721751
11
Verklein
Vergroot
Pagina terug
1/59
Pagina verder
User manual
DLP
®
Projector
English
2
TABLE OF CONTENTS
SAFETY ............................................................................................... 4
Important Safety Instruction....................................................................................................... 4
3D Safety Information ................................................................................................................ 5
Copyright ................................................................................................................................... 6
Disclaimer .................................................................................................................................. 6
Trademark Recognition ............................................................................................................. 6
FCC ........................................................................................................................................... 7
Declaration of Conformity for EU countries ............................................................................... 7
WEEE ........................................................................................................................................ 7
INTRODUCTION .................................................................................. 8
Package Overview..................................................................................................................... 8
Standard accessories ................................................................................................................ 8
Optional accessories ................................................................................................................. 8
Product Overview ...................................................................................................................... 9
Connections.............................................................................................................................. 10
Keypad ..................................................................................................................................... 11
Remote control ......................................................................................................................... 12
SETUP AND INSTALLATION ............................................................. 13
Installing the projector .............................................................................................................. 13
Connecting sources to the projector ......................................................................................... 14
Adjusting the projector image ................................................................................................... 16
Remote setup ........................................................................................................................... 17
USING THE PROJECTOR .................................................................. 19
Powering on / off the projector.................................................................................................. 19
Selecting an input source ......................................................................................................... 20
USING THE PROJECTOR .................................................................. 21
Menu navigation and features .................................................................................................. 21
OSD Menu tree......................................................................................................................... 22
Display image settings menu.................................................................................................... 31
Display 3D menu ...................................................................................................................... 33
Display aspect ratio menu ........................................................................................................ 34
Display edge mask menu ......................................................................................................... 37
Display zoom menu .................................................................................................................. 37
Display image shift menu ......................................................................................................... 37
Display keystone menu ............................................................................................................ 37
Audio mute menu ..................................................................................................................... 38
Audio volume menu .................................................................................................................. 38
Setup projection menu.............................................................................................................. 38
English
3
Setup screen type menu........................................................................................................... 38
Setup lamp settings menu ........................................................................................................ 38
Setup lter settings menu ......................................................................................................... 38
Setup power settings menu ...................................................................................................... 39
Setup security menu ................................................................................................................. 40
Setup test pattern menu ........................................................................................................... 41
Setup remote settings menu..................................................................................................... 41
Setup projector ID menu........................................................................................................... 41
Setup options menu.................................................................................................................. 41
Setup reset all menu................................................................................................................. 42
Info menu.................................................................................................................................. 42
MAINTENANCE .................................................................................. 43
Replacing the lamp ................................................................................................................... 43
Installing and cleaning the dust lter ........................................................................................ 45
ADDITIONAL INFORMATION ............................................................ 46
Compatible resolutions ............................................................................................................. 46
Image size and projection distance .......................................................................................... 49
Projector dimensions and ceiling mount installation ................................................................. 50
IR remote codes ....................................................................................................................... 51
Troubleshooting ........................................................................................................................ 53
Warning indicators .................................................................................................................... 55
Specications ........................................................................................................................... 57
Optoma global ofces ............................................................................................................... 58
English
4
SAFETY
The lightning ash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Please follow all warnings, precautions and maintenance as recommended in this user's guide.
Important Safety Instruction
Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from
over heating, it is recommended to install the projector in a location that does not block ventilation.
As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the
projector in an enclosure such as a book case or a cabinet that restricts air ow.
To reduce the risk of re and/or electric shock, do not expose the projector to rain or moisture. Do not
install near heat sources such as radiators, heaters, stoves or any other apparatus such as ampliers
that emits heat.
Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short
out parts that could result in re or electric shock.
Do not use under the following conditions:
In extremely hot, cold or humid environments. ±
(i) Ensure that the ambient room temperature is within 5°C ~ 40°C
(ii) Relative humidity is 10% ~ 85%
In areas susceptible to excessive dust and dirt. ±
Near any appliance generating a strong magnetic eld. ±
In direct sunlight. ±
Do not use the projector in places where ammable gases or explosives gases may be present in the
atmosphere. The lamp inside the projector becomes very hot during operation and the gases may
ignite and result in a re.
Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be
(but not limited to):
Unit has been dropped. ±
Power supply cord or plug has been damaged. ±
Liquid has been spilled on to the projector. ±
Projector has been exposed to rain or moisture. ±
Something has fallen in the projector or something is loose inside. ±
Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the
projector may become damaged.
Do not block the light coming out of the projector lens when in operation. The light will heat the object
and my melt, cause burns or start a re.
Please do not open or disassemble the projector as this may cause electric shock.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous
voltages or other hazards. Please call Optoma before you send the unit for repair.
See projector enclosure for safety related markings.
The unit should only be repaired by appropriate service personnel.
English
5
Only use attachments/accessories specied by the manufacturer.
Do not look into straight into the projector lens during operation. The bright light may harm your eyes.
When replacing the lamp, please allow the unit to cool down. Follow instructions as described on
pages 43-44.
This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows
warning messages.
Reset the "Lamp Reset" function from the on-screen display "Lamp settings" menu after replacing the
lamp module.
When switching the projector off, please ensure the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the projector to cool down.
When the lamp is approaching to the end of its life time, the message "Lamp life exceeded." will show
on the screen. Please contact your local reseller or service center to change the lamp as soon as
possible.
Turn off and unplug the power plug from the AC outlet before cleaning the product.
Use a soft dry cloth with mild detergent to clean the display housing. Do not use abrasive cleaners,
waxes or solvents to clean the unit.
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has beenNote:
replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages
43-44.
Do not setup the projector in places where it might be subjected to vibration or shock.
Do not touch the lens with bare hands
Remove battery/batteries from remote control before storage. If the battery/batteries are left in the
remote for long periods, they may leak.
Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it
can adversely affect the quality of the projector performance.
Please follow the correct projector orientation installation as non standard installation may affect the
projector performance.
Use a power strip and or surge protector. As power outages and brown-outs can KILL devices .
3D Safety Information
Please follow all warnings and precautions as recommended before you or your child use the 3D function.
Warning
Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be
closely supervised when viewing these images.
Photosensitive Seizure Warning and Other Health Risks
Some viewers may experience an epileptic seizure or stroke when exposed to certain ashing images
or lights contained in certain Projector pictures or video games. If you suffer from, or have a family
history of epilepsy or strokes, please consult with a medical specialist before using the 3D function.
Even those without a personal or family history of epilepsy or stroke may have an undiagnosed
condition that can cause photosensitive epileptic seizures.
Pregnant women, the elderly, sufferers of serious medical conditions, those who are sleep deprived or
under the inuence of alcohol should avoid utilizing the unit's 3D functionality.
If you experience any of the following symptoms, stop viewing 3D pictures immediately and consult a
medical specialist: (1) altered vision; (2) light-headedness; (3) dizziness; (4) involuntary movements
such as eye or muscle twitching; (5) confusion; (6) nausea; (7) loss of awareness; (8) convulsions;
(9) cramps; and/ or (10) disorientation. Children and teenagers may be more likely than adults
to experience these symptoms. Parents should monitor their children and ask whether they are
experiencing these symptoms.
English
6
Watching 3D projection may also cause motion sickness, perceptual after effects, disorientation, eye
strain and decreased postural stability. It is recommended that users take frequent breaks to lessen
the potential of these effects. If your eyes show signs of fatigue or dryness or if you have any of the
above symptoms, immediately discontinue use of this device and do not resume using it for at least
thirty minutes after the symptoms have subsided.
Watching 3D projection while sitting too close to the screen for an extended period of time may
damage your eyesight. The ideal viewing distance should be at least three times the screen height. It
is recommended that the viewer's eyes are level with the screen.
Watching 3D projection while wearing 3D glasses for an extended period of time may cause a
headache or fatigue. If you experience a headache, fatigue or dizziness, stop viewing the 3D
projection and rest.
Do not use the 3D glasses for any other purpose than for watching 3D projection.
Wearing the 3D glasses for any other purpose (as general spectacles, sunglasses, protective goggles,
etc.) may be physically harmful to you and may weaken your eyesight.
Viewing in 3D projection may cause disorientation for some viewers. Accordingly, DO NOT place your
3D PROJECTOR near open stairwells, cables, balconies, or other objects that can be tripped over, run
into, knocked down, broken or fallen over.
