659194
3
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
Before use, please read these
instructions completely.
Digital Camera
Operating Instructions
Model No.
DMC-F7PP
VQT9757
For USA assistance, please call: 1-800-272-7033 or send e-mail to : consumerproducts@panasonic.com
For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca
KC4-PP.book 1 ページ 2002年1月21日 月曜日 午後7時51分
2
Dear Customer,
We would like to take this opportunity to
thank you for purchasing this Panasonic
Digital Camera. Please read these
Operating Instructions carefully and keep
them handy for future reference.
Information for
Your Safety
WARNING
TO REDUCE THE RISK OF FIRE OR
SHOCK HAZARD AND ANNOYING
INTERFERENCE, USE ONLY THE
RECOMMENDED ACCESSORIES AND
DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE. DO NOT
REMOVE THE COVER (OR BACK);
THERE ARE NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Notice:
This product has parts that contain a small
amount of mercury. It also contains lead in
some components. Disposal of these
materials may be regulated in your
community due to environmental
considerations. For disposal or recycling
information please contact your local
authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
Carefully observe copyright laws.
Recording of pre-recorded tapes or
discs or other published or broadcast
material for purposes other than your
own private use may infringe copyright
laws. Even for the purpose of private
use, recording of certain material may
be restricted.
Please note that the actual controls and
components, menu items, etc. of your
Digital Camera may look somewhat
different from those shown in the
illustrations in these Operating
Instructions.
SD Logo is a trademark.
Other names, company names, and
product names printed in these
instructions are trademarks or registered
trademarks of the companies
concerned.
During use, the camera becomes warm,
but it is not a malfunction.
KC4-PP.book 2 ページ 2002年1月21日 月曜日 午後7時51分
3
FCC Note: (U.S. only)
This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
FCC Caution: To assure continued
compliance, follow the
attached installation
instructions and use only
shielded interface cables
with ferrite core when
connecting to computer
or peripheral devices.
Any changes or
modifications not
expressly approved by
the party responsible for
compliance could void
the user’s authority to
operate this equipment.
Trade Name: Panasonic
Model No.: DMC-F7
Responsible party:Matsushita Electric
Corporation of
America One
Panasonic Way,
Secaucus, NJ 07094
Support Contact:Panasonic
Consumer
Electronics
Company 1-800-
272-7033
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
This Class [B] digital apparatus complies
with Canadian ICES-003.
Cet appareil num
é
rique de la classe [B]
est conforme
á
la norme NMB-003 du
Canada.
DMC-F7
KC4-PP.book 3 ページ 2002年1月21日 月曜日 午後7時51分
4
USB Driver End User License Agreement
You (
“Licensee”) are granted a license for the Software defined in this End User Soft
Agreement (“Agreement”) on condition that you agree to the terms and conditions of
this Agreement. If Licensee does not agree to the terms and conditions of this
Agreement, promptly return the Software to Matsushita Electric Industrial Co., Ltd
(“Matsushita”), its distributors or dealers from which you made the purchase.
Article 1 License
Licensee is granted the right to use the software, including the information recorded or
described on the CD-ROM, instruction manuals, and any other media provided to
Licensee (collectively “Software”), but all applicable rights to patents, copyrights,
trademarks and trade secrets in the Software are not transferred to Licensee.
Article 2 Use by a Third Party
Licensee may not use, copy, modify, transfer or allow any third party, whether free of
charge or not, to use, copy or modify the Software, except as expressly provided for in
this Agreement.
Article 3 Restrictions on Copying the Software
Licensee may make a single copy of the Software in whole or a part solely for back-up
purpose.
Article 4 Computer
Licensee may use the Software only on the computer, and may not use it on more than
one computer.
Article 5 Reverse Engineering, Decompiling or Disassembly
Licensee may not reverse engineer, decompile, or disassemble the Software, except to
the extent either of them is permitted under law or regulation of the country where
Licensee resides. Matsushita, or its distributors will not be responsible for any defects in
the Software or damage to Licensee caused by Licensee’s reverse engineering,
decompiling, or disassembly of the Software.
Article 6 Indemnification
The Software is provided “AS-IS” without warranty of any kind, either expressed or
implied, including, but not limited to, warranties of non-infringement, merchantability
and/or fitness for a particular purpose. Further, Matsushita does not warrant that the
operation of the Software will be uninterrupted or error free. Matsushita or any of its
distributors will not be liable for any damage suffered by Licensee arising from or in
connection with Licensee’s use of the Software.
Article 7 Export Control
Licensee agrees not to export or re-export to any country the Software in any form
without the appropriate export licenses under regulations of the country where Licensee
resides, if necessary.
Article 8 Termination of License
The right granted to Licensee hereunder will be automatically terminated if Licensee
contravenes of any of the terms and conditions of this Agreement. In the event, Licensee
must destroy the Software and related documentation together with all the copies thereof at
Licensee’s own expense.
KC4-PP.book 4 ページ 2002年1月21日 月曜日 午後7時51分
5
Contents
Safety
Information for Your Safety ......................................................................................2
USB Driver End User License Agreement ...............................................................4
Preparation
Components.............................................................................................................7
Names of the Components ......................................................................................8
LCD Monitor Display .............................................................................................. 10
Quick Guide ...........................................................................................................12
Inserting the Battery............................................................................................... 13
Charging the Battery ..............................................................................................14
Connecting to an Electrical Outlet..........................................................................15
Inserting the Card ..................................................................................................16
Turning Power on/off..............................................................................................18
Attaching the Strap ................................................................................................19
Using the Tripod.....................................................................................................20
Using the LCD Monitor........................................................................................... 21
The Indicators ........................................................................................................22
The Shutter Button (Pressing halfway/Pressing fully)............................................23
Operating the Menu ...............................................................................................24
Setting the Date/Time (Clock Set) .........................................................................25
Recording images (basic)
Taking Pictures ...................................................................................................... 26
Checking the Last Picture (Review).......................................................................27
Recording Motion Images ...................................................................................... 28
Using the Optical Zoom ......................................................................................... 29
Using the Digital Zoom...........................................................................................30
Taking Pictures with the Built-in Flash ...................................................................31
Taking Pictures with the Self-timer ........................................................................ 33
Recording images (advanced)
Changing the Picture Size .....................................................................................34
Changing the Quality (Data Compression Ratio) ...................................................35
Compensating the Exposure..................................................................................36
Using the AF/AE Lock............................................................................................37
Using the Spot AF..................................................................................................38
Setting the White Balance......................................................................................39
Setting ISO Sensitivity ...........................................................................................41
Taking Pictures with Macro Mode/Unlimited Recording.........................................42
Taking Pictures with Burst Mode ...........................................................................43
KC4-PP.book 5 ページ 2002年1月21日 月曜日 午後7時51分
6
Playback
Playing Back Still Pictures .....................................................................................44
9 Images Multi Playback ........................................................................................45
Using the Playback Zoom ...................................................................................... 46
Editing the Recorded Pictures ............................................................................... 47
Adding the Date .....................................................................................................48
Playing Back Motion Images.................................................................................. 49
Editing
Deleting Images ..................................................................................................... 50
Writing the Print Information in the Card (DPOF Setting) ......................................52
Protecting Images on the Card ..............................................................................55
Technical use
Playing Back with Slide Show (Automatic Playback).............................................56
Formatting the Card ...............................................................................................57
Adjusting the LCD Monitor Brightness ...................................................................58
Using the Auto Review........................................................................................... 59
Setting up the Beep Sound .................................................................................... 60
Setting up the Power Save Mode ..........................................................................61
Resetting the File Number .....................................................................................62
Memorizing settings ............................................................................................... 63
Playing Back Images with TV Monitor ................................................................... 64
After Use ................................................................................................................ 65
Connecting to PC ...................................................................................................66
Others
The Menu Items .....................................................................................................67
Cautions for Use ....................................................................................................69
Warning Indication ................................................................................................. 73
Troubleshooting .....................................................................................................74
Specifications.........................................................................................................75
Digital Camera Accessory System.........................................................................77
Digital Camera Accessory Order Form ..................................................................78
Request for Service Notice .................................................................................... 79
Limited Warranty....................................................................................................80
Warranty ................................................................................................................82
Servicenter List ...................................................................................................... 84
Index ...................................................................................................................... 85
Spanish Quick Use Guide/Guía española para el uso rápido................................ 86
KC4-PP.book 6 ページ 2002年1月21日 月曜日 午後7時51分
7
Components
Before using your camera, check the contents.
1
SD Memory Card (8MB)
RP-SD008
2
Battery Pack
CGA-S101A
3
AC Adaptor
DE-873D
4
USB Connection Kit
USB Connection Cable
K1HA05CD0001
CD-ROM
5
Video Cable
VJA1153
6
Strap
VFC3801
KC4-PP.book 7 ページ 2002年1月21日 月曜日 午後7時51分
8
Names of the Components
[Front View]
1
REC/Power Switch
2
Self-timer Indicator (P33)
3
Flash Sensor (P32)
4
Flash
5
Lens
6
Lens Cover
7
Shutter Button (P23)
8
Playback/Power Switch (
P18, P44)
[Back View]
9
Flash Indicator (P22)
10
Status Indicator (P17, P22)
11
Optical Finder
12
LCD Monitor (P10)
13
MENU Button (P24)
14
Delete Button (P50)
15
Cursor (
3/4/2/1
)
Buttons
16
DISPLAY Button (P21)
17
Zoom Button (P29, P46)
1
7
8
2
3
4
5
6
9
10
11
12
1314
15
16
17
KC4-PP.book 8 ページ 2002年1月21日 月曜日 午後7時51分
9
[Left View]
18
Strap Eyelet (P19)
19
Video.OUT Socket (P64)
20
USB Socket (5pin) (P66)
A: SERIAL Socket (For Service
only)
[Right View]
21
Memory Card/Battery Door
(P13, P16)
22
Lock Lever
23
DC IN Socket (P14)
[Bottom View]
24
Tripod Receptacle (P20)
V. OUT
USB
A
18
19
20
LOCK
MEMORY CARD / BATT.
DC IN
22
23
21
24
KC4-PP.book 9 ページ 2002年1月21日 月曜日 午後7時51分
10
LCD Monitor Display
[In recording]
1
Battery indicator (P14)
(When using AC adaptor, this is
not displayed)
2
Focus mode (P42)
3
Flash mode (P31)
4
Self-timer mode (P33)
5
Exposure compensation (P36)
6
Camera jiggle alert (P22)
7
Digital zoom (P30)
8
ISO sensitivity (P41)
9
Frame remain
10
Spot mode (P38)
11
Spot area indication
12
White balance mode (P39)
13
Current date (P25)
14
Picture size (P34)
15
Quality (data compression ratio)
(P35)
16
Memory card indication (P16)
17
Motion image/Burst mode (P28,
P43)
1.25
11MAR.1.2002
1600
KC4-PP.book 10 ページ 2002年1月21日 月曜日 午後7時51分
11
[In playback]
18
DPOF setting indication (P52)
19
Picture size (P34)
20
Protected image (P55)
21
Quality (compression ratio) (P35)
22
White balance mode (P39)
23
Folder/File number
When the number of pictures is
more than 1000, the number
999 is displayed.
