 720 × 483 31.5 59.9 27.0 D/H/R/Y
625p (576p) 720 × 576 31.3 50.0 27.0 D/H/R/Y
1 125 (1 080)/60i
*2
1 920 × 1 080i 33.8 60.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/50i 1 920 × 1 080i 28.1 50.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/24p 1 920 × 1 080 27.0 24.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/24sF 1 920 × 1 080i 27.0 24.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/25p 1 920 × 1 080 28.1 25.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/30p 1 920 × 1 080 33.8 30.0 74.3 D/H/R/Y/SDI
1 125 (1 080)/60p 1 920 × 1 080 67.5 60.0 148.5 D/H/R/Y
1 125 (1 080)/50p 1 920 × 1 080 56.3 50.0 148.5 D/H/R/Y
750 (720)/60p 1 280 × 720 45.0 60.0 74.3 D/H/R/Y/SDI
750 (720)/50p 1 280 × 720 37.5 50.0 74.3 D/H/R/Y/SDI
VESA400
640 × 400 31.5 70.1 25.2 D/H/R
640 × 400 37.9 85.1 31.5 D/H/R
VGA480
640 × 480 31.5 59.9 25.2 D/H/R
640 × 480 35.0 66.7 30.2 D/H/R
640 × 480 37.9 72.8 31.5 D/H/R
640 × 480 37.5 75.0 31.5 D/H/R
640 × 480 43.3 85.0 36.0 D/H/R
SVGA
800 × 600 35.2 56.3 36.0 D/H/R
800 × 600 37.9 60.3 40.0 D/H/R
800 × 600 48.1 72.2 50.0 D/H/R
800 × 600 46.9 75.0 49.5 D/H/R
800 × 600 53.7 85.1 56.3 D/H/R
MAC16 832 × 624 49.7 74.6 57.3 D/H/R
XGA
1 024 × 768 39.6 50.0 51.9 D/H/R
1 024 × 768 48.4 60.0 65.0 D/H/R
1 024 × 768 56.5 70.1 75.0 D/H/R
1 024 × 768 60.0 75.0 78.8 D/H/R
1 024 × 768 65.5 81.6 86.0 D/H/R
1 024 × 768 68.7 85.0 94.5 D/H/R
1 024 × 768 80.0 100.0 105.0 D/H/R
1 024 × 768 96.7 120.0 130.0 D/H/R
MXGA
1 152 × 864 53.7 60.0 81.6 D/H/R
1 152 × 864 64.0 71.2 94.2 D/H/R
1 152 × 864 67.5 74.9 108.0 D/H/R
1 152 × 864 76.7 85.0 121.5 D/H/R
MAC21 1 152 × 870 68.7 75.1 100.0 D/H/R
1 280 × 720
1 280 × 720 37.1 49.8 60.5 D/H/R
1 280 × 720 44.8 59.9 74.5 D/H/R
1 280 × 768
1 280 × 768 39.6 49.9 65.3 D/H/R
1 280 × 768 47.8 59.9 79.5 D/H/R
1 280 × 768
*3
47.4 60.0 68.3 D/H/R
1 280 × 768 60.3 74.9 102.3 D/H/R
1 280 × 768 68.6 84.8 117.5 D/H/R
PT-DZ110XE/PT-DS100XE only:
Û
Technical Information
124
- ENGLISH
Appendix
Mode
Display resolution
(dots)
Scanning
frequency
Dot clock
frequency
(MHz)
Format
PnP
*1
H
(kHz)
V
(Hz)
RGB2
DVI-D
EDID1
DVI-D
EDID2
DVI-D
EDID3
HDMI
1 280 × 800
1 280 × 800 41.3 50.0 68.0 D/H/R