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright
laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced
without written consent of the author.
© Copyright 2015
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations
or warranties with respect to the contents hereof and specically disclaims any implied warranties of
merchantability or tness for any particular purpose. The manufacturer reserves the right to revise this publication
and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending
applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
DLP , DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor
TM
is a
trademark of Texas Instruments.
All other product names used in this manual are the properties of their respective owners and are
Acknowledged.
DARBEE is a trademark by Darbee Products, Inc.
MHL, Mobile High-Denition Link and the MHL Logo are trademarks or registered trademarks of MHL Licensing,
LLC.
English
7
FCC
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be determined by turning the device off and on is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC
regulations.
Caution
Changes or modications not expressly approved by the manufacturer could void the user's authority, which is
granted by the Federal Communications Commission, to operate this projector.
Operation Conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque l'intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
EMC Directive 2004/108/EC (including amendments)
Low Voltage Directive 2006/95/EC
R & TTE Directive 1999/5/EC (if product has RF function)
WEEE
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure
utmost protection of the global environment, please recycle it.
English
8
INTRODUCTION
Package Overview
Carefully unpack and verify that you have the items listed below under standard accessories. Some of the items
under optional accessories may not be available depending on the model, specication and your region of
purchase. Please check with your place of purchase. Some accessories may vary from region to region.
The warranty card is only supplied in some specic regions. Please consult your dealer for detailed information.
Standard accessories
Carry bag
Optional accessories
Optional accessories vary depending on model, specication and region.Note:
Projector Remote control Power lead Documentation

CD User Manual

Warranty Card*

Basic User Manual
VGA cable
HDMI cable
Note:
The remote control is shipped with the battery.
* For European warranty information please visit www.optomaeurope.com.
English
9
INTRODUCTION
Product Overview
9
786
1 32 54
10
13
12 11
6
Do not block projector inlet or outlet air vents.Note:
(*) optional accessory varies depending on model, specication, and region.
No Item No Item
1. Lamp Cover 8. Lens
2.
Focus Ring
9.
Ventilation (inlet)
3. Zoom Lever 10. Ventilation (outlet)
4. IR Receiver 11. Kensington
TM
Lock Port
5. Keypad 12. Power Socket
6. Tilt-Adjustment Foot 13. Input / Output
7. Security Bar
English
10
INTRODUCTION
Connections
21 3
8
7
5 64
91011
No Item
Regulatory Name
Type 1
SVGA
Type 2
SVGA
Type 3
SVGA &
Type 4
XGA
Type 5
WXGA
Type 6
WXGA
Type 7
1080p
1. HDMI 1 Connector
N/A
P P P P P
2. HDMI 2 / MHL Connector
N/A
P
N/A N/A
P
N/A
3.
USB Power Out (5V 1A) Connector /
MOUSE / SERVICE Connector
P* P P P* P P*
4. VGA-IN / YPbPr Connector
P
N/A
P P P P
5. VGA-OUT / YPbPr Connector
N/A N/A
P
N/A
P
N/A
6. VIDEO Connector
P
N/A
P P P P
7. Audio In Connector
N/A N/A
P P P P
8. Audio Out Connector
N/A
P P P P P
9. RS-232C Connector
N/A N/A
P P P P
10. Kensington
TM
Lock Port
P P P P P P
11. Power Socket
P P P P P P
Note: P” means the item is supported, “N/A” means the item is not available.
Note:
Remote mouse requires special remote control.
*This model supports mouse / service capability.
English
11
INTRODUCTION
Keypad
1 2
6
5
8
3 4
11
9
10
7
No Item No Item
1.
On/Standby LED
7.
Enter
2.
Lamp LED
8.
Menu
3.
Keystone Correction
9.
Four Directional Select Keys
4.
Temp LED
10.
Source
5.
Information
11.
Power
6. Re-Sync
English
12
INTRODUCTION
Remote control
4
1
3
5
6
8
7
9
2
2
15
18
17
16
4
14
13
12
11
10
No Item No Item
1. Power On / Off 10. IR LED Indicator
2.
Keystone + / - 11. Freeze
3. AV Mute 12. Aspect Ratio
4. Volume - / + 13. Mute
5. Enter 14. Four Directional Select Keys
6. Menu 15. 3D
7. HDMI 16. Video
8. VGA 17. Resync
9. Source 18. Lamp Mode
Note:
Some keys may have no function for models that do not support these features.
Before using the remote control for the rst time, remove the transparent insulation tape. See page 17
for battery installation.
3
V
O
L
T
S
CR2025
English
13
SETUP AND INSTALLATION
Installing the projector
Your projector is designed to be installed in one of four possible positions.
Your room layout or personal preference will dictate which installation location you select. Take into consideration
the size and position of your screen, the location of a suitable power outlet, as well as the location and distance
between the projector and the rest of your equipment.
Table mount front Ceiling mount front
Table mount rear Ceiling mount rear
Projector should be placed at on a surface and 90 degrees / perpendicular to the screen.
How to determine projector location for a given screen size, please refer to distance table on page.48.
How to determine screen size for a given distance, please refer to distance table on page 48.
The further away the projector is placed from the screen the projected image size increases and vertical Note:
offset also increases proportionally.
IMPORTANT!
Do not operate the projector in any orientation other that table top or ceiling mount. The projector should
be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate
the warranty and may shorten the lifetime of the projector lamp or the projector itself. For none standard
installation advise please contact Optoma.
English
14
SETUP AND INSTALLATION
Connecting sources to the projector
HDMI 1
Audio Out
Audio In
VIDEO
VGA-IN / YPbPr
RS-232C
VGA-OUT / YPbPr
HDMI 2 / MHL
USB Power
MOUSE
SERVICE
Out (5V 1.0A)
YP
A
A
MOLEX
MOLEX
1
7
9
2
3
5
4
81011
12
14
13
6
No Item
Regulatory Name
Type 1
SVGA
Type 2
SVGA
Type 3
SVGA &
Type 4
XGA
Type 5
WXGA
Type 6
WXGA
Type 7
1080p
1. HDMI Cable
N/A
P P P P P
2. HDMI / MHL Cable
N/A
P
N/A N/A
P
N/A
3.
RCA Component Cable
P
N/A
P P P P
4. VGA Out Cable
N/A N/A
P
N/A
P
N/A
5. Video cable
P
N/A
P P P P
6. Audio In Cable
N/A N/A
P P P P
7. Audio Out Cable
N/A
P P P P P
English
15
SETUP AND INSTALLATION
No Item
Regulatory Name
Type 1
SVGA
Type 2
SVGA
Type 3
SVGA &
Type 4
XGA
Type 5
WXGA
Type 6
WXGA
Type 7
1080p
8. Audio In Cable
N/A N/A
P P P P
9. RS232 Cable
N/A N/A
P P P P
10. VGA In Cable
P
N/A
P P P P
11. USB Cable (mouse control)
P P P P P P
12. USB Power Cable
N/A
P P
N/A
P
N/A
13. HDMI Stick
N/A
P P
N/A
P
N/A
14. Power Cord
P P P P P P
Note: P” means the item is supported, “N/A” means the item is not available.
English
16
SETUP AND INSTALLATION
Adjusting the projector image
Image height
The projector is equipped with elevator feet for adjusting the image height.
Locate the adjustable foot you wish to adjust on the underside of the projector.1.
Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.2.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
Zoom and focus
To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease
the projected image size.
To adjust the focus, turn the focus ring clockwise or counterclockwise until the image is sharp and
legible.
Focus Ring
Zoom Lever
The projector will focus at a distance of 1m to 10.Note:
English
17
SETUP AND INSTALLATION
Remote setup
Installing / replacing the batteries
Press rmly and slide the battery cover off.1.
M
n
O
2
-
L
i
C
E
L
L
3
V
O
L
T
S
J
A
P
A
N
H
CR2025
Install new battery into the compartment. Remove the old battery and 2.
install new one (CR2025). Ensure that the side with a “+” is facing
up.
3
V
O
L
T
S
CR2025
Put the cover back.3.
M
3
V
O
L
T
S
CR2025
CAUTION: To ensure safe operation, please observe the following precautions:
Use CR2025 type battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture or heat.
Do not drop the remote control.
If the battery has leaked in the remote control, carefully wipe the case clean and install new battery.
Risk of an explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the instructions.