24
Recorded date
25
Shutter speed indication
26
F number indication
27
Motion image playback mode
(P49)
102-0048
1/125    MAR.1.2002
1600
F2.8
KC4-PP.book 11 ページ 2002年1月21日 月曜日 午後7時51分
12
Quick Guide
Prepare following items.
Camera
Battery
Memory card
AC adaptor
Check that the power switch is set to
[OFF].
1
Insert the battery into the camera.
(P13)
2
Connect the AC adaptor to the
camera, in order to charge the
battery. (P14)
3
Insert the memory card into the
camera. (P16)
A: Connection terminal on the back
side of the card.
4
Set the REC/power switch to [ON].
(P18)
5
Set the date. (P25)
6
Press the shutter button halfway to
set the focus. (P23)
7
Press the shutter button fully to take a
picture. (P23)
[Playback]
8
Set the playback[ ]/power switch
to [ON]. (P44)
9
Press
2/1
to play back a picture
you want to view.
1
2
3
A
4
8
6,7
9
KC4-PP.book 12 ページ 2002年1月21日 月曜日 午後7時51分
13
Inserting the Battery
[Preparation]
Set the power switch to [OFF].
1
Slide the lock lever.
2
Open the battery door and the inside
door.
3
Insert the battery while pressing the
inside door.
Insert the battery with the arrow part
upward and terminal part downward.
4
Close the battery door.
5
Lock lever on battery door.
When the camera will not be used for a
long time, remove the battery.
(When inserting the battery again, set the
date again)
Before removing the battery from the
camera, turn the camera off.
The supplied battery is for exclusive use
with this camera. Do not use it except
with this camera.
When turning the camera on, do not put
in/out the DC input lead, the data stored
in the card could be destroyed. And the
file number is not memorized, so the
picture with same file number is recorded
in the another card.
CAUTION
Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent
type recommended by the manufacturer.
Dispose of used batteries according to the
manufacturers instructions.
3
2
1
4
KC4-PP.book 13 ページ 2002年1月21日 月曜日 午後7時51分
14
Charging the Battery
[Preparation]
Set the power
switch to
[OFF].
1
Insert the battery into the camera.
(P13)
2
Plug the AC adaptor into the
electrical outlet.
The green status indicator
1
blinks
and charging starts.
During charging the battery, do not
open the battery door.
THE SOCKET OUTLET SHALL BE
INSTALLED NEAR THE EQUIPMENT
AND SHALL BE EASILY ACCESSIBLE.
3
Insert the connection plug of the AC
adaptor into the DC IN socket of the
camera.
4
When the status indicator stops
blinking, charging is complete.
After charging is finished, remove the
AC adaptor from the electrical outlet
and then remove the connecting plug
from the DC IN socket.
ª Battery indicator
The remaining battery power is displayed on the LCD monitor. (This is
not displayed when using AC adaptor)
: The battery power is sufficient
: The remaining power is a little low
: The remaining power is low
: Replace or recharge the battery
The status indicator also flashes. In this time, when pressing the shutter button
halfway, alarm sound rings.
2
3
KC4-PP.book 14 ページ 2002年1月21日 月曜日 午後7時51分
15
ª Charging time and available recording time
(when the supplied 8 MB SD Memory card is used)
A
Charging time
B
Continuous recording time (recordable number) (If the LCD monitor is ON)
C
Continuous recording time (recordable number) (If the LCD monitor is OFF)
ª Charging environment and charging error
Charge the battery in a place with the temperature of 10 to 35 °C. (The battery is
also the same temperature)
When charging starts, the status indicator blinks at about 2 second intervals. If,
after charging starts, the status indicator blinks quicker, its a charging error.
In this case, remove the AC adaptor from the electrical outlet, remove the battery
and check if both room and battery temperature is too low or high and then
charge it again. (It is not possible to cancel the error by only turning the camera
off/on) If the problem persists, consult the dealer.
ª Charging the built-in battery for dating
The date/time setting can be memorized using the built-in battery. Charge it
using the AC adaptor for 3 hours approximately. (When inserting the battery,
even if the status indicator finishes blinking, keep charging the built-in battery)
After the charging, set the date/time. (P25)
During the charging, do not open the battery door.
Connecting to an Electrical Outlet
If you use an AC adaptor and connect it to an electrical outlet, you can use the
camera without worrying about the battery discharge. The connection method
is the same as explained in [Charging the Battery]. (P14)
During use, the camera becomes warm, but it is not a malfunction.
KC4-PP.book 15 ページ 2002年1月21日 月曜日 午後7時51分
16
Inserting the Card
[Preparation]
Set the power switch to [OFF].
1
Slide the lock lever.
2
Open the memory card door.
3
Insert the card all the way in until it
clicks.
Check the direction of the card.
4
Close the memory card door.
5
Put the lock lever back.
[Removing the card]
1
Press the card.
2
Pull the card out.
Do not touch the connection terminal
1
on the back side of the card.
If the memory card door could not
completely closed, after taking out the
card, insert it again.
If the card is not inserted, verify whether
the direction of the card is correct.
We recommend you to use the card
manufactured by this company. (Use only
the genuine card)
Before removing the card from the
camera, turn the camera off.
1
2,3
4,5
KC4-PP.book 16 ページ 2002年1月21日 月曜日 午後7時51分
17
ª Access to the card
When you access to the card, the
green status indicator
1
lights.
When the status indicator lights, do
not remove the battery. Besides, do
not open the memory card door and
do not pull the card out. The card and
the card contents could be destroyed
and the camera could not operate
normally.
As the card contents could be
damaged or erased because of the
electrical noise, static electricity and
camera and card defects, store the
important data also in PC (P66) using
the USB socket.
ª SD Memory card (supplied) and
MultiMediaCard (optional)
The SD Memory card and
MultiMediaCard are small,
lightweight, removable external
cards. The SD Memory card is
equipped with a writing protection
switch that can inhibit writing and
formatting. (When the switch is
moved towards the [LOCK] side, it is
not possible to write or delete data on
the card and format it, but after
resetting, these functions become
available)
SD Memory card
RP-SDH512(512MB)
RP-SDH256(256MB)
RP-SDH128(128MB)
RP-SD064B (64MB)
RP-SD032B (32MB)
RP-SD016B (16MB)
RP-SD008B (8MB)
MultiMediaCard
VW-MMC16 (16MB)
VW-MMC8 (8MB)
When using the MultiMediaCard,
after recording motion images, the
screen may appear grey, but this is
not a malfunction.
KC4-PP.book 17 ページ 2002年1月21日 月曜日 午後7時51分
18
Turning Power on/off
[In recording]
[Turning the power on]
1
Slide the REC/power switch to open
the lens cover.
2
Furthermore, after sliding the switch
and turning on, set the REC mode.
The status indicator wil light.
[Turning the power off]
3
Slide back the REC/power switch and
turn the power off.
4
Furtermore, after sliding back the
switch, close the lens cover again.
Check that the lens is stored in
completely and then close the lens
cover.
[In playback]
1
Slide the playback[ ]/power switch.
The playback icon will be displayed.
2
Slide back the playback[ ]/power
switch, to turn the power off.
When the REC mode is set, if you slide the playback
[]/
power
switch
, the
setting will change to playback mode.
When switching the power on/off, do not put in front of the lens any obstacle.
1,2,3,4
1,2
KC4-PP.book 18 ページ 2002年1月21日 月曜日 午後7時51分
19
Attaching the Strap
1
Let the top of the strap pass through
the strap eyelet.
2
Let the opposite side of the strap
pass through its ring shaped part.
3
Pull the strap.
KC4-PP.book 19 ページ 2002年1月21日 月曜日 午後7時51分
20
Using the Tripod
When using the tripod (optional), you can
take pictures also with low shutter speed
and zoom.
1
Match with the tripod receptacle
1
of the camera.
2
Fix the tripod receptacle.
Read carefully the tripod operating
instructions.
1
2
W
T
KC4-PP.book 20 ページ 2002年1月21日 月曜日 午後7時51分
21
Using the LCD Monitor
Every time you press the [DISPLAY]
button, the display of the LCD monitor
changes as shown below.
[In recording]
[In playback]
Only in REC mode settings are kept, even if you turn the power off.
When setting the digital zoom to [ON], the display of the LCD monitor is not set to
off.
When setting the auto review to [ON], it is available, even if the display of the LCD
monitor is set to off. (After finishing the auto review, the display is returned to off)
After recording, if you press the [REVIEW/SET] button, the review is displayed,
even if the LCD monitor is set to off. (After finishing the review, the display is
returned to off)
DISPLAY
MAR.1.2002
AF
AUTO
±0.00
11
AF
±0.00
11
MAR.1.2002
AUTO
KC4-PP.book 21 ページ 2002年1月21日 月曜日 午後7時51分
22
The Indicators
ª Status Indicator (Green) 1
[Blinking]
Warning indication
During recording the motion image
[Lighting]
When turning the power switch to [ON]
When accessing to the card
ª Flash Indicator (Red) 2
[Blinking]
When charging the flash (Blinking fast)
When setting the flash mode to forced off
and recording in dark places (Blinking
slowly)
[ ] is displayed on the LCD monitor.
[Lighting]
When the flash firing (It lights when the
shutter is pressed halfway)
KC4-PP.book 22 ページ 2002年1月21日 月曜日 午後7時51分
23
The Shutter Button
(Pressing halfway/Pressing fully)
The shutter button is pressed in 2 steps:
[pressing halfway] and [pressing fully].
Pressing halfway (Press lightly)
A
Focus and exposure are locked.
Pressing fully (Press all the way)
B
The picture is captured in the card. In
motion image mode, the recording starts.
You can set the beep sound in menu.
(P60)
When pressing the shutter button fully at
a stroke, the camera is shaken or the
focus is not adjusted.
KC4-PP.book 23 ページ 2002年1月21日 月曜日 午後7時51分
24
Operating the Menu
By operating the menu it is possible to set
the settings of the REC or playback mode.
Besides, it is possible to set the date and
time, the beep sound, and any sort of
settings. Follow these instructions looking
at the LCD monitor.
1
Press the [MENU] button.
If you set to the REC mode, the REC
menu is displayed; if you set to the
playback mode [ ], the playback
menu is displayed.
