502343
42
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
RQT9378
42
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart
do not solve the problem, refer to “Customer Services Directory (United States and Puerto Rico)” on page 46 if you reside in the U.S.A.and Puerto
Rico, or refer to “Product information” on page 48 if you reside in Canada.
The following do not indicate a problem with this unit:
Regular disc rotating sounds.
Image disturbance during search.
To reset this unit Page
Power
Operation
To restore the unit if it
freezes due to one of the
safety devices being
activated
Press and hold [POWER Í/I] on the main unit for 3 seconds. (The settings remain
unchanged.)
To return all settings to the
factory preset
Select “Yes” in “Restore Default Settings” in the Setup menu.
This returns all values in the Setup menu and the on-screen menu, except for “Remote
Control Code”, “On-screen Language”, “IP Address/DNS Settings”, “Proxy Server
Settings”, “DVD-Video Ratings”, “BD-Video Ratings” and “Network Service“ to the
default settings.
36
To return to the factory
preset
(No setting)
Reset the unit as follows:
1Press [POWER Í/I] on the unit to turn off the unit.
2 Press and hold [;], [POWER Í/I] and [< OPEN/CLOSE] on the unit at the
same time for more than 5 seconds until “HELLO” is displayed on the unit.
3 The power will turn on and then turn off.
Power of this unit is turned
off when the input for the TV
is switched.
If connected with an “HDAVI Control 4” compatible TV (VIERA) with the “Auto
power stand-by” setting activated on the TV, when switching the TV input, the unit
will be automatically turned to standby. For details please read the operating
instructions of the TV.
Cannot operate the
television or amplifier/
receiver.
The remote control doesn’t
work properly.
Change the manufacturer code of the remote control. In some cases, even if you
change the code, the remote control may not be operated depending on the type
of the televisions or amplifiers/receivers.
It may be necessary to set the manufacturer code or the remote control code
again after changing the batteries for remote control.
The remote control and main unit are using different codes. Change the code on
the remote control.
The batteries are depleted. Replace them with new ones.
15
5, 15, 36
36
5
The unit is on but cannot be
operated.
Confirm the correct drive is selected.
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [POWER
Í
/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [POWER
Í
/I] on the main unit for
about 3 seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.
2Press [POWER Í/I] on the main unit to switch it on. If the unit still cannot be
operated, consult the dealer.
Condensation has formed. Wait 1 to 2 hours for it to evaporate.
19
Play fails to start even when
[1] (PLAY) is pressed.
Play starts but then stops
immediately.
Insert the media correctly with the label facing up.
The media is dirty.
You tried to play a blank media or unplayable media on this unit.
[DivX]
: If playing DivX VOD content, refer to the homepage where you purchased it.
19
3
6, 7
26
Cannot eject disc. The unit may have a problem. While the unit is off, press and hold [;] and
[< OPEN/CLOSE] on the main unit at the same time for about 5 seconds to force
the tray to eject. Remove the disc and consult the dealer.
Start up is slow.
It takes time before play
starts.
Make sure that “Quick Start” is set to “On”. If connected with an HDAVI Control 4 compatible TV
(VIERA) with the “Stand-by power save” setting activated on the TV, even with “Quick Start” set
to “On”, when the TV is in standby mode, the unit may take some time to startup.
Start up takes time in the following situations.
–Immediately after a power failure or the AC power supply cord is connected.
–When the unit is connected with an HDMI cable.
[DivX]: This is normal on DivX video.
35
Played back image is
distorted or does not
playback correctly. ([AVCHD])
High definition video (transfer rate of 18 Mbps or faster) cannot be played back
correctly if it was recorded on a DVD compatible to double speed or slower.
Cannot set “On” in “24p
Output”.
Only when the unit is connected to the HDMI terminal of a TV supporting 24p you
can select “On”. In some cases where the unit is connected to a TV via an
amplifier/receiver through the HDMI terminals, you may not be able to select “On”.
In this case, connect the unit to a TV through the HDMI terminal and connect it to
the amplifier/receiver through any terminal other than HDMI.
34
DMP-BD80_60_601_605PP-RQT9378_ENG.book 42 ページ 2009年2月19日 木曜日 午後4時48分
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic DMP-BD60 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic DMP-BD60 in de taal/talen: Engels als bijlage per email.

De handleiding is 11,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Panasonic DMP-BD60

Panasonic DMP-BD60 Gebruiksaanwijzing - Nederlands - 104 pagina's

Panasonic DMP-BD60 Gebruiksaanwijzing - Deutsch, Italiano, Espanôl, Espanõl - 132 pagina's

Panasonic DMP-BD60 Gebruiksaanwijzing - Svenska - 104 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info