English
18
SETUP AND INSTALLATION
Effective range
Infra-Red (IR) remote control sensor is located on the top side of the projector. Ensure to hold the remote control
at an angle within 20 degrees perpendicular to the projector's IR remote control sensor to function correctly. The
distance between the remote control and the sensor should not be longer than 7 meters (~ 23 feet).
Make sure that there are no obstacles between the remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
Make sure the IR transmitter of the remote control is not being shined by sunlight or uorescent lamps
directly.
Please keep the remote controller away from uorescent lamps for over 2 meters or the remote
controller might become malfunction.
If the remote control is closed to Inverter-Type uorescent lamps, it might become ineffective from time
to time.
If the remote control and the projector are within a very short distance, the remote control might
become ineffective.
Approx. 10°
English
19
USING THE PROJECTOR
Powering on / off the projector
or
Powering on
Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will 1.
turn red.
Turn on the projector by pressing the 2. " " either on the projector keypad or the remote control.
A start up screen will display in approximately 10 seconds and the On/Standby LED will be ashing 3.
green or ashing blue.
The rst time the projector is turned on, you will be prompted to select the preferred language, projectionNote:
orientation, and other settings.
Powering off
Turn off the projector by pressing the 1. " " either on the projector keypad or the remote control.
The following message will be displayed:2.
Power Off
Power Off?
Press power key again.
Press the 3. " " again to conrm, otherwise the message will disappear after 15 seconds. When you
press the " " button for the second time, the projector will shut down.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/4.
Standby LED will ash green or ash blue. When the On/Standby LED turns solid red, this indicates
the projector has entered standby mode. If you wish to turn the projector back on, you must wait until
the cooling cycle has nished and the projector has entered standby mode. When the projector is in
standby mode, simply press the " " button again to turn on the projector.
Disconnect the power lead from the electrical outlet and the projector.5.
It is not recommended that the projector is turned on immediately, right after a power off procedure.Note:
English
20
USING THE PROJECTOR
Selecting an input source
Turn on the connected source that you want to display on the screen, such as computer, notebook, video player,
etc. The projector will automatically detect the source. If multiple sources are connected, push the source button on
the projector keypad or the remote control to select the desired input.
or
English
21
USING THE PROJECTOR
Menu navigation and features
The projector has multilingual on-screen display menus that allow you to make image adjustments and change a
variety of settings. The projector will automatically detect the source.
To open the OSD menu, press 1. on the remote control or the projector keyboard.
When OSD is displayed, use 2. keys to select any item in the main menu. While making a selection
on a particular page, press or key to enter sub menu.
Use 3. keys to select the desired item in the sub menu and then press or key to view further
settings. Adjust the settings by using keys.
Select the next item to be adjusted in the sub menu and adjust as described above.4.
Press the 5. or to conrm, and the screen will return to the main menu.
To exit, press the 6. or again. The OSD menu will close and the projector will automatically save
the new settings.
Sub Menu
Main Menu
Settings
Navigation guide
Display
Image Settings
3D
Aspect Ratio
Edge Mask
Zoom
Image Shift
Keystone
Select Exit Enter
English
22
USING THE PROJECTOR
OSD Menu tree
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Display Image Settings
Display Mode
[Data]
Presentation
Bright
Cinema
Game
sRGB
DICOM
USER
3D
Wall Color [Data]
Off [Default]
BlackBoard
Light Yellow
Light Green
Light Blue
Pink
Gray
Brightness -50~50
Contrast
-50~50
Sharpness 1~15
Color -50~50
Tint -50~50
Gamma
Film
Video
Graphics
Standard(2.2)
1.8
2.0
2.4
Color Settings
BrilliantColor
TM
1~10
Color
Temperature
[Data model]
Warm
medium
Cool
English
23
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Display Image Settings Color Settings
Color Matching
Color
R [Default]
G
B
C
Y
M
W
Saturation -50~50 [Default:0]
Hue -50~50 [Default:0]
Gain -50~50 [Default:0]
Reset
Cancel [Default]
Yes
Exit
RGB Gain/Bias
Red Gain -50~50
Green Gain -50~50
Blue Gain -50~50
Red Bias -50~50
Green Bias -50~50
Blue Bias -50~50
Reset
Cancel [Default]
Yes
Exit
Color Space [Not
HDMI Input]
Auto [Default]
RGB
YUV
Color Space
[HDMI Input]
Auto [Default]
RGB(0~255)
RGB(16~235)
YUV
RGB Channel
Normal [Default]
Red
Green
Blue
White Level -50~50
Black Level -50~50
Saturation -50~50
Hue -50~50
IRE
0
7.5
Exit
English
24
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Display
Image Settings
Signal
Automatic
Off
On [Default]
Frequency 0~100 [Default: 0]
Phase -50~50 [Default: 0]
H. Position -50~50 [Default: 0]
V. Position -50~50 [Default: 0]
Exit
Brightness Mode
[Lamp Base -
Data]
Bright [Default]
Eco
Dynamic
Eco+
Reset
3D
3D Mode
Off
DLP-Link [Default]
IR
3D->2D
3D [Default]
L
R
3D Format
Auto [Default]
SBS
Top and Bottom
Frame Sequential
3D sync invert
On
Off [Default]
Aspect Ratio
4:3
16:9
16:10 [WXGA WUXGA models]
LBX [except SVGA XGA models]
Native
Auto
Edge Mask 0~10 [Default: 0]
Zoom -5~25 [Default: 0]
Image shift
H: 0; V: -100
[Default:0]
H: -100; V: 0
H: 100; V: 0
H: 0; V: 100
H: -100; V: 0
H: 0; V: -100
H: 100; V: 0
H: 0; V: 100
Keystone -40~40 [Default:0]
English
25
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Audio
Mute
Off [Default]
On
Volume 0-10 [Default: 5]
Setup
Projection
Front [Default]
Rear
Ceiling-top
Rear-top
Screen Type
[WXGA WUXGA
models]
16:9
16:10 [Default]
Lamp Settings
Lamp Reminder
Off
On [Default]
Lamp Reset
Cancel [Default]
Yes
Filter Settings
Optional Filter
Installed
Yes
No
Filter Usage
Hours
(Read only)
Filter Reminder
Off
300hr
500hr [Default]
800hr
1000hr
Filter Reset
Cancel [Default]
Yes
Power Settings
Direct Power On
Off [Default]
On
Auto Power Off
(min)
0~180 (5 min increments)
[Default: 0]
Sleep Timer
Sleep Timer
(min)
0~990 (30 min increments)
[Default: 0]
Always On
Yes
No [Default]
Quick Resume
Off
On [Default]
Power Mode
(Standby)
Active
Eco [Default]
Security
Security
Security Timer
Month
Day
Hour
Change
Password
English
26
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Setup
Test Pattern
Off
Grid
White
Remote
Settings
[depends on
remote]
IR Function
On
Off
User1
HDMI 2
Test Pattern
Brightness
Contrast
Sleep Timer
Color Matching
Color Temp
Gamma
Projection
Lamp Settings
Zoom
Freeze
MHL
User2
HDMI 2
Test Pattern
Brightness
Contrast
Sleep Timer
Color Matching
Color Temp
Gamma
Projection
Lamp Settings
Zoom
Freeze
MHL
English
27
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Setup
Remote
Settings
[depends on
remote]
User3
HDMI 2
Test Pattern
Brightness
Contrast
Sleep Timer
Color Matching
Color Temp
Gamma
Projection
Lamp Settings
Zoom
Freeze
MHL
Projector ID 00~99
Options
Language
English [Default]
Deutsch
Français
Italiano
Español
Português
Polski
Nederlands
Svenska
Norsk
Dansk
Suomi
ελληνικά
繁體中文
简体中文
日本
한국어
Русский
Magyar
Čeština
ไทย
Türkçe
Tiếng Việt
Bahasa Indonesia
Română
Slovenčina
Closed
Captioning
CC1
CC2
Off [Default]
English
28
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Setup Options
Menu Settings
Menu Location
Top left
Top right
Center [Default]
Bottom left
Bottom right
Menu Timer
Off
5sec
10sec [Default]
Input Source
HDMI (Type 3 SVGA/ Type 4
XGA/ Type 5 WXGA/ Type 7
1080p)
HDMI1 (Type 2 SVGA/ Type 6
WXGA)
HDMI2/MHL (Type 2 SVGA/ Type
6 WXGA)