2
Press
3/4
to choose the item and
press
2/1
to confirm this setting.
First, with step 2, if you press
3
and
then press
1
, you will access to the
setup menu. (Pressing the menu
button you will return back)
3
Press the [MENU] button.
The menu will disappear.
1,3
2
EXPOSURE
BURST
D.ZOOM
MOTION IMAGE
±0.00
1 / 3
W.BALANCE
W.BALANCE
EXPOSURE
BURST
MOTION IMAGE
±0.00
1 / 3
D.ZOOM
W.BALANCE
EXPOSURE
BURST
MOTION IMAGE
±0.00
1 / 3
D.ZOOM
KC4-PP.book 24 ページ 2002年1月21日 月曜日 午後7時51分
25
Setting the Date/Time (Clock Set)
It is possible to set the year from 2000 to
2049. The 24-hour system is used.
[Preparations]
Charge the built-in battery for dating.
(P14)
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3(or 4
)
to choose the
[SETUP] and press
1
to open the
setup menu.
3
Press
3(or 4
)
to
select [CLOCK
SET].
4
Press
3/4/2/1
to
set date and
time.
5
Press the [MENU] button.
The menu will disappear.
Even if the battery is not inserted or the
AC adaptor is not connected, the
camera, with a built-in power source for
back-up, can store the set time for about
10 minutes (with about 3 hour charge).
But, after this limit, the set time is
cancelled, so set date and time again.
1,5
2,3,4
CLOCK SET
YEAR
MONTH
DAY
TIME
STYLE
2002
MAR
1
19:04
MDY
2 / 2
3,4
KC4-PP.book 25 ページ 2002年1月21日 月曜日 午後7時51分
26
Taking Pictures
Only pressing the shutter button, the
exposure (shutter speed and aperture
value) will be automatically adjusted and
the picture is taken.
[Preparations]
Insert the card. (P16)
Set the REC/power switch to [ON]. (P18)
1
Let the subject be centered in the AF
target
1
inside the optical finder
A
and press the shutter button halfway.
You can take pictures using the LCD
monitor
B
.
Adjust the focus.
2
Press the shutter button fully to take
the picture.
After taking a picture, when the auto
review (P59) is set to [ON], the
picture is displayed on the LCD
monitor for about 2 seconds.
When power saving is set, if you do not operate the camera, it is automatically
turned off. To operate the camera again, set the REC/power switch first to [OFF]
and then to [ON], or press the shutter button halfway. (P61)
1,2
2
AUTO
11
AF
±0.00
KC4-PP.book 26 ページ 2002年1月21日 月曜日 午後7時51分
27
Checking the Last Picture (Review)
After taking a picture, when auto review
(P59) is set to [ON], the captured picture is
displayed on the LCD monitor for about 2
seconds, but you can also check the
picture following the methods shown
below.
1
After taking a picture, press the
[REVIEW/SET] button.
The last captured picture is
displayed. Pressing
2/1
, it is
possible to select the picture to
display. Pressing the zoom button
(T), the captured picture is zoomed
2.5 times (
A)
and 4 times if you
press once again. Pressing the zoom
button (W), you will reduce it.
ªErasing the captured picture during
the review
2
Press the [ ] button.
3
Press
2/1
to select [YES].
4
Press the [ ] button or the
[REVIEW/SET] button.
The picture is erased.
Once erased pictures cannot be
recovered.
In motion image mode [ ], the index
picture is reviewed.
2,4
1
3
1
EXIT
REVIEW
REVIEW
KC4-PP.book 27 ページ 2002年1月21日 月曜日 午後7時51分
28
Recording Motion Images
[Preparations]
Insert the card. (P16)
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3/4
to select [MOTION
IMAGE].
3
Press
2/1
to select [ON].
4
Center the subject on the LCD
monitor and press the shutter button
halfway.
Adjust the focus.
5
Pressing the shutter button fully, the
recording starts.
During recording, the status indicator
blinks.
Audio is not recorded.
Picture size is set at 320
×
240 pixels.
6
Pressing the shutter button fully
again, recording stops.
If during the recording the memory of
the card becomes full, the recording
is stopped automatically.
ªAvailable settings in motion image mode
Macro mode (P42)
Unlimited recording
Spot recording
The remaining time displayed on the LCD monitor is the approximation.
It is possible to record motion images maximum of 20 seconds.
After recording motion images, the status indicator blinks while the images are
recorded to the memory card, and after recording completion it lights. Do not
operate during the recording.
When setting [MOTION IMAGE] to [ON], you cannot select [BURST],
[PICT.SIZE], [QUALITY] and [D.ZOOM].
If using the MultiMediaCard, after recording motion images, the screen may
appear grey, but this is not a malfunction.
When recording is started, the auto focus and zoom are locked (with the first
frame).
2,3
1
4,5
KC4-PP.book 28 ページ 2002年1月21日 月曜日 午後7時51分
29
Using the Optical Zoom
With this function, you can make people
and subjects closer and landscapes can
be captured in wide angle, because they
can be further zoomed by 2 times.
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Aim the camera at the subject and
adjust the size with the zoom button.
To make subjects closer (Tele):
Press the zoom button (T).
To make subjects wider (Wide angle):
Press the zoom button (W).
2
Take pictures.
The recording method is the same as
in [Taking Pictures]. (P26)
The focus is adjusted at a distance of
more than 10 cm. As regards Macro
mode, read P42.
W T
KC4-PP.book 29 ページ 2002年1月21日 月曜日 午後7時51分
30
Using the Digital Zoom
Using the digital zoom, it is possible to
magnify a subject to 2 times if the picture
size is 800
×
600, and 2.5 times if the
picture size is 600
×
480.
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3/4
to select [D. ZOOM].
3
Press
2/1
to set to [ON].
4
Press the [MENU] button.
The menu will disappear.
The zoom adjustment and recording
method are the same as in [Using the
Optical Zoom]. (P29)
If the picture size is 1600
×
1200, it is not
possible to change the zoom
magnification ratio.
In motion image mode [ ], you cannot
use the digital zoom.
When setting the [D. ZOOM] to [ON], if
setting [MOTION IMAGE] to [ON], digital
zoom menu remains [ON]. However, it
does not work. When setting [MOTION
IMAGE] to [OFF], digital zoom returns to
selected operation.
The digital zoom is available only when
the LCD monitor is set to on.
Using the digital zoom, the picture quality
becomes deteriorated.
1,4
2,3
W.BALANCE
EXPOSURE
BURST
MOTION IMAGE
±
0.00
1 / 3
D.ZOOM
KC4-PP.book 30 ページ 2002年1月21日 月曜日 午後7時51分
31
Taking Pictures with the Built-in Flash
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press [ ].
Every time you press it, the available
settings will appear as shown below.
: AUTO
The flash fires automatically according
to the recording situation.
: Forced ON
The flash is forced to fire.
You will use it when a subject is
backlighted.
: AUTO/Red-eye reduction
The flash fires automatically according
to the recording situation and
simultaneously it reduces the red-eye
phenomenon (when a subjects eyes
appear red in flash light).
Use it when a subject is recorded in dark
places.
: Slow synchro
When you take a picture with a dark
background landscape, it makes the
flash fire and the shutter speed be slow,
so that the dark background landscape
will become bright.
: Forced OFF
Even being in dark places, the flash
does not light.
Set it when you take pictures in places
where flash is forbidden.
1
KC4-PP.book 31 ページ 2002年1月21日 月曜日 午後7時51分
32
2
Take a picture.
The recording method is the same as in
[Taking Pictures]. (P26)
The available flash range is about 10 cm to 4.5 m at a maximum wide angle and
about 20 cm to 3.5 m at a maximum telephoto setting.
Do not cover the flash sensor
1
with your fingers or other items. Otherwise,
brightness cannot be perceived.
In motion image [ ] or burst [ ] mode, the flash mode is set to Forced OFF
[].
During flash charging it is possible to press the shutter button.
When the remaining power becomes low, the flash mode set to Forced OFF [ ]
and the flash indicator blinks.
KC4-PP.book 32 ページ 2002年1月21日 月曜日 午後7時51分
33
Taking Pictures with the Self-timer
When you set the self-timer, the picture is
automatically taken after 10 seconds (or 2
seconds).
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [ ] button.
Every time you press it, what is
displayed changes as shown below.
: Self-timer set to 10 seconds
: Self-timer set to 2 seconds
When these indicators are not
displayed, self-timer setting is
cancelled.
2
Press the shutter button fully.
The self-timer indicator blinks and the
shutter is activated after 10 seconds
(or 2 seconds).
Before taking a picture, if you press
the
shutter button fully again
, the
self-timer setting is cancelled.
In motion image mode [ ], the self-timer is not available.
In burst mode [ ], the self-timer setting covers only the first picture.
1
2
10 s 2 s
OFF
KC4-PP.book 33 ページ 2002年1月21日 月曜日 午後7時51分
34
Changing the Picture Size
You can choose among 3 kinds of picture
size settings.
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3/4 to select [PICT. SIZE].
3
Press
2/1
to set the picture size.
: 1600 x 1200 pixels
: 800 x 600 pixels
: 640 x 480 pixels
4
Press the [MENU] button.
The menu will disappear.
In motion image mode [ ], it is fixed to 320 x 240 pixels.
If you set the pictures size to small, the memory card can record more pictures.
Moreover, as the data volume is small, you can easily attach the picture to an
e-mail or use it in a web site.
If you set the picture size to large, it is possible to print clearer sheets.
1,4
2,3
PICT.SIZE
QUALITY
SENSITIVITY
SPOT MODE
MONITOR
2 / 3
1600
800 640
100
ISO
2,3
KC4-PP.book 34 ページ 2002年1月21日 月曜日 午後7時51分
35
Changing the Quality
(Data Compression Ratio)
You can choose among 2 kinds of quality
levels (Data Compression Ratio).
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3/4 to select
[QUALITY].
3
Press
2/1
to select the quality (Data
Compression Ratio).
: Fine (Low compression)
It gives priority to picture quality and
record high quality pictures.
: Standard
(Standard compression)
It gives priority to the number of
recordable pictures and record
standard quality pictures.
A: Quality and number of
recordable
pictures
(a Picture size, b Quality) (With
the supplied 8MB SD memory card)
4
Press the [MENU] button.
The menu will disappear.
In motion image mode [ ], quality cannot be modified.
It could happen that picture are like a mosaic depending on the scene
characteristics.
The number of recordable pictures corresponds to the capacity of the supplied
8MB SD Memory card. (If you mix fine quality and standard quality, the number of
recordable pictures changes)
Remaining frame which is displayed on the LCD monitor may not correspond with
recorded frames. However, this is not a malfunction.
