Handleiding Oregon Scientific WMR300 (pagina 10 van 131) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds)

677397

Verklein

Vergroot

Pagina terug

1/131

Pagina verder

NOTE

Heat index is only calculated when temperature is 80° F / 27°C or above.

To view wind chill:

• Press area repeatedly until WIND CHILL displays.

SUNRISE / SUNSET

NOTE

Make sure you input latitude and longitude of your location in area,

which affects the sunrise/sunset time.

NOTE

Excepting the latitude and longitude, daylight saving time setting also affects

sunrise and sunset (See Manually Set Clock).

You can view the sunrise or sunset time in area.

•

Press SUNRISE/SUNSET area. displays on the top of the time display.

• Press to change the time display between 12hr/24hr format.

WIND

DIRECTION CALIBRATION

Before pairing a wind sensor, make sure the head of the wind vane of that sensor

point to the north while pressing KEY for 2 seconds in the transmitter box to calibrate

the direction. If the calibration is successful, red light ﬂashes once. You can use a

compass to look for an accurate direction of north if necessary.

However, if you are the user in North America, there are already 15°(degree)

variations existing between the true north and a compass reading of north. You

can consult your local observatory about this issue.

If it is difﬁcult to control the wind vane after installation, you can calibrate through

setting on main unit.

1. Make a compass approach to the wind vane.

2. Calculate the angle between the current direction

and the north direction.

3. Press wind area to activate.

4. Press and hold , and then

press or to calibrate

the angle value.

5. Press again to conﬁrm setting.

For example, inputting the angle value that you

want to set as north. If current direction is 25

degree and you want to set it as north, then you

input 25 degree in the calibration mode. Once

you return to the idol mode, the direction reading

displays 0 degree, which is the north.

NOTE

You need to calibrate the wind sensor again if you want to relocate the sensor.

WIND SPEED / DIRECTION

To select wind display mode:

Press wind area to toggle between:

• GUST (Gust)

• AVG (Average)

To select wind speed unit:

Press to switch among:

• Knots (knots)

• Kilometres per hour (km/h)

• Miles per hour (mph)

• Metres per seconds (m/s)

The wind level is shown by a series of text icons:

LIGHT MODERATE STRONG STORM

2-8 mph

(3-13 km/h)

9-25 mph

(14-41 km/h)

26-54 mph

(42-87 km/h)

>55 mph

(>88 km/h)

To read the wind direction:

Status Wind Direction Indicator Meaning

GUST Real-time wind direction

AVG Real-time average wind direction

AVG (Max 6 sets) Wind direction of last 1 hour

RESET KEY

North

NOTE

The wind chill factor is based on the combined effects of temperature and

wind speed. Displayed wind chill is calculated solely from channel 1 thermometer

and humidity sensor.

BAROMETRIC PRESSURE

The altitude reﬂects distance from sea level at your position.

To set the altitude level compensation for the barometric readings:

1. Press area to activate. displays next to the area and the tool bar

displays at the below of the screen.

2. Press the area until ALT displays on the screen. You are in altitude mode.

3. Press and hold on the tool bar.

4. Press or to edit. You can press to change the

altitude unit between M (Meter) and FEET (Feet) while editing.

5. Press to conﬁrm or touch panel area (except tool bar/barometer

area) to conﬁrm.

6. After setting altitude, the new altitude setting will not be effective immediately.

The ALT icon ﬂashes and stops ﬂashing until the next pressure sampling. The

new altitude setting takes effect on the new pressure sampling.

NOTE

When altitude is set to 0 meter, the pressure reading is the local pressure.

If the altitude is set to the current location, the new pressure reading is an offset

pressure to the sea level.

To select the measurement unit for the barometer:

1. Press barometer area to toggle between altitude and current barometer.

2. Press to select inHg (inches of mercury) / mmHg (millimetres of

mercury) / mb (millibars per hectopascal) / hPa.

To view pressure trend:

The barometric pressure trend icons are based on recent sensor readings.

The trend lines are shown next to the pressure readings. The trend is shown

as follows:

Rising Steady Falling

RAINFALL

To select rainfall display mode:

Press rain area to toggle between:

• THIS HOUR (Hourly rainfall)

• RATE (Rain rate)

• ACCUM (Accumulated rainfall)

• PAST 24 hrs (Rainfall recorded in the past 24 hours)

To select the measurement unit for the rainfall:

Press to select between mm (millimeter) and in (inch).

To select the measurement unit for the rainfall rate:

Press to select between in/hr (inch per hour) and mm/hr (millimeter

per hour).

ACCUMULATED RAINFALL

To display accumulated rainfall:

Press rain area repeatedly until ACCUM display. (SINCE displays in the

clock area that displays the start date / time of rainfall recording simultaneously).

To reset SINCE time:

Press and hold MEM to set current time as start of accumulated rainfall records.

The rainfall record is cleared and reset to 0.

BAR CHART

The bar chart simultaneously displays the data while you press on the

corresponding area.

To select chart display mode:

Press on the below areas to toggle among these chart displays.

• IN TEMP (Indoor temperature)

• IN HUM (Indoor humidity)

• OUT TEMP (Outdoor temperature)

• OUT HUM (Outdoor humidity)

• DEWPOINT (Dew point)

• HEAT INDEX (Heat index)

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Oregon Scientific WMR300 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Oregon Scientific WMR300

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info