VGA (Type 1 SVGA/ Type 3
SVGA/ Type 4 XGA/ Type 5
WXGA/ Type 6 WXGA/ Type 7
1080p)
Video (Type 1 SVGA/ Type 3
SVGA/ Type 4 XGA/ Type 5
WXGA/ Type 6 WXGA/ Type 7
1080p)
Input Name
HDMI
Default (Type 3 SVGA/ Type 4
XGA/ Type 5 WXGA/ Type 7
1080p) [Default]
Custom (Type 3 SVGA/ Type
4 XGA/ Type 5 WXGA/ Type 7
1080p)
HDMI1
Default (Type 2 SVGA/ Type 6
WXGA) [Default]
Custom (Type 2 SVGA/ Type 6
WXGA)
HDMI2/MHL
Default (Type 2 SVGA/ Type 6
WXGA) [Default]
Custom (Type 2 SVGA/ Type 6
WXGA)
VGA
Default (Type 1 SVGA/ Type
3 SVGA/ Type 4 XGA/ Type 5
WXGA/ Type 6 WXGA/ Type 7
1080p) [Default]
Custom (Type 1 SVGA/ Type
3 SVGA/ Type 4 XGA/ Type 5
WXGA/ Type 6 WXGA/ Type 7
1080p)
Video
Default (Type 1 SVGA/ Type
3 SVGA/ Type 4 XGA/ Type 5
WXGA/ Type 6 WXGA/ Type 7
1080p) [Default]
Custom (Type 1 SVGA/ Type
3 SVGA/ Type 4 XGA/ Type 5
WXGA/ Type 6 WXGA/ Type 7
1080p)
English
29
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Setup
Options
High Altitude
Off [Default]
On
Display Mode
Lock
Off [Default]
On
Keypad Lock
Off [Default]
On
Information Hide
Off [Default]
On
Logo
Default [Default]
Neutral
Background
Color
None [Default]
Blue
Red
Green
Grey
Logo
Reset
Reset OSD
Cancel [Default]
Yes
Reset to Default
Cancel [Default]
Yes
Information
Regulatory
Serial Number
Current Input
Source
Resolution 00x00
Refresh Rate 0.00Hz
Projector ID 00~99
Display Mode
Power
mode(standby)
Brightness
Mode
Filter Hours
Lamp Hours
Bright mode 0H
Eco mode 0H
Dynamic mode 0H
Eco+ mode 0H
Total hours
FW Version
System
MCU
Note:
If the Signal setting is set to Automatic, the Phase, frequency items are grayed out. If the “Signal”
setting is set to a specic input source, the phase, frequency items will appear for user to manually
tune and saved in settings.
The “LAMP RESET” in OSD will only reset both Lamp Hours in OSD and Lamp Hours in service
English
30
USING THE PROJECTOR
mode. The Projection Hours in service mode will not be reset.
When you made the changes on the “IR Function”, “Projection”, or “Keypad Lock” function, a
conrmation message will appear on the screen. Select “Yes” to save the settings.
Each display mode can be adjusted and saved the value.
In 3D timing mode, the zoom/edge mask will be disabled to prevent from image break.
Display menu
English
31
USING THE PROJECTOR
Display image settings menu
Display Mode
There are many factory presets optimized for various types of images.
Presentation : This mode is suitable for showing PowerPoint presentations when the projector is
connected to the PC.
Bright : Maximum brightness from PC input.
Cinema : Select this mode for home theater.
Game : Select this mode to increase the brightness and response time level for enjoying video games.
sRGB : Standardized accurate color.
DICOM : This mode can project a monochrome medical image such as an X ray radiography, MRI, etc.
USER : Memorize user’s settings.
3D : To experience the 3D effect, you need to have 3D glasses. Make sure your PC/portable device
has a 120 Hz signal output quad buffered graphics card and a 3D Player installed.
Wall Color (Data mode)
Use this function to obtain an optimized screen image according to the wall color. Select between off, blackboard,
light yellow, light green, light blue, pink, and gray.
Brightness
Adjust the brightness of the image.
Contrast
The contrast controls the degree of difference between the lightest and darkest parts of the picture.
Sharpness
Adjust the sharpness of the image.
Color
Adjust a video image from black and white to fully saturated color.
Tint
Adjust the color balance of red and green.
Gamma
Set up gamma curve type. After the initial setup and ne tuning is completed, utilize the Gamma Adjustment steps
to optimize your image output.
Film : For home theater.
Video : For video or TV source.
Graphics : For PC / Photo source.
Standard(2.2) : For standardized setting.
1.8/ 2.0/ 2.4 : For specic PC / Photo source.
Color Settings
Congure the color settings.
English
32
USING THE PROJECTOR
BrillianColor
TM
: This adjustable item utilizes a new color-processing algorithm and enhancements to
enable higher brightness while providing true, more vibrant colors in picture.
Color Temperature (data-mode only) : Select a color temperature from Warm, Medium, or Cool.
Color Temperature : Select a color temperature from D50, D65, D75, D83, D93, and Native.
Color Matching : Select the following options:
Color: Adjust the red (R), green (G), black (B), cyan (C), yellow (Y), magenta (M), and white (W) ±
level of the image.
Saturation: Adjust a video image from black and white to fully saturated color. ±
Hue: Adjust the color balance of red and green. ±
Gain: Adjust the image brightness. ±
Reset: Return the factory default settings for color matching. ±
Exit: Exit the “Color Matching” menu. ±
RGB Gain/Bias: This settings allows to congure the brightness (gain) and contrast (bias) of an
image.
Reset: Return the factory default settings for RGB gain/bias. ±
Exit: Exit the “RGB Gain/Bias” menu. ±
Color Space (non-HDMI input only) : Select an appropriate color matrix type from the following:
AUTO, RGB, or YUV.
Color Space (HDMI input only) : select an appropriate color matrix type from the following: Auto,
RGB(0-255), RGB(16-235), and YUV.
RGB Channel: Select from normal, red, green, or blue channels.
White Level: Allow user to adjust White Level when inputting Video signals.
Black Level: Allow user to adjust Black Level when inputting Video signals.
Saturation: Adjust a video image from black and white to fully saturated color.
Hue: Adjust the color balance of red and green.
IRE: Allow user to adjust IRE value when inputting Video signals.
IRE is only available with NTSC video format.Note:
Exit : Exit the “Color Settings” menu.
Signal
Adjust the signal options.
Automatic : Congure automatically the signal (the frequency and phase items are grayed out). If
automatic is disabled, the frequency and phase items will appear for tuning and saving the settings.
Frequency : Change the display data frequency to match the frequency of your computer’s graphic
card. Use this function only if the image appears to icker vertically.
Phase : Synchronize the signal timing of the display with the graphic card. If the image appears to be
unstable or ickers, use this function to correct it.
H. Position : Adjust the horizontal positioning of the image.
V. Position : Adjust the vertical positioning of the image.
Exit : Exit the “Signal” menu.
Brightness Mode (Lamp base data)
Adjust the brightness mode settings for lamp-based projectors.
English
33
USING THE PROJECTOR
Bright : Choose “Bright” to increase the brightness.
Eco : Choose “Eco” to dim the projector lamp which will lower power consumption and extend the lamp
life.
Dynamic : Choose “Dynamic” to dim the lamp power which will be based on brightness level of the
content and adjust lamp power consumption between 100% and 30% dynamically. The lamp life will
be extended.
Eco+ : When Eco+ mode is activated, the brightness level of the content is automatically detected to
signicantly reduced lamp power consumption (up to 70%) during periods of inactivity.
Reset
Return the factory default settings for color settings.
Display 3D menu
3D Mode
Use this option to disable the 3D function or select the appropriate the 3D function.
Off : Select “Off” to turn off 3D mode.
DLP-Link : Select to use optimized settings for DLP 3D Glasses.
IR : Select “IR” to use optimized setting for IR 3D Glasses.
3D → 2D
Use this option to specify how the 3D content should appear on the screen.
3D: Display 3D signal.
L (Left): Display the left frame of 3D content.
R (Right): Display the right frame of 3D content.
3D Format
Use this option to select the appropriate 3D format content.
Auto : When a 3D identication signal is detected, the 3D format is selected automatically.
SBS : Display 3D signal in “Side-by-Side” format.