1,4
2,3
QUALITY
PICT.SIZE
SENSITIVITY
SPOT MODE
MONITOR
2 / 3
100
640
ISO
2,3
KC4-PP.book 35 ページ 2002年1月21日 月曜日 午後7時51分
36
Compensating the Exposure
If there is a difference between the subject
and background brightness, since you
cannot set the correct exposure, you can
compensate it.
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3/4
to select [EXPOSURE].
3
Press
2/1
to set the exposure
compensation.
You can compensate from -2.00 to
+2.00 with 0.25 step.
(Exposure value is the amount of light
given to the CCD by the aperture
value and the shutter speed.
±
0.00: the exposure capacity with the
aperture value F1.0 and the shutter
speed 1 second
When the aperture value or shutter
speed rises, EV1, EV2, EV3... rise
too.)
The compensation state is not
reflected on the LCD monitor.
4
Press the [MENU] button.
The menu will disappear.
5
Take a picture.
The recording method is the same as
in [Taking Pictures]. (P26)
1,4
2,3
5
EXPOSURE
W.BALANCE
BURST
D.ZOOM
MOTION IMAGE
-0.25
±0.00
  
+0.25
1 / 3
AUTO
2
KC4-PP.book 36 ページ 2002年1月21日 月曜日 午後7時51分
37
Using the AF/AE Lock
If the subject is out of the AF target and
you press the shutter button, the subjects
focus is not adjusted. After locking focus
and exposure (AF/AE lock), you can take a
clear picture with adjusted focus.
AF: Auto focus
AE: Auto exposure
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Centre the subject in the AF target
1
inside the optical finder and keep the
shutter button pressed halfway (AF/
AE lock) to set it.
2
Move the camera keeping the chosen
composition and press the shutter
button all the way.
Before pressing the shutter button, you
can set the AF/AE lock any time you
want.
1,2
1
2
KC4-PP.book 37 ページ 2002年1月21日 月曜日 午後7時51分
38
Using the Spot AF
Set the metering mode using the spot area
that is displayed on the LCD monitor.
When [SPOT MODE] is set to [OFF],
evaluation metering is set.
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3/4
to select [SPOT MODE].
3
Press
2/1
to set to [ON].
4
Press the [MENU] button.
The menu will disappear.
5
Centre the subject in the spot area
1
.
6
Take a picture.
The recording method is the same as
in [Taking Pictures]. (P26)
When taking pictures with spot AF mode, it is recommended to use the LCD
monitor.
1,4
2,3
6
SPOT MODE
PICT.SIZE
QUALITY
SENSITIVITY
MONITOR
2 / 3
100
ISO
640
2,3
5
KC4-PP.book 38 ページ 2002年1月21日 月曜日 午後7時51分
39
Setting the White Balance
With the auto white balance you can
automatically adjust the natural color tone,
but in some particular situations,
depending on light and environment
conditions, you cannot do it and you have
to adjust the white balance manually.
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3/4
to
select [W.BALANCE].
3
Press
2/1
to
select the mode.
AUTO: if the auto white balance is set
(Daylight): for recording outdoors
on a bright day
(Cloudy): for recording under
cloudy and shady sky
(Halogen): for recording under
halogen lamp
(Night scene): for taking a picture
in a night scene
(White set): for manual setting
(Read the following page where the
manual setting is explained in detail)
4
Press the [MENU] button.
The menu will disappear.
5
Take a picture.
The recording method is the same as
in [Taking Pictures]. (P26)
When setting the white balance mode to Night scene [ ], the flash mode is
automatically set to Slow synchro. And it is possible to set the flash mode to only
Forced OFF or Slow synchro.
5
1,4
2,3
W.BALANCE
EXPOSURE
BURST
D.ZOOM
MOTION IMAGE
±0.00
1 / 3
2,3
KC4-PP.book 39 ページ 2002年1月21日 月曜日 午後7時51分
40
Here the white set mode of white balance
is explained.
1
Press the [MENU] button.
2
Press
3/4
to
select [W.BALANCE].
3
Press
2/1
to
set to white set [ ].
4
Press the [MENU] button.
The menu will disappear.
Only when setting the white balance again
5
Aim the camera at a white paper
A
or similar objects so that it completely
fills the frame to white on the screen
and press
1
until the [ ] indicator
is displayed.
White balance is set.
5
1
4
2,3
W.BALANCE
EXPOSURE
BURST
D.ZOOM
MOTION IMAGE
±0.00
1 / 3
2,3
KC4-PP.book 40 ページ 2002年1月21日 月曜日 午後7時51分
41
Setting ISO Sensitivity
ISO sensitivity is a value that corresponds
to the sensitivity to light. The higher it is,
the better the camera performances are in
dark places.
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3/4
to
select [SENSITIVITY].
3
Press
2/1
to
select the sensitivity.
:ISO100
:ISO200
:ISO400
4
Press the [MENU] button.
The menu will disappear.
5
Take a picture.
The recording method is the same as
in [Taking Pictures]. (P26)
1,4
2,3
5
SENSITIVITY
PICT.SIZE
QUALITY
SPOT MODE
MONITOR
2 / 3
100 200
400
640
ISO
2,3
KC4-PP.book 41 ページ 2002年1月21日 月曜日 午後7時51分
42
Taking Pictures with Macro Mode/
Unlimited Recording
If the camera lens is at a distance from 10
cm to 100 cm from the subject or unlimited
distance, set macro mode [ ] or unlimited
recording [ ].
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [ ] button.
Every time you press it, what is
displayed changes as shown below.
[ ] Macro mode
[ ] Unlimited recording mode
[ ] Auto focus
2
Take a picture.
The recording method is the same as
in [Taking Pictures]. (P26)
In motion image mode [ ], it is also possible to set macro mode or unlimited
recording mode.
1
2
AF
KC4-PP.book 42 ページ 2002年1月21日 月曜日 午後7時51分
43
Taking Pictures with Burst Mode
Pressing continuously the shutter button, it
is possible to record in burst mode. (4
frames/second maximum of 5 frames)
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button [ ].
2
Press
3/4
to
select [BURST].
3
Press
2/1
to
set to [ON].
4
Press the [MENU] button.
The menu will disappear.
5
Press the shutter button halfway to
lock the focus, and then press it fully
to take pictures in sequence.
The flash mode is set to Forced OFF
[].
In motion image mode [ ], the burst
mode cannot be used.
Only the first picture recorded is
displayed on the LCD monitor.
Since the picture size in the burst mode
is smaller than the single picture mode,
the picture quality may be deteriorated.
1,4
2,3
5
KC4-PP.book 43 ページ 2002年1月21日 月曜日 午後7時51分
44
Playing Back Still Pictures
1
Slide the playback [ ]/power
switch.
The last recorded picture is played
back.
2
Press
2
to
play back
the previous
picture.
Press
1
to
play back
the following
picture.
Every time you press, the previous
(following) picture is played back.
The picture following to the last one is
the first picture.
This camera is based on the DCF standards (Design rule for Camera File system)
which were established by the Japan Electronic Industry Technology Association
(JEITA).
The file format that can be played back with this camera is JPEG. (There are also
pictures that cannot be played back in JPEG format)
When playing back still pictures that have been recorded with other equipments,
the quality of images may be deteriorated and images could not be played back.
1
2
KC4-PP.book 44 ページ 2002年1月21日 月曜日 午後7時51分
45
9 Images Multi Playback
It is possible to display 9 images at once.
[Preparation]
Set the playback [ ]/power switch to
[ON].
1
During playback, press the zoom (W)
button [ ].
Multi playback (9 frames) starts.
2
Press
3
/
4
/
2
/
1
to select images.
To return the normal indication, press
the zoom (T) button [ ]. The
selected image displays.
1
2
KC4-PP.book 45 ページ 2002年1月21日 月曜日 午後7時51分
46
Using the Playback Zoom
During playback it is possible to enlarge
pictures.
[Preparation]
Set the playback [ ]/power switch to
[ON].
1
During playback, press the zoom (T)
button [ ].
To enlarge further more
, press the
zoom (T) button [ ] again.
To reduce the picture
, press the
zoom (W) button [ ].
Use
3/4/2/1
to change the area
to be enlarged.
In motion image playback, it is not possible to magnify.
The more the zoom magnification increases, the more the picture quality
deteriorates.
The playback zoom could not operate if pictures have been recorded with other
equipments.
W T
KC4-PP.book 46 ページ 2002年1月21日 月曜日 午後7時51分
47
Editing the Recorded Pictures
It is possible to add special effects to the
recorded pictures such as black and white,
sepia and nega effect, and to insert the
date into the pictures.
[Preparation]
Set the playback [ ]/ power switch to
[ON].
1
Press the [MENU] button.
2
Press
3
/
4
to select [EDIT] and then
press
1
.
3
Press
2/1
to select the picture and
then press
4
.
4
Press
2/1
to select among [B/W],
[SEPIA], [NEGA] and [DATE], and
then press
4
.
[B/W]: the colored picture is changed into
a black and white picture.
[SEPIA]: the sepia color produces the
effect of old black and white pictures.
[NEGA]: the effect of negative or positive
film is produced.
[DATE]: date is added.(See the next
page)
5
Press
3/4
to select [SAVE AS] or
[SAVE], and then press
1
.
When the remaining capacity of the
memory card is small, it is not
possible to select [SAVE AS].
6
Press the [MENU] button twice.
The menu will disappear.
In motion image[ ] playback, it is not possible to edit.
1,6
2,3,4,5
EDIT
PROTECT
DPOF
SLIDE SHOW
EDIT
2
EDIT
B/W SEPIA
4
KC4-PP.book 47 ページ 2002年1月21日 月曜日 午後7時51分
48
Adding the Date
It is possible to provide the played back
pictures with date.
[Preparation]
Set the playback [ ]/power switch to
[ON].
1
Press the [MENU] button.
2
Press
3/4
to select [EDIT] and then
press
1
.
3
Press
2/1
to select the picture and
then press
4
.
4
Press
2/1
to select [DATE] and
then press
4
.
5
Press
2/1
to select the picture
direction and then press
4
.
Each time you press
2/1
, the direction
will change.
6
Press
3/4
to select [SAVE AS] or
[SAVE], and then press
1
.
7
Press the [MENU] button twice.
The menu will disappear.
In motion image[ ] playback, it is not possible to add the date.
When the remaining capacity of the memory card is small, it is not possible to
select [SAVE AS].
1,7
2,3,4,5,6
EDIT
NEGA DATE
4
KC4-PP.book 48 ページ 2002年1月21日 月曜日 午後7時51分
49
Playing Back Motion Images
[Preparation]
Set the playback [ ]/power switch to
[ON].
1
Press
2/1
to select the file with the
motion image icon [ ]
1
.
2
Press
4
to playback the motion
image.