1 280 × 800 49.7 59.8 83.5 D/H/R
1 280 × 800
*3
49.3 59.9 71.0 D/H/R
1 280 × 800 62.8 74.9 106.5 D/H/R
1 280 × 800 71.6 84.9 122.5 D/H/R
MSXGA 1 280 × 960 60.0 60.0 108.0 D/H/R
SXGA
1 280 × 1 024 52.4 50.0 88.0 D/H/R
1 280 × 1 024 64.0 60.0 108.0 D/H/R
1 280 × 1 024 72.3 66.3 125.0 D/H/R
1 280 × 1 024 78.2 72.0 135.1 D/H/R
1 280 × 1 024 80.0 75.0 135.0 D/H/R
1 280 × 1 024 91.1 85.0 157.5 D/H/R
1 366 × 768
1 366 × 768 47.7 59.8 84.8 D/H/R
*4
*4
*4
*4
1 366 × 768 39.6 49.9 69.0 D/H/R
SXGA+
1 400 × 1 050 54.1 50.0 99.9 D/H/R
1 400 × 1 050 64.0 60.0 108.0 D/H/R
1 400 × 1 050 65.2 60.0 122.6 D/H/R
1 400 × 1 050 65.3 60.0 121.8 D/H/R
1 400 × 1 050 78.8 72.0 149.3 D/H/R
1 400 × 1 050 82.2 75.0 155.9 D/H/R
WXGA+
1 440 × 900 55.9 59.9 106.5 D/H/R
1 440 × 900 46.3 49.9 86.8 D/H/R
UXGA60 1 600 × 1 200 75.0 60.0 162.0 D/H/R
WSXGA+
1 680 × 1 050 65.3 60.0 146.3 D/H/R
1 680 × 1 050 54.1 50.0 119.5 D/H/R
1 920 × 1 080
1 920 × 1 080 55.6 49.9 141.5 D/H/R
1 920 × 1 080
*3
66.6 59.9 138.5 D/H/R
1 920 × 1 080
*6
67.2 60.0 173.0 R
WUXGA
1 920 × 1 200 61.8 49.9 158.3 D/H/R
1 920 × 1 200
*3
74.0 60.0 154.0 D/H/R
*5
*5
1 920 × 1 200
*6
74.6 59.9 193.3 R
Where marked “*1 : ” signals indicates in Plug and Play is compatible with EDID of projector. Unmarked
signals in Plug and Play may also be compliant if input terminals are written in the format list. Where Plug
and Play is unmarked and nothing is written in the format list, difculties in projecting image may occur even
when computer and projector appear to have same resolution.
If a signal of 1 125 (1 035)/60i is input, it will be displayed as a signal of 1 125 (1 080)/60i.*2 :
VESA CVT-RB (Reduced Blanking) compatible.*3 :
PT-DW90XE only*4 :
PT-DZ110XE only*5 :
Some loss of data occurs to make projection easier.*6 :
Note
The number of display dots of the PT-DZ110XE is 1 920 × 1 200, and the number of display dots of the PT-DS100XE is
z
1 400 × 1 050.
A signal of a different resolution than the above data is converted to the number of display dots and then displayed.
The “i” appearing after the resolution indicates an interlaced signal.
z
Flicker (line icker) may be caused in images if interlace is connected.