Top and Bottom : Display 3D signal in “Top and Bottom” format.
Frame Sequential : Display 3D signal in “Frame Sequential” format.
3D Sync Invert
Use this option to enable/disable the 3D sync invert function.
English
34
USING THE PROJECTOR
Display aspect ratio menu
Aspect Ratio
Select the aspect ratio of the displayed image between the following options:
4:3 : This format is for 4:3 input sources.
16:9 : This format is for 16:9 input sources, like HDTV and DVD enhanced for Wide screen TV.
16:10 (for WXGA and WUXGA models only) : This format is for 16:10 input sources, like widescreen
laptops.
LBX (except SVGA and XGA models) : This format is for non-16x9, letterbox source and if you use
external 16x9 lens to display 2.35:1 aspect ratio in full resolution.
Native : This format displays the original image without any scaling.
Auto : Automatically selects the appropriate display format.
Note:
Detailed informations about LBX mode:
Some Letter-Box Format DVDs are not enhanced for 16x9 TVs. In this situation, the image ±
will not look right when displaying image in 16:9 mode. In this situation, please try to use the
4:3 mode to view the DVD. If the content is not 4:3, there will be black bars around the image
in 16:9 display. For this type of content, you can use LBX mode to ll the image on the 16:9
display.
If you use an external anamorphic lens, this LBX mode also allows you to watch a 2.35:1 ±
content (include Anamorphic DVD and HDTV lm source) that supports anamorphic wide is
enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Lamp
power and vertical resolution are fully utilized.
To use the superwide format, do the following:
Set the screen aspect ratio to 2.0:1.a)
Select “Superwide” format.b)
Align the projector image correctly on the screen.c)
SVGA/XGA scaling table:
Source 480i/p 576i/p 1080i/p 720p
4x3 Scale to 1024x768.
16x9 Scale to 1024x576.
Native No scaling will be made; the image is displayed with the resolution based on input source.
Auto -If source is 4:3, the screen type will be scaled to 1024x768.
-If source is 16:9, the screen type will be scaled to 1024x576.
-If source is 15:9, the screen type will be scaled to 1024x614.
-If source is 16:10, the screen type will be scaled to 1024x640.
English
35
USING THE PROJECTOR
SVGA/XGA auto mapping rule:
Auto
Input resolution Auto/Scale
H-resolution V-resolution 1024 768
4:3
640 480 1024 768
800 600 1024 768
1024 768 1024 768
1600 1200 1024 768
Wide Laptop
1280 720 1024 576
1280 768 1024 614
1280 800 1024 640
SDTV
720 576 1024 576
720 480 1024 576
HDTV
1280 720 1024 576
1920 1080 1024 576
WXGA scaling table (screen type 16x10):
Note:
Supported screen type 16:9 (1280x720), 16:10 (1280x800).
When screen type is 16:9, the16x10 format becomes unavailable.
When screen type is 16:10, the 16x9 format becomes unavailable.
If you select auto option then the display mode will be also automatically changed.
16 : 10 screen 480i/p 576i/p 1080i/p 720p PC
4x3 Scale to 1066x800.
16x10 Scale to 1280x800.
LBX Scale to 1280x960, then get the central 1280x800 image to display.
Native mode 1:1 mapping centered. 1:1 mapping
display
1280x800.
1280x720
centered.
1:1 mapping
centered.
Auto -Input source will be t into 1280x800 display area and be kept its original aspect ratio.
-If source is 4:3, the screen type will be scaled to 1066x800.
-If source is 16:9, the screen type will be scaled to 1280x720.
-If source is 15:9, the screen type will be scaled to 1280x768.
-If source is 16:10, the screen type will be scaled to 1280x800.
English
36
USING THE PROJECTOR
WXGA auto mapping rule (screen type 16x10):
Auto
Input resolution Auto/Scale
H-resolution V-resolution 1280 800
4:3
640 480 1066 800
800 600 1066 800
1024 768 1066 800
1280 1024 1066 800
1400 1050 1066 800
1600 1200 1066 800
Wide Laptop
1280 720 1280 720
1280 768 1280 768
1280 800 1280 800
SDTV
720 576 1280 720
720 480 1280 720
HDTV
1280 720 1280 720
1920 1080 1280 720
WXGA scaling table (screen type 16x9):
16 : 9 screen 480i/p 576i/p 1080i/p 720p PC
4x3 Scale to 960x720.
16x9 Scale to 1280x720.
LBX Scale to 1280x960, then get the central 1280x720 image to display.
Native mode 1:1 mapping centered. 1:1 mapping
display
1280x720.
1280x720
centered.
1:1 mapping
centred.
Auto -If this format is select, screen type will automatically become 16:9 (1280x720).
-If source is 4:3, the screen type will be scaled to 960x720.
-If source is 16:9, the screen type will be scaled to 1280x720.
-If source is 15:9, the screen type will be scaled to 1200x720.
-If source is 16:10, the screen type will be scaled to 1152x720.
English
37
USING THE PROJECTOR
WXGA auto mapping rule (screen type 16x9):
Auto
Input resolution Auto/Scale
H-resolution V-resolution 1280 720
4:3
640 480 960 720
800 600 960 720
1024 768 960 720
1280 1024 960 720
1400 1050 960 720
1600 1200 960 720
Wide Laptop
1280 720 1280 720
1280 768 1200 720
1280 800 1152 720
SDTV
720 576 1280 720
720 480 1280 720
HDTV
1280 720 1280 720
1920 1080 1280 720
Display edge mask menu
Edge Mask
Use this function to remove the video encoding noise on the edge of video source.
Display zoom menu
Zoom
Use to reduce or magnify an image on the projection screen.
Display image shift menu
Image Shift
Adjust the projected image position horizontally (H) or vertically (V).
Display keystone menu
Keystone
Adjust the image distortion caused by tilting the projector.
English
38
USING THE PROJECTOR
Audio menu
Audio mute menu
Mute
Use this option to temporarily turn off the sound.
On: Choose the “On” to turn mute on.
Off: Choose the “Off” to turn mute off.
“Mute” function affects both internal and external speaker volume.Note:
Audio volume menu
Volume
Adjust the volume level.
Setup menu
Setup projection menu
Projection
Select the preferred projection between front, rear, ceiling-top, and rear-top.
Setup screen type menu
Screen Type (for WXGA and WUXGA models only)
Choose the screen type from 16:9 and 16:10.
Setup lamp settings menu
Lamp Reminder
Choose this function to show or to hide the warning message when the changing lamp message is displayed. The
message will appear 30 hours before suggested replacement of lamp.
Lamp Reset
Resets the lamp hour counter after replacing the lamp.
Setup lter settings menu
Optional Filter Installed
Set the warning message setting.
Yes: Display warning message after 500 hours of use.
“Filter Usage Hours / Filter Reminder / Filter Reset” will only appear when “Optional Filter Installed” is “Yes”.Note:
No: Turn off warning message.
Filter Usage Hours
Display the lter time.
English
39
USING THE PROJECTOR
Filter Reminder
Choose this function to show or hide the warning message when the changing lter message is displayed. The
available options include 300hr, 500hr, 800hr, and 1000hr.
Filter Reset
Reset the dust lter counter after replacing or cleaning the dust lter.
Setup power settings menu
Direct Power On
Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied,
without pressing the “Power” key on the projector keypad or on the remote control.
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the
projector. The projector will automatically power off when the countdown has nished (in minutes).
Sleep Timer
Congure the sleep timer.
Sleep Timer (min): Sets the countdown timer interval. The countdown timer will start, with or without
a signal being sent to the projector. The projector will automatically power off when the countdown has
nished (in minutes).
The Sleep Timer is reset every time when the projector is powered off.Note:
Always On: Check to set the sleep timer always on.
Quick Resume
Set the quick resume setting.
On: If the projector is accidentally turned off, this feature allows the projector to be instantly powered
on again, if selected within a period of 100 seconds.
Off: The fan will start cooling the system after 10 seconds when user turns off the projector.
Power Mode (Standby)
Set the power mode setting.
Active: Choose “Active” to return to normal standby.
Eco.: Choose “Eco.” to save power dissipation further < 0.5W.
English
40
USING THE PROJECTOR
Setup security menu
Security
Enable this function to prompt for a password before using the projector.
On: Choose “On” to use security verication when the turning on the projector.
Off: Choose “Off” to be able to switch on the projector without password verication.
