700393
65
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
User manual
DLP
®
Projector
English
2
TABLE OF CONTENTS
SAFETY ............................................................................................... 4
Important Safety Instruction....................................................................................................... 4
3D Safety Information ................................................................................................................ 5
Copyright ................................................................................................................................... 6
Disclaimer .................................................................................................................................. 6
Trademark Recognition ............................................................................................................. 6
FCC ........................................................................................................................................... 7
Declaration of Conformity for EU countries ............................................................................... 7
WEEE ........................................................................................................................................ 7
INTRODUCTION .................................................................................. 8
Package Overview..................................................................................................................... 8
Standard accessories ................................................................................................................ 8
Optional accessories ................................................................................................................. 8
Product Overview ...................................................................................................................... 9
Connections.............................................................................................................................. 10
Keypad ..................................................................................................................................... 11
Remote control ......................................................................................................................... 12
SETUP AND INSTALLATION ............................................................. 13
Installing the projector .............................................................................................................. 13
Connecting sources to the projector ......................................................................................... 16
Adjusting the projector image ................................................................................................... 17
Remote setup ........................................................................................................................... 18
USING THE PROJECTOR .................................................................. 20
Powering on / off the projector.................................................................................................. 20
Selecting an input source ......................................................................................................... 22
Menu navigation and features .................................................................................................. 23
OSD Menu tree......................................................................................................................... 24
Display image settings menu.................................................................................................... 32
Display 3D menu ...................................................................................................................... 35
Display aspect ratio menu ........................................................................................................ 35
Display digital zoom menu........................................................................................................ 37
Display image shift menu ......................................................................................................... 37
Audio internal speaker menu .................................................................................................... 37
Audio audio out menu............................................................................................................... 37
Audio mute menu ..................................................................................................................... 37
Audio volume menu .................................................................................................................. 37
Audio audio input menu ............................................................................................................ 37
Setup projection menu.............................................................................................................. 38
Setup lamp settings menu ........................................................................................................ 38
Setup lter settings menu ......................................................................................................... 38
English
3
Setup power settings menu ...................................................................................................... 38
Setup security menu ................................................................................................................. 39
Setup test pattern menu ........................................................................................................... 39
Setup remote settings menu..................................................................................................... 40
Setup projector ID menu........................................................................................................... 40
Setup 12V trigger menu............................................................................................................ 40
Setup HDBaseT control menu .................................................................................................. 40
Setup options menu.................................................................................................................. 41
Setup reset OSD menu ............................................................................................................ 42
Network LAN menu .................................................................................................................. 42
Network control menu............................................................................................................... 43
Setup network control settings menu ....................................................................................... 44
Info menu.................................................................................................................................. 49
MAINTENANCE .................................................................................. 50
Replacing the lamp ................................................................................................................... 50
Installing and cleaning the dust lter ........................................................................................ 52
ADDITIONAL INFORMATION ............................................................ 53
Compatible resolutions ............................................................................................................. 53
Image size and projection distance .......................................................................................... 55
Projector dimensions and ceiling mount installation ................................................................. 58
IR remote codes ....................................................................................................................... 60
Troubleshooting ........................................................................................................................ 62
Warning indicators .................................................................................................................... 64
Specications ........................................................................................................................... 66
Optoma global ofces ............................................................................................................... 67
English
4
SAFETY
The lightning ash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Please follow all warnings, precautions and maintenance as recommended in this user's guide.
Important Safety Instruction
To prolong the effective life of the lamp, make sure to keep the lamp on for at least 60 seconds and
avoid performing force shutdown.
RG2
Do not stare into the beam, RG2.
As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015.
Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from
over heating, it is recommended to install the projector in a location that does not block ventilation.
As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the
projector in an enclosure such as a book case or a cabinet that restricts air ow.
To reduce the risk of re and/or electric shock, do not expose the projector to rain or moisture. Do not
install near heat sources such as radiators, heaters, stoves or any other apparatus such as ampliers
that emits heat.
Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short
out parts that could result in re or electric shock.
Do not use under the following conditions:
± In extremely hot, cold or humid environments.
(i) Ensure that the ambient room temperature is within 5°C ~ 40°C
(ii) Relative humidity is 10% ~ 85%
± In areas susceptible to excessive dust and dirt.
± Near any appliance generating a strong magnetic eld.
± In direct sunlight.
Do not use the projector in places where ammable gases or explosives gases may be present in the
atmosphere. The lamp inside the projector becomes very hot during operation and the gases may
ignite and result in a re.
Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be
(but not limited to):
± Unit has been dropped.
± Power supply cord or plug has been damaged.
± Liquid has been spilled on to the projector.
± Projector has been exposed to rain or moisture.
± Something has fallen in the projector or something is loose inside.
Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the
projector may become damaged.
English
5
Do not block the light coming out of the projector lens when in operation. The light will heat the object
and my melt, cause burns or start a re.
Please do not open or disassemble the projector as this may cause electric shock.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous
voltages or other hazards. Please call Optoma before you send the unit for repair.
See projector enclosure for safety related markings.
The unit should only be repaired by appropriate service personnel.
Only use attachments/accessories specied by the manufacturer.
Do not look into straight into the projector lens during operation. The bright light may harm your eyes.
When replacing the lamp, please allow the unit to cool down. Follow instructions as described on
pages 50-51.
This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows
warning messages.
Reset the "Lamp Reset" function from the on-screen display "Setup lamp settings" menu after
replacing the lamp module.
When switching the projector off, please ensure the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the projector to cool down.
When the lamp is approaching to the end of its life time, the message "Lamp life exceeded." will show
on the screen. Please contact your local reseller or service center to change the lamp as soon as
possible.
Turn off and unplug the power plug from the AC outlet before cleaning the product.
Use a soft dry cloth with mild detergent to clean the display housing. Do not use abrasive cleaners,
waxes or solvents to clean the unit.
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
Note: When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has been
replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages
50-51.
Do not setup the projector in places where it might be subjected to vibration or shock.
Do not touch the lens with bare hands.
Remove battery/batteries from remote control before storage. If the battery/batteries are left in the
remote for long periods, they may leak.
Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it
can adversely affect the quality of the projector performance.
Please follow the correct projector orientation installation as non standard installation may affect the
projector performance.
Use a power strip and or surge protector. As power outages and brown-outs can KILL devices.
3D Safety Information
Please follow all warnings and precautions as recommended before you or your child use the 3D function.
Warning
Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be
closely supervised when viewing these images.
Photosensitive Seizure Warning and Other Health Risks
Some viewers may experience an epileptic seizure or stroke when exposed to certain ashing images
or lights contained in certain Projector pictures or video games. If you suffer from, or have a family
history of epilepsy or strokes, please consult with a medical specialist before using the 3D function.
Even those without a personal or family history of epilepsy or stroke may have an undiagnosed
condition that can cause photosensitive epileptic seizures.
Pregnant women, the elderly, sufferers of serious medical conditions, those who are sleep deprived or
under the inuence of alcohol should avoid utilizing the unit’s 3D functionality.
English
6
If you experience any of the following symptoms, stop viewing 3D pictures immediately and consult a
medical specialist: (1) altered vision; (2) light-headedness; (3) dizziness; (4) involuntary movements
such as eye or muscle twitching; (5) confusion; (6) nausea; (7) loss of awareness; (8) convulsions;
(9) cramps; and/ or (10) disorientation. Children and teenagers may be more likely than adults
to experience these symptoms. Parents should monitor their children and ask whether they are
experiencing these symptoms.
Watching 3D projection may also cause motion sickness, perceptual after effects, disorientation, eye
strain and decreased postural stability. It is recommended that users take frequent breaks to lessen
the potential of these effects. If your eyes show signs of fatigue or dryness or if you have any of the
above symptoms, immediately discontinue use of this device and do not resume using it for at least
thirty minutes after the symptoms have subsided.
Watching 3D projection while sitting too close to the screen for an extended period of time may
damage your eyesight. The ideal viewing distance should be at least three times the screen height. It
is recommended that the viewers eyes are level with the screen.
Watching 3D projection while wearing 3D glasses for an extended period of time may cause a
headache or fatigue. If you experience a headache, fatigue or dizziness, stop viewing the 3D
projection and rest.
Do not use the 3D glasses for any other purpose than for watching 3D projection.
Wearing the 3D glasses for any other purpose (as general spectacles, sunglasses, protective goggles,
etc.) may be physically harmful to you and may weaken your eyesight.
Viewing in 3D projection may cause disorientation for some viewers. Accordingly, DO NOT place your
3D PROJECTOR near open stairwells, cables, balconies, or other objects that can be tripped over, run
into, knocked down, broken or fallen over.
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright
laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced
without written consent of the author.
© Copyright 2018
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations
or warranties with respect to the contents hereof and specically disclaims any implied warranties of
merchantability or tness for any particular purpose. The manufacturer reserves the right to revise this publication
and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending
applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
DLP
®
, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor
TM
is a
trademark of Texas Instruments.
MHL, Mobile High-Denition Link and the MHL Logo are trademarks or registered trademarks of MHL Licensing,
LLC.
All other product names used in this manual are the properties of their respective owners and are Acknowledged.
English
7
FCC
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be determined by turning the device off and on is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC
regulations.
Caution
Changes or modications not expressly approved by the manufacturer could void the user's authority, which is
granted by the Federal Communications Commission, to operate this projector.
Operation Conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque à l’intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
EMC Directive 2014/30/EC (including amendments)
Low Voltage Directive 2014/35/EC
R & TTE Directive 1999/5/EC (if product has RF function)
WEEE
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure
utmost protection of the global environment, please recycle it.
English
8
INTRODUCTION
Package Overview
Carefully unpack and verify that you have the items listed below under standard accessories. Some of the items
under optional accessories may not be available depending on the model, specication and your region of
purchase. Please check with your place of purchase. Some accessories may vary from region to region.