z
Specications
ENGLISH -
125
Appendix
Specications
Model No. PT-DZ110XE PT-DS100XE PT-DW90XE
Power supply AC220 V-240V 50 Hz/60 Hz
Power consumption
920 W 900 W
When [STANDBY MODE] is [ECO] : Approx. 0.3 W
When [STANDBY MODE] is [NORMAL] : Approx. 8 W
Amps 5.0 A 4.8 A
DLP chip
Panel size
24.4 mm (0.96")
(aspect ratio 16 : 10)
24.1 mm (0.95")
(aspect ratio 4 : 3)
21.6 mm (0.85")
(aspect ratio 16 : 9)
Display system Three-unit DLP chip, DLP type
Number of pixels
2 304 000 pixels
(1 920 × 1 200 dots) × 3
1 470 000 pixels
(1 400 × 1 050 dots) × 3
1 049 088 pixels
(1 366 × 768 dots) × 3
Lens Option
Projection lamp 2 bulbs × 355 W UHM lamp
Optical output
*1
10 600 lm (ANSI) 9 600 lm (ANSI)
*2
Applicable
scanning
frequency
For RGB signal
H : 15 kHz - 100 kHz, V : 24 Hz - 120 Hz
PIAS (Panasonic Intelligent Auto Scanning) system
Dot clock frequency
Less than 162 MHz
For YP
B
P
R
signal
[480i]
[480p]
[720/50p]
[1 035/60i]
[1 080/60i]
[1 080/25p]
[1 080/30p]
[1 080/50p]
H: 15.73 kHz,
H: 31.5 kHz,
H: 37.5 kHz,
H: 33.75 kHz,
H: 33.75 kHz,
H: 28.13 kHz,
H: 33.75 kHz,
H: 56.25 kHz,
V: 59.94 Hz
V: 59.94 Hz
V: 50 Hz
V: 60 Hz
V: 60 Hz
V: 25 Hz
V: 30 Hz
V: 50 Hz
[576i]
[576p]
[720/60p]
[1 080/50i]
[1 080/24p]
[1 080/24sF]
[1 080/60p]
H: 15.63 kHz,
H: 31.25 kHz,
H: 45 kHz,
H: 28.13 kHz,
H: 27 kHz,
H: 27 kHz,
H: 67.5 kHz,
V: 50 Hz
V: 50 Hz
V: 60 Hz
V: 50 Hz
V: 24 Hz
V: 48 Hz
V: 60 Hz
HD/SYNC, VD terminals are not compliant with 3 value composite SYNC.
z
For video signal
(S-video
included)
H : 15.75 kHz/15.63 kHz, V : 50 Hz/60 Hz
For DVI-D/HDMI
signal
480p, 576p, 720/60p, 720/50p, 1 080/60p, 1 080/50p, 1 080/60i, 1 080/50i, 1 080/24sF, 1 080/30p,
1 080/25p, 1 080/24p
Displayable resolution : VGA - WUXGA (non-interlace)
z
Dot clock frequency : 25 MHz - 162 MHz
z
For SDI signal
SMPTE259M compatible: [480i], [576i]
SMPTE292M compatible: [720/60p], [720/50p], [1 035/60i],
[1 080/60i], [1 080/50i], [1 080/25p],
[1 080/24p], [1 080/24sF], [1 080/30p]
Color system 7 standards (NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM/PAL60)
Screen size 1 778 mm - 15 240 mm (70" - 600")
*3
Screen aspect ratio 16 : 10 4 : 3 16 : 9
Projection scheme Menu-selectable from front/rear/ceiling mount, and oor mounting
Contrast ratio 10 000 : 1 (when [DYNAMIC IRIS] has been set to [3])
Terminals
RGB1 IN
1 set, BNC × 5
[RGB signal] 0.7 V [p-p]
HD/SYNC
VD
75 Ω (G-SYNC : 1.0 [p-p] 75 Ω)
TTL high impedance, automatic positive/negative polarity compatible
TTL high impedance, automatic positive/negative polarity compatible
[YP
B
P
R
signal] Y : 1.0 V [p-p] Synchronization signal included, P
B
P
R
: 0.7 V [p-p] 75 Ω
RGB2 IN
1 set of high density, D-sub 15-pin (female)
[RGB signal] 0.7 V [p-p]
HD/SYNC
VD
75 Ω (G-SYNC : 1.0 [p-p] 75 Ω)
TTL high impedance, automatic positive/negative polarity compatible
TTL high impedance, automatic positive/negative polarity compatible
[YP
B
P
R
signal] Y : 1.0 V [p-p] Synchronization signal included, P
B
P
R
: 0.7 V [p-p] 75 Ω
Specications
126
- ENGLISH
Appendix
Model No. PT-DZ110XE PT-DS100XE PT-DW90XE
Terminals
VIDEO IN 1 set, BNC, 1.0 V [p-p] 75 Ω