Security Timer
Can be select the time (Month/Day/Hour) function to set the number of hours the projector can be used. Once this
time has elapsed you will be requested to enter your password again.
Change Password
Use to set or modify the password that is prompted when turning the projector on.
English
41
USING THE PROJECTOR
Setup test pattern menu
Test Pattern
Select the test pattern from grid, white or disable this function (off).
Setup remote settings menu
IR Function
Set the IR function setting.
On: Choose “On”, the projector can be operated by the remote control from front or top IR receiver.
Off: Choose “Off”, the projector can’t be operated by the remote control from front or top IR receiver.
By selecting “Off”, you will be able to use the Keypad keys.
Remote Code
Set remote custom code.
User1/ User2/ User3
Assign the default function for User1, User2, or User3 between HDMI 2, test pattern, brightness, contrast, sleep
timer, color matching, color temp, gamma, projection, lamp settings, zoom, freeze, and MHL.
Setup projector ID menu
Projector ID
ID denition can be set up by menu (range 0-99), and allow user control an individual projector by using RS232 command.
Setup options menu
Language
Select the multilingual OSD menu between English, German, French, Italian, Spanish, Portuguese, Polish, Dutch,
Swedish, Norwegian/Danish, Finnish, Greek, traditional Chinese, simplied Chinese, Japanese, Korean, Russian,
Hungarian, Czechoslovak, Arabic, Thai, Turkish, Farsi, Vietnamese, Indonesian, Romanian, and Slovakian.
Closed Captioning
Closed Captioning is a text version of the program sound or other information displayed on the screen. If the input
signal contains closed captions, you can turn on the feature and watch the channels. The available options include
“Off”, “CC1”, and “CC2”.
Menu Settings
Set the menu location on the screen and congure menu timer settings.
Menu Location : Select the menu location on the display screen.
Menu Timer : Set the duration where the OSD menu stays visible on the screen.
Input Source
Select the input source between HDMI (Type 3 SVGA/ Type 4 XGA/ Type 5 WXGA/ Type 7 1080p), HDMI1
(Type 2 SVGA/ Type 6 WXGA), HDMI2/MHL (Type 2 SVGA/ Type 6 WXGA), VGA (Type 1 SVGA/ Type 3
SVGA/ Type 4 XGA/ Type 5 WXGA/ Type 6 WXGA/ Type 7 1080p), video (Type 1 SVGA/ Type 3 SVGA/ Type 4
XGA/ Type 5 WXGA/ Type 6 WXGA/ Type 7 1080p).
Input Name
Use to rename the input function for easier identication. The available options include HDMI (Type 3 SVGA/
Type 4 XGA/ Type 5 WXGA/ Type 7 1080p), HDMI1 (Type 2 SVGA/ Type 6 WXGA), HDMI2/MHL (Type 2
SVGA/ Type 6 WXGA), VGA (Type 1 SVGA/ Type 3 SVGA/ Type 4 XGA/ Type 5 WXGA/ Type 6 WXGA/ Type 7
1080p), video (Type 1 SVGA/ Type 3 SVGA/ Type 4 XGA/ Type 5 WXGA/ Type 6 WXGA/ Type 7 1080p).
English
42
USING THE PROJECTOR
High Altitude
When “On” is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin.
Display Mode Lock
Choose “On” or “Off” to lock or unlock adjusting display mode settings.
Keypad Lock
When the keypad lock function is “On”, the Keypad will be locked. However, the projector can be operated by the
remote control. By selecting “Off”, you will be able to reuse the Keypad.
Information Hide
Enable this function to hide the information message.
On: Choose “On” to hide the info message.
Off: Choose “Off” to show the “searching” message.
Logo
Use this function to set the desired startup screen. If changes are made, they will take effect the next time the
projector is powered on.
Default: The default startup screen.
Neutral: Logo is not displayed on startup screen.
Background Color
Use this function to display a blue, red, green, grey color, none, or logo screen when no signal is available.
Setup reset all menu
Reset
Return the factory default settings for Setup menu settings.
Info menu
Info menu
View the projector information as listed below:
Regulatory
Serial Number
Current Input Source
Resolution
Refresh Rate
Projector ID
Display Mode
Power mode(standby)
Brightness Mode
Filter Hours
Lamp Hours
FW Version
English
43
MAINTENANCE
Replacing the lamp
The projector automatically detects the lamp life. When the lamp life is nearing the end of use, a warning message
will appear on the screen.
Warning
Lamp Warning
Lamp life exceeded.
When you see this message, please contact your local reseller or service center to change the lamp as soon as
possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.
Warning: If ceiling mounted, please use caution when opening the lamp access panel. It is
recommended to wear safety glasses if changing the bulb when ceiling mounted. Caution must be used
to prevent any loose parts from falling out of projector.
Warning: Lamp compartment is hot! Allow it to cool down before changing lamp!
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The
bulb may shatter and cause injury if it is dropped.
English
44
MAINTENANCE
Replacing the lamp (continued)
3
1
2
6
5
4
Procedure:
Switch off the power to the projector by pressing the "1. " button on the remote control or the projector
keypad.
Allow the projector to cool down for at least 30 minutes.2.
Disconnect the power cord.3.
Unscrew the screw on the cover. 4. 1
Remove the cover. 5. 2
Unscrew the screw on the lamp module. 6. 3
Lift up the lamp handle. 7. 4
Remove the lamp cord. 8. 5
Remove the lamp module carefully. 9. 6
To replace the lamp module, reverse the previous steps.10.
Turn on the projector and reset the lamp timer.11.
Lamp Reset: (i) Press "Menu" 12. (ii) Select "Setup" (iii) Select "Lamp Settings"
(iv) Select "Lamp
Reset"
(v) Select "Yes".
Note:
The screw on the lamp cover and the lamp cannot be removed.
The projector cannot be turned on if the lamp cover has not been placed back on the projector.
Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean
the lamp module if it was accidentally touched.
English
45
MAINTENANCE
Installing and cleaning the dust lter
Installing the dust lter
Dust lters are only required/supplied in the selected regions with excessive dust.Note:
Cleaning the dust lter
We recommend you to clean the dust lter every three months. Clean it more often if the projector is used in a
dusty environment.
Procedure:
Switch off the power to the projector by pressing 1. the " " button on the remote control or the projector
keypad.
Disconnect the power cord.2.
Remove the dust lter carefully3. . 1
Clean or replace the dust lter4. . 2
To install the dust lter, reverse the previous steps.5.