The warranty card is only supplied in some specic regions. Please consult your dealer for detailed information.
Standard accessories
Optional accessories
Note:
Optional accessories vary depending on model, specication and region.
Optoma recommends the use of Premium Certied HDMI Cables.
Optoma only guarantees operational stability for Premium Certied HDMI Cable lengths up to 5
meters.
Note:
The remote control is shipped with the battery.
* For European warranty Information, please visit www.optoma.com.
Remote control Power leadProjector
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+Laser
Enter
Documentation

Warranty Card*

Basic User Manual
Projector
(For short-throw lens models)
HDMI cable CD user manual
Lens cap
Lens cap
(For short-throw lens models)
English
9
INTRODUCTION
Product Overview
31
8 9
9
5
2 4
11 11
10
4
6
7
31
9
9
5
2 4
11 11
10
4
6
7
For short-throw lens models
Note:
Do not block projector intake and exhaust vents.
When operating the projector in an enclosed space, allow at least 30 cm clearance around the intake
and exhaust vents.
No Item No Item
1. Top Cover 7. Lens Shift Dial
2. Lens 8. Zoom Lever
3. Focus Ring 9. Ventilation (outlet)
4. IR Receiver 10. Keypad
5. Input / Output 11. Tilt-Adjustment Foot
6. Ventilation (inlet)
English
10
INTRODUCTION
Connections
5 7 10
1314
6 9
12
1 2 3 8
11
4
No Item No Item
1. HDBaseT Connector* 8. 12V OUT Connector
2. RJ-45 Connector 9. Service Connector
3. RS232 Connector 10. S/PDIF Connector
4. HDMI 1 Connector 11. USB Power Out (5V 1.5A)
5. HDMI 2 / MHL Connector 12. AUDIO OUT Connector
6. VGA Connector 13. Kensington
TM
Lock Port
7. AUDIO IN Connector 14. Power Socket
Note: (*) On models with HDBaseT only.
English
11
INTRODUCTION
Keypad
1
7
3
4
2
6 5
8
9
No Item No Item
1. Power 6. Lamp LED
2. Enter 7. On/Standby LED
3. Re-Sync 8. Source
4. Menu 9. Four Directional Select Keys
5. Temp LED
English
12
INTRODUCTION
Remote control
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+Laser
Enter
4
1
2
3
5
6
13
10
8
7
9
11
12
14
15
27
20
16
17
18
22
23
24
21
26
19
25
No Item No Item No Item
1. Power On / Off 11. HDMI 21. Volume - / +
2. Freeze 12. User 2 22. 3D Menu On / Off
3. Display Blank / Audio Mute 13. User 1 23. VGA
4. Mouse Left Click 14. Source 24. Video
5. Enter 15. Brightness Mode 25. User 3
6. Laser 16. Mouse On / Off 26. Numeric Keypad (0-9)
7. Page - 17. Mute 27. Resync
8. Keystone - / + 18. Mouse Right Click
9. Menu 19. Four Directional Select Keys
10. Aspect Ratio 20. Page +
Note: Some keys may have no function for models that do not support these features.
English
13
SETUP AND INSTALLATION
Installing the projector
Your projector is designed to be installed in one of four possible positions.
Your room layout or personal preference will dictate which installation location you select. Take into consideration
the size and position of your screen, the location of a suitable power outlet, as well as the location and distance
between the projector and the rest of your equipment.
Table mount front Ceiling mount front
Table mount rear Ceiling mount rear
Table mount front
(For short-throw lens models)
Ceiling mount front
(For short-throw lens models)
Table mount rear
(For short-throw lens models)
Ceiling mount rear
(For short-throw lens models)
English
14
SETUP AND INSTALLATION
Projector should be placed at on a surface and 90 degrees / perpendicular to the screen.
How to determine projector location for a given screen size, please refer to distance table on pages
55-57.
How to determine screen size for a given distance, please refer to distance table on pages 55-57.
Note: The further away the projector is placed from the screen the projected image size increases and vertical
offset also increases proportionally.
IMPORTANT!
Do not operate the projector in any orientation other that table top or ceiling mount. The projector should
be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate
the warranty and may shorten the lifetime of the projector lamp or the projector itself. For none standard
installation advise please contact Optoma.
English
15
SETUP AND INSTALLATION
Projector installation notice
Place the projector in a horizontal position.
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed
in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically,
and may lead to other unpredictable damages.
15°
-15°
Allow at least 30 cm clearance around the exhaust vent.
Minimum 100mm
(3.94 inches)
Minimum 300mm
(11.81 inches)
Minimum 300mm
(11.81 inches)
Minimum 100mm
(3.94 inches)
Minimum 100mm
(3.94 inches)
Minimum 100mm
(3.94 inches)
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature within
the enclosure does not exceed operation temperature while the projector is running, and the air intake
and exhaust vents are unobstructed.
All enclosures should pass a certied thermal evaluation to ensure that the projector does not recycle
exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the
acceptable operation temperature range.
English
16
SETUP AND INSTALLATION
Connecting sources to the projector
MOLEX
MOLEX
1
8
2
3
4
5
6
10
11
12
7
9
13
14
15
No
Item
No
Item
No
Item
No
Item
1.
RJ-45 cable
(Cat5 cable)
5.
RCA Component
Cable
9. USB Cable 13. HDMI Dongle
2. RJ-45 Cable 6. VGA In Cable 10. S/PDIF Out Cable 14. RS232 Cable
3. HDMI Cable 7. Audio In Cable 11. USB Power Cable 15. Power Cord
4. MHL Cable 8. 12V DC Jack 12. Audio Out Cable
English
17
SETUP AND INSTALLATION
Adjusting the projector image
Image height
The projector is equipped with elevator feet for adjusting the image height.
1. Locate the adjustable foot you wish to adjust on the underside of the projector.
2. Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
Zoom, lens shift, and focus
To adjust the image size and position, do the following:
a. To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease
the projected image size.
b. To adjust the image position, turn the lens shift dial clockwise or counterclockwise to adjust the
position of the projected image vertically.
Zoom Lever
Lens Shift
English
18
SETUP AND INSTALLATION
To adjust the focus, turn the focus ring clockwise or counterclockwise until the image is sharp and
legible.
Focus Ring Focus Ring
For short-throw lens models
Note: The projector will focus at a distance of 1.3m to 9.3m or 0.5m to 5.2m (for short-throw lens
models).
Remote setup
Installing / replacing the batteries
Two AAA size batteries are supplied for the remote control.
1. Remove the battery cover on the back of the remote control.
2. Insert AAA batteries in the battery compartment as illustrated.
3. Replace back cover on remote control.
Note: Replace only with the same or equivalent type batteries.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries have different characteristics.
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or
cause chemical leakage in old batteries.
Remove batteries as soon as the are depleted. Chemicals that leak from batteries that come in contact
with skin can cause a rash. If you nd any chemical leakage, wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
If you will not be using the remote control for an extended period of time, remove the batteries.
When you dispose of the batteries, you must obey the law in the relative area or country.
English
19
SETUP AND INSTALLATION
Effective range
Infra-Red (IR) remote control sensor is located on the front side and top side of the projector. Ensure to hold the
remote control at an angle within 30 degrees perpendicular to the projectors IR remote control sensor to function
correctly. The distance between the remote control and the sensor should not be longer than 7 meters (~ 23 feet).
Make sure that there are no obstacles between the remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
Make sure the IR transmitter of the remote control is not being shined by sunlight or uorescent lamps
directly.
Please keep the remote controller away from uorescent lamps for over 2 meters or the remote
controller might become malfunction.
If the remote control is closed to Inverter-Type uorescent lamps, it might become ineffective from time
to time.
If the remote control and the projector are within a very short distance, the remote control might
become ineffective.
When you aim at the screen, the effective distance is less than 5 meters from the remote control to the
screen and reecting the IR beams back to the projector. However, the effective range might change
according to screens.
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+Laser
Enter
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1
2
Menu
3
3D
4
HDMI
5
VGA
6
Vide o
7
User 1
8
User 2
9
User 3
Source
0
Resync
Page+
Laser
Enter
Approx. ±15°
Approx. ±15°
English
20
USING THE PROJECTOR
Powering on / off the projector
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+Laser
Enter
or
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+Laser
Enter
Powering on
1. Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will
turn red.
2. Turn on the projector by pressing the “ ” button on the projector keypad or the remote control.
3. A start up screen will display in approximately 10 seconds and the On/Standby LED will be ashing
blue.
Note: The rst time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
English
21
USING THE PROJECTOR
Powering off
1. Turn off the projector by pressing the “ ” button on the projector keypad or the remote control.
2. The following message will be displayed:
Power Off
Power Off?
Press power key again.
3. Press the “ ” button again to conrm, otherwise the message will disappear after 15 seconds. When
you press the “ ” button for the second time, the projector will shut down.
4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/
Standby LED will ash blue. When the On/Standby LED turns solid red, this indicates the projector has
entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle
has nished and the projector has entered standby mode. When the projector is in standby mode,
simply press the “ ” button again to turn on the projector.
5. Disconnect the power lead from the electrical outlet and the projector.
Note: It is not recommended that the projector is turned on immediately, right after a power off procedure.
English
22
USING THE PROJECTOR
Selecting an input source
Turn on the connected source that you want to display on the screen, such as computer, notebook, video player,
etc. The projector will automatically detect the source. If multiple sources are connected, press the “ ” button on
the projector keypad or the Source button on the remote control to select the desired input.
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+Laser
Enter
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+Laser
Enter
or
English
23
USING THE PROJECTOR
Menu navigation and features
The projector has multilingual on-screen display menus that allow you to make image adjustments and change a
variety of settings. The projector will automatically detect the source.