Pressing
4
, motion image playback
will stop.
When selecting other files, press
2/1.
The file format that can be played back with this camera is QuickTime Motion
JPEG.
When playing back motion images that have been recorded with other
equipment, some QuickTime Motion JPEG files cannot be played back.
1,2
PLAY/STOP:
KC4-PP.book 49 ページ 2002年1月21日 月曜日 午後7時51分
50
Deleting Images
Images recorded on the card can be
deleted.
Once deleted images cannot be
recovered.
[Preparations]
Set the playback [ ]/power switch to
[ON].
When an image is protected, it cannot be
deleted. Cancel the protect setting. (P55)
[Delete single image]
1
Press the [ ] button.
2
Press
3/4
to
select [SELECT] and
press
1
.
3
Press
2/1
to select the image to be
deleted and press the [REVIEW/SET]
button.
4
Press
2/1
to select [DELETE] and
press the [REVIEW/SET] button.
The selected image is deleted.
5
Press the [MENU] button three times.
The deleting menu will disappear.
5
1
2,3,4
DELETE
SELECT
ALL
FORMAT
SELECT
DELETE
  
CANCEL
1 0 2 - 0 0 4 7
2
4
KC4-PP.book 50 ページ 2002年1月21日 月曜日 午後7時51分
51
Deleting Images (Continued)
[Delete all images]
Once deleted images cannot be
recovered.
1
Press the [ ] button.
2
Press
3/4
to select [ALL] and press
1
.
3
Press
2/1
to select [DELETE] and
press the [REVIEW/SET] button.
All images are deleted.
During deleting, do not take out the memory card or do not turn the power off.
When displaying 9 images, delete the images by
pressing
the [ ] button after
selecting a images with
2/1
and the [REVIEW/SET] button.
1
3
2
KC4-PP.book 51 ページ 2002年1月21日 月曜日 午後7時51分
52
Writing the Print Information in the Card
(DPOF Setting)
It is possible to write on the card
information (DPOF data) about the images
that you want to print and the number of
sheets.
DPOF is an abbreviation of Digital Print
Order Format. To use the DPOF
corresponding system, you can add print
information to the images on the memory
card.
[Preparation]
Set the playback [ ]/power switch to
[ON].
[
Single
copy setting
]
1
Press the [MENU] button.
2
Press
3/4
to select [DPOF] and
then press
1
.
3
Press
3/4
to select [SELECT] and
then press
1
.
4
Press
2/1
to select 1 image.
5
Press
3/4
to
set the number of
sheets to be printed.
The number of sheets can be set
from 1 to 15.
6
Press the [MENU] button.
The DPOF setting is written on the
card.
7
Press the [MENU] button twice.
The menu will disappear.
DPOF
PROTECT
DPOF
SLIDE SHOW
EDIT
DPOF
SELECT
ALL
INDEX
RESET
SELECT
SHEETS: 5
SHEETSTOTAL  102
       EXIT
2
3
4,5
KC4-PP.book 52 ページ 2002年1月21日 月曜日 午後7時51分
53
[
All
copy setting
]
1
Press the [MENU] button.
2
Press
3/4
to select [DPOF] and
then press
1
.
3
Press
3/4
to select [ALL] and then
press
1
.
When DPOF data have been written,
cancel all DPOF settings.
4
Press
3/4
to
set the number of
sheets to be printed and then press
1
.
The number of sheets can be set
from 1 to 15.
5
Press the [MENU] button.
The DPOF setting is written on the
card.
6
Press the [MENU] button twice.
The menu will disappear.
When setting DPOF by this camera for
images that have been set to slide show
by other equipments, the slide show
settings are overwritten by DPOF slide
show (P56).
KC4-PP.book 53 ページ 2002年1月21日 月曜日 午後7時51分
54
Writing the Print Information in the Card
(DPOF Setting) (Continued)
[
To cancel
all settings]
1
Press the [MENU] button.
2
Press
3/4
to select [DPOF] and
then press
1
.
3
Press
3/4
to
select [RESET] and
then press
1
.
4
Select [RESET].
5
Press the [MENU] button.
All DPOF settings are cancelled.
6
Press the [MENU] button three times.
The menu will disappear.
[
Index setting
]
1
Press the [MENU] button.
2
Press
3/4
to
select [DPOF] and
then press
1
.
3
Press
3/4
to
select [INDEX] and
then press
1
.
4
Press
3/4
to
set the number of
sheets to be printed.
5
Press the [MENU] button.
All images are set.
6
Press the [MENU] button twice.
The menu will disappear.
1,5,6
2,3,4
DPOF
PROTECT
DPOF
SLIDE SHOW
EDIT
DPOF
SELECT
ALL
INDEX
RESET
DPOF
SELECT
ALL
INDEX
RESET
2
3
KC4-PP.book 54 ページ 2002年1月21日 月曜日 午後7時51分
55
Protecting Images on the Card
It is possible to protect the important
images recorded on the card from
accidental erasure.
[Preparation]
Set the playback [ ]/power switch to
[ON].
1
Press the [MENU] button.
2
Press
3/4
to
select [PROTECT]
and then press
1
.
3
Press
3/4
to
select [SELECT]/[ALL]
and then press
1
.
4
Only when setting [SELECT], press
2/1
to select 1 image.
5
Press the [REVIEW/SET] button.
6
Press the [MENU] button three times.
The menu will disappear.
Even if an image is protected, it will be erased in case of formatting.
When trying to delete a protected file, these messages are displayed
[PROTECTED] or [PROTECTED IMAGE LEFT]. But if you want to delete it,
cancel the protect setting.
The protect setting is effective only in this camera.
1,5,6
2,3,4
PROTECT
PROTECT
DPOF
SLIDE SHOW
EDIT
PROTECT
SELECT
ALL
2
3
KC4-PP.book 55 ページ 2002年1月21日 月曜日 午後7時51分
56
Playing Back with Slide Show
(Automatic Playback)
All pictures selected in the card can be
played back one-by-one automatically.
[Preparation]
Set the playback [ ]/power switch to
[ON].
1
Press the [MENU] button.
2
Press
3/4
to select [SLIDE SHOW]
and then press
1
.
3
Press
3/4
to
select [ALL]/[DPOF]
and then press
1
.
ALL: for playback of all pictures
DPOF: for playback of the DPOF set
pictures
4
Press
3/4
to
set [DURATION] and
press
1
.
DURATION: it can be set from 1 to 10
seconds.
5
Press
2/1
to
select [FWD.]/[REV.]
and press the [REVIEW/SET] button.
The slide show starts.
Pressing the [MENU] button, it stops.
Editing with the supplied software [SD
Viewer for DSC] on the
CD-ROM, you can playback in SD slide
show with this camera. Read P71.
1
2,3,4,5
SLIDE SHOW
PROTECT
DPOF
SLIDE SHOW
EDIT
SLIDE SHOW
ALL
DPOF
ALL
ALL
DURATION5 SEC
FWD. REV.
5
4
3
2
KC4-PP.book 56 ページ 2002年1月21日 月曜日 午後7時51分
57
Formatting the Card
Usually, it is not necessary to format the
card (initializing). Format the card when
this message is displayed
[
MEMORY
CARD ERROR
]
.
[Preparation]
Set the playback [ ]/power switch to
[ON].
1
Press the [ ] button.
2
Press
3/4
to
select [FORMAT] and
then press
1
.
3
Press
2/1
to select [FORMAT].
4
Press the [REVIEW/SET] button.
The card is formatted.
After formatting, recorded images
and any other data cannot be
recovered.
When the card is formatted by PC or other equipments, format the card on the
camera again.
During formatting, do not turn the power off. (Do not open the memory card/
battery door)
If the card cannot be formatted, consult the dealer.
1
2,3
4
DELETE
SELECT
ALL
FORMAT
FORMAT
FORMAT
  
CANCEL
2
3
KC4-PP.book 57 ページ 2002年1月21日 月曜日 午後7時51分
58
Adjusting the LCD Monitor Brightness
[Preparation]
Set the REC/power switch to [ON]. (P18)
1
Press the [MENU] button.
2
Press
3/4
to
select [MONITOR].
3
Press
2/1
to
adjust the brightness.
4
Press the [MENU] button.
The menu will disappear.
1,4
2,3
MONITOR
PICT.SIZE
QUALITY
SENSITIVITY
SPOT MODE
ISO
640
400
2 / 3
2,3
KC4-PP.book 58 ページ 2002年1月21日 月曜日 午後7時51分
59
Using the Auto Review
Recording with the auto review set to [ON],
the recorded picture is automatically
displayed on the LCD monitor for about 2
seconds.
[Preparation]
Set the REC/power switch to [ON].
1
Press the [MENU] button.
2
Press
3/4
to select [SETUP] and
then press
1
.
The setup menu will be displayed.
3
Press
3/4
to
select [AUTO
REVIEW].
4
Press
2/1
to
select [ON].
5
Press the [MENU] button twice.
The menu will disappear.
In burst mode [ ], only the first recorded picture is displayed.
Even if setting the auto review to [ON], it is not available in motion image mode
[].
1,5
2,3,4
AUTO REVIEW
BEEP
POWER SAVE
NO.RESET
MEMORY
1 / 2
3,4
KC4-PP.book 59 ページ 2002年1月21日 月曜日 午後7時51分
60
Setting up the Beep Sound
It is possible to set the electronic sound
when the menu is operated.
[Preparation]
Set the REC/power switch to [ON].
1
Press the [MENU] button.
2
Press
3/4
to select [SETUP] and
then press
1
.
The setup menu will be displayed.
3
Press
3/4
to
select [BEEP].
4
Press
2/1
to
select [ON].
5
Press the [MENU] button twice.
The menu will disappear.
1,5
2,3,4
BEEP
AUTO REVIEW
POWER SAVE
NO.RESET
MEMORY
1 / 2
3,4
KC4-PP.book 60 ページ 2002年1月21日 月曜日 午後7時51分
61
Setting up the Power Save Mode
When setting this mode, the camera, if it is
not operated for certain time, is
automatically turned off.
[Preparation]
Set the REC/power switch to [ON].
1
Press the [MENU] button.
2
Press
3/4
to select [SETUP] and
then press
1
.
The setup menu will be displayed.
3
Press
3/4
to
select [POWER
SAVE].
4
Press
2/1
to
select [ON].
When the camera is in REC mode
and it is not operated for about 2
minutes, the power save mode is set
and after still more about 8 minutes it
is automatically turned off. Moreover,
in playback mode, it is not operated
for about 10 minutes, it is
automatically turned off.
If selecting [OFF], the power is not
turned off automatically.
5
Press the [MENU] button twice.
The menu will disappear.
