645322
87
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
En
AV Receiver
TX-SR603/603E
TX-SR8360
Instruction Manual
Thank you for purchasing an Onkyo AV Receiver.
Please read this manual thoroughly before making
any connections and plugging it in.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver.
Please retain this manual for future reference.
Contents
Introduction ............................... 2
Connections ............................ 21
First Setup ............................... 39
Basic Operations ....................53
Advanced Operations.............64
Advanced Setup......................68
Zone 2 ......................................74
Using the Remote Controller
with Other Components ......78
Specifications.......................... 88
Troubleshooting ...................... 89
2
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radia-
tors, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are pro-
vided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the appara-
tus.
11. Only use attachments/accessories specified by the
manufacturer.
12.
Use only with the cart, stand,
tripod, bracket, or table spec-
ified by the manufacturer, or
sold with the apparatus.
When a cart is used, use cau-
tion when moving the cart/
apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is dam-
aged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous volt-
age points or short-out parts that could result in a
fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and fol-
low local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is ade-
quate ventilation.
Leave 20 cm (8") of free space at the top and sides
and 10 cm (4") at the rear. The rear edge of the shelf
or board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a flue-like
gap for warm air to escape.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated dangerous voltage within
the products enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
AVIS
PORTABLE CART WARNING
S3125A
3
Precautions
For U.S. Models
Note to CATV system installer:
This reminder is provided to call the CATV system
installers attention to Section 820-40 of the NEC which
provides guidelines for proper grounding and, in partic-
ular, species that the cable ground shall be connected
to the grounding system of the building, as close to the
point of cable entry as practical.
FCC Information for User
CAUTION:
The user changes or modications not expressly
approved by the party responsible for compliance could
void the users authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protec-
tion against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a partic-
ular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
For Canadian model
NOTE:
THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION:
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Modèle pour les Canadien
REMARQUE:
CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la che est polarisée:
ATTENTION:
POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND.
1. Recording Copyright
Unless its for personal use
only, recording copyrighted material is illegal with-
out permission of the copyright holder.
2. AC Fuse
The AC fuse inside the AV receiver is
not user-serviceable. If you cannot turn on the AV
receiver, contact your Onkyo dealer.
3. Care
Occasionally you should dust the AV
receiver all over with a soft cloth. For stubborn
stains, use a soft cloth dampened with a weak solu-
tion of mild detergent and water. Dry the AV
receiver immediately afterwards with a clean cloth.
Dont use abrasive cloths, thinners, alcohol, or other
chemical solvents, because they may damage the
nish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the AV receivers rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
Setting the [STANDBY/ON] switch to STANDBY does
not fully shutdown the AV receiver. If you do not intend
to use the AV receiver for an extended period, remove
the power cord from the wall outlet.
For Worldwide model
The Worldwide model has a voltage selector for com-
patibility with power systems around the world. Before
you plug in this model, make sure that the voltage selec-
tor is set to the correct voltage for your area.
If it isnt, use a small screwdriver to set it as appropri-
ate. For example, if the voltage in your area is 120 volts,
set the selector to 120V. And if its between 220 and
230 volts, set it to 220-230V.
CENTER
SPEAKER
FRONT
SPEAKERS
SURROUND
BACK
SPEAKERS
SURROUND
SPEAKERS
FRONT
SURROUND
CENTER
CD
VIDEO 3
VIDEO 3
VIDEO 2
VIDEO 2
VIDEO 1
VIDEO 1
IN
OUT
OUT
ININ
OUT
OUT
TAPE
SUB
WOOFER
MONITOR
OUT
COAXIAL
OPTI
-
CAL
DVD
DVD
ININININ
OUT
OUT
IN IN
R
L
R
L
R
L
IN 1
IN 1
IN 2
IN 1
IN 2IN 3
OUT
COMPONENT VIDEO
REMOTE
CONTROL
IN 2
IN 3
DIGITAL
V
S
P
B
Y
P
R
ZONE 2
SPEAKERS
IR IN
12 V
TRIGGER
OUT
ZONE 2
ANTENNA
FM
75
AM
PRE OUT
ZONE 2
LINEOUT
SUB
WOOFER
R
L
AV RECEIVER
MODEL NO. TX
-
SR
603
L
R
AC OUTLET
SWITCHED
100
W MAX.
120
V
220-240
V
VOLTAG E
SELECTOR
4
Precautions
—Continued
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualied service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
A 5 or 13 ampere fuse is tted in this plug. Should the
fuse need to be replaced, please ensure that the replace-
ment fuse has a rating of 5 or 13 amperes and that it is
approved by ASTA or BSI to BS1362. Check for the
ASTA mark or the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR HOME
THEN THE FUSE SHOULD BE REMOVED AND
THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMPERE SOCKET.
If in any doubt, consult a qualied electrician.
For European Models
This product incorporates copyright protection technol-
ogy that is protected by U.S. patents and other intellec-
tual property rights. Use of this copyright protection
technology must be authorized by Macrovision Corpo-
ration, and is intended for home and other limited con-
sumer uses only unless otherwise authorized by
Macrovision. Reverse engineering or disassembly is
prohibited.
U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098;
4,907,093; 5,315,448; and 6,516,132.
Supplied Accessories
Make sure you have the following accessories:
* In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specications and operations are the
same regardless of color.
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
GROEBENZELL, GERMANY
ONKYO EUROPE ELECTRONICS GmbH
I. MORI
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
Remote controller & three batteries (AA/R6)
Speaker setup microphone
Indoor FM antenna
AM loop antenna
Power-plug adapter
Only supplied in certain countries. Use this adapter if
your AC outlet does not match with the plug on the AV
receiver’s power cord (adapter varies from country to
country).
Speaker cable labels
Front
Left
Front
Left
SP-B
/
Zone 2
Left
SP-B
/
Zone 2
Left
Surround
Right
Surround
Right
Surround Back
Right
Surround Back
Right
Zone 2
Right
Zone 2
Right
Front
Left
Front
Left
SP-B
/
Zone 2
Left
SP-B
/
Zone 2
Left
Front
Right
Front
Right
SP-B
/
Zone 2
Right
SP-B
/
Zone 2
Right
Front
Right
Front
Right
SP-B
/
Zone 2
Right
SP-B
/
Zone 2
Right
Surround
Right
Surround
Right
Center
Center
Center
Center
Surround
Left
Surround
Left
Surround
Left
Surround
Left
Surround Back
Right
Surround Back
Right
Zone 2
Right
Zone 2
Right
Surround Back
Left
Surround Back
Left
Zone 2
Left
Zone 2
Left
Surround Back
Left
Surround Back
Left
Zone 2
Left
Zone 2
Left
1
2
3
Speaker Cable
5
Features
Amplifier
90 watts per channel into 8 ohms, 20 Hz to 20 kHz,
less than 0.08% total harmonic distortion (FTC rating)
7-channel amplier
Optimum Gain Volume Circuitry
Zone 2 capability
24-bit/192 kHz D/A converters
WRAT (Wide Range Amplier Technology)
Color-coded speaker terminal posts
Audio/Video
Dolby
*1
Digital, Dolby Digital EX, Dolby Pro
Logic IIx
DTS
*2
, DTS-ES Discrete, DTS-ES Matrix, DTS
Neo:6, and DTS 96/24
VLSC (Vector Linear Shaping Circuitry) on the front
left and right channels
6 digital inputs (4 optical, 2 coaxial), 1 digital optical
output.
Zone 2 line out
Composite and S-Video to component video conver-
sion
Composite video to S-Video and S-Video to compos-
ite video conversion
3 component video inputs, 1 output
5 S-Video inputs, 3 outputs
CinemaFILTER
*3
Subwoofer pre out
FM/AM Tuner
40 AM/FM presets
AM/FM auto tuning
RDSRadio Data System (Europe only)
Others
Includes microphone for automatic speaker setup
Easy-to-use onscreen setup menus
Preprogrammed remote controller for use with other
AV components
*1. Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks
of Dolby Laboratories.
*2. DTS, DTS 96/24, DTS-ES, and Neo:6 are trademarks
of Digital Theater Systems, Inc.
*3. CinemaFILTER is a trademark of Onkyo Corporation.
Xantech is a registered trademark of Xantech Corporation.
Niles is a registered trademark of Niles Audio Corporation.
6
Table of Contents
Basic
Introduction
Important Safety Instructions..........................................................................................2
Precautions .......................................................................................................................3
Supplied Accessories.......................................................................................................4
Features.............................................................................................................................5
Table of Contents..............................................................................................................6
Front & Rear Panels..........................................................................................................8
Remote Controller...........................................................................................................13
About Home Theater .......................................................................................................20
Connecting the AV Receiver
About AV Connections ...................................................................................................21
Connecting Your Speakers.............................................................................................22
Connecting Antenna.......................................................................................................24
Connecting Your TV or Projector ...................................................................................27
Connecting AV Components .........................................................................................28
Connecting Audio Components....................................................................................34
Connecting Components........................................................................................37
Connecting the Power Cord of Another Component...................................................37
Turning On the AV Receiver...........................................................................................38
First Time Setup
Automatic Speaker Setup...............................................................................................39
About the Onscreen Setup Menus ................................................................................42
Initial Setup......................................................................................................................43
Digital Input ...................................................................................................................43
Component Video Setup ...............................................................................................44
Minimum Speaker Impedance (not North American models) .......................................44
TV Format Setup (not North American models)............................................................45
AM Frequency Step Setup (some models only)............................................................46
Speaker Setup.................................................................................................................46
Changing the TAPE/MD/CDR Display............................................................................52
Basic Operations
Selecting the Input Source.............................................................................................53
Setting the Display Brightness......................................................................................54
Muting the AV Receiver ..................................................................................................54
Using the Sleep Timer.....................................................................................................54
Using Headphones .........................................................................................................54
Displaying Source Information......................................................................................55
Using the Tuner ...............................................................................................................56
Selecting Listening Modes.............................................................................................60
Listening Mode Table.....................................................................................................61
About the Listening Modes............................................................................................62
Others
Specications..................................................................................................................88
Troubleshooting..............................................................................................................89
7
Table of Contents
—Continued
Advanced
Features
Advanced
Features
Advanced
Features
Advanced
Features
Advanced
Controlling Other Components
Entering Remote Control Codes................................................................................... 78
Learning Commands from Another Remote Controller ............................................. 86
Using Macros.................................................................................................................. 87
Advanced Setup
Adjusting the Bass & Treble.......................................................................................... 68
Audio Adjust Functions................................................................................................. 68
Assigning Listening Modes to Input Sources ............................................................. 70
IntelliVolume ...................................................................................................................71
Setting Preferences........................................................................................................ 71
Digital Input Signal Formats ......................................................................................... 72
Changing the Remote Controllers ID........................................................................... 73
Advanced Operations
Using the Late Night Function (Dolby Digital only) .................................................... 64
Using the CinemaFILTER............................................................................................... 64
Adjusting Individual Speaker Levels............................................................................ 65
Using the DVD Analog Multichannel Input .................................................................. 65
Recording........................................................................................................................ 66
Zone 2
Connecting Zone 2......................................................................................................... 74
Setting the Powered Zone 2 .......................................................................................... 75
Using Zone 2................................................................................................................... 76
Using the Remote Control in Zone 2 ............................................................................ 77
8
Front & Rear Panels
The page numbers in parentheses show where you can nd the main explanation for each item.
A
STANDBY/ON button (38)
This button is used to set the AV receiver to On or
Standby.
B
ZONE 2 indicator (76)
This indicator lights up when Zone 2 is selected.
C
ZONE 2/OFF button (76)
The ZONE 2 button is used to select the input
source for Zone 2.
The OFF button is used to turn off the output of
Zone 2.
D
ZONE 2 LEVEL button (76)
This button is used to set the volume for Zone 2.
E
STANDBY indicator (38)
This indicator lights up when the AV receiver is in
Standby mode, and it ashes while a signal is being
received from the remote controller.
F
Remote-control sensor (13)
This sensor receives control signals from the remote
controller.
G
STEREO button (60)
This button is used to select the Stereo listening
mode.
H
LISTENING MODE [ ] [ ] buttons (60)
These buttons are used to select the listening modes.
I
Display
See Display on page 10.
J
DISPLAY button (55)
This button is used to display various information
about the currently selected input source.
K
DIGITAL INPUT button (43, 72)
This button is used to assign the digital inputs and to
specify the format of digital input signals.
L
DIMMER or RT/PTY/TP button (54, 59)
DIMMER is used to adjust the display brightness.
On the European model, this is the RT/PTY/TP but-
ton, and its for RDS (Radio Data System). See
Using RDS (European models only) on page 58.
M
MEMORY button (57)
This button is used when storing or deleting radio
presets.
N
TUNING MODE button (56)
This button is used to select the Auto or Manual tun-
ing mode.
O
RETURN button
This button is used to return to the previously dis-
played onscreen setup menu.
P
Arrow/TUNING/PRESET & ENTER buttons
When the AM or FM input source is selected, the
TUNING [ ] [ ] buttons are used to tune the
tuner, and the PRESET [ ] [ ] buttons are used
to select radio presets (see page 57). When the
onscreen setup menus are used, they work as arrow
buttons and are used to select and set items. The
ENTER button is also used with the onscreen setup
menus.
Front Panel
STANDBY/ON
ZONE2
ZONE 2 LEVEL
PHONES
PURE AUDIO MULTl CH
TONE
+
STEREO
LISTENING MODE
DISPLAY
DIGITAL INPUT
RT/PTY/TP MEMORY
TUNING MODE
RETURN
TUNING / PRESET
ENTER
SETUP
DVD VIDEO 1 VIDEO 2
VCR 1 VCR 2
VIDEO 3 VIDEO 4 TAPE TUNER CD
SETUP MIC S VIDEO VIDEO
MASTER VOLUME
VIDEO 4 INPUT
LR
AUDIO
DIGITAL
OFF
STANDBY
CLEAR
NMLJI K
7 8 0 A B C D F HE G9
1
5
234 6
TX-SR603/603E, TX-SR8360
9
Front & Rear Panels
—Continued
Q
SETUP button
This button is used to access the onscreen setup
menus that appear on the connected TV.
R
MASTER VOLUME control (53)
This control is used to adjust the volume of the AV
receiver to MIN, 1 through 99, or MAX.
S
PHONES jack (54)
This 1/4-inch phone jack is for connecting a stan-
dard pair of stereo headphones for private listening.
T
PURE AUDIO button & indicator (60)
The North American TX-SR603 doesnt have this
button and indicator.
This button is used to select the Pure Audio listen-
ing mode. The indicator lights up when that mode is
selected.
U
TONE, [] & [+] buttons (68)
These buttons are used to adjust the bass and treble.
V
Input selector buttons (53)
These buttons are used to select from the following
input sources: MULTI CH, DVD, VIDEO 1,
VIDEO 2, VIDEO 3, VIDEO 4, TAPE, TUNER or
CD.
The [MULTI CH] button selects the DVD analog
multichannel input.
W
SETUP MIC (39)
The included speaker setup microphone is con-
nected here for automatic speaker setup.
X
VIDEO 4 INPUT
This input can be used to connect a camcorder,
game console, and so on. There are jacks for optical
digital audio, S-Video, composite video, and analog
audio.
10
Front & Rear Panels
—Continued
The page numbers in parentheses show where you can nd the main explanation for each item.
1
MUTING indicator (54)
This indicator ashes while the AV receiver is
muted.
2
ZONE 2 indicator (76)
This indicator lights up when Zone 2 is selected.
3
Listening mode & format indicators
These indicators show the currently selected listen-
ing mode and the format of digital input signals.
4
Tuning indicators (56)
TUNED:
This indicator lights up when the AV
receiver is tuned into a radio station.
AUTO:
This indicator lights up when the Auto Tun-
ing mode is selected, and disappears when the Man-
ual Tuning mode is selected.
RDS (European model only):
This indicator
lights up when the AV Receiver is tuned to a radio
station that supports RDS (Radio Data System).
MEMORY:
This indicator lights up when preset-
ting radio stations.
FM STEREO:
This indicator lights up when the
AV receiver is tuned to a stereo FM station.
5
SLEEP indicator (54)
This indicator lights up when the Sleep function has
been set.
6
Message area
This area of the display shows various information
about the currently selected source.
Display
1 23 4
5
6
11
Front & Rear Panels
—Continued
The page numbers in parentheses show where you can nd the main explanation for each item.
A
OPTICAL DIGITAL
The optical digital audio inputs can be used to con-
nect CD and DVD players, and other components
with an optical digital audio output.
The optical output can be used connect a CD
recorder or other digital recorder with an optical
digital input.
B
COAXIAL DIGITAL
The coaxial digital audio inputs can be used to con-
nect CD and DVD players, and other components
with a coaxial digital audio output.
C
IR IN (77)
If you want to use the remote controller to control
the AV receiver from Zone 2, or if the AV receiver is
installed in a cabinet and the line of sight between
the AV receiver and the remote controller is
obstructed, a commercially available IR receiver
can be connected here.
D
12V TRIGGER OUT ZONE 2 (77)
This output can be connected to the 12-volt trigger
input on a power amplier in Zone 2. When Zone 2
is turned on, a 12-volt trigger signal is output.
E
COMPONENT VIDEO IN 1, 2, 3
These component video inputs can be used to con-
nect AV components with component video outputs,
such as DVD players.
F
COMPONENT VIDEO OUT
This component video output can be used to con-
nect a TV or projector with a component video
input.
G
AM ANTENNA (24)
These push terminals are for connecting an AM
antenna.
H
FM ANTENNA (24)
This jack is for connecting an FM antenna.
I
MONITOR OUT
The S-Video or composite video jack should be
connected to a video input on your TV or projector.
J
ZONE 2 SPEAKERS (74)
These terminal posts are for connecting speakers in
Zone 2.
K
FRONT, CENTER, SURROUND &
SURROUND BACK SPEAKERS (23)
These terminal posts are for connecting your front,
center, surround, and surround back speakers.
Rear Panel
FRONT
SPEAKERS
CENTER
SPEAKER
SURROUND
BACK
SPEAKERS
SURROUND
SPEAKERS
FRONT
SURROUND
CENTER
CD
VIDEO 3
VIDEO 3
VIDEO 2
VIDEO 2
VIDEO 1
VIDEO 1
IN
OUT
OUT
ININ
OUT
OUT
TAPE
SUB
WOOFER
MONITOR
OUT
COAXI AL
OPTI
-
CAL
DVD
DVD
ININININ
OUT
OUT
IN IN
R
L
R
L
R
L
IN 1
IN 1
IN 2
IN 1
IN 2IN 3
OUT
COMPONENT VIDEO
REMOTE
CONTROL
IN 2
IN 3
DIGITAL
V
S
P
B
Y
P
R
ZONE 2
SPEAKERS
IR IN
12 V
TRIGGER
OUT
ZONE 2
ANTENNA
FM
75
AM
PRE OUT
ZONE 2
LINEOUT
SUB
WOOFER
R
L
AV RECEIVER
MODEL NO. TX
-
SR
603E
L
R
120
V
220-240
V
VOLTAGE
SELECTOR
U V
SRQPONM
G
K
9
J
1BCD65L
T
H
TX-SR603/603E, TX-SR8360
See pages 27-37 for connection information.