1. To open the OSD menu, press the “ ” button on the projector keypad or the Menu button on the
remote control.
2. When OSD is displayed, use pq keys to select any item in the main menu. While making a selection
on a particular page, press the “ ” button on the projector keypad or the Enter button on the remote
control to enter sub menu.
3. Use pq keys to select the desired item in the sub menu and then press /Enter to view further
settings. Adjust the settings by using tu keys.
4. Select the next item to be adjusted in the sub menu and adjust as described above.
5. Press to conrm, and the screen will return to the main menu.
6. To exit, press /Menu again. The OSD menu will close and the projector will automatically save the
new settings.
Sub Menu
Main Menu
Settings
Navigation guide
Display
Image Settings
3D
Aspect Ratio
Edge Mask
Digital Zoom
Image Shift
Select Exit Enter
English
24
USING THE PROJECTOR
OSD Menu tree
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Display Image Settings
Display Mode
Presentation
Bright
HDR
Cinema
Game
sRGB
DICOM SIM.
Blending
User
3D
Wall Color
Off [Default]
Blackboard
Light Yellow
Light Green
Light Blue
Pink
Gray
Dynamic Range
HDR
Off
Auto
HDR Picture
Mode
Bright
Standard [Default]
Film
Details
SMPTE 2084
HDR Demo
Mode
Off
On
Brightness -50 ~ 50
Contrast -50 ~ 50
Sharpness 1 ~ 15
Color -50 ~ 50
Tint -50 ~ 50
Gamma
Film
Video
Graphics
Standard(2.2)
1.8
2.0
2.4
English
25
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Display Image Settings
Color Settings
BrilliantColor
TM
1 ~ 10
Color
Temperature
Warm
Standard
Cool
Cold
CMS
Color
R [Default]
G
B
C
Y
M
W
x offset -50 ~ 50 [Default: 0]
y offset -50 ~ 50 [Default: 0]
Brightness -50 ~ 50 [Default: 0]
Reset
Cancel [Default]
Yes
Exit
RGB Gain/Bias
Red Gain -50 ~ 50
Green Gain -50 ~ 50
Blue Gain -50 ~ 50
Red Bias -50 ~ 50
Green Bias -50 ~ 50
Blue Bias -50 ~ 50
Reset
Cancel [Default]
Yes
Exit
Color Space
[Not HDMI Input]
Auto [Default]
RGB
YUV
Color Space
[HDMI Input]
Auto [Default]
RGB(0~255)
RGB(16~235)
YUV
Signal
Automatic
Off
On [Default]
Frequency
-50 ~ 50 (depends on signal)
[Default: 0]
Phase
0 ~ 31 (depends on signal)
[Default: 0]
H. Position
-50 ~ 50 (depends on signal)
[Default: 0]
V. Position
-50 ~ 50 (depends on signal)
[Default: 0]
Exit
English
26
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Display
Image Settings
UltraDetail
Off
1
2
3
Brightness Mode
Bright
Eco.
Dynamic
Eco+
3D
3D Mode
Off
DLP-Link [Default]
IR
3D2D
3D [Default]
L
R
3D Sync Invert
Off [Default]
On
Aspect Ratio
4:3
16:9
16:10
LBX
Superwide
Native
Auto
Edge Mask 0 ~ 10 [Default: 0]
Digital Zoom -5 ~ 25 [Default: 0]
Image Shift
H
-100 ~ 100 [Default: 0]
V
-100 ~ 100 [Default: 0]
Audio
Internal
Speaker
Off
On [Default]
Audio Out
Off
On [Default]
Mute
Off [Default]
On
Volume 0 ~ 10 [Default: 5]
Audio Input
HDMI1
Audio in
Default [Default]
HDMI2
Audio in
Default [Default]
HDBaseT
(only applicable
for models with
HDBaseT)
Audio in
Default [Default]
English
27
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Setup
Projection
Front [Default]
Rear
Ceiling-top
Rear-top
Lamp Settings
Lamp Reminder
Off
On [Default]
Lamp Reset
Cancel [Default]
Yes
Filter Settings
Filter Usage
Hours
(read only)
Optional Filter
Installed
Yes
No
Filter Reminder
Off
300hr
500hr [Default]
800hr
1000hr
Filter Reset
Cancel [Default]
Yes
Power Settings
Direct Power On
Off [Default]
On
Signal Power On
Off [Default]
On
Auto Power Off
(min.)
0 ~ 180 (5 min increments)
[Default: 20]
Sleep Timer
(min.)
0 ~ 990 (30 min increments) [Default:
0]
Always On
No [Default]
Yes
Quick Resume
Off [Default]
On
Power Mode
(Standby)
Active
Eco [Default]
Security
Security
Off
On
Security Timer
Month
Day
Hour
Change
Password
Test Pattern
Green Grid
Magenta Grid
White Grid
White
Off
English
28
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Setup
Remote
Settings
[depends on
remote]
IR Function
On [Default]
Front
Top
Off
Remote Code 00~99
User1
Test Pattern
LAN
CMS
Color Temp
Gamma
Auto Source
Projection
Lamp Settings
Zoom
MHL
Dynamic Range [Default]
User2
Test Pattern
LAN
CMS
Color Temp
Gamma
Auto Source
Projection
Lamp Settings
Zoom
MHL [Default]
Dynamic Range
User3
Test Pattern
LAN
CMS
Color Temp
Gamma
Auto Source
Projection
Lamp Settings
Zoom [Default]
MHL
Dynamic Range
Projector ID 00 ~ 99
12V Trigger
On
Off
HDBaseT
Control
(only applicable
for models with
HDBaseT)
Ethernet
On
Off
RS232
On
Off
English
29
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Setup Options
Language
English [Default]
Deutsch
Français
Italiano
Español
Português
簡体中文
日本
한국어
Русский
Menu Settings
Menu Location
Top Left
Top Right
Center [Default]
Bottom Left
Bottom Right
Menu Timer
Off
5sec
10sec [Default]
Auto Source
Off [Default]
On
Input Source
HDMI1
HDMI2
VGA
HDBaseT (only applicable for models
with HDBaseT)
High Altitude
Off [Default]
On
Display Mode
Lock
Off [Default]
On
Keypad Lock
Off [Default]
On
Information Hide
Off [Default]
On
Logo
Default [Default]
Neutral
Background
Color
None [Default]
Blue
Red
Green
Gray
HDMI 1 EQ 1 ~ 7 [Default: 4]
HDMI 2 EQ 1 ~ 7 [Default: 4]
English
30
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Setup Reset
Reset OSD
Cancel [Default]
Yes
Reset to Default
Cancel [Default]
Yes
Network
LAN
Network Status (read only)
MAC Address (read only)
DHCP
Off [Default]
On
IP Address 192.168.0.100 [Default]
Subnet Mask 255.255.255.0 [Default]
Gateway 192.168.0.254 [Default]
DNS 192.168.0.51 [Default]
Reset
Control
Crestron
Off
On [Default]
Note: Port 41794.
Extron
Off
On [Default]
Note: Port 2023.
PJ Link
Off
On [Default]
Note: Port 4352
AMX Device
Discovery
Off
On [Default]
Note: Port 9131
Telnet
Off
On [Default]
Note: Port 23
HTTP
Off
On [Default]
Note: Port 80
Control4
Off
On
Note: Port 4774
English
31
USING THE PROJECTOR
Main
Menu
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Info
Regulatory
Serial Number
Source
Resolution 00x00
Refresh Rate 0.00Hz
Display Mode
Power Mode
(Standby)
Lamp Hours
Bright 0 hr
Eco. 0 hr
Dynamic 0 hr
Total
Network Status
IP Address
Projector ID 00 ~ 99
Color Depth
Color Format
Filter Usage
Hours
Brightness
Mode
FW Version
System
LAN
MCU
English
32
USING THE PROJECTOR
Display menu
Display image settings menu
Display Mode
There are many factory presets optimized for various types of images.
Presentation: This mode is suitable for showing in front of public in connection to the PC.
Bright: Maximum brightness from PC input.
HDR: Decodes and displays High Dynamic Range (HDR) content for the deepest blacks, brightest
whites, and vivid cinematic color using REC.2020 color gamut. This mode will be automatically
enabled if HDR is set to ON (and HDR Content is sent to projector – 4K UHD Blu-ray, 1080p/4K UHD
HDR Games, 4K UHD Streaming Video). While HDR mode is active, other display modes (Cinema,
Reference, etc.) cannot be selected as HDR delivers color that is highly accurate, exceeding the color
performance of the other display modes.
Cinema: Provides the best colors for watching movies.
Game: Select this mode to increase the brightness and response time level for enjoying video games.
sRGB: Standardized accurate color.
DICOM SIM.: This mode can project a monochrome medical image such as an X ray radiography,
MRI, etc.
Blending: Select this mode when projecting one image from different projectors.
User: Memorize user’s settings.
3D: To experience the 3D effect, you need to have 3D glasses. Make sure your PC/portable device
has a 120 Hz signal output quad buffered graphics card and a 3D Player installed.
Wall Color
Use this function to obtain an optimized screen image according to the wall color. Select between off, blackboard,
light yellow, light green, light blue, pink, and gray.
Dynamic Range
Congure the High Dynamic Range (HDR) setting and its effect when displaying video from 4K Blu-ray players and
streaming devices.
Note: HDMI1 and VGA do not support Dynamic Range.
HDR
Off: Turn off HDR Processing. When set to Off, the projector will NOT decode HDR content.
Auto: Auto detect HDR signal.
HDR Picture Mode
Bright: Choose this mode for brighter more saturated colors.
Standard: Choose this mode for natural looking colors with a balance of warm and cool tones.
Film: Choose this mode for improved detail and image sharpness.
