502386
15
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
-
15
-
Installing Blade
Follow these steps:
1.Remove the battery pack from the metal cutter.
2.Remove any cutting debris from blade area.
3.Use the lower guard lift lever to retract (open)
the lower guard.
4.Install the blade as illustrated. (See Fig.12)
Make sure that both the direction arrow on the
blade and the direction arrow on the upper
blade cover point in the same direction.
5.Set the outer washer in place.
6.Insert the hex bolt.
7.Hold the spindle lock button down. This pre-
vents the blade from rotating.
8.Tighten the hex bolt securely with the provided
hex wrench. Store the hex wrench.
NOTE:
Keep the hex wrench in the storage slot on the
metal cutters body when not using it.
WARNING
Failure to follow these instructions can result
in serious personal injury.
For Appropriate use of Battery
pack
Ni-MH Battery pack (EY9251)
Charge the Ni-MH battery fully before storage
in order to ensure a longer service life.
The ambient temperature range is between 0°C
(32°F) and 40°C (104°F).
If the battery pack is used when the battery
temperature is below 0°C (32°F), the tool may
fail to function properly. In that case, charge the
battery until charging is completed for appropri-
ate functioning of the battery.
When battery pack is not in use, keep it away
from other metal objects like: paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal
to another.
Shorting the battery terminals together may
cause sparks, burns or a fire.
When operating with a Ni-MH battery pack,
make sure the place is well ventilated.
Battery Pack Life
The rechargeable batteries have a limited life. If
operation time becomes extremely short after
recharging, replace the battery pack with a new one.
NOTE:
•Use under extremely hot or cold conditions will
reduce operating capacity per charge.
•Even if you don’t use the Metal Cutter, charge
the battery pack at least once every six months.
Battery Recycling
ATTENTION:
•For environmental protection and recycling of
materials, be sure that it is disposed of at an
officially assigned location, if there is one in your
country.
Cleaning Metal Cutter
Keep your metal cutter clean for good cutting per-
formance, and to help keep it safe to use.
Follow these steps:
1.Remove the battery pack from the metal cutter.
2.Wipe the metal cutter with a dry, soft cloth. Do
not use a wet cloth or cleaning liquids.
They could damage the metal cutter’s finish.
3.Be sure to rub off any oil or grease which
could make the metal cutter slippery or hard to
handle.
4.Remove the blade and brush off any dust.
CAUTION:
To avoid injury or damage to the unit, never
immerse any part of the tool in a liquid.
Transparent Guard
WARNING
If the guard is cracked, or is broken, take the
metal cutter to an authorized service center
for replacement. Do not attempt to operate
cutter. It could result in serious personal injury.
Never use your metal cutter with a damaged
transparent guard or without the transparent
guard installed. Flying chips could result in
serious injury.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic EY3552 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic EY3552 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info