S-VIDEO IN 1 set, Mini DIN 4-pin, Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω, compatible with S1 signal
DVI-D IN 1 set, DVI-D 24-pin (Single link), DVI 1.0 compatible, HDCP compatible
HDMI IN 1 set, HDMI 19-pin (HDCP/Deep color compatible)
SDI IN
1 set, BNC, Y/CB/CR/4 : 2 : 2, 10 bits
SMPTE259M/SMPTE292M compatible
SERIAL IN/OUT 1 set, D-sub 9-pin, RS-232C compatible, computer control use
REMOTE 1
IN/OUT
1 set, M3 pin jack, wired remote control use, multiple connection use
REMOTE 2 IN 1 set, D-sub 9-pin, external control use
LAN 1 set, RJ-45, network connection use, PJLink compatible, 10 Base-T/100Base-TX
Power cord length 3.0 m
Cabinet Moulded plastic
Dimensions
Width : 530 mm (20 7/8"), Length : 200 mm (7 7/8"),
Height : 548.5 mm (21 19/32") (540 mm (21 1/4") : not including surface projection parts)
Weight Approx. 24.0 kg (52.9 lbs.)
*4
Operating environment
Temperature
*5
: 0 °C to 45 °C
Humidity : 10 % to 80 % (no condensation)
Remote
control
Power supply DC 3 V (AA/R6 battery × 2)
Operating range Approx. 30 m (98'5") (when operated directly in front of signal receptor)
Weight 134 g (4.7 ozs.) (including batteries)
Dimensions Width : 51 mm (2"), Length : 176 mm (6 15/16"), Height : 28 mm (1 3/32")
Options
Ceiling bracket
For high ceiling : ET-PKD310H
For low ceiling : ET-PKD310S
Ceiling Mount Attachment : ET-PAD310
Projection lens
ET-D75LE6, ET-D75LE1, ET-D75LE2, ET-D75LE3, ET-D75LE4
ET-D75LE5, ET-D75LE8
ET-D75LE10, ET-D75LE20, ET-D75LE30
Lens Motor
Cover
ET-D75MC1
Replacement
Lamp Unit
ET-LAD310 (1 bulb), ET-LAD310W (2 bulbs)
Replacement
lter unit
ET-ACF310
Smoke Cut Filter ET-SFD310
Frame ET-PFD310
Measurement, measuring conditions and method of notation all comply with ISO21118 international *1 :
standards.
For details of video signals that can be projected using this projector, refer to *2 : “List of compatible signals”
(
Æ
page 123).
If ET-D75LE5 is installed, screen size is 1 778 mm - 7 620 mm (70" - 300").*3 :
This is the average value. It may differ depending on each product.*4 :
When using this projector at high elevations 1 400 - 2 700 m (4 593 - 8 858 ft) sea level, temperature will be *5 :
5 °C lower than this higher limit.
When a Smoke Cut Filter is used, the ambient temperature is 0 °C to 35 °C. However, use at high altitudes
is not possible.
The part numbers of accessories and separately sold components are subject to change without notice.
z
Specications
ENGLISH -
127
Appendix
Specications
Trademark Acknowledgement
Microsoft
z
®
and its logos, Windows
®
, Windows
®
XP, Windows Vista
®
, Windows
®
7, and Internet Explorer
®
are the registered trademarks or trademarks of Microsoft Corporation in the United States and/or other
countries.
Macintosh, Mac OS and Safari are the trademarks of Apple Inc. registered in the United States and other
z
countries.
PJLink™ is a pending trademark in Japan, the United States, and other countries and regions.
z
HDMI, the HDMI logo and High-Denition Multimedia Interface are the trademarks or registered trademarks
z
of HDMI Licensing LLC.