Details: The signal comes from OETF conversion to achieve the best color matching.
SMPTE 2084: HDR ETOF follows SMPTE 2084 specication.
HDR Demo Mode
This feature enables you to see the difference in the image quality between the raw unprocessed image
and the image processed as processed by the HDR.
English
33
USING THE PROJECTOR
Brightness
Adjust the brightness of the image.
Contrast
The contrast controls the degree of difference between the lightest and darkest parts of the picture.
Sharpness
Adjust the sharpness of the image.
Color
Adjust a video image from black and white to fully saturated color.
Tint
Adjust the color balance of red and green.
Gamma
Set up gamma curve type. After the initial setup and ne tuning is completed, utilize the Gamma Adjustment steps
to optimize your image output.
Film: For home theater.
Video: For video or TV source.
Graphics: For PC / Photo source.
Standard(2.2): For standardized setting.
1.8 / 2.0 / 2.4: For specic PC / Photo source.
Color Settings
Congure the color settings.
BrilliantColor
TM
: This adjustable item utilizes a new color-processing algorithm and enhancements to
enable higher brightness while providing true, more vibrant colors in picture.
Color Temperature: Select a color temperature from Warm, Standard, Cool, or Cold.
CMS (Color Management System): Select one of the colors (R/G/B/C/M/Y) to adjust its x/y offset and
brightness.
± Color: Select between red (R), green (G), blue (B), cyan (C), yellow (Y), magenta (M), and white
(W) color.
± x offset: Adjust the x offset value of the selected color.
± y offset: Adjust the y offset value of the selected color.
± Brightness: Adjust the brightness value of the selected color.
± Reset: Return the factory default settings for color adjustments.
± Exit: Exit the “CMS” menu.
RGB Gain/Bias: This settings allows to congure the brightness (gain) and contrast (bias) of an
image.
± Reset: Return the factory default settings for RGB gain/bias.
± Exit: Exit the “RGB Gain/Bias” menu.
Color Space (non-HDMI input only): Select an appropriate color matrix type from the following:
AUTO, RGB, or YUV.
Color Space (HDMI input only): select an appropriate color matrix type from the following: Auto,
RGB(0-255), RGB(16-235), and YUV.
English
34
USING THE PROJECTOR
Signal
Adjust the signal options.
Automatic: Congure automatically the signal (the frequency and phase items are grayed out). If
automatic is disabled, the frequency and phase items will appear for tuning and saving the settings.
Frequency: Change the display data frequency to match the frequency of your computer’s graphic
card. Use this function only if the image appears to icker vertically.
Phase: Synchronize the signal timing of the display with the graphic card. If the image appears to be
unstable or ickers, use this function to correct it.
H. Position: Adjust the horizontal positioning of the image.
V. Position: Adjust the vertical positioning of the image.
Exit: Exit the “Signal” menu.
Note: This menu is only available if the input source is RGB/Component.
UltraDetail
Reduce the edges of the projected image to produce a clear and highly detailed image.
Brightness Mode
Adjust the brightness mode settings for lamp-based projectors.
Bright: Choose “Bright” to increase the brightness.
Eco.: Choose “Eco.” to dim the projector lamp which will lower power consumption and extend the
lamp life.
Dynamic: Choose “Dynamic” to dim the lamp power which will be based on brightness level of the
content and adjust lamp power consumption between 100% and 30% dynamically. The lamp life will
be extended.
Eco+: When Eco+ mode is activated, the brightness level of the content is automatically detected to
signicantly reduced lamp power consumption (up to 70%) during periods of inactivity.
Reset
Return the factory default settings for color settings.
English
35
USING THE PROJECTOR
Display 3D menu
Note:
This projector is a 3D ready projector with DLP-Link 3D solution.
Please make sure your 3D glasses are use for DLP-Link 3D before enjoy your video.
This projector supports frame sequential (page-ip) 3D via HDMI1/HDMI2/VGA ports.
To enable 3D mode, the input frame rate should be set to 120Hz only, lower or higher frame rate is not
supported.
To reach the best performance, resolution 1920x1080 is recommended, please be noted that 4K
(3840x2160) resolution is not supported in 3D mode.
3D Mode
Use this option to disable the 3D function or select the appropriate the 3D function.
Off: Select “Off” to turn off 3D mode.
DLP-Link: Select to use optimized settings for DLP 3D Glasses.
IR: Select “IR” to use optimized setting for IR 3D Glasses.
3D → 2D
Use this option to specify how the 3D content should appear on the screen.
3D: Display 3D signal.
L (Left): Display the left frame of 3D content.
R (Right): Display the right frame of 3D content.
3D Sync Invert
Use this option to enable/disable the 3D sync invert function.
Display aspect ratio menu
Aspect Ratio
Select the aspect ratio of the displayed image between the following options:
4:3: This format is for 4:3 input sources.
16:9: This format is for 16:9 input sources, like HDTV and DVD enhanced for Wide screen TV.
16:10: This format is for 16:10 input sources, like widescreen laptops.
LBX: This format is for non-16x9, letterbox source and if you use external 16x9 lens to display 2.35:1
aspect ratio in full resolution.
Superwide: Use this special 2.0:1 aspect ratio to display both 16:9 and 2.35:1 aspect ratio movies
without black bars at the top and bottom of the screen.
Native: This format displays the original image without any scaling.
Auto: Automatically selects the appropriate display format.
Note:
Detailed informations about LBX mode:
± Some Letter-Box Format DVDs are not enhanced for 16x9 TVs. In this situation, the image
will not look right when displaying image in 16:9 mode. In this situation, please try to use the
4:3 mode to view the DVD. If the content is not 4:3, there will be black bars around the image
in 16:9 display. For this type of content, you can use LBX mode to ll the image on the 16:9
display.
English
36
USING THE PROJECTOR
± If you use an external anamorphic lens, this LBX mode also allows you to watch a 2.35:1
content (include Anamorphic DVD and HDTV lm source) that supports anamorphic wide is
enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Lamp
power and vertical resolution are fully utilized.
To use the superwide format, do the following:
a) Set the screen aspect ratio to 2.0:1.
b) Select “Superwide” format.
c) Align the projector image correctly on the screen.
4K UHD scaling table:
16 : 9 screen 480i/p 576i/p 720p 1080i/p
2160p
4x3 Scale to 2880 x 2160.
16x9 Scale to 3840 x 2160.
LBX Get the central 3840 x 1620 image, and then scale to 3840 x 2160 for display.
Native mode 1:1 mapping centered.
No scaling will be made; the displayed resolution depends on input source.
Auto -If source is 4:3, the screen type will be scaled to 2880 x 2160.
-If source is 16:9, the screen type will be scaled to 3840 x 2160.
-If source is 15:9, the screen type will be scaled to 3600 x 2160.
-If source is 16:10, the screen type will be scaled to 3456 x 2160.
Auto mapping rule:
Input resolution Auto/Scale
H-resolution V-resolution 3840 2160
4:3
640 480 2880 2160
800 600 2880 2160
1024 768 2880 2160
1280 1024 2880 2160
1400 1050 2880 2160
1600 1200 2880 2160
Wide Laptop
1280 720 3840 2160
1280 768 3600 2160
1280 800 3456 2160
SDTV
720 576 2700 2160
720 480 3240 2160
HDTV
1280 720 3840 2160
1920 1080 3840 2160
Display edge mask menu
Edge Mask
Use this function to remove the video encoding noise on the edge of video source.
English
37
USING THE PROJECTOR
Display digital zoom menu
Digital Zoom
Use to reduce or magnify an image on the projection screen.
Display image shift menu
Image Shift
Adjust the projected image position horizontally (H) or vertically (V).
Audio menu
Audio internal speaker menu
Internal Speaker
Use this option to turn on or off the internal speaker.
Off: Choose “Off” to turn off the internal speaker.
On: Choose “On” to turn on the internal speaker.
Audio audio out menu
Audio Out
Choose the “On” or “Off” to turn on or off the audio out.
Audio mute menu
Mute
Use this option to temporarily turn off the sound.
On: Choose “On” to turn mute on.
Off: Choose “Off” to turn mute off.
Note: “Mute” function affects both internal and external speaker volume.
Audio volume menu
Volume
Adjust the volume level.
Audio audio input menu
Audio Input
Select the audio input port for the video sources as follows:
Default: Audio input port is selected automatically.
Audio in: AUDIO IN Connector (RCA) if the video source is Composite.
English
38
USING THE PROJECTOR
Setup menu
Setup projection menu
Projection
Select the preferred projection between front, rear, ceiling-top, and rear-top.
Setup lamp settings menu
Lamp Reminder
Choose this function to show or to hide the warning message when the changing lamp message is displayed. The
message will appear 30 hours before suggested replacement of lamp.
Lamp Reset
Resets the lamp hour counter after replacing the lamp.
Setup lter settings menu
Filter Usage Hours
Display the lter time.
Optional Filter Installed
Set the warning message setting.
Yes: Display warning message after 500 hours of use.
Note: “Filter Usage Hours / Filter Reminder / Filter Reset” will only appear when “Optional Filter
Installed” is “Yes”.
No: Turn off warning message.
Filter Reminder
Choose this function to show or hide the warning message when the changing lter message is displayed. The
available options include 300hr, 500hr, 800hr, and 1000hr.
Filter Reset
Reset the dust lter counter after replacing or cleaning the dust lter.
Setup power settings menu
Direct Power On
Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied,
without pressing the “Power” key on the projector keypad or on the remote control.
Signal Power On
Choose “On” to activate Signal Power mode. The projector will automatically power on when a signal is detected,
without pressing the “Power” key on the projector Keypad or on the remote control.
Note:
If the “Signal Power On” option is turned “On”, the power consumption of the projector in standby
mode will be over 3W.