1
2
English
46
ADDITIONAL INFORMATION
Compatible resolutions
Digital compatibility
B0/Established
Timing
B0/Standard Timing B0/Detail Timing B1/Video Mode B1/Detail Timing
720x400 @ 70Hz SVGA: Native timing: 640x80p @ 60Hz 720x480p @ 60Hz
640x480 @ 60Hz 800x600 @ 120Hz XGA: 1024x768 @ 60Hz 720x480p @ 60Hz 1280x720p @ 60Hz
640x480 @ 67Hz 1024x768 @ 120Hz WXGA: 1280x800 @ 60Hz;
1280x720 @ 60Hz
1280x720p @ 60Hz 1366x768 @ 60Hz
640x480 @ 72Hz 1280x800 @ 60Hz 1080P: 1920x1080 @ 60Hz 1920x1080i @ 60Hz 1920x1080i @ 50Hz
640x480 @ 75Hz 1280x1024 @ 60Hz 720(1440)x480i @ 60Hz 1920x1080p @ 60Hz
800x600 @ 56Hz 1680x1050 @ 60Hz 1920x1080p @ 60Hz
800x600 @ 60Hz 1280x720 @ 60Hz 720x576p @ 50Hz
800x600 @ 72Hz 1280x720 @ 120Hz 1280x720p @ 50Hz
800x600 @ 75Hz 1600x1200 @ 60Hz 1920x1080i @ 50Hz
832x624 @ 75Hz XGA/WXGA: 720(1440)x576i @ 50Hz
1024x768 @ 60Hz 1440x900 @ 60Hz 1920x1080p @ 50Hz
1024x768 @ 70Hz 1024x768 @ 120Hz 1920x1080p @ 24Hz
1024x768 @ 75Hz 1280x800 @ 60Hz 1920x1080p @ 30Hz
1280x1024 @ 75Hz 1280x1024 @ 60Hz
1152x870 @ 75Hz 1680x1050 @ 60Hz
1280x720 @ 60Hz
1280x720 @ 120Hz
1600x1200 @ 60Hz
1080P:
1280x720 @ 60Hz
1280x800 @ 60Hz
1280x1024 @ 60Hz
1400x1050 @ 60Hz
1600x1200 @ 60Hz
1440x900 @ 60Hz
1280x720 @ 120Hz
1024x768 @ 120Hz
English
47
ADDITIONAL INFORMATION
Analog compatibility
B0/Established
Timing
B0/Standard Timing B0/Detail Timing B1/Video Mode B1/Detail Timing
720x400 @ 70Hz SVGA: Native timing: 1366x768 @ 60Hz
640x480 @ 60Hz 800x600 @ 120Hz XGA: 1024x768 @ 60Hz
640x480 @ 67Hz 1024x768 @ 120Hz WXGA: 1280x800 @ 60Hz;
1280x720 @ 60Hz
640x480 @ 72Hz 1280x800 @ 60Hz 1080P: 1920x1080 @ 60Hz
640x480 @ 75Hz 1280x1024 @ 60Hz
800x600 @ 56Hz 1680x1050 @ 60Hz
800x600 @ 60Hz 1280x720 @ 60Hz
800x600 @ 72Hz 1280x720 @ 120Hz
800x600 @ 75Hz 1600x1200 @ 60Hz
832x624 @ 75Hz XGA/WXGA:
1024x768 @ 60Hz 1440x900 @ 60Hz
1024x768 @ 70Hz 1024x768 @ 120Hz
1024x768 @ 75Hz 1280x800 @ 60Hz
1280x1024 @ 75Hz 1280x1024 @ 60Hz
1152x870 @ 75Hz 1680x1050 @ 60Hz
1280x720 @ 60Hz
1280x720 @ 120Hz
1600x1200 @ 60Hz
1080P:
1280x720 @ 60Hz
1280x800 @ 60Hz
1280x1024 @ 60Hz
1400x1050 @ 60Hz
1600x1200 @ 60Hz
1440x900 @ 60Hz
1280x720 @ 120Hz
1024x768 @ 120Hz
English
48
ADDITIONAL INFORMATION
True 3D video compatibility
Input resolution
HDMI 1.4a 3D
Input
Input timing
1280x720P @ 50Hz Top - and - Bottom
1280x720P @ 60Hz Top - and - Bottom
1280x720P @ 50Hz Frame packing
1280x720P @ 60Hz Frame packing
1920x1080i @ 50 Hz Side- by-Side (Half)
1920x1080i @ 60 Hz Side- by-Side (Half)
1920x1080P @ 24 Hz Top - and- Bottom
1920x1080P @ 24 Hz Frame packing
HDMI 1.3
1920x1080i @ 50Hz
Side-by-Side(Half) SBS mode is on
1920x1080i @ 60Hz
1280x720P @ 50Hz
1280x720P @ 60Hz
800 x 600 @ 60Hz
1024 x 768 @ 60Hz
1280 x 800 @ 60Hz
1920x1080i @ 50Hz
Top-and-Bottom TAB mode is on
1920x1080i @ 60Hz
1280x720P @ 50Hz
1280x720P @ 60Hz
800x600 @ 60Hz
1024x768 @ 60Hz
1280x800 @ 60Hz
480i HQFS 3D format is Frame sequential
Note:
If 3D input is 1080p@24hz, the DMD should replay with integral multiple with 3D mode.
Support NVIDIA 3DTV Play if there is no patent fee from Optoma. 1080i@25hz and 720p@50hz will
run in 100 hz; other 3D timing will run in 120hz.
1080p@24hz will run in 144Hz.
English
49
ADDITIONAL INFORMATION
Image size and projection distance
(1080P)
Diagonal
Length
Size of
(16:9)
Screen
Screen Size W x H Projection Distance (D)
Offset
(m) (inch) (m) (inch)
Width Height Width Height Wide Tele Wide Tele (m) (inch)
36 0.80 0.45 31.38 17.65 1.2 1.3 3.94 4.27 0.07 2.76
40 0.89 0.5 34.86 19.6 1.3 1.4 4.27 4.59 0.08 3.15
50 1.11 0.62 43.58 24.5 1.6 1.8 5.25 5.91 0.10 3.94
60 1.33 0.75 52.29 29.4 2.0 2.2 6.56 7.22 0.12 4.72
70 1.55 0.87 61.01 34.3 2.3 2.5 7.55 8.20 0.14 5.51
80 1.77 1 69.73 39.2 2.6 2.9 8.53 9.51 0.16 6.30
90 1.99 1.12 78.44 44.1 2.9 3.2 9.51 10.50 0.18 7.09
100 2.21 1.25 87.16 49 3.3 3.6 10.83 11.81 0.19 7.48
120 2.66 1.49 104.59 58.8 3.9 4.3 12.80 14.11 0.24 9.45
150 3.32 1.87 130.74 73.5 4.9 5.4 16.08 17.72 0.30 11.81
180 3.98 2.24 156.88 88.2 5.9 6.5 19.36 21.33 0.36 14.17
200 4.43 2.49 174.32 98.1 6.6 7.2 21.65 23.62 0.40 15.75
250 5.53 3.11 217.89 122.6 8.2 9.0 26.90 29.53 0.50 19.69
300 6.64 3.74 261.47 147.1 9.8 10.8 32.15 35.43 0.59 23.23
Zoom ratio is 1.1x.Note:
Gewicht
Hoogte
Diagonale
Bovenaanzicht
Zijaanzicht
Projectie-afstand (D)
Projectie-afstand (D)
Beeldscherm
Beeldscherm
Scherm (B)
Scherm (H)
Verschuiving (Hd)
English
50
ADDITIONAL INFORMATION
Projector dimensions and ceiling mount installation
To prevent damage to your projector, please use the Optoma ceiling mount.1.
If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to 2.
the projector meet the following specications:
Screw type: M4*3
Minimum screw length: 10mm
297,99
55,00
110,00
82,30 90,10
83,00
96,50
Unit: mm
Lens
Please note that damage resulting from incorrect installation will void the warranty.Note:
Warning:
If you buy a ceiling mount from another company, please be sure to use the correct screw size.
Screw size will vary depending on the thickness of the mounting plate.
Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.
Avoid installing the projector near a heat source.
English
51
ADDITIONAL INFORMATION
IR remote codes
Key legend Description
Repeat
format
Address Data
byte 1 byte 2 byte 3 byte 4
Power
Press to turn on / off the projec-
tor.
F1 32 CD 81 7E
Freeze
Press to freeze the projector
image.
F1 32 CD 87 78
Aspect
Press to change aspect ratio of
a displayed image.
F1 32 CD 98 67
AV mute
Press to turn off/ on projector
built-in speaker
F1 32 CD 8A 75
Keystone+/up
Press to adjust image
distortion caused by tilting
the projector.
Press to navigate up.
F2 32 CD 85 7A
Mute
Press to momentarily turn off /
on the audio.
F1 32 CD 92 6D
Left/Vol-
Press to adjust to
decrease the volume.
Press to navigate left.
F2 32 CD 8F 70
Enter Conrm your item selection. F1 32 CD C5 3A
Right/Vol+
Press to adjust to increase
the volume.
Press to navigate right.
F2 32 CD 8C 73
Menu
Press to display or exit the
on-screen display menus for
projector.
F1 32 CD 88 77
English
52
ADDITIONAL INFORMATION
Key legend Description
Repeat
format
Address Data
byte 1 byte 2 byte 3 byte 4
Down/Key-
stone-
Press to adjust image
distortion caused by tilting
the projector.
Press to navigate down.
F2 32 CD 84 7B
3D
Press to manually select a 3D
mode that matches your 3D
content.
F1 32 CD 93 6C
HDMI Press to choose HDMI source. F1 32 CD 86 79
VGA Press to choose VGA source. F1 32 CD 8E 71
Video Press to choose video source. F1 32 CD CE 72
Source Press to select an input signal. F1 32 CD C3 3C
Lamp mode Press to choose lamp mode. F1 32
CD C0 3F
ReSync
Automatically synchronize the
projector to the input source.
F1 32
CD C4 3B
English
53
ADDITIONAL INFORMATION
Troubleshooting
If you experience a problem with your projector, please refer to the following information. If a problem persists,
please contact your local reseller or service center.