Other types of names such as company names and product names appearing in this instruction manual are
z
trademarks or registered trademarks of their respective holders.
The ® and TM marks are not indicated in this instruction manual.
<Unit : mm>
Dimensions
About brand
8.5 (11/32")
540 (21 - 1/4")
462 (18 - 7/32")
530 (20 - 7/8")
200 (7 - 7/8")
100 (3 - 15/16")
468 (18 - 7/16")26 (1 - 1/32")
128
- ENGLISH
Appendix
Ceiling mount bracket safeguards
When installing the ceiling mount bracket to the projector, install the accessory Drop-prevention bracket (Safety
cables) to the projector.
(The projector will still be safe if they are not used, however they will help prevent the possibility of accidents
caused by the projector falling down if the screws happen to become loose.)
Ceiling bracket : For high ceiling : ET-PKD310H, For low ceiling : ET-PKD310S,
Ceiling Mount Attachment : ET-PAD310
Installation work of the ceiling mount bracket should only be carried by a
qualied technician according to the following procedure.
Panasonic takes no responsibility for any losses or damage occurring as a result of using a ceiling mount
z
bracket not manufactured by Panasonic, or if damage to the projector occurs as a result of an inappropriate
location used for installing the ceiling mount bracket, even if the projector’s warranty period has not yet expired.
Use a torque screwdriver or similar tool to tighten the screws. Do not use tools such as electric screwdrivers or
z
impact screwdrivers.
An unused ceiling mount bracket should be removed promptly by qualied technician.
z
Do not use the screw holes of the front leg adjusters for the projector installation.
z
Do not attach the safety cable to the burglar hook port and suspend the projector on it.
z
For how to install wire ropes to the ceiling, see the installation manual for the ceiling mount bracket.
z
For details, see the installation manual for the ceiling mount bracket.
z
The part numbers of accessories and separately sold components are subject to change without notice.
z
Attachment procedure
Turn the projector upside down and 1 )
place it gently on a soft cloth.
Put the plain washer on the wire rope 2 )
xing screw.
Put the wire rope through the wire rope 3 )
xing screw.
Install the wire rope xing screws to the 4 )
projector and tighten them.
Install the wire ropes to the 2 places in a similar
z
manner.
Wire rope xing screw: M6 x L20.
Tightening torque of xing screw: 4 ± 0.5 Nm
Attention
Do not use other than the provided Wire rope xing screw (x2), washers (x4) and Safety cables (x2).
z
Install the wire ropes so that they do not sag between the installation portions on the body and those on the ceiling.
z
Ceiling bracket
(Metal tting attached to the ceiling mount bracket or projector
metal tting for the ceiling mount bracket)
Wire rope
Positions to install
wire ropes to body
Plain washer
Wire rope xing screw
Washer
Please also attach the washer
which is additional accessory to
the ceiling mount.