“Signal Power On” can support VGA (RGB signal) and HDMI.
English
39
USING THE PROJECTOR
Auto Power Off (min.)
Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the
projector. The projector will automatically power off when the countdown has nished (in minutes).
Sleep Timer (min.)
Congure the sleep timer.
Sleep Timer (min.): Sets the countdown timer interval. The countdown timer will start, with or without
a signal being sent to the projector. The projector will automatically power off when the countdown has
nished (in minutes).
Note: The Sleep Timer is reset every time when the projector is powered off.
Always On: Check to set the sleep timer always on.
Quick Resume
Set the quick resume setting.
On: If the projector is accidentally turned off, this feature allows the projector to be instantly powered
on again, if selected within a period of 100 seconds.
Off: The fan will start cooling the system after 10 seconds when user turns off the projector.
Power Mode (Standby)
Set the power mode setting.
Active: Choose “Active” to return to normal standby.
Eco: Choose “Eco.” to save power dissipation further < 0.5W.
Setup security menu
Security
Enable this function to prompt for a password before using the projector.
On: Choose “On” to use security verication when the turning on the projector.
Off: Choose “Off” to be able to switch on the projector without password verication.
Security Timer
Can be select the time (Month/Day/Hour) function to set the number of hours the projector can be used. Once this
time has elapsed you will be requested to enter your password again.
Change Password
Use to set or modify the password that is prompted when turning the projector on.
Setup test pattern menu
Test Pattern
Select the test pattern from green grid, magenta grid, white grid, white, or disable this function (off).
English
40
USING THE PROJECTOR
Setup remote settings menu
IR Function
Set the IR function setting.
On: Choose “On”, the projector can be operated by the remote control from top and front IR receivers.
Front: Choose “Front”, the projector can be operated by the remote control from the front IR receiver.
Top: Choose “Top”, the projector can be operated by the remote control from the top IR receiver.
Off: Choose “Off”, the projector can’t be operated by the remote control. By selecting “Off”, you will be
able to use the Keypad keys.
Remote Code
Set the remote custom code by pressing the remote ID button for 3 seconds and you will notice the remote
indicator (above the Off button) starts blinking. Then, input a number between 00-99 using the keyboard numbered
keys. After inserting the number, the remote indicator blinks twice quickly indicating that the remote code has
changed.
User1/ User2/ User3
Assign the default function for User1, User2, or User3 between Test Pattern, LAN, CMS, Color Temp, Gamma, Auto
Source, Projection, Lamp Settings, Zoom, MHL, or Dynamic Range.
Setup projector ID menu
Projector ID
ID denition can be set up by menu (range 0-99), and allow user control an individual projector by using RS232 command.
Setup 12V trigger menu
12V Trigger
Use this function to enable or disable the trigger.
Reserved
IR_IN & detect
GND
Off: Choose “Off” to disable the trigger.
On: Choose “On” to enable the trigger.
Setup HDBaseT control menu
Ethernet
Choose “On” to set the serial port path to HDBaseT.
RS232
Choose “On” to set the serial port path to RS232.
English
41
USING THE PROJECTOR
Setup options menu
Language
Select the multilingual OSD menu between English, German, French, Italian, Spanish, Portuguese,
Simplied Chinese, Japanese, Korean, and Russian.
Menu Settings
Set the menu location on the screen and congure menu timer settings.
Menu Location: Select the menu location on the display screen.
Menu Timer: Set the duration where the OSD menu stays visible on the screen.
Auto Source
Choose this option to let the projector automatically nd an available input source.
Input Source
Select the input source between HDMI1, HDMI2, VGA and HDBaseT.
Note: HDBaseT option is only applicable for models with HDBaseT.
High Altitude
When “On” is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin.
Display Mode Lock
Choose “On” or “Off” to lock or unlock adjusting display mode settings.
Keypad Lock
When the keypad lock function is “On”, the Keypad will be locked. However, the projector can be operated by the
remote control. By selecting “Off”, you will be able to reuse the Keypad.
Information Hide
Enable this function to hide the information message.
Off: Choose “Off” to show the “searching” message.
On: Choose “On” to hide the info message.
Logo
Use this function to set the desired startup screen. If changes are made, they will take effect the next time the
projector is powered on.
Default: The default startup screen.
Neutral: Logo is not displayed on startup screen.
Background Color
Use this function to display a blue, red, green, gray color, or none when no signal is available.
HDMI 1 EQ
Set the HDMI port EQ value for HDMI1.
HDMI 2 EQ
Set the HDMI port EQ value for HDMI2/MHL.
Note:
HDMI EQ analyses the signal data and eliminates distortion due to signal loss when using long HDMI
cables. The HDMI receiver also includes a timing adjustment circuit that removes timing jitter, restoring
the HDMI signal to optimal transmission levels.
3840x2160@60Hz suggests using the 4K HDMI cable under 5 meters.
3840x2160@30Hz/25Hz/24Hz suggests using the 4K HDMI cable under 15 meters.
English
42
USING THE PROJECTOR
Setup reset OSD menu
Reset OSD
Return the factory default settings for OSD menu settings.
Reset to Default
Return the factory default settings for all settings.
Network menu
Network LAN menu
Network Status
Display the network connection status (read-only).
MAC Address
Display the MAC address (read-only).
DHCP
Use this option to enable or disable the DHCP function.
On: Projector will obtain an IP address automatically from your network.
Off: To assign IP, subnet mask, gateway, and DNS conguration manually.
Note: Exiting OSD will automatically apply the entered values.
IP Address
Display the IP address.
Subnet Mask
Display subnet mask number.
Gateway
Display the default gateway of the network connected to the projector.
DNS
Display the DNS number.
How to use web browser to control your projector
1. Turn “On” the DHCP option on projector to allow a DHCP server to automatically assign an IP address.
2. Open the web browser in your PC and type in the projector’s IP address (“Network > LAN > IP
Address”).
3. Enter the user name and password, and click “Login”.
The projector’s conguration web interface opens.
Note:
The default user name and password is “admin”.
The steps in this section is based on Windows 7 operating system.
English
43
USING THE PROJECTOR
Making a direct connection from your computer to the projector*
1. Turn “Off” the DHCP option on the projector.
2. Congure the IP address, Subnet Mask, Gateway, and DNS on projector (“Network > LAN”).
3. Open Network and Sharing Center page on your PC, and assign the identical network parameters to
your PC as set on projector. Click “OK” to save the parameters.
4. Open the web browser on your PC and type in to the URL eld the IP address, assigned in step 3.
Then press “Enter” key.
Reset
Reset all values for LAN parameters.
Network control menu
Crestron
Use this function to select the network function (port: 41794).
For more information, please visit http://www.crestron.com and www.crestron.com/getroomview.
Extron
Use this function to select the network function (port: 2023).
PJ Link
Use this function to select the network function (port: 4352).
AMX Device Discovery
Use this function to select the network function (port: 9131).
Telnet
Use this function to select the network function (port: 23).
HTTP
Use this function to select the network function (port: 80).
Control4
Use this function to select the network function (port: 4774).
English
44
USING THE PROJECTOR
Setup network control settings menu
LAN_RJ45 function
For simplicity and ease of operation, the projector provides diverse networking and remote management features.
The LAN / RJ45 function of the projector through a network, such as remotely manage: Power On / Off, brightness,
and contrast settings. Also, you can view the projector status information, such as: Video- Source, Sound-Mute, etc.
(Ethernet)
Projector
Wired LAN terminal functionalities
This projector can be controlled by using a PC (laptop) or other external device via LAN / RJ45 port and compatible
with Crestron / Extron / AMX (Device -Discovery) / PJLink.
Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.
Extron is a registered trademark of Extron Electronics, Inc. of the United States.
AMX is a registered trademark of AMX LLC of the United States.
PJLink applied for trademark and logo registration in Japan, the United States of America, and other
countries by JBMIA.
The projector is supported by the specied commands of the Crestron Electronics controller and related software,
for example RoomView®.
http://www.crestron.com/
This projector is compliant to support Extron device(s) for reference.
http://www.extron.com/
This projector is supported by AMX ( Device Discovery ).
http://www.amx.com/
This projector supports all commands of PJLink Class1 (Version 1.00).
http://pjlink.jbmia.or.jp/english/
For more detailed information about the various types of external devices which can be connected to the LAN /
RJ45 port and remote control the projector, as well as the supported commands for these external devices, please
contact the Support-Service directly.
English
45
USING THE PROJECTOR
LAN RJ45
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop).
2. On the PC (Laptop), select Start > Control Panel > Network Connections.
3. Right-click on the Local Area Connection, and select Property.
4. In the Properties window, select the General tab, and select Internet Protocol (TCP / IP).
English
46
USING THE PROJECTOR
5. Click “Properties”.
6. Type in the IP address and Subnet mask, then press “OK”.
7. Press the “Menu” button on the projector.
8. Open on projector Network > LAN.
9. Enter the following connection parameters:
± DHCP: Off
± IP Address: 192.168.0.100
± Subnet Mask: 255.255.255.0
± Gateway: 192.168.0.254
± DNS: 192.168.0.51
10. Press “Enter” to conrm settings.
11. Open a web browser, for example Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher
installed.
12. In the Address bar, input the projector’s IP address: 192.168.0.100.
English
47
USING THE PROJECTOR
13. Press “Enter”.
The projector is setup for remote management. The LAN / RJ45 function displays as follows:
System Status page General Setup page
Projector Setup page Network Setup page
Alert Setup page Reset to Default page
Reboot page
English
48
USING THE PROJECTOR
RS232 by Telnet Function
There is alternative RS232 command control way, in projector so called “RS232 by TELNET” for LAN / RJ45
interface.
Quick Start-Guide for “RS232 by Telnet”
Check and get the IP address on OSD of the projector.