12
Front & Rear Panels
—Continued
L
VOLTAGE SELECTOR (3)
Certain models only.
This voltage selector provides compatibility with
power systems around the world.
M
REMOTE CONTROL
This (Remote Interactive) jack can be con-
nected to an jack on another Onkyo AV compo-
nent. The AV receivers remote controller can then
be used to control that component. To use , you
must make an analog audio connection (RCA)
between the AV receiver and the other AV compo-
nent, even if they are connected digitally.
N
CD IN
This analog audio input is for connecting a CD
players analog audio output.
O
TAPE IN/OUT
This analog audio input and output are for connect-
ing a recorder with an analog audio input and output
(cassette, Mini Disc, etc.).
P
VIDEO 3 IN
Here you can connect a video source (VCR, set-top
box, etc.). Input jacks include S-Video, composite
video, and analog audio.
Q
VIDEO 2 IN/OUT
Here you can connect a VCR. Input and output
jacks include S-Video, composite video, and analog
audio.
R
VIDEO 1 IN/OUT
Here you can connect a VCR. Input and output
jacks include S-Video, composite video, and analog
audio.
S
DVD IN
Here you can connect a DVD player. Input jacks
include S-Video, composite video, and analog
audio. You can connect a DVD players 2-channel
analog audio output or 5.1-channel analog audio
output.
T
ZONE 2 LINE OUT (74)
This analog audio output can be connected to a line
input on an integrated amplier in Zone 2.
U
PRE OUT (22)
The SUBWOOFER jack is for connecting a pow-
ered subwoofer.
V
AC OUTLET
This switched AC outlet can be used to supply
power to other AV components. The type of outlet
depends on the country in which you purchased
your AV receiver.
See pages 27-37 for connection information.
13
Remote Controller
Notes:
The batteries should last for about six months,
although this will vary with usage.
If the remote controller doesnt work reliably, try
replacing the batteries.
Dont mix new and old batteries or different types of
batteries.
If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
Expired batteries should be removed as soon as possi-
ble to prevent damage from leakage or corrosion.
To use the remote controller, point it at the AV receivers
remote control sensor, as shown below.
Notes:
The remote controller may not work reliably if the AV
receiver is subjected to bright light, such as direct sun-
light or inverter-type uorescent lights. Keep this in
mind when installing.
If another remote controller of the same type is used
in the same room, or the AV receiver is installed close
to equipment that uses infrared rays, the remote con-
troller may not work reliably.
Dont put anything, such as a book, on the remote con-
troller, because the buttons may be pressed inadvert-
ently, thereby draining the batteries.
The remote controller may not work reliably if the AV
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
The remote controller will not work if theres an
obstacle between it and the AV receivers remote con-
trol sensor.
Installing the Batteries
1
To open the battery compartment, press
the small hollow and slide off the cover.
2
Insert the three supplied batteries (AA/R6)
in accordance with the polarity diagram
inside the battery compartment.
3
Put the cover onto the remote controller
and slide it shut.
Using the Remote Controller
30˚
30˚
Approx. 16 ft.
(5 m)
Remote control sensor
AV receiver
14
Remote Controller
—Continued
In addition to controlling the AV receiver, the remote
controller has several operating modes for controlling
your other AV components, including Onkyo compo-
nents connected via . Modes are selected by using
the remote controllers REMOTE MODE buttons.
For detailed information, see the pages in parentheses.
Some of the functions described in this manual may not
work as expected with other components.
Receiver mode is used to control the AV receiver. To
select Receiver mode, press the [RECEIVER] REMOTE
MODE button.
Receiver Mode
8
N
Q
M
L
R
P
9
K
B
A
3
5
6
7
4
J
O
S
RECEIVER
RC-591M
Remote
indicator
This indicator
lights up
when the
remote con-
troller is
transmitting
commands.
No “PURE A”
on RC-590M
15
Remote Controller
—Continued
A
STANDBY button (38)
This button is used to set the AV receiver to
Standby.
B
ON button (38)
This button is used to turn on the AV receiver.
C
INPUT SELECTOR buttons (53)
These buttons are used to select the input source.
D
MULTI CH button (65)
This button is used to select the DVD analog multi-
channel input.
E
REMOTE MODE buttons
These buttons are used to select the remote control-
ler modes.
F
DIMMER button (54)
This button is used to adjust the display brightness.
G
Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons
These buttons are used to select items on the
onscreen setup menus.
H
CH +/ button (57)
This button is used to select radio presets.
I
RETURN button
This button is used to return to the previously dis-
played onscreen setup menu.
J
DISPLAY button (55, 57)
This button is used to display various information
about the currently selected input source.
K
Listening mode buttons (60)
SURR button
This button is used to select the Dolby Digital, Pro
Logic IIx, Neo:6, DTS and other listening modes.
ALL ST button
This button is used to select the All Ch Stereo listen-
ing mode.
STEREO button
This button is used to select the Stereo listening
mode.
PURE A button (RC-591M only)
This button is used to select the Pure Audio listen-
ing mode.
DIRECT button
This button is used to select the Direct listening
mode.
[ DSP] & [DSP ] buttons
These buttons are used to select the Onkyo original
DSP (digital signal processor) listening modes and
Mono listening mode.
L
TEST TONE, CH SEL, LEVEL-, & LEVEL+
buttons (50)
These buttons are used to adjust the level of each
speaker individually. The [LEVEL] & [LEVEL+]
buttons are also used to adjust the volume in
Zone 2.
M
L NIGHT button (64)
This button is used to set the Late Night function.
N
MACRO buttons (87)
These buttons are used with the Macro function.
O
SLEEP button (54)
This button is used to set the Sleep function.
P
VOL button (53)
This button is used to adjust the volume of the AV
receiver.
Q
SETUP button
This button is used to access the onscreen setup
menus that appear on the connected TV.
R
MUTING button (54)
This button is used to mute the AV receiver.
S
CINE FLTR button (64)
This button is used to set the CinemaFILTER func-
tion.
16
Remote Controller
—Continued
DVD mode is used to control an Onkyo DVD player
connected to the AV receiver via .
To set the remote controller to DVD mode, press the
[DVD] REMOTE MODE button.
A
STANDBY button
This button is used to set the DVD player to
Standby.
B
ON button
This button is used to turn on the DVD player and to
set it to Standby.
C
Number buttons
These buttons are used to enter title, chapter, and
track numbers, and to enter times for locating spe-
cic points in time.
D
TOP MENU button
This button is used to select a DVDs top menu.
E
Arrow [ ]/[ ]/[ ]/[ ] & ENTER buttons
These buttons are used to navigate DVD menus and
the DVD players onscreen setup menus.
F
DISC +/ button
This button selects discs on a DVD changer.
G
RETURN/EXIT button
This button is used to exit the DVD players
onscreen setup menu.
H
DISPLAY button
This button is used to display information about the
current disc, title, chapter, or track on the DVD
players display, including the elapsed time, remain-
ing time, total time, and so on.
I
Playback buttons
From left to right: Previous, Play, Next, Fast
Reverse, Pause, Stop, and Fast Forward.
J
Step & Slow [ ]/[ ] buttons
These buttons are used for frame-by-frame play-
back and slow-motion playback.
K
AUDIO button
This button is used to select foreign language
soundtracks and audio formats (e.g., Dolby Digital
or DTS).
L
SUBTITLE button
This button is used to select subtitles.
M
REPEAT button
This button is used to set the repeat playback func-
tions.
6
Q 8
9
0
A
B
1
2
3
4
5
6
7
T
O
P
M
N
K
L
U
S
7
9
J
B
A
3
5
4
8
R
V
W
Y
X
Z
DVD CD
Numbers in circles are for DVD mode.
Numbers in squares are for CD mode.
DVD Mode
17
Remote Controller
—Continued
N
A-B button
This button is used to set the AB repeat playback
function.
O
OPEN/CLOSE [ ] button
This button is used to open and close the disc tray.
P
VIDEO OFF button
This button is used to turn off the internal video cir-
cuitry, eliminating any possibility of interference.
Q
CLEAR button
This button is used to cancel functions and to clear
entered numbers.
R
MENU button
This button is used to display a DVDs menu.
S
VOL button
This button is used to adjust the volume of the AV
receiver.
T
SETUP/GUIDE button
This button is used to access the DVD players
onscreen setup menus.
U
MUTING button
This button is used to mute the AV receiver.
V
RANDOM button
This button is used with the random playback func-
tion.
W
ANGLE button
This button is used to select camera angles.
X
LAST M button
This button is used with the last memory function,
which allows you to resume DVD playback from
where you left off.
Y
SEARCH button
This button is used to search for titles, chapters,
tracks, and specic points in time.
Z
MEMORY button
This button is used with the memory playback func-
tion, which allows you to create a custom playlist of
titles, chapters, or tracks.
CD mode is used to control an Onkyo CD player con-
nected to the AV receiver via .
To set the remote controller to CD mode, press the
[CD] REMOTE MODE button.
1
ON button
This button is used to set the CD player to On or
Standby.
2
Number buttons
These buttons are used to enter track numbers and
to enter times for locating specic points in time.
3
DISC button
This button is used to select discs on a CD changer.
4
DISPLAY button
This button is used to display information about the
current disc or track on the CD players display,
including the elapsed time, remaining time, total
time, and so on.
5
Playback buttons
From left to right: Previous, Play, Next, Fast
Reverse, Pause, Stop, and Fast Forward.
6
REPEAT button
This button is used to set the repeat playback func-
tions.
7
OPEN/CLOSE [ ] button
This button is used to open and close the disc tray.
8
CLEAR button
This button is used to cancel functions and to clear
entered numbers.
9
VOL button
This button is used to adjust the volume of the AV
receiver.
0 MUTING button
This button is used to mute the AV receiver.
A RANDOM button
This button is used with the random playback func-
tion.
B MEMORY button
This button is used with the memory playback func-
tion, which allows you to create a custom playlist of
tracks.
CD Mode
18
Remote Controller
—Continued
MD/CDR mode is used to control an Onkyo MiniDisc
recorder or CD recorder connected to the AV receiver via
.
To select MD/CDR mode, press the [MD/CDR]
REMOTE MODE button.
By default, this button is set to control a MiniDisc
recorder. To control a CD recorder, it must be set to CDR
(see page 78).
A
ON button
This button is used to set the MD recorder or CD
recorder to On or Standby.
B
Number buttons
These buttons are used to enter track numbers and
to enter times for locating specific points in time.
C
DISPLAY button
This button is used to display information about the
current disc or track on the MD recorder or CD
recorder’s display, including the elapsed time,
remaining time, total time, and so on.
D
Play [ ] button
This button is used to start playback.
E
Previous & Next [ ]/[ ] buttons
The Previous [ ] button is used to select the pre-
vious track. During playback it selects the begin-
ning of the current track. The Next [ ] button is
used to select the next track.
F
Pause [ ] button
This button is used to pause playback.
G
REC [ ] button
This button is used to start recording.
H
REPEAT button
This button is used to set the repeat playback func-
tions.
I
OPEN/CLOSE [ ] button
This button is used to eject a MiniDisc or to open
and close the CD recorder’s disc tray.
J
CLEAR button
This button is used to cancel functions and to clear
entered numbers.
K
VOL button
This button is used to adjust the volume of the AV
receiver.
L
MUTING button
This button is used to mute the AV receiver.
J
5
6
7
8
1
2
3
4
9
8
7
L
K
1
2
3
O
P
TAPE MD/CDR
6
M
4
5
N
Numbers in circles are for MD/CDR mode.
Numbers in squares are for TAPE mode.
MD/CDR Mode
19
Remote Controller
—Continued
M
FR & FF [ ]/[ ] buttons
The FR [ ] button is used to start fast reverse. The
FF [ ] button is used to start fast forward.
N
Stop [ ] button
This button is used to stop playback.
O
RANDOM button
This button is used with the random playback func-
tion.
P
MEMORY button
This button is used with the memory playback func-
tion, which allows you to create a custom playlist of
tracks.
TAPE mode is used to control an Onkyo cassette
recorder connected to the AV receiver via .
To set the remote controller to TAPE mode, press the
[TAPE] REMOTE MODE button.
For double cassette decks, only Deck B can be con-
trolled.
1
Play [ ] button
This button is used to start playback.
2
Previous & Next [ ]/[ ] buttons
The Previous [ ] button is used to select the pre-
vious track. During playback it selects the begin-
ning of the current track. The Next [ ] button is
used to select the next track.
The Previous and Next [ ]/[ ] buttons may not
work properly with some cassette tapes depending
on how they were recorded.
3
Reverse Play [ ] button
This button is used to start reverse playback.
4
REC [ ] button
This button is used to start recording.
5
VOL button
This button is used to adjust the volume of the AV
receiver.
6
MUTING button
This button is used to mute the AV receiver.
7
Rewind & FF [ ]/[ ] buttons
The Rewind [ ] button is used to start rewind.
The FF [ ] button is used to start fast forward.
8
Stop [ ] button
This button is used to stop playback.
TAPE Mode
20
About Home Theater
Thanks to the AV receivers superb capabilities, you can enjoy surround sound with a real sense of movement in your
own homejust like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With
analog and digital TV you can enjoy Dolby Pro Logic IIx or Onkyos own DSP surround listening modes.
Enjoying Home Theater
Front left and right speakers
These output the overall sound. Their role in a home theater is to provide a solid
anchor for the sound image. They should be positioned facing the listener at about
ear level, and equidistant from the TV. Angle them inward so as to create a triangle,
with the listener at the apex.
Center speaker
This speaker enhances the front left
and right speakers, making sound
movements distinct and providing a
full sound image. In movies it’s used
mainly for dialog.
Position it close to your TV (preferably
on top) facing forward at about ear
level, or at the same height as the
front left and right speakers.
Subwoofer
The subwoofer handles the bass sounds of
the LFE (Low-Frequency Effects) channel.
The volume and quality of the bass output
from your subwoofer will depend on its posi-
tion, the shape of your listening room, and
your listening position. In general, a good
bass sound can be obtained by installing the
subwoofer in a front corner, or at one-third
the width of the wall, as shown.
Tip: To find the best position for your sub-
woofer, while playing a movie or some
music with good bass, experiment by plac-
ing your subwoofer at various positions
within the room, and choose the one that
provides the most satisfying results.
Surround back left and right speakers
These speakers are necessary to enjoy Dolby Digital EX, DTS-ES
Matrix, and DTS-ES Discrete. They enhance the realism of surround
sound and improve sound localization behind the listener. Position them
behind the listener about 2–3 feet (60–100 cm) above ear level.
Surround left and right
speakers
These speakers are used for
precise sound positioning and
to add realistic ambience.
Position them at the sides of
the listener, or slightly behind,
about 2–3 feet (60–100 cm)
above ear level. Ideally they
should be equidistant from the
listener.
21
Connecting the AV Receiver
Before making any AV connections, read the manuals
supplied with your other AV components.
Dont connect the power cord until youve completed
and double-checked all AV connections.
Optical Digital Jacks
The AV receivers optical digital jacks have shutter-type
covers that open when an optical plug is inserted and
close when its removed. Push plugs in all the way.
Caution:
To prevent shutter damage, hold the optical
plug straight when inserting and removing.
AV Connection Color Coding
RCA-type AV connections are usually color-coded: red,
white, and yellow. Use red plugs to connect right-
channel audio inputs and outputs (typically labeled R).
Use white plugs to connect left-channel audio inputs and
outputs (typically labeled L). And use yellow plugs to
connect composite video inputs and outputs.
Push plugs in all the way to make
good connections (loose connec-
tions can cause noise or malfunc-
tions).
To prevent interference, keep
audio and video cables away from
power cords and speaker cables.
AV Cables & Jacks
Note:
The AV receiver does not support SCART plugs.
About AV Connections
Left (white)
Right (red)
(Yellow)
Analog audio
Composite video
Left (white)
Right (red)
(Yellow)
Right!
Wrong!
Video
Cable Jack Description
Component
video cable
Component video separates the luminance (Y) and
color difference signals (P
R
, P
B
), providing the best
picture quality (some TV manufacturers label their
component video sockets slightly differently).
S-Video cable
S-Video separates the luminance and color signals
and provides better picture quality than composite
video.
Composite
video cable
Composite video is commonly used on TVs, VCRs,
and other video equipment. Use only dedicated
composite video cables.
Audio
Cable Jack Description
Optical digital
audio cable
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for coaxial.
Coaxial digital
audio cable
Offers the best sound quality and allows you to
enjoy surround sound (e.g., Dolby Digital, DTS).
The audio quality is the same as for optical.
Analog audio
cable (RCA)
This cable carries analog audio. Its the most
common connection format for analog audio, and
can be found on virtually all AV components.
Multichannel
analog audio
cable (RCA)
This cable carries multichannel analog audio and
its typically used to connect DVD players with a
5.1-channel analog audio output. Several standard
analog audio cables can be used instead of a multi-
channel cable.
Y
P
B
PR
S
V
OPTICAL
COAXIAL
L
R
22
Connecting the AV Receiver
—Continued
Speaker Configuration
For the best surround sound experience, you should con-
nect seven speakers and a powered subwoofer.
The following table indicates the channels you should
use depending on the number of speakers that you have.
*If youre using only one surround back speaker, connect it to
the left (L) SURROUND BACK SPEAKERS terminals.
No matter how many speakers you use, a powered sub-
woofer is recommended for a really powerful and solid
bass.
To get the best from your surround sound system, you
need to set the speaker settings by using the supplied
setup microphone (see page 39).
Using Dipole Speakers
You can use dipole speakers for the surround left and
right and surround back left and right speakers. Dipole
speakers output the same sound in two directions.
Dipole speakers typically have an arrow printed on them to
indicate how they should be positioned. The surround left
and right
dipole
speakers should be positioned so that their
arrows point toward the TV/screen, while the surround
back left and right dipole speakers should be positioned so
that their arrows point toward each other, as shown.