If you want to cancel the power save mode, press the shutter button halfway or
after setting the REC/power switch to [OFF] set it to [ON] again.
Do not forget turning the power off in the power save mode.
Using the AC adaptor, the power save mode is not available.
1,5
2,3,4
POWER SAVE
AUTO REVIEW
BEEP
NO.RESET
MEMORY
1 / 2
3,4
KC4-PP.book 61 ページ 2002年1月21日 月曜日 午後7時51分
62
Resetting the File Number
As the file numbers are recorded
sequentially by the camera side, when you
use some cards, it could happen that the
file numbers on your cards are not in order.
Use this function when you insert a new
card and you want to start recording from
the file number 0001.
[Preparation]
Set the REC/power switch to [ON].
1
Press the [MENU] button.
2
Press
3/4
to select [SETUP] and
then press
1
.
The setup menu will be displayed.
3
Press
3/4
to
select [NO.RESET].
4
Press
2/1
to
select [ON].
5
Press the [MENU] button twice.
The menu will disappear.
1,5
2,3,4
NO.RESET
AUTO REVIEW
BEEP
POWER SAVE
MEMORY
1 / 2
3,4
KC4-PP.book 62 ページ 2002年1月21日 月曜日 午後7時51分
63
Memorizing settings
If setting [
MEMORY
] to [ON], focus mode,
flash mode and exposure compensation
settings are memorized even after turning
the power off.
[Preparation]
Set the REC/power switch to [ON].
1
Press the [MENU] button.
2
Press
3/4
to select [SETUP] and
then press
1
.
The setup menu will be displayed.
3
Press
3/4
to
select [MEMORY].
4
Press
2/1
to
select [ON].
5
Press the [MENU] button twice.
The menu will disappear.
When setting to [ ] and keeping on pressing
1
it is possible to reset the
settings. (Only the clock setting cannot be reset)
Even if setting [MEMORY] to [OFF], the menu settings remain memorized. (The
exposure compensation setting is not memorized)
1,5
2,3,4
MEMORY
AUTO REVIEW
BEEP
POWER SAVE
NO.RESET
1 / 2
3,4
KC4-PP.book 63 ページ 2002年1月21日 月曜日 午後7時51分
64
Playing Back Images with TV Monitor
Connecting the camera to a TV via the
supplied video cable
1
, it is possible to
view and playback the recorded images.
[Preparation]
Turn the camera and the TV off.
1
Connect
the video cable to the
V.OUT socket of the camera.
2
Connect the video cable to the video
input sockets of the TV.
3
Turn the TV on and select external
input.
4
Set the playback [ ]/power switch
to [ON].
The image is displayed on the TV.
It is not possible to display images on a TV in REC mode.
Do not use any other cables except the supplied one.
Read the TV operating instructions too.
V. OUT
USB
KC4-PP.book 64 ページ 2002年1月21日 月曜日 午後7時51分
65
After Use
After using the camera and after following
steps, it is recommended to insert it in the
optional soft case, in order to preserve it.
1
Set the power switch to [OFF]. (P18)
2
Remove the card. (P16)
KC4-PP.book 65 ページ 2002年1月21日 月曜日 午後7時51分
66
Connecting to PC
[Preparation]
Only if using Windows, start the supplied
CD from PC and install the USB driver.
1
Connect the camera to PC via the
supplied USB cable.
2
After inserting the memory card into
the camera, set the playback [ ]/
power switch to [ON].
[Windows]
The drive is shown on the [My
computer] folder.
If it is the first time you connect the
camera to PC, the required driver is
installed automatically in order to let
the camera be recognized by the
Windows plug and play, then it is
shown on the [My computer] folder.
[Macintosh]
The drive is shown on the screen.
When connecting to PC, for the power source, it is recommended to use the AC
adaptor.
For further information, read the supplied operating instructions for USB
connection kit.
When recording the motion image, the motion image file (MOV format) and the
still picture file (JPEG format) are produced. The thumbnail of the motion image
files cannot be displayed.
When connecting the camera to PC via the supplied USB cable, the pictures can
be displayed in the thumbnail format, but may not be displayed on the file format.
In this case, open the files after copying them to PC.
V. O U T
USB
KC4-PP.book 66 ページ 2002年1月21日 月曜日 午後7時51分
67
The Menu Items
REC mode menu
1
W.BALANCE (P39)
2
EXPOSURE (P36)
3
BURST (P43)
4
D. ZOOM (P30)
5
MOTION IMAGE (P28)
6
PICT.SIZE (P34)
7
QUALITY (P35)
8
SENSITIVITY (P41)
9
SPOT MODE (P38)
10
MONITOR (P58)
Setup menu
A
11
AUTO REVIEW (P59)
12
BEEP (P60)
13
POWER SAVE (P61)
14
NO. RESET (P62)
15
MEMORY (P63)
16
CLOCK SET (P25)
EXPOSURE
BURST
D.ZOOM
MOTION IMAGE
±0.00
1 / 3
W.BALANCE
PICT.SIZE
QUALITY
SENSITIVITY
SPOT MODE
MONITOR
2 / 3
1600 1024
640
100
ISO
SETUP 3 / 3
SETUP
AUTO REVIEW
BEEP
POWER SAVE
NO.RESET
MEMORY
1 / 2
CLOCK SET
YEAR
MONTH
DAY
TIME
STYLE
2002
MAR
1
19:04
MDY
2 / 2
KC4-PP.book 67 ページ 2002年1月21日 月曜日 午後7時51分
68
The Menu Items (Continued)
Playback mode menu
17
PROTECT (P55)
18
DPOF (P52)
19
SLIDE SHOW (P56)
20
EDIT (P47)
Deleting menu
B
21
SELECT (P50)
22
ALL (P51)
23
FORMAT (P57)
PROTECT
PROTECT
DPOF
SLIDE SHOW
EDIT
DELETE
SELECT
ALL
FORMAT
KC4-PP.book 68 ページ 2002年1月21日 月曜日 午後7時51分
69
Cautions for Use
ª Cautions for Use
Keep the digital camera away from
magnetized equipment (such as a
microwave oven, TV, video game
equipment, etc.).
If you use the digital camera on or
near a TV, images may be
disturbed due to electromagnetic
wave radiation.
Do not use near a cell phone
because doing so may cause noise
to adversely affect the images.
By strong magnetic fields created
by speakers or large motors,
recorded data may be damaged, or
images may be distorted.
Electromagnetic wave radiation
generated by a microprocessor may
adversely affect the digital camera,
causing the disturbance of images.
If the digital camera is affected by
magnetically charged equipment
and does not function properly, turn
the camera off and detach the
battery or AC adaptor and then
connect the battery or AC adaptor
again. Thereafter, turn the camera
on.
Do not use the digital camera near
radio transmitters or high-voltage
lines.
If you record near radio transmitters
or high-voltage lines, recorded
images may be adversely affected.
Do not spray insecticides or
volatile chemicals onto the digital
camera.
If the digital camera is sprayed with
such chemicals, the camera body
may be deformed and the surface
finish may peel off.
Do not keep rubber or plastic
product in contact with the digital
camera for a long period of time.
When you use the digital camera
on a beach or similar place, do not
let sand or fine dust get into the
camera.
Sand or dust may damage the
digital camera or card. (Care should
be taken when inserting and
removing the card)
When you use your digital camera
in a rainy or snowy day or on a
beach, make sure that no water
enters inside the digital camera.
Water may cause the digital camera
or card to malfunction. (Irreparable
failure may occur)
If sea water splashes onto the
digital camera, wet a soft cloth with
tap water, wring it well, and use it to
wipe the camera body carefully.
Then, wipe it again thoroughly with
a soft dry cloth.
Do not use the digital camera for
surveillance purpose or other
business use.
If you use the digital camera for a
long period of time, the internal
temperature increases and,
consequently, this may cause
malfunction.
The digital camera is not intended
for business use.
Do not use benzine, thinner or
alcohol for cleaning the digital
camera.
The camera body may be deformed
and the surface finish may peel off.
Before cleaning the camera, detach
the battery or pull out the AC
adaptor from the electrical outlet.
KC4-PP.book 69 ページ 2002年1月21日 月曜日 午後7時51分
70
Wipe the digital camera with a soft
dry cloth. To remove stubborn
stains, wipe with a cloth that is
soaked in a detergent diluted with
water and afterward finish wiping
with a dry cloth.
For storing or transporting the digital
camera, place it in a bag or case
lined with soft pads so as to prevent
the coating on the camera body
from being worn.
After use, be sure to take the card
out, and detach the battery or pull
out the AC adaptor from the
electrical outlet.
If the battery is left on the digital
camera for a long time, the voltage
drops excessively, and the battery
will not function even after it is
recharged.
ª Optimal Use of the Battery
The battery is a rechargeable lithium
ion battery. Its ability to generate
power is based upon the chemical
reaction that takes place inside it.
This reaction is susceptible to the
surrounding temperature and
humidity, and, if the temperature is
too high or too low, the operating time
of the battery becomes shorter.
Be sure to detach the battery after
use.
Be sure to detach the battery from the
digital camera. (If it is left attached to
the digital camera, a minute amount
of current is consumed even when
the digital camera power is off) If the
battery is left attached to the digital
camera for a long time, over
discharge takes place. The battery
may become unusable after it is
charged.
Dispose of an unusable battery.
The battery has a limited life.
Do not throw the battery into fire
because it may cause an explosion.
Always keep the terminals of the
battery clean.
Prevent the terminals from getting
clogged with dirt, dust, or other
substances.
If you drop the battery accidentally,
check to see if the battery body and
terminals are deformed. Attaching a
deformed battery to the digital
camera may damage the camera.
ª Condensation
When the condensation has
taken place:
Turn the camera off and leave the
digital camera in this condition for
about 1 hour. When the camera
becomes close to the ambient
temperature, the fog disappears
naturally.
ª Cautions for Storage
Before storing the digital camera,
take the card out and detach the
battery.
Store all the components in a dry
place with a relatively stable
temperature.
(Recommended temperature:15 to 25
o
C,
Recommended humidity: 40 to 60 %)
Digital camera
Wrap it with a soft cloth to prevent
dust from getting into the camera.
Do not leave the camera in places
that expose it to high temperature.
KC4-PP.book 70 ページ 2002年1月21日 月曜日 午後7時51分
71
Battery
Extremely high or low temperatures
will shorten the life of the battery.
If the battery is kept in smoky or
dusty places, the terminal may rust
and cause malfunctions.
Do not allow the battery terminals
to come in contact with metal
objects (such as necklaces,
hairpins, etc.). This can result in
a short circuit or heat generation
and, if you touch the battery in
this condition, you may be badly
burned.
Store the battery in a completely
discharged state. To store the
battery for a long period of time, we
recommend you charge it once
every year and store it again after
you completely use up the charged
capacity.