Make sure that the PC / laptop can access the web-page of the projector.
Make sure that “Windows Firewall” setting is set disabled in case of “TELNET” function ltering out by
PC / laptop.
.
1. Select Start > All Programs.> Accessories > Command Prompt.
2. Input the command format as follows:
± telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)
± (ttt.xxx.yyy.zzz: IP-Address of the projector)
3. If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key pressed, the
RS232 command will be workable.
Specication for “RS232 by TELNET”:
1. Telnet: TCP.
2. Telnet port: 23 (for more detail, kindly please get contact with the service agent or team).
3. Telnet utility: Windows “TELNET.exe” (console mode).
4. Disconnection for RS232-by-Telnet control normally: Close
5. Windows Telnet utility directly after TELNET connection ready.
± Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload for
Telnet-Control application.
± Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232 command for
Telnet-Control.
± Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more than 200 (ms).
English
49
USING THE PROJECTOR
Info menu
Info menu
View the projector information as listed below:
Regulatory
Serial Number
Source
Resolution
Refresh Rate
Display Mode
Power Mode (Standby)
Lamp Hours
Network Status
IP Address
Projector ID
Color Depth
Color Format
Filter Usage Hours
Brightness Mode
FW Version
English
50
MAINTENANCE
Replacing the lamp
The projector automatically detects the lamp life. When the lamp life is nearing the end of use, a warning message
will appear on the screen.
Warning
Lamp Warning
Lamp life exceeded.
When you see this message, please contact your local reseller or service center to change the lamp as soon as
possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.
Warning: If ceiling mounted, please use caution when opening the lamp access panel. It is
recommended to wear safety glasses if changing the bulb when ceiling mounted. Caution must be used
to prevent any loose parts from falling out of projector.
Warning: Lamp compartment is hot! Allow it to cool down before changing lamp!
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The
bulb may shatter and cause injury if it is dropped.
English
51
MAINTENANCE
Replacing the lamp (continued)
3
2
1
1
6
4
5
Procedure:
1. Switch off the power to the projector by pressing the “ ” button on the projector keypad or the remote
control.
2. Allow the projector to cool down for at least 30 minutes.
3. Disconnect the power cord.
4. Remove the 2 screws securing the top cover. 1
5. Remove the top cover. 2
6. Remove the screw on the lamp module. 3
7. Lift up the lamp handle. 4
8. Remove the lamp cord. 5
9. Remove the lamp module carefully. 6
10. To replace the lamp module, reverse the previous steps.
11. Turn on the projector and reset the lamp timer.
12. Lamp Reset: (i) Press “Menu” (ii) Select “Setup” (iii) Select “Lamp Settings”
(iv) Select “Lamp
Reset”
(v) Select “Yes”.
Note:
The projector cannot be turned on if the lamp cover has not been placed back on the projector.
Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean
the lamp module if it was accidentally touched.
English
52
MAINTENANCE
Installing and cleaning the dust lter
Installing the dust lter
Note: Dust lters are only required/supplied in the selected regions with excessive dust.
Cleaning the dust lter
We recommend you to clean the dust lter every three months. Clean it more often if the projector is used in a
dusty environment.
Procedure:
1. Switch off the power to the projector by pressing the “ ” button on the projector keypad or the remote
control.
2. Disconnect the power cord.
3. Pull the dust lter compartment downwards to remove it out from the bottom of the projector. 1
4. Carefully remove the air lter. Then clean or replace the dust lter. 2
5. To install the dust lter, reverse the previous steps.
1
2
English
53
ADDITIONAL INFORMATION
Compatible resolutions
Digital (HDMI 1.4)
Native resolution: 3840 x 2160 @ 30Hz
Established Timing Standard Timing
Descriptor timing
-B0 (Detail timing)
Supported Video Mode
Descriptor timing
-B1 (Detail timing)
720 x 400 @ 70Hz 1280 x 720 @ 60Hz 3840 x 2160 @ 30Hz
(default)
720 x 480i @ 60Hz 16:9 1920 x 1080p @ 60Hz
640 x 480 @ 60Hz 1280 x 800 @ 60Hz 720 x 480p @ 60Hz 4:3 1366 x 768 @ 60Hz
640 x 480 @ 67Hz 1280 x 1024 @ 60Hz 720 x 480p @ 60Hz 16:9 1920 x 1080 @ 120Hz
640 x 480 @ 72Hz 1920 x 1200 @ 60Hz
(reduced)
720 x 576i @ 50Hz 16:9
640 x 480 @ 75Hz 640 x 480 @ 120Hz 720 x 576p @ 50Hz 4:3
800 x 600 @ 56Hz 800 x 600 @ 120Hz 720 x 576p @ 50Hz 16:9
800 x 600 @ 60Hz 1024 x 768 @ 120Hz 1280 x 720p @ 60Hz 16:9
800 x 600 @ 72Hz 1280 x 800 @ 120Hz 1280 x 720p @ 50Hz 16:9
800 x 600 @ 75Hz 1920 x 1080i @ 60Hz 16:9
832 x 624 @ 75Hz 1920 x 1080i @ 50Hz 16:9
1024 x 768 @ 60Hz 1920 x 1080p @ 60Hz 16:9
1024 x 768 @ 70Hz 1920 x 1080p @ 50Hz 16:9
1024 x 768 @ 75Hz 1920 x 1080p @ 24Hz 16:9
1280 x 1024 @ 75Hz 3840 x 2160 @ 24Hz
3840 x 2160 @ 25Hz
Manufacturer's Timings: 3840 x 2160 @ 30Hz
1152 x 870 @ 75Hz 4096 x 2160 @ 24Hz
Digital (HDMI 2.0)
Native resolution: 3840 x 2160 @ 60Hz
B0 / Established Timing B0 / Standard Timing B1 / Video Mode B1 / Detail Timing
720 x 400 @ 70Hz 1280 x 720 @ 60Hz 720 x 480i @ 60Hz 16:9 1920 x 1080p @ 120Hz
640 x 480 @ 60Hz 1280 x 800 @ 60Hz 720 x 480p @ 60Hz 4:3 1366 x 768 @ 60Hz
640 x 480 @ 67Hz 1280 x 1024 @ 60Hz 720 x 480p @ 60Hz 16:9
640 x 480 @ 72Hz 1920 x 1200 @ 60Hz (reduced) 720 x 576i @ 50Hz 16:9
640 x 480 @ 75Hz 640 x 480 @ 120Hz 720 x 576p @ 50Hz 4:3
800 x 600 @ 56Hz 800 x 600 @ 120Hz 720 x 576p @ 50Hz 16:9
800 x 600 @ 60Hz 1024 x 768 @ 120Hz 1280 x 720p @ 60Hz 16:9
800 x 600 @ 72Hz 1280 x 800 @ 120Hz 1280 x 720p @ 50Hz 16:9
800 x 600 @ 75Hz 1920 x 1080i @ 60Hz 16:9
832 x 624 @ 75Hz 1920 x 1080i @ 50Hz 16:9
1024 x 768 @ 60Hz 1920 x 1080p @ 60Hz 16:9
1024 x 768 @ 70Hz 1920 x 1080p @ 50Hz 16:9
1024 x 768 @ 75Hz 1920 x 1080p @ 24Hz 16:9
1280 x 1024 @ 75Hz 3840 x 2160 @ 24Hz
3840 x 2160 @ 25Hz
Manufacturer's Timings: 3840 x 2160 @ 30Hz
1152 x 870 @ 75Hz 3840 x 2160 @ 50Hz
3840 x 2160 @ 60Hz
4096 x 2160 @ 24Hz
English
54
ADDITIONAL INFORMATION
B0 / Established Timing B0 / Standard Timing B1 / Video Mode B1 / Detail Timing
4096 x 2160 @ 25Hz
4096 x 2160 @ 30Hz
4096 x 2160 @ 50Hz
4096 x 2160 @ 60Hz
Note: Support 1920 x 1080 @ 50Hz.
Analog
Native resolution: 1920 x 1080 @ 60Hz
B0 / Established Timing B0 / Standard Timing B0 / Detail Timing B1 / Detail Timing
720 x 400 @ 70Hz 1280 x 720 @ 60Hz 1920 x 1080 @ 60Hz (default) 1366x768 @ 60Hz
640 x 480 @ 60Hz 1280 x 800 @ 60Hz 1280x800@120Hz(RB)
640 x 480 @ 67Hz 1280 x 1024 @ 60Hz
640 x 480 @ 72Hz 1900 x 1200 @ 60Hz(RB)
640 x 480 @ 75Hz 640 x 480 @ 120Hz
800 x 600 @ 56Hz 800 x 600 @ 120Hz
800 x 600 @ 60Hz 1024 x 768 @ 120Hz
800 x 600 @ 72Hz
800 x 600 @ 75Hz
832 x 624 @ 75Hz
1024 x 768 @ 60Hz
1024 x 768 @ 70Hz
1024 x 768 @ 75Hz
1280 x 1024 @ 75Hz
Manufacturer's Timings:
1152 x 870@ 75Hz
Note: Support 1920 x 1080 @ 50Hz.