Connecting a Powered Subwoofer
Using a suitable cable, connect the AV receivers SUB-
WOOFER PRE OUT to an input on your powered sub-
woofer, as shown. If your subwoofer is unpowered and
youre using an external amplier, connect the SUB-
WOOFER PRE OUT to an input on the amp.
Attaching the Speaker Labels
The AV receivers positive (+) speaker terminals are
color-coded for ease of identication (the negative ()
speaker terminals are all black).
The supplied speaker labels are also color-coded and you
should attach them to the positive (+) side of each
speaker cable in accordance with the above table. Then
all you need to do is to match the color of each label to
the corresponding speaker terminal.
Connecting Your Speakers
Number of speakers: 234567
Front left
✓✓✓✓✓✓
Front right
✓✓✓✓✓✓
Center
✓✓✓
Surround left
✓✓✓✓
Surround right
✓✓✓✓
Surround back
Surround back left*
Surround back right*
2
1
3
4
2
1
3
4
5
7 8
6
5
6
78
TV/screen
TV/screen
1. Subwoofer
2. Front left speaker
3. Center speaker
4. Front right speaker
5. Surround left speaker
6. Surround right speaker
7. Surround back left
speaker
8. Surround back right
speaker
Dipole speakers
Normal speakers
Speaker terminal Color
Front left, Zone 2 left White
Front right, Zone 2 right Red
Center Green
Surround left Blue
Surround right Gray
Surround back left Brown
Surround back right Tan
SURROUND
BACK
SPEAKERS
FRONT
SURROUND
CENTER
CD
VIDEO 3
VIDEO 3
VIDEO 2
VIDEO 2
VIDEO 1
VIDEO 1
IN
OUT
OUT
ININ
OUT
OUT
TAPE
SUB
WOOFER
MONITOR
OUT
COAXIAL
OPTI
-
CAL
DVD
DVD
ININININ
OUT
OUT
IN IN
R
L
R
L
IN 1
IN 1
IN 2
IN 1
IN 2IN 3
OUT
COMPONENT VIDEO
REMOTE
CONTROL
IN 2
IN 3
DIGITAL
V
S
P
B
Y
P
R
ZONE 2
SPEAKERS
IR IN
12 V
TRIGGER
OUT
ZONE 2
ANTENNA
FM
75
AM
PRE OUT
ZONE 2
LINEOUT
SUB
WOOFER
R
L
AV RECEIVER
MODEL NO. TX
-
SR
603E
L
R
PRE OUT
SUB
WOOFER
LINE INPUT
LINE INPUT
Powered
subwoofer
23
Connecting the AV Receiver
—Continued
Speaker Connection Precautions
Read the following before connecting your speakers:
North American model only:
Only connect speakers
with an impedance of 6 ohms or higher. If you use
speakers with a lower impedance, and use the ampli-
er at high volume levels for a long period of time, the
built-in protection circuit may be activated.
Other models:
You can connect speakers with an
impedance of between 4 and 16 ohms. If the imped-
ance of any of the connected speakers is 4 ohms or
more, but less than 6 ohms, be sure to set the Mini-
mum Speaker Impedance to 4 ohms (see page 44).
If you use speakers with a lower impedance, and use
the amplier at high volume levels for a long period of
time, the built-in protection circuit may be activated.
Disconnect the power cord from the wall outlet before
making any connections.
Read the instructions supplied with your speakers.
Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive
(+) terminals, and negative () terminals only to nega-
tive () terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
If you use 4 or 5 speakers, connect each of the two
surround speakers to the SURROUND SPEAKERS
terminals. Do not connect them to the SURROUND
BACK SPEAKERS terminals.
Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver.
Make sure the metal core of the
wire does not have contact with
the TX-SR603/603E/8360s
rear panel. Doing so may dam-
age the AV receiver.
Dont connect more than one cable to each speaker
terminal. Doing so may damage the AV receiver.
Dont connect one speaker to several terminals.
Connecting the Speaker Cables
The following illustration shows which speaker should
be connected to each pair of terminals.
If youre using only one surround back speaker, connect
it to the left (L) SURROUND BACK SPEAKERS termi-
nals.
1
Strip about 5/8" (15 mm)
of insulation from the
ends of the speaker
cables, and twist the bare
wires tightly, as shown.
2
Unscrew the terminal.
3
Fully insert the bare
wires.
4
Screw the terminal tight.
5/8" (15 mm)
FRONT
SPEAKERS
CENTER
SPEAKER
SURROUND
BACK
SPEAKERS
SURROUND
SPEAKERS
R
L
R
L
Surround
back left
speaker
Surround
back right
speaker
Center
speaker
Front left
speaker
Front right
speaker
Surround
right
speaker
Surround
left
speaker
24
Connecting the AV Receiver
—Continued
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The AV receiver wont pick up any radio signals without
any antenna connected, so you must connect the antenna
to use the tuner.
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead (see page 25).
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commer-
cially available outdoor AM antenna (see page 25).
Connecting Antenna
1
Attach the FM antenna, as shown.
North American Model
Other Models
Once your AV receiver is ready for use, youll
need to tune into an FM radio station and adjust
the position of the FM antenna to achieve the best
possible reception.
2
Use thumbtacks or something similar to
x the FM antenna into position.
Caution:
Be careful that you dont injure yourself
when using thumbtacks.
FRONT
SPEAKERS
CENTER
SPEAKER
SURROUND
BACK
SPEAKERS
SURROUND
SPEAKERS
FRONT
SURROUND
CENTER
CD
VIDEO 3
VIDEO 3
VIDEO 2
VIDEO 2
VIDEO 1
VIDEO 1
IN
OUT
OUT
ININ
OUT
OUT
TAPE
SUB
WOOFER
MONITOR
OUT
COAXIAL
OPTI
-
CAL
DVD
DVD
ININININ
OUT
OUT
IN IN
R
L
R
L
R
L
IN 1
IN 1
IN 2
IN 1
IN 2IN 3
OUT
COMPONENT VIDEO
REMOTE
CONTROL
IN 2
IN 3
DIGITAL
V
S
P
B
Y
P
R
ZONE 2
SPEAKERS
IR IN
12 V
TRIGGER
OUT
ZONE 2
ANTENNA
FM
75AM
PRE OUT
ZONE 2
LINEOUT
SUB
WOOFER
R
L
AV RECEIVER
MODEL NO. TX
-
SR
603E
L
R
AM antenna push terminals
FM antenna connector
Insert the plug fully
into the jack.
Insert the plug fully
into the jack.
Thumbtacks, etc.
1
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
2
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
(The antennas wires are not polarity sensitive, so
they can be connected either way around).
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
Once your AV receiver is ready for use, youll
need to tune into an AM radio station and adjust
the position of the AM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from
your AV receiver, TV, speaker cables, and power
cords.
Push Insert wire Release
25
Connecting the AV Receiver
—Continued
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead.
Notes:
Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in
an attic or loft.
For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
Using a TV/FM Antenna Splitter
Its best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If cir-
cumstances demand it, use a TV/FM antenna splitter, as
shown.
Connecting an Outdoor AM Antenna
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor AM antennas work best when installed outside
horizontally, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
To AV receiver To TV (or VCR)
TV/FM antenna splitter
Outdoor antenna
AM loop antenna
Insulated antenna cable
26
Connecting the AV Receiver
—Continued
By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you
can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV receiver.
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format
you choose will depend on the formats supported by your other components. Use the following sections as a guide.
For video components, you must make two connectionsone for audio, one for video.
Video Connection Formats
Video equipment can be connected to the AV receiver by
using any one of the following video connection for-
mats: composite video, S-Video, or component video,
the latter offering the best picture quality.
A video signal connected to a V or S IN jack will be
convertedcomposite video to S-Video or S-Video to
composite videobut only for the MONITOR OUT
jacks, not the VIDEO 1 and VIDEO 2 OUT V and S
jacks.
Note:
The TX-SR603/603E/8360 can be set to upcon-
vert composite video and S-Video input signals and
output them from the COMPONENT VIDEO OUT (see
page 44).
Audio Connection Formats
Audio equipment can be connected to the AV receiver by
using any of the following audio connection formats:
analog, optical, coaxial, or multichannel.
When choosing a connection format, bear in mind that
the AV receiver doesnt convert between them. For
example, audio signals connected to an OPTICAL or
COAXIAL input are not output by the analog TAPE
OUT.
Connecting Both Audio & Video
: Signal Flow
Video
Audio
Video
Audio
Speakers (see page 23 for connection infor-
mation)
DVD player, etc.
TV, projector,
etc.
Which Connections Should I Use?
DVD player,
etc.
AV Receiver
TV, pro-
jector,
etc.
Composite
Output
IN
MONITOR OUT
Input
Composite
Composite
Composite
S-Video
S-Video
S-Video
S-Video
Component
Component
Component
Component
page 44
DVD player,
etc.
AV Receiver
MD recorder,
etc.
Optical
Output
IN
OUT
Input
Optical
Optical
Coaxial
Coaxial
Analog
Analog
Analog
Multi-
channel
Multi-
channel
Only front
left and
right
Optical
Analog
27
Connecting the AV Receiver
—Continued
Monitor Out
Using Composite Video
Use a composite video cable to connect the AV
receivers V MONITOR OUT jack to a composite video
input on your TV, as shown.
Using S-Video
Use an S-Video cable to connect the AV receivers
S MONITOR OUT jack to an S-Video input on your TV,
as shown.
Using Component Video
Use a component video cable to connect the AV
receivers COMPONENT VIDEO OUT jacks to a com-
ponent video input on your TV, as shown.
Audio Connections
These connections will allow you to listen to audio from
your TV via the AV receiver.
If your TV doesnt have an audio output, connect the AV
receiver to your VCR and use its tuner (see page 30).
Using Coaxial or Optical Connections
If you connect to a digital audio input, youll need to
assign it (see page 43).
Use an optical digital audio cable to connect one of the
AV receivers OPTICAL DIGITAL IN jacks to an
optical output on your TV, as shown.
OR
Use a coaxial digital audio cable to connect one of the
AV receivers COAXIAL DIGITAL IN jacks to a
coaxial output on your TV, as shown.
Using Analog Connections
If your TV doesnt have a digital audio output, or you
want to record from it, youll need to make the following
analog audio connection.
Use an analog audio cable to connect the AV receivers
VIDEO 3 IN L/R jacks to an analog audio output on
your TV, as shown.
Connecting Your TV or Projector
TV, projector,
etc.
MONITOR
OUT
S
S VIDEO IN
TV, projector,
etc.
YPB PR
COMPONENT
VIDEO IN
P
COMPONENT VIDEO
B
PR
Y
TV, projector,
etc.
OPTI-
CAL
IN
COAXIAL
IN 2
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
TV, projector,
etc.
Connect one or the
other
IN
VIDEO 3
AUDIO
OUTPUT
L
R
TV, projector,
etc.
28
Connecting the AV Receiver
—Continued
Video Connections
You only need to use one of the following connection
methods.
Using Composite Video
Use a composite video cable to connect the AV
receiver’s V DVD IN jack to the composite video output
on your DVD player, as shown.
Using S-Video
Use an S-Video cable to connect the AV receiver’s
S DVD IN jack to the S-Video output on your DVD
player, as shown.
Using Component Video
Use a component video cable to connect the AV
receiver’s COMPONENT VIDEO IN1 jacks to the com-
ponent video output on your DVD player, as shown.
Your TV must also be connected via component video.
Audio Connections
Using Coaxial or Optical Connections
Use a coaxial digital audio cable to connect one of the
AV receiver’s COAXIAL DIGITAL IN jacks to the
coaxial output on your DVD player, as shown.
OR
Use an optical digital audio cable to connect one of the
AV receiver’s OPTICAL DIGITAL IN jacks to the
optical output on your DVD player, as shown.
Initially, the COAXIAL IN 1 jack is assigned to the
DVD input source. If you connect your DVD player to a
different digital input, you’ll need to reassign the DVD
input source (see page 43).
Using Analog Connections
Even if your DVD player is connected digitally (optical
or coaxial), to use , or to record audio from your
DVD player, you’ll need to make an analog connection
as well.
Use an analog audio cable to connect the AV receiver’s
DVD IN L/R jacks to the analog audio output on your
DVD player, as shown.
If your DVD player has stereo (L/R) and multichannel
outputs, be sure to use the left and right outputs.
Connecting a DVD Player
VIDEO OUT
IN
DVD
DVD player
S VIDEO OUT
DVD
IN
DVD player
COMPONENT
VIDEO OUT
COMPONENT VIDEO
IN 1
Y
P
B
PR
YPB PR
DVD player
DIGITAL
IN 1
COAXIAL
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
OPTI-
CAL
IN
Connect one or the other
DVD player
LR
AUDIO
OUTPUT
L
R
DVD
FRONT
DVD player
29
Connecting the AV Receiver
—Continued
Using a Multichannel Connection
If your DVD player supports multichannel audio formats
such as DVD-Audio, and it has a 5.1-channel analog
audio output, you can enjoy DVD-Audio playback.
Use a multichannel analog audio cable to connect the AV
receivers DVD IN FRONT L/R, CENTER, SUR-
ROUND L/R, and SUBWOOFER jacks to the 5.1-
channel analog audio output on your DVD player, as
shown. Alternatively, use several analog audio cables.
DVD player
30
Connecting the AV Receiver
—Continued
This section shows how to connect a VCR for playback
so that you can watch videos via the AV receiver.
Video Connections
Use an S-Video cable to connect the AV receiver’s
S VIDEO 1 IN jack to a S-Video output on your VCR,
as shown.
OR
Use a composite video cable to connect the AV
receiver’s V VIDEO 1 IN jack to a composite video
output on your VCR, as shown.
An S-Video connection provides better picture quality
than a composite video connection.
Audio Connections
Use an analog audio cable to connect the AV
receiver’s VIDEO 1 IN L/R jacks to an analog audio
output on your VCR, as shown.
Video Connections
With the initial settings of the TX-SR603/603E/8360,
the VIDEO 1 input source is set for the COMPONENT
VIDEO IN 2 jacks. If you connect the device to the
COMPONENT VIDEO IN 3 jacks, see page 44.
Use a component video cable to connect the AV receiver’s
COMPONENT VIDEO IN2 or 3 jacks to a component
video output on your HDD/DVD recorder, as shown.
Your TV must also be connected via component video.
Audio Connections
If you connect to a digital audio input, you'll need to
assign it (see page 43).
Use an optical digital audio cable to connect one of the
AV receiver’s OPTICAL DIGITAL IN jacks to an
optical output on your HDD/DVD recorder, as shown.
OR
Use a coaxial digital audio cable to connect one of the
AV receiver’s COAXIAL DIGITAL IN jacks to a
coaxial output on your HDD/DVD recorder, as shown.
Connecting a VCR for Playback
VIDEO 1
LR
S VIDEO OUT
VIDEO OUT
AUDIO
OUTPUT
IN
IN
L
R
VCR
Connect one
or the other
Connecting an HDD/DVD recorder for
Playback
IN
Y
P
B
PR
COMPONENT
VIDEO OUT
COMPONENT VIDEO
Y
P
B
PR
HDD/DVD recorder
DIGITAL
IN 2
COAXIAL
OPTI-
CAL
IN
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
HDD/DVD
recorder
Connect one or the other
31
Connecting the AV Receiver
—Continued
This section explains how to connect a VCR for
recording from a TV or another VCR.
Video Connections
Use an S-Video cable to connect the AV receivers
S VIDEO 1 OUT jack to an S-Video input on the
recording VCR. Use another S-Video cable to connect
the AV receivers S VIDEO 3 IN jack to an S-Video
output on your TV or playback VCR, as shown.
OR
Use a composite video cable to connect the AV
receivers V VIDEO 1 OUT jack to a composite video
input on the recording VCR. Use another composite
video cable to connect the AV receivers V VIDEO 3
IN jack to a composite video output on your TV or
playback VCR, as shown.
Audio Connections
Use an analog audio cable to connect the AV
receivers VIDEO 1 OUT L/R jacks to an audio input
on the recording VCR.
Use an analog audio cable to connect the AV
receivers VIDEO 3 IN L/R jacks to an audio output
on your TV or playback VCR.
Playback from the Recording VCR
To play back a video in the recording VCR via the AV
receiver:
Use an S-Video cable to connect the AV receivers S
VIDEO 1 IN jack to an S-Video output on the record-
ing VCR.
OR
Use a composite video cable to connect the AV
receivers V VIDEO 1 IN jack to a composite video
output on the recording VCR.
And use an analog audio cable to connect the AV
receivers VIDEO 1 IN L/R jacks to an audio output on
the recording VCR.
Notes:
The AV receiver must be turned on for recording.
Recording is not possible while its in Standby mode.
If you want to record directly from your TV or play-
back VCR to the recording VCR without going
through the AV receiver, connect the TV/VCRs audio
and video outputs directly to the recording VCRs
audio and video inputs. See the manuals supplied with
your TV and VCR for details.
Video signals connected to composite video inputs
can only be recorded via composite video outputs. If
your TV/VCR is connected to a composite video
input, the recording VCR must be connected to a com-
posite video output. Similarly, video signals con-
nected to S-Video inputs can only be recorded via
S-Video outputs. If your TV/VCR is connected to an
S-Video input, the recording VCR must be connected
to an S-Video output.
Connecting a VCR for Recording
VIDEO
OUT
S VIDEO
OUT
LR
AUDIO
OUTPUT
LR
S VIDEO IN
VIDEO IN
AUDIO
INPUT
LR
S VIDEO OUT
VIDEO OUT
AUDIO
OUTPUT
L
R
IN
IN
VIDEO 3
OUT
OUT
VIDEO 1
IN
IN
:
:
TV
VCR (recording)
Connect one
or the other
Connect one or
the other
For recording
For playback
VCR, etc.or
32
Connecting the AV Receiver
—Continued
Video Connections
You only need to use one of the following connection
methods.
Using Composite Video
Use a composite video cable to connect the AV
receiver’s V VIDEO 3 IN jack to a composite video
output on your video source, as shown.
Using S-Video
Use an S-Video cable to connect the AV receiver’s
S VIDEO 3 IN jack to an S-Video output on your video
source, as shown.
Using Component Video
If you connect to a component video input, you must
assign it (see page 44).
Use a component video cable to connect the AV
receiver’s COMPONENT VIDEO IN 2 or IN 3 jack to a
component video output on your video source, as shown.
Audio Connections
Using Optical or Coaxial Connections
If you connect to a digital audio input, you’ll need to
assign it (see page 43).
Use an optical digital audio cable to connect one of the
AV receiver’s OPTICAL DIGITAL IN jacks to an
optical output on your video source, as shown.