Card
When the card is being read, do not
remove the card, turn the camera
off, or subject it to vibration or
impact.
Do not leave the card in places
where there is high temperature or
direct sunlight, or where
electromagnetic waves or static
electricity are easily generated.
Do not bend or drop the card. The
card or the recorded content may
be damaged.
After use, be sure to remove the
card from the digital camera.
Do not touch the terminals on the
back of the card with your fingers.
Do not allow dirt, dust or water to
enter it.
ª LCD Monitor/Viewfinder
LCD monitor
In a place with drastic temperature
changes, condensation may form
on the LCD monitor. Wipe it with
soft dry cloth.
If the digital camera is extremely
cold when you turn the power on,
the image on the LCD monitor is
slightly darker than usual at first.
However, as the internal
temperature increases, it goes back
to the normal brightness.
.........................................................
Extremely high precision technology
is employed to produce the LCD
monitor screen featuring a total of
approximately 110,000 pixels. The
result is more than 99.99% effective
pixels with a mere 0.01% of the pixels
inactive or always lit. However, this is
not a malfunction and does not affect
the recorded picture.
.........................................................
Viewfinder
Do not direct the viewfinder or lens
to the sun. Internal components
may be seriously damaged.
ª SD Slide Show
If setting the SD slide show with the
[SD Viewer for DSC] which is in the
supplied CD-ROM, when playing
back, the message [START SD
SLIDE SHOW] is displayed. Press
the [MENU] button for normal
playback and press the [REVIEW/
SET] button to start the SD slide
show.
KC4-PP.book 71 ページ 2002年1月21日 月曜日 午後7時51分
72
ª Folder Composition
When the memory card where data
are recorded is inserted into a PC,
the folders shown below will be
displayed.
In the 100_PANA folder it is
possible to record up to 999
images.
In the MISC folder it is possible to
record the files that have been set
with DPOF settings.
100_PANA
MISC
EXPORT
DCIM
SD memory
card
KC4-PP.book 72 ページ 2002年1月21日 月曜日 午後7時51分
73
Warning Indication
[NO MEMORY CARD]
Insert the memory card.
[WRITE PROTECTED]
Cancel the memory card lock.
[NO VALID IMAGE TO PLAY]
Carry out playback after recording or
after inserting the memory card
where there is the recorded image.
[MEMORY FULL]
Insert a new memory card or delete
the useless data.
[MEMORY CARD ERROR]
Failed access to memory card.
Insert the card again.
[READ ERROR]
Data reading error.
Play it back again.
[WRITE ERROR]
Data writing error.
Take out the card, or turn the camera
[ON] again after once turning it [OFF].
Or the card may be destroyed.
[PROTECTED]/
[PROTECTED IMAGE LEFT]
After cancelling the protect setting,
you can delete or overwrite the
image.
[NUMBER OF PRINT IS OVER]
You have exceeded the number of
images that can be set at once, with
multi deleting, protect and DPOF
settings.
[CANT BE SET ON THIS PICTURE]
/ [CANT BE SET ON SOME
PICTURES]
If the image is not based on the DCF
standard, it is not possible to set the
DPOF.
[MEMORY CARD ERROR
FORMAT THIS CARD?]
The format of this card cannot be
recognized by the camera. Format
this again with the camera.
[PLEASE SET THE DATE/TIME]
Set the date.
KC4-PP.book 73 ページ 2002年1月21日 月曜日 午後7時51分
74
Troubleshooting
1: The power does not turn on.
1-1: Are the battery and the AC
adaptor correctly connected?
Check the connection.
1-2: Is the battery sufficiently
charged? Use battery that has
been sufficiently charged.
1-3: Is the REC/power switch slided
fully?
2: As the power is turned on, it
turns off immediately.
2-1: Is the battery charge insufficient
to operate the camera? Charge
the battery or replace it with
charged one.
2-2: Has the condensation occurred?
Carrying the digital camera from
a cold place to a warm place, it
could happen that the
condensation form inside the
camera. Wait until the
condensation disappears.
3: The image cannot be
recorded.
3-1: Is the memory card inside?
3-2: There is no capacity of the card.
Before recording, delete some
images.
3-3: Is the REC/power switch slided
fully?
4: The image is not displayed on
the LCD monitor.
4: Is the LCD monitor set to off?
5: The LCD monitor is too bright
or dark.
5: Adjust the brightness of the LCD
monitor.
6: The flash does not light.
6: The flash mode is set to forced
OFF. Change the flash mode.
7: The image cannot be played
back.
7-1: Is the memory card inside?
7-2: There are no images in the
memory card.
7-3: Is the playback/power switch
slided?
8: The settings are not
memorized.
8-1: [MEMORY] may be set to [OFF].
9: The LCD monitor cannot be
set to off.
9-1: [D.ZOOM] may be set to [ON].
10: The image is not displayed on
the TV.
10-1:Is the camera correctly
connected with the TV? Check it.
10-2:Set the TV to video input mode.
11: When connecting to PC,
images cannot be transferred.
11: Is the camera correctly
connected with PC? Check it.
KC4-PP.book 74 ページ 2002年1月21日 月曜日 午後7時51分
75
Specifications
Digital Camera
information for your safety
Power Source: DC 5 V
Power Consumption: 3.0 W (When recording with LCD Monitor to on)
2.5 W (When recording with LCD Monitor to off)
Effective number of pixels 2.0 M
Image sensor 1/2.7 inch CCD, pixel number 2,110,000
Primary color filter
Lens Optical
a
2 zoom, f=5.3 - 10.6 mm (35 mm film
camera conversion: 35 - 70 mm)/F2.8 - 4.0
Digital zoom
a
2 (800
a
600 pixels)/
a
2.5 (640
a
480 pixels)
Focus Auto/Macro/
Recording range Auto: 50 cm -
, Macro: 10 - 100 cm
Shutter system Electronic shutter + Mechanical shutter
Burst recording 4 frames/second, Max 5 frames
Motion image recording 320
a
240, 20 seconds
ISO sensitivity 100/200/400
Shutter speed 2 - 1/2,000
White balance AUTO/Daylight/Cloudy/Halogen/Night scene/
White set
Exposure (AE) Program AE (P)
Exposure compensation (0.25 EV Step, -2 - +2
EV)
Metering mode Evaluation metering/Spot
LCD monitor 1,5 inch TFT LCD (60,000 pixels)
Optical finder Real-image zoom finder
Flash Built-in flash
Recording range: (Wide) approx. 30 cm - 2.0 m
(Tele) approx. 30 cm - 1.4 m
AUTO, AUTO/Red-eye reduction, Slow synchro,
Forced OFF
Recording media SD Memory Card/MultiMediaCard
Recording size 1600
a
1200, 800
a
600, 640
a
480,
320
a
240 (Motion image mode)
Quality Fine/Standard
Recording file format
Still Picture JPEG (Design rule for Camera File system),
DPOF corresponding
Motion image
QuickTime Motion JPEG
KC4-PP.book 75 ページ 2002年1月21日 月曜日 午後7時51分
76
Interface
Digital USB
Analog video NTSC Composit
Terminal
USB 5 pin Mini USB
Analog video/audio
2,5 mm jack
DC IN EIAJ type 2 jack
Dimensions (W
a
H
a
D) 4.09
a2.00a1.24 inch /
104
a
50.9
a
31.6 mm
(excluding the projection part)
Weight 5.29 oz / 150
g
(excluding memory card and
battery)
6.53 oz / 180
g
(with memory card and battery)
AC adaptor
Panasonic DE-873D
information for your safety
Input USA&CANADA 120 V, 60 Hz, 0.2 A
Foreign 110 V - 240 V 50/60 Hz, 0.2 A
Output 5.3 V 1 A
Battery pack (lithium-ion)
Panasonic CGA-S101A
information for your safety
Voltage/capacity 3,6 V, 700 mAh
KC4-PP.book 76 ページ 2002年1月21日 月曜日 午後7時51分
77
Digital Camera Accessory System
*Please refer to page P15, concerning the battery charging time and available
recording time.
Accessory#
Description
Figure
RP-SD064
RP-SD032
RP-SD016
BN-SDCAPU/1BS
CGA-S101A Lithium Battery
BN-SDABPE
512 MB SD Memory Card
256 MB SD Memory Card
128 MB SD Memory Card
64 MB SD Memory Card
32 MB SD Memory Card
16 MB SD Memory Card
8 MB SD Memory Card
USB Reader/Writer for
SD Memory Card
(compatible with
MultiMediaCard)
SD PCMCIA Adaptor
(compatible with
MultiMediaCard)
RP-SD008
RP-SDH128
RP-SDH256
RP-SDH512
KC4-PP.book 77 ページ 2002年1月21日 月曜日 午後7時51分
78
Digital Camera Accessory Order Form
TO OBTAIN ANY OF OUR DIGITAL CAMERA ACCESSORIES YOU CAN DO ANY OF
THE FOLLOWING:
VISIT YOUR LOCAL PANASONIC DEALER
OR
CALL PANASONICS ACCESSORY ORDER LINE AT 1-800-332-5368
[6 AM-5 PM M-F, 6 AM-10:30 AM SAT, PACIFIC TIME]
OR
MAIL THIS ORDER TO: PANASONIC SERVICES COMPANY ACCESSORY ORDER OFFICE
20421 84th Avenue South Kent, WA. 98032
Ship To:
Mr.
Mrs.
Ms.
First Last
Street Address
City State Zip
Phone#:
Day ( )
Night ( )
4. Shipping information (UPS delivery requires complete street address)
Please photocopy this form when placing an order.
3. Method of payment (check one)
Check of Money Order enclosed (NO C.O.D.SHIPMENTS)
VISA
MasterCard
Make Check or Money Order to: PANASONIC ACCESSORIES
(Please do not send cash)
2. Items Ordered
QuantityAccessory # Price Each Description
Total Price
6.95
Subtotal
Your State & Local Sales Tax
Shipping & Handling
Total Enclosed
1. Digital Camera Model #
Discover
Expiration Date
Credit Card #
Customer Signature
KC4-PP.book 78 ページ 2002年1月21日 月曜日 午後7時51分
79
Request for Service Notice
Mail this completed form and your Proof of Purchase along with your unit to:
Panasonic Services Company
1705 N. Randall Road
Elgin, IL. 60123-7847
Attn: Digital Camera Repair
Request for Service Notice:
(USA Only)
Please photocopy this form when making a request for service notice.
In the unlikely event this product needs service.
Please include your proof of purchase.
(Failure to due so will delay your repair.)
To further speed your repair, please provide
an explanation of what wrong with the unit
and any symptom it is exhibiting.
Please write the displayed above Self Diagnostic number
here.