English
55
ADDITIONAL INFORMATION
Image size and projection distance
Diagonal
length
(inch)
size of
16:9
Screen
Screen Size W x H Projection Distance (D)
Min Offset (Hd) Max Offset (Hd)
(m) (feet) (m) (feet)
Width Height Width Height Wide Tele Wide Tele (m) (feet) (m) (feet)
26.45 0.59 0.33 1.92 1.08 0.81 1.30 2.66 4.27 0.00 0.00 0.05 0.16
40.00 0.89 0.50 2.91 1.63 1.23 1.97 4.04 6.46 0.00 0.00 0.07 0.25
60.00 1.33 0.75 4.36 2.45 1.85 2.95 6.07 9.68 0.00 0.00 0.11 0.37
70.00 1.55 0.87 5.08 2.86 2.15 3.44 7.05 11.29 0.00 0.00 0.13 0.43
80.00 1.77 1.00 5.81 3.27 2.46 3.93 8.07 12.89 0.00 0.00 0.15 0.49
90.00 1.99 1.12 6.54 3.68 2.77 4.42 9.09 14.50 0.00 0.00 0.17 0.55
100.00 2.21 1.25 7.26 4.09 3.08 4.91 10.10 16.11 0.00 0.00 0.19 0.61
120.00 2.66 1.49 8.72 4.90 3.69 5.90 12.11 19.36 0.00 0.00 0.22 0.74
150.00 3.32 1.87 10.89 6.13 4.62 7.37 15.16 24.18 0.00 0.00 0.28 0.92
180.00 3.98 2.24 13.07 7.35 5.54 8.85 18.18 29.04 0.00 0.00 0.34 1.10
250.00 5.53 3.11 18.16 10.21 7.69 12.29 25.23 40.32 0.00 0.00 0.47 1.53
302.20 6.69 3.76 21.95 12.35 9.30 14.85 30.51 48.72 0.00 0.00 0.56 1.85
Note: Image size and distance in meters and feet.
Diagonal
length
(inch)
size of
16:9
Screen
Screen Size W x H Projection Distance (D)
Min Offset (Hd) Max Offset (Hd)
(m) (inch) (m) (inch)
Width Height Width Height Wide Tele Wide Tele (m) (inch) (m) (inch)
26.45 0.59 0.33 23.05 12.97 0.81 1.30 31.89 51.18 0.00 0.00 0.05 1.95
40.00 0.89 0.50 34.86 19.61 1.23 1.97 48.43 77.56 0.00 0.00 0.07 2.94
60.00 1.33 0.75 52.29 29.42 1.85 2.95 72.83 116.14 0.00 0.00 0.11 4.41
70.00 1.55 0.87 61.01 34.32 2.15 3.44 84.65 135.43 0.00 0.00 0.13 5.15
80.00 1.77 1.00 69.73 39.22 2.46 3.93 96.85 154.72 0.00 0.00 0.15 5.88
90.00 1.99 1.12 78.44 44.12 2.77 4.42 109.06 174.02 0.00 0.00 0.17 6.62
100.00 2.21 1.25 87.16 49.03 3.08 4.91 121.26 193.31 0.00 0.00 0.19 7.35
120.00 2.66 1.49 104.59 58.83 3.69 5.90 145.28 232.28 0.00 0.00 0.22 8.82
150.00 3.32 1.87 130.74 73.54 4.62 7.37 181.89 290.16 0.00 0.00 0.28 11.03
180.00 3.98 2.24 156.88 88.25 5.54 8.85 218.11 348.43 0.00 0.00 0.34 13.24
250.00 5.53 3.11 217.89 122.57 7.69 12.29 302.76 483.86 0.00 0.00 0.47 18.38
302.20 6.69 3.76 263.39 148.16 9.30 14.85 366.14 584.65 0.00 0.00 0.56 22.22
Note: Image size and distance in meters and inches.
English
56
ADDITIONAL INFORMATION
For short-throw lens models
Diagonal
length
(inch)
size of
16:9
Screen
Screen Size W x H Projection Distance (D)
Min Offset (Hd) Max Offset (Hd)
(m) (feet) (m) (feet)
Width Height Width Height Wide Tele Wide Tele (m) (feet) (m) (feet)
28.89 0.64 0.36 2.10 1.18 0.50 0.50 1.64 1.64 0.00 0.00 0.04 0.12
40.00 0.89 0.50 2.91 1.63 0.69 0.69 2.26 2.26 0.00 0.00 0.05 0.16
60.00 1.33 0.75 4.36 2.45 1.04 1.04 3.41 3.41 0.00 0.00 0.07 0.25
70.00 1.55 0.87 5.08 2.86 1.21 1.21 3.97 3.97 0.00 0.00 0.09 0.29
80.00 1.77 1.00 5.81 3.27 1.38 1.38 4.53 4.53 0.00 0.00 0.10 0.33
90.00 1.99 1.12 6.54 3.68 1.56 1.56 5.12 5.12 0.00 0.00 0.11 0.37
100.00 2.21 1.25 7.26 4.09 1.73 1.73 5.68 5.68 0.00 0.00 0.12 0.41
120.00 2.66 1.49 8.72 4.90 2.08 2.08 6.82 6.82 0.00 0.00 0.15 0.49
150.00 3.32 1.87 10.89 6.13 2.60 2.60 8.53 8.53 0.00 0.00 0.19 0.61
180.00 3.98 2.24 13.07 7.35 3.12 3.12 10.24 10.24 0.00 0.00 0.22 0.74
250.00 5.53 3.11 18.16 10.21 4.33 4.33 14.21 14.21 0.00 0.00 0.31 1.02
300.46 6.65 3.74 21.82 12.28 5.20 5.20 17.06 17.06 0.00 0.00 0.37 1.23
Note: Image size and distance in meters and feet.
Diagonal
length
(inch)
size of
16:9
Screen
Screen Size W x H Projection Distance (D)
Min Offset (Hd) Max Offset (Hd)
(m) (inch) (m) (inch)
Width Height Width Height Wide Tele Wide Tele (m) (inch) (m) (inch)
28.89 0.64 0.36 25.18 14.16 0.50 0.50 19.69 19.69 0.00 0.00 0.04 1.42
40.00 0.89 0.50 34.86 19.61 0.69 0.69 27.17 27.17 0.00 0.00 0.05 1.96
60.00 1.33 0.75 52.29 29.42 1.04 1.04 40.94 40.94 0.00 0.00 0.07 2.94
70.00 1.55 0.87 61.01 34.32 1.21 1.21 47.64 47.64 0.00 0.00 0.09 3.43
80.00 1.77 1.00 69.73 39.22 1.38 1.38 54.33 54.33 0.00 0.00 0.10 3.92
90.00 1.99 1.12 78.44 44.12 1.56 1.56 61.42 61.42 0.00 0.00 0.11 4.41
100.00 2.21 1.25 87.16 49.03 1.73 1.73 68.11 68.11 0.00 0.00 0.12 4.90
120.00 2.66 1.49 104.59 58.83 2.08 2.08 81.89 81.89 0.00 0.00 0.15 5.88
150.00 3.32 1.87 130.74 73.54 2.60 2.60 102.36 102.36 0.00 0.00 0.19 7.35
180.00 3.98 2.24 156.88 88.25 3.12 3.12 122.83 122.83 0.00 0.00 0.22 8.82
250.00 5.53 3.11 217.89 122.57 4.33 4.33 170.47 170.47 0.00 0.00 0.31 12.26
300.46 6.65 3.74 261.87 147.30 5.20 5.20 204.72 204.72 0.00 0.00 0.37 14.73
Note: Image size and distance in meters and inches.
English
57
ADDITIONAL INFORMATION
Width
Height
Diagonal
Top View
Side View
Projection Distance (D)
Projection Distance (D)
Screen
Screen
Screen (W)
Screen (H)
Offset (Hd)
Figure for Distance
English
58
ADDITIONAL INFORMATION
Projector dimensions and ceiling mount installation
1. To prevent damage to your projector, please use the Optoma ceiling mount.
2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to
the projector meet the following specications:
Screw type: M4*3
Minimum screw length: 10mm
Lens
English
59
ADDITIONAL INFORMATION
For short-throw lens models
Lens
Note: Please note that damage resulting from incorrect installation will void the warranty.
Warning:
If you buy a ceiling mount from another company, please be sure to use the correct screw size.
Screw size will vary depending on the thickness of the mounting plate.
Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.
Avoid installing the projector near a heat source.
English
60
ADDITIONAL INFORMATION
IR remote codes
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA
6
Video
7
User1
8
User2
9
User3
Source
0
Resync
Page+Laser
Enter
Key
Key
code
Printing-key
denition
Description
Power 81 Power on / off Press to turn on / off the projector.
Switch 3E Switch No function.
Display blank /
audio mute
8A
Press to hide / unhide the screen picture and turn off / on
audio.
Freeze 8B Freeze Press to freeze the projector image.
Mute 92 Press to momentarily turn off / on the audio.
Mouse left click L CB L No function.
Mouse right click R CC R No function.
Four
directional select
keys
C6 Up arrow
Use to select items or make adjustments to
your selection.
C8 Left arrow
C9 Right arrow
C7 Down arrow
Enter
C5 Enter
Conrm your item selection.
CA Enter
Page - C2 Page- No function.
Laser N/A Laser Use as laser pointer.
Page + C1 Page+ No function.
Keystone
-
+
85 Keystone+
No function.
84 Keystone-
English
61
ADDITIONAL INFORMATION
Key
Key
code
Printing-key
denition
Description
Volume
-
+
8C Volume +
Press to adjust to increase / decrease the volume.
8F Volume -
Aspect ratio / 1 98
/ 1
Press to change aspect ratio of a displayed image.
Use as numeric keypad number "1".
Menu / 2 88 Menu / 2
Press to display or exit the on-screen display menus
for projector.
Use as numeric keypad number "2".
3D / 3 93 3D/3
Press to manually select a 3D mode that matches
your 3D content.
Use as numeric keypad number "3".
HDMI / 4 86 HDMI/4
Press to choose HDMI source.
Use as numeric keypad number "4".
VGA / 5 D0 VGA/5
Press to choose VGA source.
Use as numeric keypad number "5".
Video / 6 D1 Video/6
Press to choose composite video source.
Use as numeric keypad number "6".
User1 / 7; User2 / 8;
User3 / 9
D2 User 1/7
User dened keys. Please see page 40 to setup.