OR
Use a coaxial digital audio cable to connect one of the
AV receiver’s COAXIAL DIGITAL IN jacks to a
coaxial output on your video source, as shown.
Note:
To connect the AV receiver to an LD player’s AC-3RF
output, you need a commercially available demodulator.
Connecting Other Video Sources—
Satellite, Cable, Set-top box, LD
Player, etc.
IN
VIDEO 3
VIDEO OUT
Satellite, cable, set-top
box, LD player, etc.
VIDEO 3
IN
S VIDEO OUT
Satellite, cable, set-top
box, LD player, etc.
COMPONENT
VIDEO OUT
Y
P
B
PR
IN
Y
P
B
PR
COMPONENT VIDEO
Satellite, cable, set-top
box, LD player, etc.
DIGITAL
IN 2
COAXIAL
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
OPTI-
CAL
IN
Satellite, cable, set-top box, LD player, etc.
Connect one or the other
33
Connecting the AV Receiver
—Continued
Using Analog Connections
If your video source doesnt have a digital audio output,
or you want to record from it, youll need to make the
following analog audio connection.
Use an analog audio cable to connect the AV receivers
VIDEO 3 IN L/R jacks to the analog audio output on
your video source, as shown.
Video Connections
You only need to use one of the following connection
methods.
Using Composite Video
Use a composite video cable to connect the AV
receivers VIDEO 4 INPUT VIDEO jack to the com-
posite video output on your camcorder, game console,
etc., as shown.
Using S-Video
Use an S-Video cable to connect the AV receivers
VIDEO 4 INPUT S VIDEO jack to the S-Video output
on your camcorder, game console, etc., as shown.
Audio Connections
Use an analog audio cable to connect the AV receivers
VIDEO 4 INPUT AUDIO L/R jacks to the analog audio
output on your camcorder, game console, etc., as shown.
If your camcorder, game console, etc., has an optical dig-
ital audio output, use an optical digital audio cable to
connect it to the AV receivers VIDEO 4 INPUT DIG-
ITAL jack, as shown.
Connecting a Camcorder, Game
Console, etc.
LR
L
R
AUDIO
OUTPUT
IN
VIDEO 3
Satellite, cable, set-top
box, LD player, etc.
VIDEO OUT
VIDEO
Camcorder,
game console, etc.
S VIDEO OUT S VIDEO
Camcorder,
game console, etc.
AUDIO
LR
L
R
AUDIO
OUTPUT
Camcorder,
game console, etc.
DIGITAL OUT
DIGITAL
Camcorder,
game console, etc.
34
Connecting the AV Receiver
—Continued
Using Optical or Coaxial Connections
If you connect to a digital audio input, youll need to
assign it (see page 43).
Use an optical digital audio cable to connect one of the
AV receivers OPTICAL DIGITAL IN jacks to the
optical output on your CD player, as shown.
OR
Use a coaxial digital audio cable to connect one of the
AV receivers COAXIAL DIGITAL IN jacks to the
coaxial output on your CD player, as shown.
Using Analog Connections
Even if your CD player is connected digitally (coaxial or
optical), to use , or to record audio from your CD
player, youll need to make an analog audio connection
as well.
Use an analog audio cable to connect the AV receivers
CD IN L/R jacks to the analog audio output on your CD
player, as shown.
Use an analog audio cable to connect the AV receivers
TAPE IN L/R jacks to the cassette recorders output, and
use another analog audio cable to connect the AV
receivers TAPE OUT L/R jacks to the cassette
recorders input, as shown.
You can connect a DAT, CD, or MD recorder instead of
a cassette recorder.
Analog Connections
Use an analog audio cable to connect the AV receivers
TAPE IN L/R jacks to the recorders output, and use
another analog audio cable to connect the AV receivers
TAPE OUT L/R jacks to the recorders input, as shown.
Connecting a CD Player
DIGITAL
IN 2
COAXIAL
OPTI-
CAL
IN
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
CD player
Connect one or the other
IN
CD
AUDIO
OUTPUT
L
R
CD player
Connecting a Cassette Recorder
Connecting a DAT, CD, or MD
Recorder
/
OUT
TAPE
R
L
R
L
R
L
R
L
IN
(IN) (OUT)
REC PLAY
Cassette recorder
OUT
TAPE
R
L
R
L
R
L
R
L
IN
(IN) (OUT)
REC PLAY
DAT, CD, or MD recorder
35
Connecting the AV Receiver
—Continued
Using Optical or Coaxial Connections
(playback only)
If you connect to a digital audio input, youll need to
assign it (see page 43).
Use an optical digital audio cable to connect one of the
AV receivers OPTICAL DIGITAL IN jacks to the
optical output on your recorder, as shown.
OR
Use a coaxial digital audio cable to connect one of the
AV receivers COAXIAL DIGITAL IN jacks to the
coaxial output on your recorder, as shown.
Digital Recording
If your recorder has a digital input, by connecting it to
the AV receivers optical DIGITAL OUT jack, you can
record digitally. However, because the AV receiver
doesnt convert analog input signals to digital and vice
versa, only input signals connected to a DIGITAL IN
jack can be recorded in this way.
DIGITAL
IN 2
COAXIAL
DIGITAL OUT
OPTICAL
DIGITAL OUT
COAXIAL
OPTI-
CAL
IN
DAT, CD, or MD
recorder
Connect one or the other
DIGITAL
IN 2
COAXIAL
OPTICAL
DIGITAL OUT
COAXIAL
DIGITAL OUT
OPTICAL
DIGITAL IN
OPTI-
CAL
IN
OPTI-
CAL
DAT, CD, or MD recorder
Digital source (DAT, CD, MD player)
Connect one or the other
36
Connecting the AV Receiver
—Continued
Turntable with a Built-in Phono Preamp
Use an analog audio cable to connect an unused audio
input on the AV receiver to the audio outputs on your
turntable, as shown.
Turntable without a Built-in Phono Preamp
Use an analog audio cable to connect an unused audio
input on the AV receiver to the audio outputs on your
phono preamp, and use another analog audio cable to
connect the phono preamps inputs to your turntable, as
shown.
Turntable with an MC (Moving Coil) Cartridge
Use an analog audio cable to connect an unused audio
input on the AV receiver to the audio outputs on your
phono preamp. Use another analog audio cable to con-
nect the phono preamps inputs to your MC head amps
outputs. And use another analog audio cable to connect
the MC head amps inputs to your turntable, as shown.
For further information, see the manual for your turnta-
ble or phono preamp.
Connecting a Turntable
IN
L
R
CD
AUDIO
OUTPUT
L
R
L
R
L
R
IN
CD
AUDIO
OUTPUT
AUDIO
OUTPUT
AUDIO
INPUT
Phono preamp
L
R
L
R
L
R
L
R
IN
CD
AUDIO
OUTPUT
AUDIO
OUTPUT
AUDIO
INPUT
AUDIO
INPUT
Phono preamp
MC head amp or
MC transformer
37
Connecting the AV Receiver
—Continued
With (Remote Interactive) you can control your
-compatible Onkyo CD player, DVD player, and so
on with the AV receivers remote controller, as follows:
To use , you must make an analog audio con-
nection between the AV receiver and the other AV
components, even if they are connected digitally.
Auto Power On/Standby
When you start playback on an AV component con-
nected via , if the AV receiver is in Standby, it will
turn on and select that AV component as the input source
automatically. Similarly, when the AV receiver is set to
Standby, all components connected via also enter
Standby. Note that this function will not work if the com-
ponents power cord is connected to the AV receivers
AC OUTLET.
Direct Change
When playback is started on an AV component con-
nected via , the AV receiver automatically selects
that AV component as the input source.
Remote Control
You can control your -compatible Onkyo compo-
nents with the AV receivers remote controller.
Notes:
If you connect an -compatible Onkyo MiniDisc
recorder or CD recorder to the TAPE IN/OUT jacks,
for to work properly, you must change the
TAPE/MD/CDR display (see page 52).
Push plugs in all the way to make good connections.
Use only cables for connections. No
cables are supplied with this AV receiver.
Some AV components have two jacks. You can
connect either one to this AV receiver. The other jack
is for connecting more -compatible components.
Connect the AV receivers jack to only Onkyo AV
components. Connecting to other manufacturers AV
components may cause them to malfunction.
Some components may not support all functions.
Refer to the manuals supplied with your components.
The AV receiver has an AC outlet on its rear panel for
connecting the power cord of another AV component.
The other components power switch can then be left in
the ON position so that it turns on or off when the AV
receiver is set to On or Standby.
Caution:
Make sure that the capacity of the component that you
connect to the AC OUTLET does not exceed the stated
capacity (e.g., 100 W).
Notes:
Onkyo components with jacks should be con-
nected directly to wall outlets, not the AV receivers
AC OUTLET.
The socket type and capacity will depend on the coun-
try in which you purchased the AV receiver.
Connecting Components
REMOTE
CONTROL
L
R
IN
L
R
L
R
AUDIO
OUTPUT
AUDIO
OUTPUT
L
R
IN
e.g., DVD player
e.g., MD recorder
Connecting the Power Cord of
Another Component
AC OUTLET
AC
120
V 60
Hz
SWITCHED
120W 1A MAX.
European and some
Asian models
North American
model
38
Connecting the AV Receiver
—Continued
Before connecting the power cord, connect all your
speakers and AV components.
Turning on the AV receiver may cause a momentary
power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem,
plug the AV receiver into a different circuit.
Notes:
Pressing the remote controllers [ON] button once will
turn on the AV receiver. Pressing it again will turn on
any components connected via .
When the AV receiver is on Standby, it will turn on
automatically when any one of its input selector but-
tons is pressed.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to Standby.
Turning On the AV Receiver
1
Plug the power cord into an AC
wall outlet.
The STANDBY indicator will light up.
2
Press the [STANDBY/ON] button.
Alternatively, press the remote
controllers [RECEIVER] button
followed by the [ON] button.
The AV receiver comes on, the display
lights up, and the STANDBY indicator
goes off.
To turn off the AV receiver, press the
[STANDBY/ON] button. The AV
receiver will enter Standby mode.
STANDBY/ON
STANDBY
ON
To wall outlet
STANDBY indicator
STANDBY
STANDBY/ON
STANDBY
ON
Remote
controller
39
First Time Setup
This chapter explains the settings that you need to make before using the AV receiver.
With the supplied speaker setup microphone, the Auto-
matic Speaker Setup function can measure the test tone
output by each speaker and automatically determine the
number of speakers connected, their sizes, the distance
from each speaker to the listening position, and so on.
Before using this function, connect and position all your
speakers.
Automatic Speaker Setup
1
Turn on the AV receiver and the
connected TV.
On the TV, select the input to which the
AV receiver is connected.
37
2
1
2
Put the speaker setup micro-
phone in the listening position,
and connect it to the SETUP MIC
jack.
Notes:
Make sure the microphone is hori-
zontal.
If theres an obstacle between the
microphone and any speaker, the
automatic setup will not work cor-
rectly. Setup the room as you would
when enjoying a DVD.
If the AV receiver was previously
muted, the Muting function will be
cancelled.
The automatic setup cannot be used
while a pair of headphones is con-
nected.
By putting the microphone close to
where your ears would normally be
at the listening position, a more accu-
rate setup can be achieved. If you use
a tripod or level table, you can adjust
the height of the microphone.
MIC
position
40
First Time Setup
—Continued
How to Verify the Measurement Results
By selecting Check the Results at step 4, you can dis-
play the following screen to conrm the measurement
results.
3
Press [ENTER].
The automatic speaker setup starts.
The test tone is output by each speaker
in turn, measured by the microphone,
and the speaker settings set accordingly.
The whole process takes about 2 minutes.
If any extraneous noise is picked up by
the microphone, the automatic setup
may not work correctly, so be careful.
4
Once the measurement is com-
pleted, the following completion
screen appears.
Use the Up and Down [ ]/[ ]
buttons to select any of the fol-
lowing options, and then press
[ENTER].
Apply the Results:
Validates the measurement results and
closes the screen. Normally you may
want to select this option. Continue
with step 5.
Check the Results:
Displays the measurement results for
your reference. Continue with How to
Verify the Measurement Results
described below.
Retry:
Retries measurement. Return to step 2.
Retry with Test noise Level up:
Retries measurement with the test
sound at high volume level. Return to
step 2.
Cancel:
Closes the screen without validating
the measurement results. Continue with
step 5.
ENTER
ENTER
ENTER
5
Disconnect the speaker setup
microphone.
To cancel the automatic setup while its
in progress, disconnect the micro-
phone.
Use the Up and Down [ ]/[ ]
buttons to select the item that
you want to check, and then
press [ENTER].
Press the [RETURN] button to return to
the previous display.
ENTER
ENTER
1 Warning
2 Number of speakers and their sizes
3 Distance from each speaker to the
listening position
4 The optimum volume level for each
speaker
5 The level adjustment for individual
frequency range covered by
respective speaker
41
First Time Setup
—Continued
Note:
Measurement may not be performed correctly depend-
ing on your use environment. If the measurement results
remain unchanged after retried, create speaker settings
manually (see pages 46-51).
Tip:
When any amplier-builtin subwoofer is connected, its
sound may not be detected with the automatic speaker
settings because the sound is generated from the low
position with very low frequencies. If the subwoofer
(SW) is specied as Not Detect in the measurement
results conrmation screen, turn the volume up to an
appropriate level and the frequency as high as it can go.
And then turn on the Direct switch, if available. For fur-
ther information, see the manual for the subwoofer.
(Menus vary depending on country)
*
When a speaker has a warning, its abbrevia-
tion (e.g., L, R, and so on) appears.
Not Detect:
No speaker was detected. Make sure
the connection is secured correctly.
Distance Error:
The positions of the speakers are too
close or too far, or the distance could
not be measured.
If you want to adjust any of the settings
manually, see Speaker Setup on
page 46.
When youve checked the set-
tings, press the [RETURN] button
to return to the previous menu.
*
42
First Time Setup
—Continued
The AV receiver is congured using onscreen setup menus, which are displayed on the TV thats connected to either of
the MONITOR OUT jacks. Because they appear on your TV, theyre large and clear, making setup a breeze.
About the Onscreen Setup Menus
*
Main menu
Submenus
p. 46
p. 44
p. 43
p. 49
p. 50
p. 51
p. 70
p. 46
p. 68
p. 71
* For multichannel connection, “3. Multich
Level Adjust” appears instead of “3. Level
Calibration.
43
First Time Setup
—Continued
Digital Input
If you connect a component to a digital input jack, you
must assign that jack to an input selector. For example,
if you connect your CD player to the OPTICAL IN2
jack, you should assign that jack to the CD input selec-
tor. By default, the COAXIAL IN1 jack is assigned to
the DVD input selector, although this can be changed.
Initial Setup
1
Press the input selector button
for the source that you want to
assign.
(Digital inputs cannot be assigned to
the TUNER input source)
2
Press the [DIGITAL INPUT] but-
ton.
The current assignment appears.
3
Press the [DIGITAL INPUT] but-
ton repeatedly to select COAX1,
COAX2, OPT1, OPT2, OPT3, or
(analog).
There are no assignments for
TUNER.
VIDEO 4 is used only for digital
input from the front panel terminals.
DIGITAL INPUT
Input selector buttons
DVD VIDEO 1 VIDEO 2
VCR 1 VCR 2
VIDEO 3 TAPE
CD
DIGITAL INPUT
DIGITAL INPUT
Examples:
If you connect your DVD player to the
OPTICAL IN 2 jack, set DVD to
OPT2.
If you want to listen to audio from the
component connected to the OPTICAL
IN 3 jack when the VIDEO 1 input
selector is selected, set VIDEO1 to
OPT3.
If you want to listen to audio from the
component connected to the COAX-
IAL IN 1 jack when the VIDEO 2 input
selector is selected, set VIDEO2 to
COAX1.
For input selectors that you dont want
to assign a digital input jack, set to
---- (analog).
44
First Time Setup
—Continued
Component Video Setup
If you connect to a COMPONENT VIDEO IN, you must
assign it to an input selector. For example, if you connect
your DVD player to COMPONENT IN 3, you should
assign it to the DVD input selector.
If you want to output composite and S-Video sources
from the COMPONENT VIDEO OUT, select VIDEO,
as explained below.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Minimum Speaker Impedance
(not North American models)
If the impedance of any of the connected speakers is 4
ohms or more, but less than 6 ohms, set the Minimum
Speaker Impedance to 4 ohms.
Note:
Before you change this setting, turn down the volume.
Input selector VIDEO IN jack
DVD IN 1
VIDEO 1 IN 2
VIDEO 2 IN 3
VIDEO 3 VIDEO
VIDEO 4 VIDEO
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 0. Initial
Setup, and then press [ENTER].
The Initial Setup menu appears.
3
Use the Up and Down [ ]/[ ]
buttons to select an input selec-
tor, and then use the Left and
Right [ ]/[ ] buttons to select:
IN1:
Use the video component
connected to COMPO-
NENT VIDEO IN 1.
IN2:
Use the video component
connected to COMPO-
NENT VIDEO IN 2.
IN3:
Use the video component
connected to COMPO-
NENT VIDEO IN 3.
RECEIVER
ENTER
ENTER
ENTER
VIDEO:
Output composite video
and S-Video sources from
the COMPONENT
VIDEO OUT.
4
Press the [SETUP] button.
The setup menu closes.
This setting is not set automatically by the Automatic
Speaker Setup function (see page 39).
2, 3
1, 4
2
1
45
First Time Setup
—Continued
TV Format Setup (not North American
models)
Here you can specify the TV format used in your area.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 0. Initial
Setup, and then press [ENTER].
The Initial Setup menu appears.
(Menus vary depending on country.)
3
Use the Up and Down [ ]/[ ]
buttons to select f. Sp Imped-
ance, and then use the Left and
Right [ ]/[ ] buttons to select:
4 ohms:
Select if the impedance of any
connected speaker is 4 ohms
or more, but less than 6 ohms.
6 ohms:
Select if the impedances of all
connected speakers are
between 6 and 16 ohms.
4
Press the [SETUP] button.
The setup menu closes.
RECEIVER
ENTER
ENTER
ENTER
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 0. Initial
Setup, and then press [ENTER].
The Initial Setup menu appears.
(Menus vary depending on country.)
3
Use the Up and Down [ ]/[ ]
buttons to select h. TV Format,
and then use the Left and Right
[ ]/[ ] buttons to select:
Auto:
Conforms with the video
input signal.
PAL:
Select if the TV system in
your area is PAL.
NTSC:
Select if the TV system in
your area is NTSC.
4
Press the [SETUP] button.
The setup menu closes.
