543723
122
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
122 - ENGLISH
Chapter 6 Appendix — Technical information
Sync. method Asynchronous
Baud rate 9 600 bps
Parity None
Character length 8 bit
Stop bit 1 bit
X parameter None
S parameter None
Basic format
Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according
to the details of control.
E\WHV
,'FKDUDFWHUV
E\WHV
6HPLFRORQ
E\WH
&RORQE\WH
&RPPDQG
FKDUDFWHUVE\WHV
3DUDPHWHU
XQGHILQHGOHQJWK
(QGE\WH
6WDUWE\WH
==±DQG$±=
,'VHWWLQJDUHD
Attention
rf
If a command is transmitted after the lamp starts illuminating, there may be a delay in response or the command may not be executed. Try
sending or receiving any command after 60 seconds.
rf
When transmitting multiple commands, be sure to wait until 0.5 seconds has elapsed after receiving the response from the projector before
sending the next command. When transmitting a command which does not need a parameter, a colon (:) is not necessary.
Note
rf
If a command cannot be executed, an “ER401” response is sent from the projector to the computer.
rf
If an invalid parameter is sent, an “ER402” response is sent from the projector to the computer.
rf
ID transmission in RS-232C supports ZZ (ALL) and 01 to 64, as well as 0A to 0Z groups.
rf
If a command is sent with a specied ID, a response will be sent to the computer only in the following cases.
rg
It matches the projector ID
rg
ID setting is set to ALL and [RESPONSE(ID ALL)] is [ON]
rg
ID setting is set to GROUP and [RESPONSE(ID GROUP)] is [ON]
rf
STX and ETX are character codes. STX shown in hexadecimal is 02, and ETX shown in hexadecimal is 03.
When multiple projectors are controlled
When multiple projectors are all controlled
When controlling multiple projectors together via RS-232C, perform the following settings.
1)
Set a different ID for each projector.
2)
Set [RESPONSE(ID ALL)] to [ON] in only one
projector.
3)
Set [RESPONSE(ID ALL)] to [OFF] for all other
projectors set in Step 2).
When multiple projectors are all controlled by group unit
When controlling multiple projectors by group unit via RS-232C, perform the following settings.
1)
Set a different ID for each projector.
2)
Set [RESPONSE(ID GROUP)] to [ON] in only
one projector.
3)
Set [RESPONSE(ID GROUP)] to [OFF] for all
other projectors set in Step 2).
Note
rf
There will be no response if 2 or more projectors have [RESPONSE(ID ALL)] set to [ON].
rf
There will be no response if 2 or more projectors of the same group have [RESPONSE(ID GROUP)] set to [ON].
rf
When setting multiple groups, set [RESPONSE(ID ALL)] to [ON] in only one projector in each group.
122

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic PT-DW640E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic PT-DW640E in de taal/talen: Engels als bijlage per email.

De handleiding is 16,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Panasonic PT-DW640E

Panasonic PT-DW640E Gebruiksaanwijzing - Deutsch - 140 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info