502386
12
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
-
12
-
Inserting Battery Pack
CAUTION:
Before inserting battery pack, check that the
power switch in the Metal Cutter actuates properly
and returns to the “OFF” position when released.
1.To insert the battery pack: (See Fig.2)
Slide the battery pack in place at the rear of
the metal cutter. The battery should snap into
place. If the battery is loose, it has not been
properly connected.
2.To remove the battery pack:
Press the two tabs on the sides of the battery
pack. Slide the battery pack out of the metal
cutter body.
IV. OPERATION
Before Using Metal Cutter
This tool is intended for cutting unhardened fer-
rous metal and nonferrous metal. Refer to the
“Accessories” section for a list of blades to be
used for the proper applications of this tool. The
following precautions must be followed to reduce
the risk of injury;
•Do not cut stacked materials. Cut one piece at a
time.
•Do not cut hardened steel.
•Cut materials with the wider edge of the shoe
over the clamped side of the material.
•Do not touch the saw blade, workpiece, or cutting
chips with bare hands immediately after cutting;
they may be hot and could burn skin.
Each time you use the metal cutter, you must
make sure it is in good operating condition.
Use the following checklist:
1.Is the blade installed in the correct direction?
The arrow on the blade must point in the same
direction as the arrow on the upper blade
cover.
2.Is the blade installed properly?
Make sure the hex bolt is tightened securely.
(See Fig.12)
3.Does the blade look alright?
Replace the blade immediately if there are any
cracks in it or if any teeth are broken.
4.Does the lower guard close properly?
WARNING
To avoid injury, do not use the metal cutter if
the lower guard does not close quickly over
the blade.
5.Is the transparent guard securely installed?
6.Is the battery pack charged and inserted firmly
to the metal cutter?
7.Is the depth adjustment lever for cutting
securely tightened?
8.Is the workpiece securely clamped on a saw
horse or bench?
Using Metal Cutter
CAUTION:
To reduce the risk of injury read the Safety
Instructions at the front of this manual before using
the metal cutter.
WARNING
To reduce the risk of injury, wear safety goggles
or glasses with side shields.
Follow these steps:
Hold the metal cutter with both hands. (See
Fig.4) Do not attempt to remove cut material
when blade is moving.
1.Line up the sight line on shoe with your cutting
line. (See Fig.3)
Alignment with cutting line
Use the notch as guide to establish cutting
position. Align the notch with cutting line.
As the cutting position may differ depending on
the blade, do a trial cut beforehand.
2.Press the switch lock lever down, then
squeeze the power switch to start the motor,
and then release the switch lock lever.
CAUTION:
Check that the switch lock lever works.
If power switch can be activated without
depressing the switch lock lever, discontinue
use immediately. Take the tool to an author-
ized service center.
Always hold the handle with one hand and the
front grip with the other. (See Fig.4) Maintain a
firm grip and depress the switch fully.
The blade should not touch the cutting mate-
rial before you start the motor. Wait until the
blade reaches full speed before starting a cut.
This tool has no provision to lock the power
switch in the “ON” position, and you must not
attempt to secure it in the “ONposition.
3.Start cutting when the blade reaches full
speed.
4.During cutting, keep your cutting line straight.
Move the metal cutter forward at a steady
speed, while looking at the tip of the blade
through the transparent guard.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic EY3552 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic EY3552 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info