RECEIVER
ENTER
ENTER
ENTER
46
First Time Setup
—Continued
AM Frequency Step Setup
(some models only)
Here you can specify the AM frequency step used in
your area. When this setting is changed, all radio presets
are deleted.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Some of the settings in this section are set automatically
by the Automatic Speaker Setup function (see page 39).
Here you can check the settings made by the Automatic
Speaker Setup function, or set them manually, which is
useful if you change one of the connected speakers after
using the Automatic Speaker Setup function.
Speaker Configuration
Here you can specify which speakers are connected and
their individual sizes.
For speakers with a cone diameter
over 6-1/2 inches (16 cm), specify
large,
and for those with a diameter
below this, specify
small.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 0. Initial
Setup, and then press [ENTER].
The Initial Setup menu appears.
3
Use the Up and Down [ ]/[ ]
buttons to select i. AM Freq
Step, and then use the Left and
Right [ ]/[ ] buttons to select:
10 kHz:
Select if 10 kHz steps are
used in your area.
9 kHz:
Select if 9 kHz steps are used
in your area.
4
Press the [SETUP] button.
The setup menu closes.
RECEIVER
ENTER
ENTER
ENTER
Speaker Setup
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
Cone diameter
1, 11
210
2
1
RECEIVER
47
First Time Setup
—Continued
2
Use the Up and Down [ ]/[ ]
buttons to select 1. Speaker
Cong, and then press [ENTER].
The Speaker Cong menu appears.
3
Use the Up and Down [ ]/[ ]
buttons to select a. Subwoofer,
and then use the Left and Right
[ ]/[ ] buttons to select:
Yes:
Select if a subwoofer is con-
nected.
No:
Select if no subwoofer is con-
nected.
4
Use the Up and Down [ ]/[ ]
buttons to select b. Front, and
then use the Left and Right [ ]/
[ ] buttons to select:
Small:
Select if the front speakers are
small.
Large:
Select if the front speakers are
large.
Note:
If the Subwoofer setting in step 3 is set
to No, this setting is xed at Large.
5
Use the Up and Down [ ]/[ ]
buttons to select c. Center, and
then use the Left and Right [ ]/
[ ] buttons to select:
Small:
Select if the center speaker is
small.
Large:
Select if the center speaker is
large.
None:
Select if no center speaker is
connected.
Note:
If the Front setting in step 4 is set to
Small, the Large option cannot be
selected.
ENTER
ENTER
ENTER
ENTER
ENTER
6
Use the Up and Down [ ]/[ ]
buttons to select d. Surround,
and then use the Left and Right
[ ]/[ ] buttons to select:
Small:
Select if the surround left and
right speakers are small.
Large:
Select if the surround left and
right speakers are large.
None:
Select if no surround left and
right speakers are connected.
Note:
If the Front setting in step 4 is set to
Small, the Large option cannot be
selected.
7
Use the Up and Down [ ]/[ ]
buttons to select e. SurrBack,
and then use the Left and Right
[ ]/[ ] buttons to select:
Small:
Select if the surround back
left and right speakers are
small.
Large:
Select if the surround back
speakers are large.
None:
Select if no surround back
speakers are connected.
Notes:
If the Surround setting in step 6 is set
to None, this setting cannot be
selected.
If the Surround setting in step 6 is set
to Small, this setting cannot be set to
Large.
8
Use the Up and Down [ ]/[ ]
buttons to select f. SurrBack
ch, and then use the Left and
Right [ ]/[ ] buttons to select:
1ch:
Select if one surround back
speaker is connected.
2ch:
Select if two (left and right)
surround back speakers are
connected.
Note:
If the Surround Back Setting in step 7 is
set to None, this setting cannot be
selected.
Continue with step 9 on page 48.
ENTER
ENTER
ENTER
48
First Time Setup
—Continued
Crossover
Note:
If the crossover frequency is set to a low value, and the
program material doesnt contain any sounds below that
frequency, the subwoofer will not output much sound.
Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left and right
channels to the subwoofer. This function can be set only
if the Subwoofer setting in step 3 is set to Yes, and the
Front setting in step 4 is set to Large.
In the speaker setup screen, you can choose how bass
information is distributed to your speakers only if you
have large front left and right speakers AND a sub-
woofer.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
9
Use the Up and Down [ ]/[ ]
buttons to select g. Crossover,
and then use the Left and Right
[ ]/[ ] buttons to select a
crossover frequency.
Choose a crossover frequency suitable
for your setup. If youre using a sub-
woofer, choose a crossover frequency
based on the diameter of your front
speakers. If youre not using a sub-
woofer, use the diameter of any speaker
that you specied as Small.
Continue with step 10 in the right col-
umn.
ENTER
Speaker cone
diameter
Crossover
frequency
Over 8 in.
(20 cm)
60 Hz
6-1/2 to 8 in.
(16–20 cm)
80 Hz
5-1/4 to 6-1/2 in.
(13–16 cm)
100 Hz
3-1/2 to 5-1/4 in.
(9–13 cm)
120 Hz
Under 3-1/2 in.
(9 cm)
150 Hz
10
Use the Up and Down [ ]/[ ]
buttons to select h. Double
Bass, and then use the Left and
Right [ ]/[ ] buttons to select:
On:
Double Bass function on
(default). Front left and right
bass also goes to the sub-
woofer simultaneously.
Off:
Double Bass function off.
11
Press the [SETUP] button.
The setup menu closes.
This setting is not set automatically by the Automatic
Speaker Setup function (see page 39).
ENTER
49
First Time Setup
—Continued
Speaker Distance
Here you can specify the distance from each speaker to
the listening position so that the sound from each
speaker arrives at the listeners ears as the sound
designer intended.
Notes:
The Center and Subwoofer distances can be set up to
5 ft. (1.5 m) more or less than the Front distance. For
example, if the Front distance is set to 20 ft. (6 m), the
Center and Subwoofer distances can be set between
15 and 25 ft. (4.5 and 7.5 m). The Surr Right, Surr
Left, and Surr Back distances can be set up to 5 ft.
(1.5 m) more or 15 ft. (4.5 m) less than the Front dis-
tance. For example, if the Front distance is set to 20 ft.
(6 m), the Surr Right, Surr Left, and Surr Back dis-
tances can be set between 5 and 25 ft. (1.5 and 7.5 m).
This procedure can also be performed on the AV
receiver by using its [SETUP] button, arrow buttons,
and [ENTER] button.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 2. Speaker Dis-
tance, and then press [ENTER].
The Speaker Distance menu appears.
Note:
Speakers that you set to No or None on
the Speaker Conguration page
(page 46) cannot be selected.
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
1, 6
25
2
1
RECEIVER
ENTER
ENTER
3
Use the Up and Down [ ]/[ ]
buttons to select a. Unit, and
then use the Left and Right [ ]/
[ ] buttons to select:
feet:
Select if you want to enter
distances in feet. Can be set
from 1 to 30 feet in 1-foot
steps.
meters:
Select if you want to enter
distances in meters. Can be
set from 0.3 to 9 meters in
0.3-meter steps.
4
Use the Up and Down [ ]/[ ]
buttons to select b. Front, and
then use the Left and Right [ ]/
[ ] buttons to specify the dis-
tance.
Specify the distance from the front left
speaker to your listening position.
5
Repeat step 4 for all speakers.
6
Press the [SETUP] button.
The setup menu closes.
ENTER
ENTER
50
First Time Setup
—Continued
Speaker Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
Note:
The speakers cannot be calibrated while the output of the
AV receiver is muted, while a pair of headphones is con-
nected, or when using the multichannel input.
Note:
This procedure can also be performed by using the
remote controller. First press the [TEST TONE] button
to output the test tone. Use the [LEVEL] and
[LEVEL+] buttons to set the volume, and use the [CH
SEL] button to select the speakers.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
1, 5
2, 3
2
1
RECEIVER
2
Use the Up and Down [ ]/[ ]
buttons to select 3. Level Cali-
bration, and then press
[ENTER].
The Level Calibration menu appears
and the pink noise test tone is output by
the front left speaker.
Note:
Speakers that you set to No or None on
the Speaker Conguration page
(page 46) cannot be selected.
3
Use the Up and Down [ ]/[ ]
buttons to select each speaker,
and use the Left and Right [ ]/
[ ] buttons to set the volume.
The volume can be adjusted from 12
to +12 dB in 1 dB steps (15 to +12 dB
for the subwoofer).
4
Repeat step 3 until the volume of
the test tone from each speaker
is the same.
5
Press the [SETUP] button.
The setup menu closes.
ENTER
ENTER
ENTER
51
First Time Setup
—Continued
Equalizer Setting
Here you can adjust the EQ of individual speakers. To set
the volume of individual speakers see page 50.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 5. Equalizer
Settings, and then press
[ENTER].
The Equalizer Settings menu appears.
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
1, 7
26
2
1
RECEIVER
ENTER
ENTER
3
Use the Left and Right [ ]/[ ]
buttons to select:
Off:
Tone off, response at.
Auto:
The tone for each speaker is
set automatically by the
Automatic Speaker Setup
function.
Manual:
You can adjust the EQ of each
speaker manually.
If you select Manual, continue with this
procedure. If you select Off or Auto, go
to step 7.
4
Use the Down [ ] button to
select Channel, and then use
the Left and Right [ ]/[ ] but-
tons to select a speaker.
5
Use the Up and Down [ ]/[ ]
buttons to select a frequency,
and then use the Left and Right
[ ]/[ ] buttons to adjust the
level at that frequency.
The volume at each frequency can be
adjusted from 6 to +6 dB in 1 dB
steps.
Tip:
Low frequencies (e.g., 80 Hz)
affect bass sounds; high frequencies
(e.g., 8 kHz) affect treble sounds.
6
Use the Up [ ] button to select
Channel, and then use the Left
and Right [ ]/[ ] buttons to
select another speaker.
Repeat steps 5 and 6 for each speaker.
7
Press the [SETUP] button.
The setup menu closes.
ENTER
ENTER
ENTER
ENTER
52
First Time Setup
—Continued
If you connect an -compatible Onkyo MiniDisc
recorder or CD recorder to the TAPE IN/OUT jacks, for
to work properly, you must change this setting.
This setting can only be changed on the AV receiver.
Changing the TAPE/MD/CDR Display
1
Press the [TAPE] input selector
button so that TAPE appears
on the display.
2
Press and hold down the [TAPE]
input selector button (about 3
seconds) to set the display.
Repeat this step to select TAPE, MD, or
CDR.
1, 2
TAPE
TAPE
53
Basic Operations
This section explains how to select the input source (i.e., the AV component that you want to listen to or watch).
Selecting the Input Source
1
3
3
1
1
1
Use the AV receivers input selector buttons to select the input
source.
To select the input source with the remote controller, press the
[RECEIVER] button, and then use the INPUT SELECTOR buttons.
On the remote controller, the [V1], [V2], [V3], and [V4] buttons select the
VIDEO 1, VIDEO 2, VIDEO 3, and VIDEO 4 input sources, respectively.
2
Start playback on the source component.
When you select DVD or another video component, on your TV, youll need
to select the video input thats connected to the AV receivers MONITOR
OUT.
On some DVD players, you may need to turn on the digital audio output.
3
To adjust the volume, use the MASTER VOLUME control, or the
remote controllers [VOL] button.
The volume can be set to MIN, 1 through 99, or MAX.
The AV receiver is designed for home theater enjoyment. It has a wide volume
range, allowing precise adjustment.
DVD VIDEO 1
VIDEO 2
VCR 1
VCR 2
VIDEO 3 VIDEO 4
TAPE
TUNER CD
MLUTI CH
RECEIVER
or
Remote
controller
AV receiver
VOL
MASTER VOLUME
or
Remote
controller
AV receiver
54
Basic Operations
—Continued
You can adjust the brightness of the display.
You can temporarily mute the output of the AV receiver.
With the sleep timer, you can set the AV receiver to turn
off automatically after a specied period.
If you need to cancel the sleep timer, press the [SLEEP]
button repeatedly until the SLEEP indicator disappears.
To check the time remaining until the AV receiver sleeps,
press the [SLEEP] button. Note that if you press the
[SLEEP] button while the sleep time is being displayed,
youll shorten the sleep time by 10 minutes.
You can connect a pair of stereo headphones (1/4-inch
phone plug) to the AV receivers PHONES jack for pri-
vate listening, as shown.
Notes:
Always turn down the volume before connecting your
headphones.
The speakers are turned off while the headphones plug
is inserted in the PHONES jack (Zone 2 speakers are
not turned off).
When you connect a pair of headphones, the listening
mode is set to Stereo, unless its already set to Stereo,
Mono, Direct, or Pure Audio (not North American
TX-SR603).
Only the Stereo, Direct, Pure Audio (not North Amer-
ican TX-SR603), and Mono listening modes can be
used with headphones (the listening modes available
also depends on the currently selected input source).
When the multichannel input is used, only the front
left and right audio can be heard in the headphones.
To adjust the headphone level, press the [CH SEL]
button on the remote controller, and then press the
[LEVEL +]/[LEVEL -] buttons. You can adjust the
level between 12 dB and +12 dB.
Setting the Display Brightness
Press the [RECEIVER] button,
and then press the [DIMMER]
button repeatedly to select:
Normal+VOLUME light on.
Normal+VOLUME light off.
Dim+VOLUME light off.
Dimmer+VOLUME light off.
Muting the AV Receiver
Press the [RECEIVER] button,
and then press the [MUTING] but-
ton.
The output is muted and the MUTING
indicator ashes on the display, as
shown.
To unmute the AV receiver, press the
[MUTING] button again, or adjust the
volume.
The Mute function is cancelled when
the AV receiver is set to Standby.
DIMMER
SLEEP
MUTING
Press
[RECEIVER]
rst
RECEIVER
DIMMER
RECEIVER
MUTING
Using the Sleep Timer
Press the [RECEIVER] button,
and then press the [SLEEP] but-
ton repeatedly to select the
required sleep time.
The sleep time can be set from 90 to 10
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been
set. The specied sleep time appears on
the display for about ve seconds, then
the previous display reappears.
Using Headphones
RECEIVER
SLEEP
PHONES
55
Basic Operations
—Continued
You can display various information about the current
input source as follows.
Note:
This procedure can also be performed on the AV receiver
by using its [DISPLAY] button.
The following information can typically be displayed for
input sources.
*If the input signal is analog, no format information is
displayed. If the input signal is PCM, the sampling fre-
quency is displayed. If the input signal is digital but not
PCM, the signal format is displayed. Information is
displayed for about three seconds, then the previously
displayed information reappears.
Interpreting Surround Channel Values
A: The number of front channels (3 means front left,
front right, and center).
B: The number of surround channels (2 means surround
left and surround right). If theres surround back
channel information, this will be 3.
C: LFE channel for subwoofer (1 means yes).
Displaying Source Information
Press the [RECEIVER] button,
and then press the [DISPLAY]
button repeatedly to cycle
through the available informa-
tion.
RECEIVER
DISPLAY
RECEIVER
DISPLAY
Input source &
volume
Signal format*
or sampling
frequency
Input source &
listening mode
ABC
56
Basic Operations
—Continued
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as presets
for quick selection.
Listening to the Radio
Tuning into Radio Stations
Auto Tuning Mode
When tuned into a station, the TUNED indicator
appears. When tuned into a stereo FM station, the FM
STEREO indicator appears on the display, as shown.
Manual Tuning Mode
The North American model changes FM frequency in
0.2 MHz steps, 10 kHz steps for AM. For other models
its 0.05 MHz steps for FM and 9 kHz steps for AM.
In Manual Tuning mode, FM stations will be in mono.
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Using the Tuner
1
Use the [TUNER] input selector
button to select either AM or FM.
In this example, FM has been selected.
Each time you press the [TUNER] but-
ton, the input source changes between
AM and FM.
(Actual display depends on country)
1
Press the [TUNING MODE] but-
ton so that the AUTO indicator
appears on the display.
2
Press the TUNING Up or Down
[ ]/[ ] button.
Searching stops when a station is
found.
TUNER
Band Frequency
21
TUNING MODE
TUNING
AUTOTUNED
FM STEREO
1
Press the [TUNING MODE] but-
ton so that the AUTO indicator
disappears from the display.
2
Press and hold the TUNING Up or
Down [ ]/[ ] button.
The frequency stops changing when
you release the button.
Press the buttons repeatedly to change
the frequency one step at a time.
TUNING MODE
TUNING
57
Basic Operations
—Continued
Presetting Radio Stations
You can store up to 40 of your favorite radio stations as
presets.
Selecting Preset Stations
Deleting Presets
Displaying Radio Information
1
Tune into the station that you
want to store as a preset.
2
Press the [MEMORY] button.
The MEMORY indicator appears and
the preset number ashes.
3
While the MEMORY indicator is
displayed (about 8 seconds), use
the PRESET [ ]/[ ] buttons to
select a preset from 1 through 40.
In this example, preset #3 is selected.
4
Press the [MEMORY] button
again to store the station.
The station is stored and the preset
number stops ashing.
Repeat this procedure for all your
favorite radio stations.
1
Use the [TUNER] input selector
button to select either AM or FM.
2
Use the PRESET [ ]/[ ] but-
tons, or the remote controllers
CH [+/] button to select a preset.
32, 4
MEMORY
PRESET
MEMORY
TUNER
PRESET
1
Select the preset that you want to
delete.
See the previous section.
2
While holding down the [MEM-
ORY] button, press the
[TUNING MODE] button.
The selected preset is deleted and its
number disappears from the display.
1
Press the [DISPLAY] button
repeatedly to cycle through the
available information.
2
MEMORY
TUNING MODE
CLEAR
1
DISPLAY
Band, frequency
& preset #
Listening mode
58
Basic Operations
—Continued
Using RDS (European models only)
RDS only works with European models and only in
areas where RDS broadcasts are available.
What is RDS?
RDS stands for
Radio Data System
and its a method of
transmitting data in FM radio signals. It was developed
by the European Broadcasting Union (EBU) and is avail-
able in most European countries. Many FM stations use
it these days. In addition to displaying text information,
RDS can also help you nd radio stations by type (e.g.,
news, sport, rock, etc.).
The AV receiver supports four types of RDS informa-
tion:
PS (Program Service)
When tuned to an RDS station thats broadcasting PS
information, the stations name appears. When you press
the [DISPLAY] button, the frequency is displayed for
three seconds.
RT (Radio Text)
When tuned to an RDS station thats broadcasting RT
text information, that information is shown on the dis-
play (see page 59).
PTY (Program Type)
You can also search for radio stations by type (see
page 59).
TP (Trafc Program)
You can also search for TP radio stations (see page 59).
