2
1.Earthing instructions
WARNING: THIS APPLIANCE MUST BE
EARTHED.
This appliance is supplied with a moulded three
pin mains plug for your safety and convenience.
A 13 amp fuse is fitted in this plug. Should the fuse
need to be replaced, please ensure that the
replacement fuse has a rating of 13 amps and
that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover, you
must ensure that it is refitted when the fuse is
replaced. If you lose the fuse cover, the plug must
not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from
your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS
UNSUITABLE FOR THE SOCKET OUTLET
THEN THE FUSE SHOULD BE REMOVED AND
THE PLUG CUT OFF AND DISPOSED OF
SAFELY AND AN APPROPRIATE ONE FITTED.
THERE IS A DANGER OF SEVERE
ELECTRICAL SHOCK IF THE CUT OFF PLUG
IS INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted, please observe the
wiring code as shown. If in any doubt, please
consult a qualified electrician.
IMPORTANT: The wires in mains lead are
coloured in accordance with the following code:
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured GREEN-AND-
YELLOW must be connected to the terminal in the
plug which is marked with the letter E or by the
Earth
symbol or coloured GREEN or GREEN-AND-
YELLOW.
The wire which is coloured BLUE must be
connected to the terminal in the plug which is
marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be
connected to the terminal in the plug which is
marked with the letter L or coloured RED.
How to replace the fuse
Open the fuse compartment with a screwdriver
and replace the fuse.
When an outlet is not earthed:
It is the personal responsibility and obligation of
the customer to have it replaced with a properly
earthed outlet.
2.Voltage and Power
The voltage used must be the same as specified
on the oven. Using a higher voltage than that
which is specified is dangerous, and may result in
a fire or other type of accident causing damage.
3.Service
It is dangerous for anyone other than a service
technician trained by the manufacturer to perform
repair service.
Do not remove the outer casing of the oven.
High voltages are present inside the cabinet.
Repairs and adjustments should be done only by
qualified service personnel. Contact the
manufacturer.
Door Seals
Do not attempt to tamper with or make any
adjustments or repairs to door, control panel
housing, safety interlock switches or any other part
of the oven. Do not remove outer panel from the
oven.
The door seals and door seal areas should always
be kept clean-use a damp cloth.
4.Operation when empty
The appliance must not be operated by
MICROWAVE or COMBINATION WITHOUT
FOOD IN THE OVEN. Operation when empty will
damage the appliance.
5.Cord
If the supply cord is damaged, it must be replaced
by the manufacture or its service agent or a
similarly qualified person in order to avoid a
hazard.
Do not immerse oven in water. Keep cord away
from heated surfaces. Do not let cord hang over
the edge of table or work top. The back of the
appliance heats up during use. Do not allow the
cord to be in contact with the back of the appliance
or cabinet surface.
6.Hot Surfaces
Exterior oven surfaces, including air vents on the
cabinet and the oven door will get hot during use.
(Grill, Convection and Combination) Take care
when opening or closing door and when inserting
or removing food and accessories.
The oven has heaters situated in the top and back
of the oven. After use, the roof, walls and floor will
be very hot.
7.Switching off.
In case of electronic failure, oven can only be
turned off at outlet.
Safety Information