Use as numeric keypad numbers "7", "8", and "9"
accordingly.
D3 User 2/8
D4 User 3/9
Source C3 Source Press to select an input signal.
Brightness
mode / 0
96
/ 0
Press to automatically adjust the picture brightness
to give an optimum contrast performance.
Use as numeric keypad number "0".
Re-sync C4 Re-Sync
Press to automatically synchronize the projector to the
input source.
Note:
If the projector supports Dynamic Eco / Image Care features and AV Mute is pressed, the power
consumption of the lamp becomes 30%.
Remote mouse feature simulation specication
The remote mouse feature is supported only when a computer source is selected, for example VGA or
HDMI.
If you press the “Switch” key on the remote control, you will see the cursor being displayed on the right
top corner of the screen for 15 seconds.
In remote mouse mode the cursor should move smoothly and continuously on the screen.
English
62
ADDITIONAL INFORMATION
Troubleshooting
If you experience a problem with your projector, please refer to the following information. If a problem persists,
please contact your local reseller or service center.
Image problems
No image appears on-screen
Ensure all the cables and power connections are correctly and securely connected as described in the
"Installation" section.
Ensure the pins of connectors are not crooked or broken.
Check if the projection lamp has been securely installed. Please refer to the "Replacing the Lamp"
section on pages 50-51.
Ensure that the "Mute" feature is not turned on.
Image is out of focus
Adjust the Focus Ring on the projector lens. Please see page 18.
Make sure the projection screen is between the required distance from the projector. (Please refer to
pages 55-57).
The image is stretched when displaying 16:9 DVD title
When you play anamorphic DVD or 16:9 DVD, the projector will show the best image in 16: 9 format
on projector side.
If you play the LBX format DVD title, please change the format as LBX in projector OSD.
If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD.
Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player.
Image is too small or too large
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the screen.
Press "Menu" on the projector panel, go to "Display Aspect Ratio". Try the different settings.
Image has slanted sides:
If possible, reposition the projector so that it is centered on the screen and below the bottom of the
screen.
Image is reversed
Select "Setup Projection" from the OSD and adjust the projection direction.
English
63
ADDITIONAL INFORMATION
Other problems
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the "Replacing the Lamp" section on pages 50-51.
Remote control problems
If the remote control does not work
Check the operating angle of the remote control is pointed within ±15° to the IR receiver on the
projector.
Make sure there are not any obstructions between the remote control and the projector. Move to within
7 m (23 ft) of the projector.
Make sure batteries are inserted correctly.
Replace batteries if they are exhausted.
English
64
ADDITIONAL INFORMATION
Warning indicators
When the warning indicators (see below) light up or ash, the projector will automatically shutdown:
"LAMP" LED indicator is lit red and if "On/Standby" indicator ashes red.
"TEMP" LED indicator is lit red and if "On/Standby" indicator ashes red. This indicates the projector
has overheated. Under normal conditions, the project can be switched back on.
"TEMP" LED indicator ashes red and if "On/Standby" indicator ashes red.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or
ash, please contact your nearest service center for assistance.
LED lightning messages
Message
On/Standby LED Temp LED Lamp LED
(Red) (Blue) (Red) (Red)
Standby state
(Input power cord)
Steady light
Power on (Warming)
Flashing
(0.5 sec off / 0.5 sec
on)
Power on and Lamp lighting Steady light
Power off (Cooling)
Flashing
(0.5 sec off / 0.5 sec
light). Back to red
steady light when
cooling fan turns off.
Error (Lamp failure) Flashing Steady light
Error (Fan failure) Flashing Flashing
Error (Over temp.) Flashing Steady light
Standby State
(Burn in mode)
Flashing
Burn in (Warming) Flashing
Burn in (Cooling) Flashing
Burn in (Lamp lighting)
Flashing
(3 sec on / 1 sec off)
Burn in (Lamp off)
Flashing
(1 sec on / 3 sec off)
Power off:
Power Off
Power Off?
Press power key again.
English
65
ADDITIONAL INFORMATION
Lamp warning:
Warning
Lamp Warning
Lamp life exceeded.
Temperature warning:
Warning
TEMPERATURE TOO HIGH
Please:
1. Make sure air in and outlets are not blocked.
2. Make sure the environment temperature is under 45 degree C.
If the problem persists in spite of the above.
Please contact a service center for repair.
Fan failed:
Warning
FAN LOCKED
The projector will switch off automatically
Please contact a service center for repair.
Out of display range:
HDMI
Out Of Range
Power down warning:
Power Down
Power Down Timer Active
Power down in sec.
Security timer alarm:
Warning
Security Timer Alarm
Time Out in sec.
English
66
ADDITIONAL INFORMATION
Specications
Optical Description
Maximum resolution
Graphic up to 2160p@60Hz
Maximum Resolution: HDMI1 : 1920*1200@60Hz(RB)
HDMI2 : 2160p@60Hz
Native resolution (w/o actuator) 2716 x 1528
Lens Manual zoom and manual focus
Image size (diagonal)
26.45” ~ 302.2” (Focus range, optimized @ wide 60” image size)
28.89” ~ 300.46” (Focus range, optimized @ wide 60” image size) (for short-
throw lens models)
Projection distance
1.3m ~ 9.3m (Focus range, optimized @ wide 1.846m)
0.5m ~ 5.2m (Focus range, optimized @ wide 1.846m) (for short-throw lens
models)
Electrical Description
Inputs
HDMI 1.4a
HDMI V2.0 HDCP2.2 / MHL 2.1
VGA IN
Audio In 3.5mm
USB2.0 (5V PWR 1.5A)
Outputs
Audio Out 3.5mm
SPDIF Out
12V Trigger (3.5mm jack)
Control
USB Type A (service)
RJ-45 (support web control)
RS232C male (9-pin d-sub)
HDBaseT (only for models with BaseT)
Color reproduction 1073.4 Million color
Scan rate
Horizontal scan rate: 31KHz ~ 135KHz
Vertical scan rate: 24Hz ~ 120Hz
Built-in speaker Yes, 5W
Power requirement 100 - 240V ±10%, AC 50/60Hz
Input current 3.8A-1.0A
Mechanical Description
Installation orientation Front, Rear, Ceiling - Front, Rear - top
Dimensions (W x D x H)
392 x 281.6 x 118.4 mm (without feet)
392 x 281.6 x 129.0 mm (with feet)
Weight 5.3 ± 0.5 kg
Environmental conditions Operating in 5 ~ 40°C , 10% to 85% humidity (non-condensing)
Note: All specications are subject to change without notice.
English
67
ADDITIONAL INFORMATION
Optoma global ofces
For service or support, please contact your local ofce.
USA
47697 Westinghouse Drive, 888-289-6786
Fremont, CA 94539, USA 510-897-8601
www.optomausa.com services@optoma.com
Canada
47697 Westinghouse Drive, 888-289-6786
Fremont, CA 94539, USA 510-897-8601
www.optomausa.com services@optoma.com
Latin America
47697 Westinghouse Drive, 888-289-6786
Fremont, CA 94539, USA 510-897-8601
www.optomausa.com services@optoma.com
Europe
Unit 1, Network 41, Bourne End Mills,
Hemel Hempstead, Herts,
HP1 2UJ, United Kingdom +44 (0) 1923 691 800
www.optoma.eu +44 (0) 1923 691 888
Service Tel : +44 (0)1923 691865 service@tsc-europe.com
Benelux BV
Randstad 22-123 +31 (0) 36 820 0252
1316 BW Almere +31 (0) 36 548 9052
The Netherlands
www.optoma.nl
France
Bâtiment E +33 1 41 46 12 20
81-83 avenue Edouard Vaillant +33 1 41 46 94 35
92100 Boulogne Billancourt, France savoptoma@optoma.fr
Spain
C/ José Hierro,36 Of. 1C +34 91 499 06 06
28522 Rivas VaciaMadrid, +34 91 670 08 32
Spain
Deutschland
Wiesenstrasse 21 W +49 (0) 211 506 6670
D40549 Düsseldorf, +49 (0) 211 506 66799
Germany info@optoma.de
Scandinavia
Lerpeveien 25 +47 32 98 89 90
3040 Drammen +47 32 98 89 99
Norway info@optoma.no
PO.BOX 9515
3038 Drammen
Norway
Korea
WOOMI TECH.CO.,LTD. +82+2+34430004
4F, Minu Bldg.33-14, Kangnam-Ku, +82+2+34430005
Seoul,135-815, KOREA
korea.optoma.com
Japan
東京都足立区綾瀬3-25-18
株式会社オーエス info@os-worldwide.com
コンタクトセンター:0120-380-495 www.os-worldwide.com
Taiwan
12F., No.213, Sec. 3, Beixin Rd., +886-2-8911-8600
Xindian Dist., New Taipei City 231, +886-2-8911-6550
Taiwan, R.O.C. services@optoma.com.tw
www.optoma.com.tw asia.optoma.com
Hong Kong
Unit A, 27/F Dragon Centre,
79 Wing Hong Street, +852-2396-8968
Cheung Sha Wan, +852-2370-1222
Kowloon, Hong Kong www.optoma.com.hk
China
5F, No. 1205, Kaixuan Rd., +86-21-62947376
Changning District +86-21-62947375
Shanghai, 200052, China www.optoma.com.cn
www.optoma.com
*36.7CU01G001-A*
P/N:36.7CU01G001-A
65

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Optoma 4K550 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Optoma 4K550 in de taal/talen: Engels als bijlage per email.

De handleiding is 13,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Optoma 4K550

Optoma 4K550 Gebruiksaanwijzing - Nederlands - 68 pagina's

Optoma 4K550 Gebruiksaanwijzing - Deutsch - 68 pagina's

Optoma 4K550 Gebruiksaanwijzing - Français - 68 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info