Notes:
In some cases, the text characters displayed on the AV
receiver may not be identical to those broadcast by the
radio station. Also, unexpected characters may be dis-
played when unsupported characters are received.
This is not a malfunction.
If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
Program Types Used in Europe (PTY)
Type Display Description
None NONE No program type.
News
reports
NEWS Reports on current events and
happenings.
Current
affairs
AFFAIRS Topical reporting of current
affairs, often with a wider
range of topics than news
reports.
Information INFO General information such as
weather forecasts, consumer
affairs, medical help, etc.
Sport SPORT Live sports action, sports
news, and interviews.
Education EDUCATE Formal educational programs.
Drama DRAMA Radio plays and serials.
Culture CULTURE Cultural programs (including
religious affairs).
Science and
technology
SCIENCE Programs about the natural
sciences and technology.
Varied VARIED Speech-based programs not
covered by the above catego-
ries (e.g., quizzes, panel
games, and comedy).
Pop music POP M Popular commercial music,
usually from past or present
sales charts (e.g., Top 40).
Rock music ROCK M Popular music with an alterna-
tive appeal, often not appear-
ing on sales charts.
Middle of
the road
music
M.O.R.M Easy listening music (as
opposed to Pop, Rock, or
Classical).
Light
classics
LIGHT M Classical music for general
rather than specialist appreci-
ation.
Serious
classics
CLASSICS Performances of major
orchestral works, sympho-
nies, chamber music, etc.
(including Grand Opera).
Other music OTHER M Music styles not covered by
the above categories (e.g.,
Jazz, Rhythm & Blues, Folk,
Country, and Reggae).
Alarm ALARM When an RDS station is mak-
ing an emergency broadcast,
ALARM will flash on the dis-
play.
59
Basic Operations
—Continued
Displaying Radio Text (RT)
When tuned to an RDS station thats broadcasting RT
text information, that information can be displayed.
Notes:
The message Waiting may appear while the AV
receiver waits for RT information.
If the message No Text Data appears on the display,
no RT information is available.
Finding Stations by Type (PTY)
You can search for radio stations by type.
Listening to Traffic News (TP)
You can search for TP radio stations.
1
Press the [RT/PTY/TP] button
once.
The RT information scrolls across the
display.
1
Use the [TUNER] input selector
button to select FM.
2
Press the [RT/PTY/TP] button
twice.
The current program type appears on
the display.
3
Use the PRESET [ ]/[ ] but-
tons to select the type of pro-
gram you want.
See the table on page 58.
1
RT/PTY/TP
234, 51
TUNER
RT/PTY/TP
PRESET
4
To start the search, press
[ENTER].
The AV receiver searches until it nds a
station of the type you specied, at
which point it stops briey before con-
tinuing with the search.
5
When a station you want to listen
to is found, press [ENTER].
If no stations are found, the message
Not Found appears.
1
Use the [TUNER] input selector
button to select FM.
2
Press the [RT/PTY/TP] button
three times.
If the current radio station is broadcast-
ing TP (Trafc Program), [TP] will
appear on the display, and trafc news
will be heard as and when its broad-
cast. If TP without square brackets
appears, this means that the station is
not broadcasting TP.
3
To locate a station that is broad-
casting TP, press [ENTER].
The AV receiver searches until it nds a
station thats broadcasting TP.
If no stations are found, the message
Not Found appears.
ENTER
2 31
TUNER
RT/PTY/TP
ENTER
60
Basic Operations
—Continued
See About the Listening Modes on page 62 for
detailed information about the listening modes.
Selecting on the AV receiver
[PURE AUDIO] button (not North American
TX-SR603)
This button selects the Pure Audio listening mode.
While this mode is selected, the AV receiver outputs
no video signals and its display is turned off.
[STEREO] button
This button selects the Stereo listening mode.
LISTENING MODE [ ] [ ] buttons
These buttons select all the listening modes that can
be used with the current input source.
Modes can be selected in the following order,
depending on the input signal format:
Pure Audio
Direct
Stereo
Mono
Surround
(e.g., PLIIx, Neo:6, Dolby D EX, DTS/DTS 96/24,
DTS-ES, and so on)
Onkyo original DSP
Selecting with the Remote Controller
[SURR] button
This button selects the Dolby Digital, Pro Logic IIx,
Neo:6, DTS, and other listening modes.
[All ST] button
This button selects the All Ch Stereo listening mode.
[STEREO] button
This button selects the Stereo listening mode.
[PURE A] button (not North American
TX-SR603)
This button selects the Pure Audio listening mode.
While this mode is selected, the AV receiver outputs
no video signals and its display is turned off.
[DIRECT] button
This button selects the Direct listening mode.
[ DSP] & [DSP ] buttons
These buttons select the Onkyo original DSP modes
and Mono mode.
Selecting Listening Modes
The Dolby Digital and DTS listening modes
can only be selected if your DVD player is
connected to the AV receiver with a digital
audio connection (coaxial or optical).
Listening mode availability depends on the
format of the current input signal.
PURE AUDIO
STEREO
LISTENING MODE
PURE A
SURR
DIRECT
DSP
DSP
STEREO
ALL ST
(not
RC-590M)
61
Basic Operations
—Continued
The following table lists all the listening modes and shows which modes can be selected for each input signal format.
Input signal format
Analog,
PCM*1
1. In the Pure Audio and Direct listening modes, PCM signals at 32 kHz, 44.1 kHz, and 48 kHz are processed at 64 kHz, 88.2 kHz, and 96 kHz, respec-
tively. 96 kHz signals are processed at 48 kHz for all listening modes other than Pure Audio, Direct, and Stereo.
Dolby D
DTS/DTS 96/24*2
2. In the Pure Audio, Direct, Stereo, and DTS 96/24 listening modes, signals are processed as DTS 96/24. Everything else is processed as DTS.
Multich
3/2, 2/2 2/0 1/0,1+1 Other 3/2, 2/2 2/0
1/0,
1+1
Other
DTS-
ES
Source
CD, TV, LD,
VHS, MD,
turntable,
radio,
cassette,
DTV, etc.
DVD, DTV, etc. DVD, LD, CD, etc. DVD
Listening mode
Pure Audio
❍❍❍❍
❍❍❍
Direct
Stereo
❍❍
❍❍
❍❍❍
Mono
PLIIx Movie/Music/Game *3
3. If the SurrBack parameter is set to None, or the Zone 2 speakers are being used, PLII is used.
❍❍
Neo:6 Cinema
Neo:6 Music *4
4. Available only when Surround speakers are connected.
❍❍
Dolby D
Dolby D EX *5
5. Cannot be selected if the SurrBack parameter is set to None or the Zone 2 speakers are being used.
Dolby D+PLIIx Movie *6
6. Cannot select if the SurrBack ch setting is not set to 2ch, or the Zone 2 speakers are being used.
Dolby D+PLIIx Music *5
DTS, DTS 96/24
*7
7. If the SurrBack setting is set to None, or the Zone 2 speakers are being used, DTS is used.
DTS+Neo:6 *5
DTS+Dolby EX *5
DTS+PLIIx Movie *6/Music *5
DTS-ES Discrete *5
Discrete
DTS-ES Matrix *5
Matrix
Multich
Mono Movie
❍❍❍❍❍❍❍❍❍
Orchestra
Unplugged
Studio-Mix
TV Logic
All Ch Stereo
Full Mono
❍❍❍❍❍❍❍❍❍
62
Basic Operations
—Continued
About the Listening Modes
With its built-in surround sound decoders and DSP pro-
grams, the AV receiver can transform your home listen-
ing room into a movie theater or concert hall.
If you connect two surround back speakers (i.e., left and
right), both will be used for 6.1-channel surround play-
back.
Direct
The selected input source is output directly with minimal
processing for a pure sound.
Pure Audio
As an extension of Direct mode, this mode turns off the
display, turns off the power to the video circuitry, and
minimizes any other possible noise sources, providing a
high delity sound thats true to the original (since the
power to the video circuitry is turned off, no video sig-
nals are output while this mode is selected).
Stereo
The selected input source is processed as a stereo signal
and output by the front left and right speakers and the
subwoofer.
Mono
Use this mode when watching an old movie with a mono
soundtrack, or to select multilingual soundtracks
recorded in the left and right channels of some movies.
It can also be used when playing a DVD or other source
with multiplexed audio, such as a karaoke DVD.
Dolby Pro Logic II Movie
Use this mode with DVDs and vid-
eos that bear the Dolby Surround
logo or TV programs that feature Dolby Surround. You
can also use this mode with stereo movies or TV pro-
grams and the AV receiver will create a 5.1 surround mix
from the 2-channel stereo.
Dolby Pro Logic II Music
Use this mode to add 5.1 surround to stereo sources such
as music CDs and DVDs.
Dolby Pro Logic IIx
If youve connected surround back speakers to the AV
receiver, Dolby Pro Logic IIx allows you to enjoy 7.1-
channel playback from 2-channel or 5.1-channel music
or movies. Dolby Pro Logic IIx provides a well dened,
natural multichannel surround sound experience, putting
the listener in a seamless envelope of sound. The added
drama and natural sound enhance the listening experi-
ence with CDs, movies, and games.
Dolby Pro Logic IIx has three modes of operation:
Movie mode for movies, Music mode for listening to
music, and Game mode for use with game consoles with
2-channel stereo outputs.
Dolby Digital
With this format you can experience the
same superb sound that you get at a movie
theater or concert hall. Use this mode with DVDs that
bear the Dolby Digital logo.
Dolby Digital EX
With an added surround-back channel,
this 6.1-channel format offers a height-
ened sense of space, for added realism with moving
sounds, such as those that rotate 360 degrees or pass
overhead. Dolby Digital EX material can also be played
on conventional 5.1-channel systems, in which case the
surround-back channel audio is split between the sur-
round left and right channels. Use this mode with DVDs
that have a 5.1-channel soundtrack and bear the Dolby
Digital logo.
DTS
This digital surround format offers a sur-
round sound experience with exceptional
delity. It uses compressed digital audio
data, with six discrete channels (5.1), and the
ability to handle large amounts of audio data while
remaining faithful to the original. DTS provides very
high-quality sound. Youll need a DTS compatible DVD
player in order to enjoy DTS material. Use this mode
with DVDs, LDs, or CDs that bear the DTS logo.
DTS 96/24
This mode provides higher audio quality.
Use it with CDs, DVDs, and LDs that bear
the DTS 96/24 logo.
DTS-ES Discrete
This is DTS with an added surround back
channel for 6.1 surround sound. Use it with
program material recorded in DTS 6.1 format. With the
additional surround back channel, this format offers 6.1
fully independent digital channels, providing a realistic
sense of movement and space. Use it with program mate-
rial recorded in DTS 6.1, such as CDs, DVDs, or LDs
that bear the DTS-ES logo.
The AV receiver’s surround indicators show which
speakers are active in each listening mode.
Front left Center Front right
Subwoofer
Surround
right
Surround
back left/
right
Surround
left
63
Basic Operations
—Continued
DTS-ES Matrix
This is DTS with an added surround back
channel for 6.1 surround sound. Use it to
provide 6.1-channel surround playback
with program material recorded in DTS 5.1
format. Since DTS 5.1 program material
contains surround back channel informa-
tion, all channels can be reconstructed for 6.1-channel
playback. Use this mode with CDs, DVDs, or LDs that
bear the DTS-ES or DTS logo.
Neo:6
This mode provides 6.1-channel playback from 2-chan-
nel sources. It offers six full-bandwidth channels with
excellent separation. There are two modes of operation:
Cinema mode for movies, and Music mode for listening
to music.
Cinema mode simulates the realistic sense of movement
that you get with 6.1-channel surround sound sources.
Use this mode with videos, DVDs, and TV programs that
feature stereo sound.
Music mode uses the surround channels to simulate a
natural sound eld that cannot be produced with conven-
tional stereo. Use this mode with stereo material such as
music CDs.
Onkyo Original DSP Modes
Orchestra
Suitable for classical or operatic music. The surround
channels are emphasized in order to widen the stereo
image. In addition, it simulates the natural reverberation
of a large hall.
Unplugged
Suitable for acoustic instrument sounds, vocals, and jazz
music. By emphasizing the front stereo image, it simu-
lates the stage-front experience.
Studio-Mix
Suitable for rock and pop music. Listening to music in
this mode creates a lively sound eld with a powerful
acoustic image, like being at a club or rock concert.
TV Logic
Adds realistic acoustics to TV programs produced in a
TV studio. In addition, it adds surround effects to the
entire sound and adds clarity to voices.
Mono Movie
This mode is suitable for use with old movies and other
mono sound sources. The center speaker outputs the
sound as it is, while reverb is applied to the sound output
by the other speakers, giving presence to even mono
material.
All Ch Stereo
Ideal for background music. The front, surround, and
surround back channels create a stereo image that lls
the entire listening area.
Full Mono
In this mode, all speakers output mono audio, so the
music sounds the same regardless of where you are.
64
Advanced Operations
With the Late Night function, you can reduce the
dynamic range of Dolby Digital material so that you can
still hear quiet parts even when listening at low volume
levelsideal for watching movies late at night when you
dont want to disturb anyone.
Notes:
The effect of the Late Night function depends on the
Dolby Digital material that you are playing, and with
some material there will be little or no effect.
The Late Night function is set to Off when the AV
receiver is set to Standby.
With the CinemaFILTER, you can soften overly bright
movie soundtracks, which are typically mixed for repro-
duction in a movie theater.
CinemaFILTER can be used with the following listening
modes: Dolby Digital, Dolby Digital EX, Dolby Pro
Logic IIx Movie, Dolby Pro Logic II Movie, DTS, DTS-
ES, DTS Neo:6 Cinema, DTS 96/24, DTS+Neo:6, and
DTS+Dolby EX.
Using the Late Night Function
(Dolby Digital only)
1
Press the [RECEIVER] button,
and then press the [L NIGHT]
button repeatedly to select:
Off:
Late Night function off.
Low:
Small reduction in dynamic
range.
High:
Big reduction in dynamic
range.
RECEIVER
L NIGHT
CINE FLTR
RECEIVER
L NIGHT
Using the CinemaFILTER
1
Press the [RECEIVER] button,
and then press the [CINE FLTR]
button repeatedly to select:
On:
CinemaFILTER on.
Off:
CinemaFILTER off.
RECEIVER
CINE FLTR
65
Advanced Operations
—Continued
You can adjust the level of individual speakers during
playback. These adjustments are temporary and will be
cancelled when the AV receiver is set to Standby.
Notes:
You cannot use this function while the AV receiver is
muted.
Speakers that are set to No or None in the Speaker
Conguration cannot be adjusted.
The DVD analog multichannel input is for connecting
components with a 5.1-channel analog audio output,
such as a DVD player or MPEG decoder.
See Using a Multichannel Connection on page 29 for
connection information.
Note:
To use the bass and treble functions with the DVD ana-
log multichannel input, select the Multich listening
mode rst.
Adjusting Individual Speaker Levels
1
Press the [RECEIVER] button,
use the [CH SEL] button to select
each speaker, and use the
[LEVEL] and [LEVEL+] buttons
to adjust the volume.
Speakers are selected in the following
order: Front Left
Center
Front
Right
Surr Right
Surr Back
Right
Surr Back Left
Surr Left
Subwoofer.
You can adjust the volume of each
speaker from 12 dB to +12 dB
(15 dB to +12 dB for the subwoofer).
The name of the currently selected
speaker and its volume appear on the
display, as shown.
RECEIVER
CH SEL
LEVEL +
MULTI CH
RECEIVER
CH SEL
LEVEL
+
LEVEL
-
Using the DVD Analog Multichannel
Input
1
Press the [RECEIVER] button fol-
lowed by the [MULTI CH] button
so that the MULTI CH indicator
appears on the display.
RECEIVER
66
Advanced Operations
—Continued
Adjusting Individual Speaker Levels
You can adjust the level of individual speakers while
using the DVD analog multichannel input.
Adjusting with onscreen setup menus:
Adjusting with the remote controller:
Notes:
These speaker level settings are completely indepen-
dent of those explained on pages 50, 65.
While the DVD analog multichannel input is selected,
you can only select the Direct, Pure Audio (not North
American TX-SR603), or Multich listening mode. If
you select the DVD analog multichannel input while
using another listening mode, that listening mode will
be cancelled.
While the DVD analog multichannel input is selected,
the Automatic Speaker Setup on page 39 and Speaker
Conguration settings on page 46 are ignored, and sig-
nals from the multichannel input are fed to the front left,
front right, center, surround left, and surround right
speakers, and subwoofer regardless of those settings.
This section explains how to record the current input
source, how to record one input source while enjoying
another, and how to dub audio onto your video record-
ings.
Unless you have the full consent of the copyright
holder, copyright laws prohibit using your recordings
for anything other than personal enjoyment!
Notes:
The surround sound and DSP listening modes cannot
be recorded.
Copy-protected DVDs cannot be recorded.
You cannot record from the DVD analog multichannel
input.
Various restrictions apply to digital recording. Refer
to the manuals supplied with your digital recording
equipment for more details.
Digital input signals are output by only the digital out-
puts, and analog input signals are output by only the
analog outputs. There is no internal conversion from
digital to analog or vice versa.
DTS signals will be recorded as noise, so dont
attempt analog recording of DTS CDs or LDs.
While the listening mode is set to Pure Audio, no
image is provided because the power is turned off for
the video circuit. If you want to make recordings,
select other listening mode.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 3. Multich
Level Adjust, and then press
[ENTER].
The Multich Level Adjust menu
appears.
3
Use the Up and Down [ ]/[ ]
buttons to select each speaker,
and use the Left and Right [ ]/
[ ] buttons to set the volume.
The volume can be adjusted from 12
to +12 dB in 1 dB steps (30 to +12 dB
for the subwoofer).
1
Use the remote controllers [CH
SEL] button to select each
speaker, and then use the
[LEVEL] and [LEVEL+] buttons
to adjust the volume.
The level can be adjusted from 12 to
+12 dB (30 to +12 dB for the sub-
woofer).
RECEIVER
ENTER
ENTER
ENTER
CH SEL
LEVEL
+
LEVEL
-
Recording
67
Advanced Operations
—Continued
AV Recording
You can record AV input sources to an AV recording
component (VCR, etc.) connected to the VIDEO 1 OUT,
VIDEO 2 OUT, or TAPE OUT. See pages 2737 for
information on connecting components.
Recording Separate AV Sources
Here you can record audio and video from completely
separate sources, allowing you to overdub audio onto
your video recordings. This function takes advantage of
the fact that when an audio-only input source (i.e.,
TAPE, TUNER, or CD) is selected, the video input
source remains unchanged.