Image problems
No image appears on-screen
Ensure all the cables and power connections are correctly and securely connected as described in the
"Installation" section.
Ensure the pins of connectors are not crooked or broken.
Check if the projection lamp has been securely installed. Please refer to the "Replacing the Lamp"
section.
Ensure that the "AV Mute" feature is not turned on.
Image is out of focus
Adjust the Focus Ring on the projector lens.
Make sure the projection screen is between the required distance from the projector. (Please refer to
page 49).
The image is stretched when displaying 16:9 DVD title
When you play anamorphic DVD or 16:9 DVD, the projector will show the best image in 16: 9 format
on projector side.
If you play the LBX format DVD title, please change the format as LBX in projector OSD.
If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD.
Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player.
Image is too small or too large
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the screen.
Press "Menu" on the projector panel, go to "Display-->Aspect Ratio". Try the different settings.
Image has slanted sides:
If possible, reposition the projector so that it is centered on the screen and below the bottom of the
screen.
Use "Display-->Keystone" from the OSD to make an adjustment.
Image is reversed
Select "Setup-->Projection" from the OSD and adjust the projection direction.
Blurry double image
Press "3D" button and switch to "Off" to avoid normal 2D image is blurry double image.
English
54
ADDITIONAL INFORMATION
Two images, side-by-side format
Press "3D" button and switch to "SBS" for input signal is HDMI 1.3 2D 1080i side-by-side.
Image does not display in 3D
Check if the battery of 3D glasses is drained.
Check if the 3D glasses is turned on.
When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D" button and switch to "SBS".
Other problems
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the "Replacing the Lamp" section on pages 43-44.
Remote control problems
If the remote control does not work
Check the operating angle of the remote control is pointed within ±10° to the IR receiver on the
projector.
Make sure there are not any obstructions between the remote control and the projector. Move to within
7 m (23 ft) of the projector.
Make sure batteries are inserted correctly.
Replace batteries if they are exhausted.
English
55
ADDITIONAL INFORMATION
Warning indicators
When the warning indicators (see below) light up or ash, the projector will automatically shutdown:
"LAMP" LED indicator is lit red and if "On/Standby" indicator ashes amber.
"TEMP" LED indicator is lit red and if "On/Standby" indicator ashes amber. This indicates the
projector has overheated. Under normal conditions, the project can be switched back on.
"TEMP" LED indicator ashes red and if "On/Standby" indicator ashes amber.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or
ash, please contact your nearest service center for assistance.
LED lightning messages
Message
Power LED Power LED
Temp-LED
Lamp-LED
(Red) (Green or Blue) (Red) (Red)
Standby state
(Input power cord)
Steady light
Power on (Warming)
Flashing
(0.5 sec off /
0.5 sec on)
Power on and Lamp
lighting
Steady light
Power off (Cooling)
Flashing
(0.5 sec off /
0.5 sec light). Back
to red steady light
when cooling fan
turns off.
Quick Resume (100
secs)
Flashing
(0.25 sec off /
0.25 sec light)
Error (Over temp.) Flashing
Error (Fan failure) Flashing Flashing
Error (Lamp failure) Flashing
Power off:
Power Off
Power Off?
Press power key again.
Lamp warning:
Warning
Lamp Warning
Lamp life exceeded.
English
56
ADDITIONAL INFORMATION
Temperature warning:
Warning
TEMPERATURE TOO HIGH
Please:
1. Make sure air in and outlets are not blocked.
2. Make sure the environment temperature is under 45 degree C.
If the problem persists in spite of the above.
Please contact a service center for repair.
Fan failed:
Warning
FAN LOCKED
The projector will switch off automatically
Please contact a service center for repair.
Out of display range:
HDMI
Out Of Range
Power down warning:
Power Down
Power Down Timer Active
Power down in sec.
Security timer alarm:
Warning
Security Timer Alarm
Time Out in sec.
English
57
USING THE PROJECTOR
Specications
Optical Description
Maximum resolution UXGA, 1600x1200, 60Hz WUXGA for WXGA 16:10
Native resolution SVGA/XGA/WXGA/1080p
Lens - Manual zoom and manual focus
Lamp life
- Bright Mode (Normal Mode) 5000 Hours Standard @190W, 50% Survival Rate
- STD Mode (ECO Mode) 6000 Hours Typical @160W, 50% Survival Rate
- Dynamic mode 6500 Hours
- DE Mode in education cycle 10000 Hours
Image size (diagonal) 22.9” ~ 252” (overdrive to 300”)
Projection distance 1m ~ 10m (focus range) (overdrive to 12m)
Electrical Description
Inputs
- HDMI 1.4a
- HDMI 1.4a + MHL (v2.2)
- VGA-IN (YPbPr / RGB)
- Audio 3.5mm
Outputs
- VGA
- Audio 3.5mm
- USB-A power
Control
- RS232
- USB mouse / service
Color reproduction 1073.4 Million color
Scan rate
- Horizontal scan rate: 15.375~91.146 KHz
- Vertical scan rate: 24~ 85 Hz (120Hz for 3D feature projector)
Built-in speaker Yes, 10W
Power requirement 100 - 240V AC 50/60Hz
Input current 2.5-1.0 A
Mechanical Description
Installation orientation Front, Rear, Ceiling - Front, Rear - top
Dimensions
- 298 mm (W) x 230 mm (D) x 83 mm (H) (without feet)
- 298 mm (W) x 230 mm (D) x 96.5 mm (H) (with feet)
Weight 2.5 kg
Environmental conditions Operating in 5 ~ 40°C , 10% to 85% humidity (non-condensing)
All specications are subject to change without notice.Note:
English
58
USING THE PROJECTOR
Optoma global ofces
For service or support, please contact your local ofce.
USA
3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com services@optoma.com
Canada
3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com services@optoma.com
Latin America
3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com services@optoma.com
Europe
42 Caxton Way, The Watford Business Park
Watford, Hertfordshire,
WD18 8QZ, UK +44 (0) 1923 691 800
www.optoma.eu +44 (0) 1923 691 888
Service Tel : +44 (0)1923 691865 service@tsc-europe.com
Benelux BV
Randstad 22-123 +31 (0) 36 820 0252
1316 BW Almere +31 (0) 36 548 9052
The Netherlands
www.optoma.nl
France
Bâtiment E +33 1 41 46 12 20
81-83 avenue Edouard Vaillant +33 1 41 46 94 35
92100 Boulogne Billancourt, France savoptoma@optoma.fr
Spain
C/ José Hierro,36 Of. 1C +34 91 499 06 06
28522 Rivas VaciaMadrid, +34 91 670 08 32
Spain
Deutschland
Wiesenstrasse 21 W +49 (0) 211 506 6670
D40549 Düsseldorf, +49 (0) 211 506 66799
Germany info@optoma.de
Scandinavia
Lerpeveien 25 +47 32 98 89 90
3040 Drammen +47 32 98 89 99
Norway info@optoma.no
PO.BOX 9515
3038 Drammen
Norway
Korea
WOOMI TECH.CO.,LTD. +82+2+34430004
4F, Minu Bldg.33-14, Kangnam-Ku, +82+2+34430005
Seoul,135-815, KOREA
korea.optoma.com
Japan
東京都足立区綾瀬3-25-18
株式会社オーエス info@os-worldwide.com
コンタクトセンター:0120-380-495 www.os-worldwide.com
Taiwan
12F., No.213, Sec. 3, Beixin Rd., +886-2-8911-8600
Xindian Dist., New Taipei City 231, +886-2-8911-6550
Taiwan, R.O.C. services@optoma.com.tw
www.optoma.com.tw asia.optoma.com
Hong Kong
Unit A, 27/F Dragon Centre,
79 Wing Hong Street, +852-2396-8968
Cheung Sha Wan, +852-2370-1222
Kowloon, Hong Kong www.optoma.com.hk
China
5F, No. 1205, Kaixuan Rd., +86-21-62947376
Changning District +86-21-62947375
Shanghai, 200052, China www.optoma.com.cn
www.optoma.com
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Optoma EH331 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Optoma EH331 in de taal/talen: Nederlands als bijlage per email.

De handleiding is 11,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Optoma EH331

Optoma EH331 Gebruiksaanwijzing - Nederlands - 59 pagina's

Optoma EH331 Gebruiksaanwijzing - Deutsch - 59 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info