99987
46
Verklein
Vergroot
Pagina terug
1/134
Pagina verder
46
1
Set the POWER switch to ON.
2
Set the TCG switch to F-RUN.
4
Supply the reference time code and reference video
signal, which are in a phase relationship that satisfies
the time code standard, to the TC IN connector and
GENLOCK IN connector respectively.
3
Set the DISPLAY switch to TC.
Operating procedure for external locking
Follow the steps below for external locking.
The built-in time code generator is now locked to the
reference time code.
About 10 seconds after locking, the external lock status will
be retained even if the connection of the externally supplied
reference time code is disconnected. However, the servo
lock will be subject to disturbances if it is connected or
disconnected during recording.
O When the power of the unit is turned off, the time code is
unlocked.
O The accuracy of the time code is ± 20 seconds a month.
<Note>
When the external lock operation is performed, the time code
is instantly locked to the external time code, and the same
value as the external code value appears on the counter
display. Do not set the unit to the recording mode during the
few seconds it takes for the sync generator to stabilize.
Concerning the user bits setting during external
lock
When the unit’s time code is externally locked, only the time
data is locked to the time data of the time code supplied from
the external source. This means that the user bits can be set
separately for each component.
When the <TC/UB> screen is opened from the VTR menu
page and EXT is selected as the UB MODE item setting by
performing menu operations, the user bits can also be locked
to the user bits of the time code supplied from the external
source.
To release the external lock
First stop supplying the external time code, and set the TCG
switch to R-RUN.
Chapter 4 Adjustments and settings for recording
(continued)
TCG
TC OUT
TC OUT
TC IN
TC IN
AJ-HDX900
TC OUT
AJ-HDX900
GENLOCK IN
GENLOCK IN
GENLOCK IN
TC IN
TC OUT
AJ-HDX900
TC IN
DAT
1st unit
Settings of the TC
VIDEO SYNCRO item: 1
From the 2nd unit to the
(n–1)-th unit
n-th unit
Settings of the TC
VIDEO SYNCRO item: 0
Settings of the TC
VIDEO SYNCRO item: 2
Example 6:
When an external device is locked to the time code
generator of this unit, which is connected in a cascade
configuration.
To be connected if necessary
A device that synchronizes with the TC IN
input and capable to record without delay
(such as DAT or a camera recorder)
Reference video signal
01.AJ-HDX900_P_E(VQT0X86)_E 06.6.27 6:01 PM ページ46
46

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Panasonic AJ-HDX900 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Panasonic AJ-HDX900 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info