Ceiling mount
ENGLISH -
129
Appendix
Index
A
About brand ..................................127
Accessories ....................................17
ADVANCED MENU ........................64
ASPECT .........................................59
AUTO SETUP .................................72
AUTO SETUP function ...................48
AUTO SIGNAL................................72
B
BACK COLOR ................................75
BLANKING .....................................64
BRIGHTNESS ................................54
BRIGHTNESS CONTROL ..............78
C
Ceiling mount bracket ...................128
CLAMP POSITION .........................65
CLOCK PHASE ..............................61
COLOR ...........................................54
COLOR MATCHING .......................69
COLOR TEMPERATURE ...............55
Connecting
AV equipment ..........................36
Before connection to the
projector ..............................35
Computers ..............................37
Connecting the power cord.............39
CONTRAST ....................................54
Control commands via LAN ..........116
CONTROL DEVICE SETUP ...........94
COOLING CONDITION ..................77
D
DATE AND TIME ............................85
DIGITAL CINEMA REALITY ...........64
Dimensions ...................................127
Direct power off function .................41
Display language ............................68
DISPLAY LANGUAGE menu ..........68
DISPLAY OPTION menu ................69
DISPLAY SETTING ........................93
DVI-D IN .........................................73
DYNAMIC IRIS ...............................57
E
EDGE BLENDING ..........................65
F
FILTER COUNTER RESET ............86
FILTER indicator ...........................109
FOCUS
Adjusting .................................42
FRAME DELAY ..............................67
FREEZE .........................................75
Front leg adjusters ..........................34
FUNCTION ...............................48, 85
G
GAMMA ..........................................56
GEOMETRY ...................................61
H
HDMI IN ..........................................74
HIGH ALTITUDE MODE .................76
I
Important Safety Notice ....................2
INITIALIZE ......................................87
INPUT RESOLUTION ....................65
Input signal .....................................47
INSTALLATION ..............................76
Internal test pattern.........................48
K
KEYSTONE ....................................63
L
LAMP indicator .............................108
LAMP POWER ...............................78
LAMP RELAY .................................77
LAMP SELECT ...............................77
LARGE SCREEN CORRECTION
.....70
LENS CALIBRATION .....................86
Lens position ..................................43
List of compatible signals .............123
LOAD ALL USER DATA ..................87
M
MAIN MENU ...................................51
Managing the indicated problems
...108
MENU LOCK ..................................93
MENU LOCK PASSWORD ..........122
Menu Navigation.............................50
N
Navigating through the menu .........50
NETWORK menu ...........................95
NOISE REDUCTION ......................57
NO SIGNAL SHUT-OFF .................85
O
On-screen display.....................47, 74
P
Picture Aspect ratio.........................49
PICTURE menu ..............................53
PICTURE MODE ............................53
P IN P function ................................88
P IN P menu ...................................88
PJLink protocol .............................115
POSITION menu ............................59
Powering off the projector ...............41
Powering up the projector...............40
Precautions with regard to safety .....9
Projecting........................................42
Projection lens ................................38
Projection method...........................22
Projector body ................................19
PROJECTOR ID .............................76
PROJECTOR SETUP menu ..........76
R
RASTER POSITION .......................67
REMOTE 2 IN terminal .................121
REMOTE2 MODE ..........................85
Remote control ...............................18
Replacement ................................110
RGB IN ...........................................73
RS-232C .........................................83
S
SAVE ALL USER DATA ..................87
SCHEDULE ....................................82
SCREEN SETTING ........................70
Screen size and throw distance......23
SDI IN .............................................74
SECURITY menu ...........................92
SECURITY PASSWORD ................92
Selecting the input signal................42
Serial terminal...............................118
SERVICE PASSWORD ..................87
Setting projector ID number to
remote control .............................21
Setting up .......................................22
SHARPNESS .................................57
SHIFT .............................................59
SHUTTER function .........................47
SIGNAL LIST ..................................90
Registering a signal ................90
SIGNAL LIST menu ........................90
Specications ...............................125
STANDBY MODE ...........................82
STARTUP LOGO ............................75
STATUS ..........................................84
STATUS function ............................47
Sub memory ...................................91
SUB MENU .....................................51
SYSTEM DAYLIGHT VIEW ............56
SYSTEM SELECTOR ....................58
T
Technical Information....................115
TEMP indicator .............................109
TEST PATTERN .............................89
TEST PATTERN menu ...................89
TINT ................................................54
Troubleshooting ............................113
Two window display combination
....122
W
WAVEFORM MONITOR .................71
Wired remote control ......................21
Z
ZOOM .............................................60
100

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic PT-DW90X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic PT-DW90X in de taal/talen: Engels als bijlage per email.

De handleiding is 12,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Panasonic PT-DW90X

Panasonic PT-DW90X Gebruiksaanwijzing - Deutsch - 130 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info