KC4-PP.book 79 ページ 2002年1月21日 月曜日 午後7時51分
80
Limited Warranty
(For USA Customers)
PANASONIC CONSUMER
ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA
ELECTRIC CORPORATION OF
AMERICA, One Panasonic Way
Secaucus, New Jersey 07094
PANASONIC SALES COMPANY,
DIVISION OF MATSUSHITA
ELECTRIC OF PUERTO RICO, INC.
Ave. 65 de Infanteria, Km. 9.5 San
Gabriel Industrial Park Carolina,
Puerto Rico 00985
Panasonic Digital Still Camera
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or
workmanship, Panasonic Consumer Electronics Company or Panasonic Sales
Company (collectively referred to as the warrantor) will, for the length of the
period indicated on the chart below, which starts with the date of original
purchase (warranty period), at its option either (a) repair your product with
new or refurbished parts, or (b) replace it with a new or refurbished product.
The decision to repair or replace will be made by the warrantor.
During the Labor warranty period there will be no charge for labor. During the
Parts warranty period, there will be no charge for parts. You must carry-in or
mail-in your product during the warranty period. If non-rechargeable batteries
are included, they are not warranted. This warranty only applies to products
purchased and serviced in the United States or Puerto Rico. This warranty is
extended only to the original purchaser of a new product which was not sold
as is. A purchase receipt or other proof of the original purchase date is
required for warranty service.
PARTS LABOR
ALL PARTS (EXCEPT CCD,
RECHARGEABLE BATTERY
PACK AND MEMORY CARD)
1 (ONE) YEAR 90 (NINETY) DAYS
CCD 6 (SIX) MONTHS 90 (NINETY) DAYS
RECHARGEABLE BATTERY
PACK (IN EXCHANGE FOR
DEFECTIVE BATTERY PACK)
90 (NINETY) DAYS N/A
SD MEMORY CARD (IN
EXCHANGE FOR
DEFECTIVE SD CARD)
90 (NINETY) DAYS N/A
KC4-PP.book 80 ページ 2002年1月21日 月曜日 午後7時51分
81
Carry-In or Mail-In Service
For Carry-In or Mail-In Service (as applicable) in the United States call
1-800-272-7033.
For assistance in Puerto Rico call Panasonic Sales Company
(787)-750-4300 or fax (787)-768-2910.
This warranty ONLY COVERS failures due to defects in materials or
workmanship, and DOES NOT COVER normal wear and tear or cosmetic
damage. The warranty ALSO DOES NOT COVER damages which
occurred in shipment, or failures which are caused by products not
supplied by the warrantor, or failures which result from accidents, misuse,
abuse, neglect, mishandling, misapplication, alteration, faulty installation,
set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, or
commercial use (such as in a hotel, office, restaurant, or other business),
rental use of the product, service by anyone other than a Factory
Servicenter or other Authorized Servicer, or damage that is attributable to
acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED
UNDER
LIMITED WARRANTY COVERAGE
. THE WARRANTOR IS
NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes
damages for lost time, travel to and from the servicer, or loss of images,
data or other memory content. The items listed are not exclusive, but are
for illustration only.) ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED
TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or conse-
quential damages, or limitations on how long an implied warranty lasts, so
the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have others
rights which vary from state to state. If a problem with this product
develops during or after the warranty period, you may contact your dealer
or Servicenter. If the problem is not handled to your satisfaction, then write
to the warrantor's Consumer Affairs Department at the addresses listed for
the warrantor.
PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY ARE YOUR RESPONSIBILITY.
KC4-PP.book 81 ページ 2002年1月21日 月曜日 午後7時51分
82
Warranty
(For Canadian Customers)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
PANASONIC PRODUCT LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in
material and workmanship and agrees to remedy any such defect for a period
as stated below from the date of original purchase.
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada or to any
product which has been improperly installed, subjected to usage for which the
product was not designed, misused or abused, damaged during shipping, or
which has been altered or repaired in any way that affects the reliability or
detracts from the performance, nor does it cover any product which is used
commercially. Dry cell batteries are also excluded from coverage under this
warranty.
This warranty is extended to the original end user purchaser only. A purchase
receipt or other proof of date of original purchase is required before warranty
service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, EXCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation
of incidental or consequential damages, or the exclusion of implied warranties,
so the above limitations and exclusions may not be applicable.
Digital Camera One (1) year, parts and labour
Digital Photo Printer One (1) year, parts and labour
Digital Camera Accessories Ninety (90) days, parts and labour
KC4-PP.book 82 ページ 2002年1月21日 月曜日 午後7時51分
83
WARRANTY SERVICE
For product operation and information assistance, please contact your
Dealer or our Customer Care Centre at:
Telephone #: (905) 624-5505 Fax #: (905) 238-2360
Web: www.panasonic.ca
For product repairs
, please contact one of the following:
Your Dealer who will inform you of an authorized Servicentre nearest you.
Our Customer Care Centre at (905) 624-5505 or www.panasonic.ca
A Panasonic Factory Servicentre listed below:
Richmond, British Columbia
Panasonic Canada Inc.
12111 Riverside Way
Richmond, BC V6W 1K8
Tel: (604) 278-4211
Fax: (604) 278-5627
Mississauga, Ontario
Panasonic Canada Inc.
5770 Ambler Dr.
Mississauga, ON L4W 2T3
Tel: (905) 624-8447
Fax: (905) 238-2418
Calgary, Alberta
Panasonic Canada Inc.
6835-8
th
St. N. E.
Calgary, AB T2E 7H7
Tel: (403) 295-3955
Fax: (403) 274-5493
Lachine, Québec
Panasonic Canada Inc.
3075, rue Louis A. Amos
Lachine, QC H8T 1C4
Tel: (514) 633-8684
Fax: (514) 633-8020
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
CUSTOMERS RECORD
Customer Name:__________________ Model Number: _______________
Serial Number: ________________________________________________
Date of Purchase:______________________________________________
Dealers Name: ________________________________________________
Address: ___________________________ Phone Number:____________
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the
original carton.
Include details of the defect claimed, and proof of date of original purchase.
KC4-PP.book 83 ページ 2002年1月21日 月曜日 午後7時51分
84
Servicenter List
Factory Servicenters Locations
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)
(Visa, MasterCard, Discover Card, American Express, Check)
MINNESOTA
7850-12th Avenue South
Airport Business Center
OHIO
2236 Waycross Road
Civic Center Plaza
Forest Park, OH 45240
PENNSYLVANIA
2221 Cabot Blvd. West
Suite B
Langhorne, PA 19047
GEORGIA
8655 Roswell Road
Suite 100
Atlanta, GA 30350
ILLINOIS
Elgin, IL 60123
MASSACHUSETTS
Suite G
TEXAS
13615 Welch Road
Suite 101
Farmers Branch,
TX 75244
WASHINGTON
20425-84th Avenue
South
Kent, WA 98032
HAWAII
99-859 Iwaiwa Street
Aiea, Hawaii 96701
Phone (808) 488-1996
Fax (808) 486-4369
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your nearest
servicenter by visiting our Web Site.
For Product Information, Operating Assistance, Literature Request, Dealer
Locations, and all Customer Service inquiries please contact:
1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST.
or send e-mail to : consumerproducts@panasonic.com
As of Sep.2001
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infantera, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
CALIFORNIA
6550 Katella Avenue
Cypress, CA 90630
800 Dubuque Avenue
S. San Francisco,
CA 94080
3878 Ruffin Road
Suite A
San Diego, CA 92123
FLORIDA
3700 North 29th Avenue
Suite 102
Hollywood, FL 33020
Accessory Purchases:
60 Glacier Drive
Westwood, MA 02090
KC4-PP.book 84 ページ 2002年1月21日 月曜日 午後7時51分
85
Index
A
AF/AE Lock
...........................37
Auto Review
..........................59
B
Beep Sound
..........................60
Built-in Flash
.........................31
Burst Mode
...........................43
C
Clock Set
..............................25
Condensation
........................70
D
Digital Zoom
..........................30
DPOF
...................................52
E
Editing
..................................47
Exposure Compensation
.........36
F
File Number
..........................62
Flash Indicator
.......................22
Formatting
.............................57
I
ISO Sensitivity
.......................41
L
LCD Monitor Brightness
..........58
M
Macro Mode
..........................42
Memory Setting
.....................63
Motion Images
.......................28
Multi Playback
.......................45
MultiMediaCard
.....................17
O
Optical Zoom
.........................29
P
Picture Size
...........................34
Playback Zoom
......................46
Power Save Mode
..................61
Q
Quality
..................................35
R
Review
.................................27
S
SD memory card
....................17
SD Slide Show
......................71
Self-timer
..............................33
Slide Show
............................56
Spot AF
................................38
Status Indicator
.....................22
W
White Balance
.......................39
KC4-PP.book 85 ページ 2002年1月21日 月曜日 午後7時51分
86
Spanish Quick Use Guide/Guía española
para el uso rápido
Prepare las siguientes piezas.
Cámara
Batería
Tarjeta de memoria
Adaptador AC
Verifique que el interruptor de alimentación
esté en [OFF].
1
Inserte la batería en la cámara.
2
Para cargar la batería, conecte el
adaptador AC a la cámara.
3
Introduzca la tarjeta de memoria en
la cámara.
A: Terminal de conexión detrás de
la tarjeta.
4
Ponga Grabación/Interruptor de
alimentación en [ON].
5
Defina la fecha.
6
Pulse el botón del obturador a mitad
para arreglar el enfoque.
7
Pulse el botón del obturador para
sacar una imagen.
[Reproducción]
8
Ponga Reproducción/Interruptor de
alimentación en [ON].
9
Pulse
2/1
para reproducir la
imagen que quiere ver.
1
2
3
A
4
8
6,7
9
KC4-PP.book 86 ページ 2002年1月21日 月曜日 午後7時51分
87
Memo
KC4-PP.book 87 ページ 2002年1月21日 月曜日 午後7時51分
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
Division of Matsushita Electric Corporation of America
Executive Office:
One Panasonic Way, Secaucus, NJ 07094
(201) 348-7000
Panasonic Company East: 6749 Baymeadow Drive, Glen Burnie, MD 21060
Panasonic Company Central: 1707 North Randall Road, Elgin, IL 60123
Panasonic Company West: 6550 Katella Avenue, Cypress, CA 90630
Panasonic Sales Company ("PSC")
Division of Matsushita Electric of Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infanteria, Km. 9.5, Carolina, PR 00984
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, ON, L4W 2T3
P
KC4-PP.book 89 ページ 2002年1月21日 月曜日 午後7時51分
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic DMC-F7PP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic DMC-F7PP in de taal/talen: Engels als bijlage per email.

De handleiding is 3,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info