In the following example, audio from the CD player con-
nected to the CD IN, and video from the camcorder con-
nected to the VIDEO 4 INPUT VIDEO jack are recorded
by the VCR connected to the VIDEO 1 OUT jacks.
1
Use the input selector buttons to
select the AV component that
you want to record.
Audio signals from the selected input
source are output by the VIDEO 1
OUT, VIDEO 2 OUT, and TAPE OUT
only.
You can watch the source while record-
ing, and the AV receivers VOLUME
control has no effect on recording.
2
Start recording on the AV compo-
nent connected to the VIDEO 1
OUT, VIDEO 2 OUT, or TAPE OUT.
3
Start playback on the source AV
component.
If you select another input source dur-
ing recording, that input source will be
recorded.
1
DVD VIDEO 1 VIDEO 2
VCR 1 VCR 2
VIDEO 3 VIDEO 4 TAPE
TUNER CD
1
Prepare the camcorder and CD player for
playback.
2
Prepare the VCR for recording.
3
Press the [VIDEO 4] input selector button.
4
Press the [CD] input selector button.
This selects the CD player as the audio source, but
leaves the camcorder as the video source.
5
Start recording on the VCR and start play-
back on the camcorder and CD player.
The video from the camcorder and the audio from
the CD player are recorded by the VCR.
S VIDEO VIDEO
VIDEO 4 INPUT
LR
AUDIO
DIGITAL
Camcorder
VCRCD player
video signal
audio signal
68
Advanced Setup
You can adjust the bass and treble for the front speakers,
except when the Direct or Pure Audio (not North Amer-
ican TX-SR603) listening mode is selected.
Bass
You can boost or cut low-frequency sounds output by the
front speakers from 10 dB to +10 dB in 2 dB steps.
Treble
You can boost or cut high-frequency sounds output by
the front speakers from 10 dB to +10 dB in 2 dB steps.
Here you can set listening mode-related settings and
functions.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Adjusting the Bass & Treble
1
Press the [TONE] button repeat-
edly to select either Bass or
Treble.
2
Use the TONE []/[+] buttons to
adjust.
1 2
TONE
+
Audio Adjust Functions
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 4. Audio
Adjust, and then press [ENTER].
The Audio Adjust menu appears.
3
Use the Up and Down [ ]/[ ]
buttons to select the settings,
and use the Left and Right [ ]/
[ ] buttons to set them.
The settings are explained on page 69.
4
When youve nished, press the
[SETUP] button.
The setup menu closes.
RECEIVER
ENTER
ENTER
ENTER
69
Advanced Setup
—Continued
The Audio Adjust functions are explained below.
Input Channel Settings
Multiplex
This setting determines which channel is output from a
stereo multiplex source. Use it to select audio channels
or languages with multiplex sources, multilingual TV
broadcasts, and so on.
Main:
The main channel is output (default).
Sub:
The sub channel is output.
Main/Sub:
Both the main and sub channels are output.
Mono (2chSource)
This setting species the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or 2-
channel analog/PCM source in the Mono listening
mode.
L+R:
Both the left and right channels are output
(default).
L:
Only the left channel is output.
R:
Only the right channel is output.
PL IIx Music Mode Settings
These settings provide for playing any 2-channel digital
source such as Dolby Digital, or 2-channel analog/PCM
source in the PLIIx Music listening mode.
Panorama
With this function, you can broaden the width of the
front stereo image when using the Pro Logic II Music or
Pro Logic IIx Music listening mode.
On:
Panorama function on.
Off:
Panorama function off (default).
Dimension
With this setting, you can move the sound eld forward
or backward when using the Pro Logic II Music or Pro
Logic IIx Music listening mode. The default setting is 3.
Higher settings move the sound eld forward. Lower set-
tings move it backward.
If the stereo image feels too wide, or there is too much
surround sound, move the sound eld forward to
improve the balance. Conversely, if the stereo image
feels like it is in mono, or there is not enough surround
sound, move it backward.
Center Width
With this function, you can adjust the width of the sound
from the center speaker when using the Pro Logic II
Music or Pro Logic IIx Music listening mode. Normally
if you are using a center speaker, the center channel
sound is output by only the center speaker. (If you are not
using a center speaker, the center channel sound will be
distributed to the front left and right speakers to create a
phantom center). This setting controls the front left,
right, and center mix, allowing you to adjust the weight
of the center channel sound. It can be adjusted from 0 to
7 (default is 3).
Neo:6 Music Mode Setting
Center Image
The DTS Neo:6 Music listening mode creates 6-channel
surround sound from 2-channel (stereo) sources. With
this setting, you can specify by how much the front left
and right channel output is attenuated in order to create
the center channel. It can be adjusted from 0 to 5 (default
is 3). This setting is unavailable if no surround speakers
are connected.
When set to 0, the front left and right channel output is
attenuated by half (6 dB), giving the impression that the
sound is located centrally. This setting works well when
the listening position is considerably off center. When
set to 5, the front left and right channels are not attenu-
ated, maintaining the original stereo balance.
Dolby Digital EX Input Signal Setting
Dolby D EX
This setting determines how Dolby Digital EX signals
are handled. This setting is unavailable if no surround
back speakers are connected.
Auto:
If the source signal contains a Dolby Digital
EX ag, the Dolby Digital EX listening mode
is used (default).
Manual:
You can select Pro Logic IIx Movie, Pro
Logic IIx Music, Dolby Digital, or Dolby
Digital EX.
70
Advanced Setup
—Continued
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set the
default listening mode to be used with Dolby Digital
input signals. You can select other listening modes dur-
ing playback, but the mode specied here will be
resumed once the AV receiver has been set to Standby.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Assigning Listening Modes to Input
Sources
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 6. Input
Setup, and then press [ENTER].
The Input Setup menu appears.
3
Use the INPUT SELECTOR but-
tons on the remote controller to
select the input source that you
want to set.
For input selectors that have no digital
input jacks, only b. Analog will be
available.
RECEIVER
ENTER
ENTER
4
Use the Up and Down [ ]/[ ]
buttons to select the signal for-
mat that you want to set, and
then use the Left and Right [ ]/
[ ] buttons to select a listening
mode.
Only listening modes that can be used
with each input signal format can be
selected.
For Surround, the listening mode
specied on page 69 will be used.
The Last Valid option means that the
listening mode selected last will be
used.
b. Ana/PCM:
With this setting, you
can specify the listening mode to be
used when an analog (CD, TV, LD,
VHS, MD, turntable, radio, cassette,
cable, satellite, etc.) or PCM digital
(CD, DVD, etc.) audio signal is played.
c. Dolby D:
With this setting, you can
specify the listening mode to be used
when a Dolby Digital format digital
audio signal is played (DVD, etc.).
d. DTS:
With this setting, you can
specify the listening mode to be used
when a DTS format digital audio signal
is played (DVD, LD, CD, etc.).
e. D.F. 2ch:
With this setting, you can
specify the listening mode to be used
when a 2-channel (2/0) digital audio
signal (Dolby Digital, DTS) is played
(DVD, etc.).
f. Mono:
With this setting, you can
specify the listening mode to be used
when a mono digital audio signal is
played (DVD, etc.).
g. Multich:
This setting is available
only when DVD or MULTI CH is
selected with INPUT SELECTOR.
With this setting, you can specify the
listening mode to be used when the
DVD analog multichannel input is
used.
5
When youve nished, press the
[SETUP] button.
The setup menu closes.
ENTER
71
Advanced Setup
—Continued
You can set the input level for each input source. This is
useful if some of your AV components are louder or qui-
eter than others.
While this menu is shown onscreen, you can select each
input source and set the levels while listening to and
comparing them.
This section explains the items on the Preference menu.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
IntelliVolume
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 6. Input
Setup, and then press [ENTER].
The Input Setup menu appears.
3
Use the INPUT SELECTOR but-
tons on the remote controller to
select the input source that you
want to set.
4
Use the Up and Down [ ]/[ ]
buttons to select
a. IntelliVolume.
If a component is too loud compared to
your other components, use the Left
[ ] button to adjust the level. If its too
quiet, use the Right [ ] button.
The level can be set from 6 dB to
+6 dB.
RECEIVER
ENTER
ENTER
ENTER
Setting Preferences
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 7. Preference,
and then press [ENTER].
The Preference menu appears.
3
Use the Up and Down [ ]/[ ]
buttons to select the settings,
and use the Left and Right [ ]/
[ ] buttons to set them.
The settings are explained on page 72.
4
When youve nished, press the
[SETUP] button.
The setup menu closes.
RECEIVER
ENTER
ENTER
ENTER
72
Advanced Setup
—Continued
a. Maximum Volume
With this preference, you can prevent the volume being
set too high by specifying a maximum volume level.
The range is from 50 to 99. To specify no maximum vol-
ume, select Off.
b. Power On Volume
With this preference, you can specify the volume setting
to be used each time the AV receiver is turned on.
The range is MIN, 1 through 50. To use the same volume
level that was used when the AV receiver was turned off,
select Last.
c. Immediate Display
This preference determines whether or not actions, such
as selecting an input source, are displayed onscreen.
Normal:
Select if your TV is 4:3.
Wide:
Select if your TV is 16:9.
Off:
Actions not displayed.
Even if this preference is set to Normal or Wide, actions
are not displayed on the TV or projector thats connected
to the COMPONENT VIDEO OUT.
d. Scan Mode
If the text in onscreen setup menus ickers due to com-
patibility with the connected display device (TV, projec-
tor, etc.), set the Scan Mode to Non-Interlaced.
Interlaced:
Default.
Non-Interlaced:
Select if the text ickers.
Depending on the display device, when Non-Inter-
laced is selected, the onscreen setup menus may not
appear. If this happens, use the AV receivers display
and repeat the procedure to revert to Interlaced.
e. Remote ID
With this setting, you can change the AV Receivers
remote control ID. You may need to change this if the
remote controllers control codes overlap with those of
another Onkyo component located in the same room.
If you change the AV receivers remote control ID, be
sure to set the same ID on both the AV receiver and
remote controller (see page 73). The default ID for
both is 1.
f. IR IN Position
When using a commercially available IR receiver, use
this setting to specify its location.
Main:
Select if the IR receiver is located in the main
room.
Zone 2:
Select if the IR receiver is located in, and will
be used to control Zone 2.
The digital input signal formats are available only for the
input sources that you have assigned a digital input jack;
otherwise you will see Analog indicated on the screen
(see page 43).
Normally, the AV receiver detects the signal format auto-
matically. However, if you experience either of the fol-
lowing issues when playing PCM or DTS material, you
can manually set the signal format to PCM or DTS:
If the beginnings of tracks from a PCM source are cut
off, try setting the format to PCM.
If noise is produced when fast forwarding or reversing
a DTS CD, try setting the format to DTS.
Digital Input Signal Formats
1
Press and hold the AV receivers [DIGI-
TAL INPUT] button for about 3 seconds.
2
While Auto is displayed (about 3 sec-
onds), press the [DIGITAL INPUT] button
again to select: PCM, DTS, or Auto.
DTS or PCM:
The DTS or PCM indicator,
depending on which format you have set, ashes,
and only signals in that format are output. Digital
signals in other formats are ignored.
Auto (default):
The format is detected automat-
ically. If no digital input signal is present, the cor-
responding analog input is used instead.
DIGITAL INPUT
73
Advanced Setup
—Continued
If several Onkyo components are used in the same room,
the remote controllers control codes may overlap with
those of another component. To differentiate the remote
controllers control codes, you can change its ID to
another number.
Notes:
If you change the remote controllers ID, be sure to set
the same ID on both the remote controller and AV
receiver (see e. Remote ID on page 72). The default ID
for both is 1.
Changing the Remote Controllers ID
1
Press and hold down the [RECEIVER]
button, and then press the TV [INPUT]
button.
2
Use the number buttons to enter a remote
control ID.
You can enter 1, 2, or 3.
1
1
Number
buttons
74
Zone 2
With the Zone 2 function, you can enjoy one input
source in the main room and a different source in another
room.
There are two connection methods: using a receiver/inte-
grated amp in Zone 2 or using only a pair of speakers in
Zone 2.
Using a Receiver/Integrated Amp in Zone 2
With this connection method, you can use 7.1 surround
sound in the main room and play a different AV source
in Zone 2. The volume for Zone 2 is set on the receiver/
integrated amp.
Use an RCA audio cable to connect the AV receivers
ZONE 2 LINE OUT L/R jacks to an analog audio
input on your receiver/integrated amp.
Connect the Zone 2 speakers to the speaker terminals
on the receiver/integrated amp.
Using Only Speakers in Zone 2
With this connection method, you can use 5.1 surround
sound in the main room and play a different AV source
in Zone 2. The volume for Zone 2 is set on the AV
receiver.
Set the Powered Zone 2 setting to Activated (see
page 75).
Connect your Zone 2 speakers to the AV receivers
ZONE 2 SPEAKERS terminals.
Connecting Zone 2
R
L
IN
ZONE 2
LINEOUT
R
L
Main room
Zone 2
TV
TV
Receiver/
integrated amp
AV receiver
ZONE 2
SPEAKERS
L
R
RL
Main room
TV
Zone 2
AV receiver
75
Zone 2
—Continued
To use Zone 2, you must make this setting. It enables the
speakers connected to the ZONE 2 SPEAKERS termi-
nals so that they produce sound when Zone 2 is used.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Setting the Powered Zone 2
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [ ]/[ ]
buttons to select 0. Initial
Setup, and then press [ENTER].
The Initial Setup menu appears.
2, 3
2
1, 4
1
RECEIVER
ENTER
ENTER
3
Use the Up and Down [ ]/[ ]
buttons to select g. Powered
Zone 2, and use the Left and
Right [ ]/[ ] buttons to select:
Not Activated:
Zone 2 SPEAKERS
terminals deactivated.
Activated:
Zone 2 SPEAKERS termi-
nals activated.
When Zone 2 is activated and turned on
(see page 76), the speakers connected
to the ZONE 2 SPEAKERS terminals
output sound, but the speakers con-
nected to the SURROUND BACK
SPEAKERS terminals do not (when
Zone 2 is activated but not used, the
surround back speakers work as nor-
mal).
4
Press the [SETUP] button.
The setup menu closes.
ENTER
76
Zone 2
—Continued
Here you can turn on Zone 2, select an input source, and
adjust the volume.
Note:
To control Zone 2 with the remote controller, you must
press the [ZONE 2] button rst.
Notes:
If the Sleep function has been set, the Zone 2 compo-
nent will turn off along with the AV receiver when the
specied sleep time expires. To use the Sleep function
with Zone 2 only, set the Sleep function and then set
the AV receiver to Standby.
Only analog input sources are output by the ZONE 2
LINE OUT and ZONE 2 SPEAKERS terminals. Dig-
ital input sources are not output. If no sound is heard
when an input source is selected, check if its con-
nected to an analog input.
While Zone 2 is being used, listening modes that need
surround back speakers (i.e., Dolby Digital EX and
DTS-ES) are unavailable.
While Zone 2 is on, functions will not work.
You cant select different radio stations for Zone 2 and
the main room. For example, if you have an FM sta-
tion for the main room, that station will also be used
in Zone 2.
Using Zone 2
1
Point the remote controller at the
AV receiver and press the
[ZONE 2] button followed by the
[ON] button.
This turns on Zone 2 and the AV
receivers 12V TRIGGER OUT.
2
To select the Zone 2 input source
with the remote controller, press
the [ZONE 2] button followed by
an input selector button.
If you select AM or FM, you can use
the remote controllers [TUNER] but-
ton to select the band.
To perform steps 1 and 2 on the
AV receiver, press the [ZONE 2]
button followed by an input
selector button within eight sec-
onds.
The name of the selected Zone 2 source
appears on the display.
3
14
4
2
1
ZONE
2
ON
ZONE
2
To set Zone 2 to the same source as the
main room, press the [ZONE 2] button
repeatedly to display
Zone 2 Sel: Source.
3
To adjust the Zone 2 volume with
the remote controller, press the
[ZONE 2] button, and then use
the [LEVEL] and [LEVEL+] but-
tons.
To do this on the AV receiver,
press the ZONE 2 LEVEL [ ]/[ ]
buttons.
If the Zone 2 receiver/integrated amp is
connected to the AV receivers ZONE 2
LINE OUT L/R jacks, use the volume
control on the receiver/integrated amp.
4
To turn off Zone 2 with the
remote controller, press the
[ZONE 2] button followed by the
[STANDBY] button.
To do this from the AV receiver,
press the [OFF] button.
ZONE
2
LEVEL
+
LEVEL
-
ZONE
2
STANDBY
77
Zone 2
—Continued
Using the 12V Trigger
When Zone 2 is turned on, the ZONE 2 12V TRIGGER
OUT outputs 12 volts (100 milliamperes max). By con-
necting this jack to the 12-volt trigger input on, say, a
power amp in Zone 2, that power amp will turn on and
off automatically as and when Zone 2 is turned on and
off on the AV receiver.
To use the remote controller to control the AV receiver
from Zone 2, youll need one of the following commer-
cially available multiroom remote control kits:
Multiroom Kits such as those made by Niles and Xan-
tech.
These kits can also be used when the AV receiver is not
in line of sight of the remote controller, for example,
when its installed inside a cabinet.
Using a Multiroom Kit with Zone 2
In the following diagram, an IR receiver picks up the
infrared signals from the remote controller in Zone 2 and
feeds them to the AV receiver in the main room via the
connecting block.
On the Remote Setup menu, set the IR IN Position set-
ting to Zone 2 (see page 72).
Connect the miniplug cable from the connecting block to
the AV receivers IR IN jack as shown below.
Using a Multiroom Kit with a Cabinet
In the following diagram, an IR receiver picks up the
infrared signals from the remote controller and feeds
them to the AV receiver in the cabinet via the connecting
block.
On the Remote Setup menu, set the IR IN Position set-
ting to Main (see page 72).
Using the Remote Control in Zone 2
Connecting
block
Remote controller
IR receiver
Main room Zone 2
Signal flow
IR IN
from the connecting block
Miniplug cable
IR IN
Connecting
block
Remote controller
IR receiver
Inside
cabinet
Signal flow
78
Controlling Other Components
You can use the AV Receiver’s remote controller
(RC-590M/RC-591M) to control your other compo-
nents, including those made by other manufacturers.
This chapter explains how to:
Enter the remote control code for a component that
you want to control (e.g., DVD, TV, VCR).
Learn commands directly from another component’s
remote controller (see page 86).
Program the Macro function to perform a sequence of
actions with a single press of a button (see page 87).
Entering the appropriate remote control code for each
REMOTE MODE button will allow you to control your
other components with the remote controller. You’ll need
to perform this procedure for each component that you
want to control.
