492719
24
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
© Calibre UK Limited Issue 1.30 27 January 2012, W: www.calibreuk.com
T:+44 1274 394125 F: +44 1274 730960 E: techsupport@calibreuk..com 20
3.10. Multiple Unit
The HQView-310 and HQView-320 have a Multiple Unit menu to set up each unit for use in a multi
screen application.
Multiple screens are stitched together to provide a bigger display with higher resolution than a single
display. Each display is driven by a separate HQView unit. Each HQView unit gets the same graphics or
video input signal through a distribution amplifier. The HQView unit cuts out and resizes the image to
display the part of the image assigned to the corresponding screen. In a multi projection display the
individual projections typically are chosen to overlap to give seamless transitions. Overlapping regions
are illuminated by multiple projectors and are brighter than non-overlapping regions. For a uniform
brightness over the total display the brightness in the overlapping regions has to be reduced
electronically.
Important: When using multiple HQView units to drive one single large screen, it is essential that all
HQView units are I/O locked, otherwise motion tear will be observed at the boundaries of the image
processed by each HQView unit. It is also essential that all HQView units are setup for the same
processing latency (either all units are in Best Picture mode or all units are in Low Latency mode).
3.10.1. Auto Zoom
Settings: On, Off
Switches on the auto zoom resizing the video image to display the assigned part of the total image.
AutoZoom is switched off automatically when the on-screen menu is activated and that menu cannot be
properly displayed. The menu is scaled to a certain extend by the warp engine and may exceed the size
of the screen. Also, only the active video area can be used for the on-screen menu. This would crop the
menu and make it impossible to navigate. A message will indicate such situations. After having done the
change AutoZoom can be reactivated.
3.10.2. Units Wide/Units High
Settings: 1, 2, 3, 4/ 1, 2, 3, 4
Provides the HQView unit information of the multi screen installation. The number of horizontally and
vertically installed screens or projectors is entered.
3.10.3. Horizontal Pos/Vertical Pos
Settings: 0 to (Units Wide 1) in steps of 1/ 0 to (Units High 1) in steps of 1
Provides the HQView unit information which window of the total image it is assigned to and has to
process (cut out and resize).
3.10.4. Blend Width
The blend width menu provides sliders to set up the overlap region for left, right, top and bottom blend
region. The overlap is set up in output pixels with a range of up to a quarter of the output resolution. For
a configuration with two projectors in horizontal direction the overlap can be higher to allow 16:9 images
to fit on two combined projectors with an aspect ratio of 4:3 or 5:4.
An offset for the blend region can be set-up as well. The region between the edge and the start of the
blend area is black. The total pixels of blend area and offset region is limited by the same amount of
pixels as for an offset of zero.
Note: Each HQView unit needs to be provided with the exact same value for left and right blend region.
Top and bottom blend region have to be identical as well, but don´t need to have the same value as left
and right. The HQView units do not communicate between each other and thus they have to make an
assumption for auto zoom calculations and that is overlap of the neighbouring (and those beyond)
projectors is identical.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Optoma HQView-300 Series bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Optoma HQView-300 Series in de taal/talen: Engels als bijlage per email.

De handleiding is 1,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info