For the [DVD], [TV], [VCR], [CABLE], and [SAT] but-
tons, choose a code from the respective category. For the
[CD] and [MD/CDR] buttons, you can choose a code
from any category. Remote control codes cannot be
entered for the [RECEIVER] and [ZONE 2] buttons.
If the remote controller works OK, the code has been
entered correctly. If not, try again or try another code.
Codes for Onkyo DVD Players
The remote control code for an Onkyo DVD player
depends on whether it’s connected via , as follows:
5001:
Use this code if you’ve connected an cable
and an analog audio cable to your DVD player.
This is the default setting, so if you’re using
, you don’t need to change anything. Point
the remote controller at the AV receiver to
operate the DVD player.
5002:
Use this code if your DVD player doesn’t have
an jack, or you’re not using . Point the
remote controller at the DVD player to operate
it.
Setting the [MD/CDR] Button to CDR
By default, the [MD/CDR] button is set to control a
MiniDisc recorder. To control a CD recorder, it must be
set to CDR. The codes are as follows:
6002:
Code for controlling an CD recorder.
6003:
Code for controlling an MD recorder (default).
Entering Remote Control Codes
1
Look up the remote control code
for your component.
See “Remote Control Codes” on
page 80.
2
2
3
2
While holding down the REMOTE
MODE button that you want to
enter the code for, press the
[STANDBY] button.
3
Within 30 seconds, use the num-
ber buttons to enter the 4-digit
remote control code.
4
Select the remote controller
mode, point the remote control-
ler at the component, and check
its operation.
Remote controller buttons that can be
used in DVD mode are shown on
page 16. Those that can be used with
the TV, VCR, CABLE, and SAT modes
are shown on pages 84, 85.
STANDBY
79
Controlling Other Components
—Continued
Resetting REMOTE MODE Buttons
If youve entered another code for one of these button
and now want to return to the default, perform the fol-
lowing procedure.
By default, some REMOTE MODE buttons are prepro-
grammed with remote control codes for controlling
Onkyo components connected via .
Resetting the Remote Controller
Here you can reset the remote controller to its default
settings.
1
While holding down the REMOTE
MODE button that you want to
reset, press the TV [ ] button.
Release both buttons and wait two sec-
onds.
2
Press the REMOTE MODE button
again.
The REMOTE MODE button is reset.
STANDBY
REMOTE
MODE
TV
RECEIVER
1
While holding down the
[RECEIVER] button, press the
[STANDBY] button.
Release both buttons and wait ve sec-
onds.
2
Press the [RECEIVER] button
again.
The remote controller is reset.
RECEIVER
STANDBY
RECEIVER
80
Controlling Other Components
—Continued
Remote Control Codes
When two or more codes are given,
try each one in turn, and choose the
one that works best.
Depending on the manufacturer and
component, the remote controller
may not work as expected.
DVD (DVD player)
Manufacturer Control code
Aiwa 5010
Akai 5019
Apex 5015, 5016
CyberHome 5027
Denon 5017, 5020
GE 5003
Hitachi 5009
Integra 5001, 5002
Integra Research 5001, 5002
JVC 5023
Kenwood 5017
Magnavox 5004, 5021
Marantz 5025, 5026
Mitsubishi 5005
Onkyo 5001, 5002
Panasonic 5011, 5017, 5020
Philips 5004, 5021, 5028
Pioneer 5006
Proscan 5003
RCA 5003
Sanyo 5012
Sony
5007, 5013, 5018,
5029
Technics 5020
Thomson 5022, 5024
Toshiba 5008, 5021
Xbox 5022
Yamaha 5020
Zenith 5014, 5021
SAT (satellite receiver)
Manufacturer Control code
Alba 4014, 4017, 4025, 4027
Allsat 4015, 4027
Alltech 4022, 4025
Amstrad
4013, 4019, 4025, 4030,
4031
Anglo 4025
Ankaro 4025
Anttron 4017
Apollo 4017
Arcon 4016
Armstrong 4013
Asat 4016
Astra 4013, 4016, 4024
Astro 4019, 4020
AudioTon 4015
Bush 4012, 4014
Condor 4024
Conrad 4024
Cosat 4015, 4023
Crown 4013
Daewoo 4016, 4017, 4025
Diamond 4022
Dishnet 4008
Dual 4016
Echostar 4010, 4018, 4025
Einhell 4013, 4017, 4025
Elta 4015, 4017
Engel 4025
Eurosat 4013, 4022
Eurosky 4013, 4024
Eurostar 4024
Fagor 4015, 4023
Ferguson 4012
Fidelity 4030
Fracarro 4017
FTE 4025, 4030
Fuba 4017
Galaxis 4015, 4023
GE 4001, 4002
General Instruments 4003
GMI 4013
Grundig 4021, 4029, 4031
Hinari 4017
Hirschmann 4019, 4035
Hitachi 4036, 4037
Hughes Network
Systems
4011
Huth 4013, 4015, 4024
Imperial 4014
Intertronic 4013
Intervision 4015, 4023, 4024
Johansson 4015
JVC 4009, 4021
Kathrein 4025
Kolon 4017
K-SAT 4025
Kyostar 4017
Lasat 4013, 4020, 4024
Lenco 4016, 4017, 4025
Lennox 4023
Loewe 4013
Lorenzen 4024
Macab 4022
Manhattan 4015, 4020, 4023
Maspro 4021, 4025
Matsui 4021
Mediamarkt 4013
Medion 4025
Metronic 4013, 4017, 4020
Micro Technology 4025
Minerva 4021
Morgan’s 4013, 4015, 4025
Mysat 4025
Neuhaus 4019, 4023, 4024, 4025
Neusat 4025
SAT (satellite receiver)
Manufacturer Control code
Nikko 4013, 4025, 4027
Nokia 4033
Nordmende 4017, 4020
Oceanic 4022
Octagon 4016, 4017
Okano 4013
Optex 4015, 4023
Orbit 4016
Orbitech 4017, 4019
Pace 4012, 4026, 4031
Pacific 4022
Palladium 4013, 4017, 4021
Palsat 4019
Panasonic 4006, 4031
Panda 4024
Philips 4021, 4029
Phonotrend 4015, 4023
Predki 4017
Premier 4023
Primestar 4007
Proscan 4001, 4002
Protek 4022
Pye 4021
Quelle 4024
Radix 4035
RCA 4001, 4002
Roadster 4025
Rover 4025
Saba 4014, 4020, 4024, 4027
Samsung 4017
Satcom 4024
SatPartner 4017, 4020, 4027, 4030
Schneider 4029
Sedea Electronique 4017
Seemann 4013
SEG 4017, 4028
Seleco 4015, 4023
Skymaster 4025, 4034
Skyvision 4015
Sony 4005, 4031
Strong 4016, 4017, 4020
Sunstar 4013
Techniland 4015, 4023
TechniSat 4019
Teco 4013, 4016
Teleciel 4027
Telefunken 4017
Teleka 4013
Telemaster 4020
Telewire 4015, 4023
Tensai 4016
Thomson 4024, 4025
Thorens 4022
Tonna 4015, 4023, 4025
Toshiba 4004
Triasat 4019
SAT (satellite receiver)
Manufacturer Control code
81
Controlling Other Components
—Continued
SAT (satellite receiver)
Manufacturer Control code
Tristar
4016
Unisat
4013
Universum 4021, 4024
Vortec 4017
Wela 4025
Zehnder 4020
Zenith 4032
CBL (cable receiver)
Manufacturer Control code
ABC 3001, 3002, 3021
Archer 3006
Cabletime 3028, 3032
Cableview 3004
Contec 3009
Eastern 3010
GE 3001, 3002
Gemini 3011
General Instruments 3002, 3022
Grundig 3031
Hamlin 3012
Hitachi 3002
Jerrold
3002, 3011, 3013, 3021,
3022, 3023, 3026
Magnavox 3014
Memorex 3015
Movie Time 3016
NEC 3003
Nokia 3033
NSC 3016
Oak 3009
Panasonic 3020
Philips 3007, 3008, 3014
Pioneer 3017, 3024
Proscan 3001, 3002
RCA 3004, 3020, 3022
Realistic 3006
Sagem 3034
Salora 3029
Samsung 3017
Signature 3002
Sprucer 3020
Standard
Component
3018
Starcom 3011, 3021
Stargate 3011
Tele+1 3030
Tocom 3013
United Cable 3021, 3023
Universal 3005, 3006
Videoway 3025
View Star 3009, 3014, 3016
Zenith 3019
VCR
Manufacturer Control code
Aiwa 2012, 2046, 2047
Akai 2003, 2004, 2022
Alba
2033, 2041, 2044, 2045,
2047
Anitech 2033
ASA 2034
Baird 2036
Bell & Howell 2007
Blaupunkt 2039, 2042
Bush
2033, 2041, 2044, 2045,
2047
Canon 2010, 2011
Carver 2014
Cimline 2033
Citizen 2008, 2009
Colortyme 2005
Craig 2008
Crown 2033
Curtis Mathes
2001, 2005, 2008, 2009,
2010, 2011, 2023, 2026
Cyrus 2034
Daewoo 2012
Dansai 2033
Decca 2034
Dimensia 2001, 2026
Dumont 2034, 2036, 2037
Elcatech 2033
Emerson 2003, 2010, 2012, 2022
ESC 2043
Ferguson 2035
Finlandia 2034, 2036
Finlux 2034, 2036, 2037
Firstline 2033, 2041
Fisher 2007, 2030, 2036
Fuji 2004, 2010, 2024
Funai 2012
Garrard 2012
GE
2001, 2002, 2008, 2010,
2011, 2023, 2025, 2026
GEC 2034
GoldHand 2033
GoldStar 2005, 2009
Goodmans 2031, 2033
Gradiente 2012
Graetz 2036, 2043
Granada 2030, 2034, 2036
Grandin 2033
Grundig
2029, 2033, 2034, 2039,
2040, 2042, 2044
Harman Kardon 2005
HCM 2033, 2044
Hinari
2028, 2033, 2043, 2044,
2047
Hitachi
2013, 2021, 2025, 2028,
2037, 2038, 2043
Ingersol 2028
Interfunk 2034
ITT 2030, 2036, 2043, 2048
JC Penney
2005, 2006, 2007, 2008,
2010, 2011, 2013, 2014,
2021
Jensen 2013
JVC
2005, 2006, 2007, 2009,
2032, 2035, 2040, 2048
Kaisui 2033
Kendo 2041, 2046
Kenwood 2005, 2006, 2007, 2009
Kodak 2010
Loewe 2028, 2034
Logik 2028, 2043
Luxor 2030, 2031, 2036
Magnavox
2010, 2011, 2014, 2019,
2020
Marantz
2005, 2006, 2007, 2009,
2010, 2014, 2031, 2034
Matsui 2028, 2041, 2046, 2047
Matsushita 2010
Memorex
2007, 2008, 2010, 2012,
2019, 2030, 2036
Metz 2039
MGA 2022
Minerva 2039
Minolta 2013, 2021
Mitsubishi 2013, 2022, 2032, 2034
Motorola 2010
MTC 2008
Multitech 2008, 2012, 2033
NEC
2005, 2006, 2007, 2009,
2032
Neckermann 2034
Nesco 2033
NOBLEX 2008
Nokia 2030, 2036, 2043
Nordmende 2048
Okano 2046
Olympus 2010
Optonica 2017
Orion
2028, 2041, 2045, 2046,
2047
Osaki 2033
Otto Versand 2034
Palladium 2033
Panasonic 2010, 2011, 2042
Pentax 2013, 2021, 2025, 2037
Pentex Research 2009
Philco 2010, 2011, 2014
Philips
2010, 2014, 2017, 2034,
2048
Phonola 2034
Pioneer 2006, 2013, 2032, 2034
Proline 2044
Proscan 2001, 2002, 2026
Pye 2034
Quasar 2010, 2011
Quelle 2034
Radio Shack 2017
Radio Shack/
Realistic
2007, 2008, 2010, 2011,
2012, 2017
Radiola 2034
VCR
Manufacturer Control code
82
Controlling Other Components
—Continued
VCR
Manufacturer Control code
RCA
2001, 2002, 2003, 2008,
2010, 2013, 2021, 2023,
2025, 2026, 2027
Realistic
2007, 2008, 2010, 2011,
2012, 2017
Rex 2048
Roadstar 2033, 2043
Runco 2019
Saba 2040, 2048
Saisho 2028, 2041
Salora 2030
Samsung 2008, 2043, 2049
Sansui 2006, 2032
Sanyo 2007, 2008, 2030, 2036
Saville 2047
SBR 2034
Schaub Lorenz 2036
Schneider 2033, 2034
Scott 2015
Sears 2007, 2010, 2013, 2021
SEG 2043
SEI 2028, 2034
Sharp 2016, 2017, 2031
Shintom 2004, 2033, 2036
Shorai 2028
Siemens 2034, 2036, 2039
Singer 2010
Sinudyne 2028, 2034
Sonolor 2030, 2031
Sony 2004, 2018, 2024
STS 2010, 2021
Sunkai 2046
Sylvania 2010, 2011, 2012, 2014
Symphonic 2012
Tandy 2007
Tatung 2034
Teac 2012
Technics 2010, 2042
Teknika 2010, 2012
Telefunken 2048
Thomson 2048
Thorn 2035, 2036
Toshiba
2013, 2015, 2022, 2034,
2048
Totevision 2008
Uher 2043
Unitech 2008
Universum 2034, 2039, 2043
Vector Research 2005, 2006
Video Concepts 2005, 2006, 2022
Wards
2008, 2010, 2012, 2013,
2017, 2021, 2027
XR-1000 2010, 2012
Yamaha 2005, 2006, 2007, 2009
Yoko 2043
Zenith 2004, 2019, 2024
TV
Manufacturer Control code
Admiral 1026, 1040, 1062
Akai 1002, 1067
Akura 1045
Alba 1035, 1043
Amplivision 1063
Amstrad 1035, 1067
Amtron 1009
Anam National 1003, 1009
Anitech 1035
AOC 1004, 1005, 1006
Arc en Ciel 1066
Arcam 1063
ASA 1040
Audiovox 1009
Autovox 1040, 1068
Baird 1069
Bang & Olufsen 1040
Baur
1036, 1054, 1055, 1058,
1059, 1068
Beko 1052
Bell & Howell 1010, 1017
Binatone 1063
Blaupunkt
1041, 1042, 1044, 1058,
1059
Boots 1063
Brionvega 1040
Bruns 1040
BSR 1048
Bush
1035, 1043, 1048, 1050,
1053, 1057
Cascade 1035
Celebrity 1002
Century 1040
Cimline 1035, 1043
Citizen
1004, 1006, 1009, 1017,
1022, 1025
Clatronic 1052
Colortyme 1004, 1006
Condor 1052
Contec 1035
Contec/Cony 1007, 1009
Continental Edison 1066
Craig 1009
Crosley 1040
Crown 1009, 1014, 1035, 1052
Curtis Mathes
1001, 1004, 1006, 1010,
1017, 1022, 1025, 1034
Daewoo
1004, 1005, 1006, 1025,
1035, 1053
Daytron 1004, 1006, 1025, 1035
Decca 1067
Dimensia 1001, 1034
Dixi 1035
Dual 1057, 1068
Dumont 1004, 1039, 1040
Electroband 1002
Electrohome
1002, 1003, 1004, 1006,
1008
Elta 1035
Emerson
1004, 1006, 1007, 1009,
1010, 1017, 1025, 1027,
1029, 1033, 1040, 1070
Envision 1004, 1006
Erres 1037
Europhon 1067
Fidelity 1068
Finlux 1039, 1040, 1067
Firstline
1035, 1043, 1048, 1049,
1063
Fisher
1010, 1017, 1052, 1063,
1068
Formenti 1040
Frontech 1045, 1062
Fujitsu 1070
Funai 1009, 1045, 1048, 1070
GE
1001, 1003, 1004, 1006,
1011, 1012, 1019, 1034
GEC 1038, 1063, 1067, 1069
Geloso 1035
Genexxa 1062
GoldStar
1004, 1005, 1006, 1007,
1008, 1025, 1047, 1063
Goodmans 1043, 1053, 1063
Gorenje 1052
Graetz 1062, 1069
Granada 1063, 1067
Grundig
1039, 1041, 1042, 1058,
1059, 1064
Hallmark 1004, 1006
Hanseatic 1060, 1068
Hantarex 1067
HCM 1035
Hinari 1035, 1043
Hitachi
1004, 1006, 1007, 1013,
1027, 1038, 1062, 1063,
1069
Huanyu 1053
ICE 1045, 1063
Imperial 1052
Infinity 1014
Inno Hit 1056, 1067
Interfunk 1055, 1062, 1066, 1069
Intervision 1045, 1063
ITT 1062, 1068, 1069
JBL 1014
JC Penney
1001, 1004, 1005, 1006,
1011, 1012, 1016, 1019,
1022, 1025, 1034
Jensen 1004, 1006
JVC
1007, 1012, 1013, 1015,
1033
Kaisui 1035, 1063
Kapsch 1062, 1069
Kathrein 1060
Kawasho 1002, 1004, 1006
Kendo 1043
Kenwood 1004, 1006, 1008
Kloss Novabeam 1009
Korting 1040
KTV 1009, 1025
LG 1005
TV
Manufacturer Control code
83
Controlling Other Components
—Continued
TV
Manufacturer Control code
Loewe 1014, 1040, 1055
Luxman 1004, 1006
LXI
1001, 1006, 1010, 1014,
1016, 1017, 1034
M Electronic 1035, 1053, 1062, 1063
Magnadyne 1040, 1067, 1068
Magnafon 1067
Magnavox
1004, 1006, 1008, 1014,
1018, 1020
Marantz 1004, 1006, 1014, 1060
Matsui
1035, 1043, 1048, 1050,
1063, 1064, 1067, 1068
Megatron 1006
Memorex
1005, 1006, 1010, 1017,
1035
Metz 1040, 1051, 1058
MGA 1004, 1005, 1006, 1008
Minerva 1039, 1058, 1059, 1064
Mitsubishi
1004, 1005, 1006, 1008,
1040, 1055, 1058
Mivar 1047, 1056, 1067
Motorola 1003, 1026
MTC
1004, 1005, 1006, 1022,
1055
Multitech 1009, 1035
NAD 1006, 1016
NEC 1003, 1004, 1005, 1006
Neckermann
1040, 1041, 1054, 1059,
1060
Nikkai 1045
Nikko 1006
Oceanic 1062
Onwa 1009
Optonica 1021, 1026
Orion
1029, 1043, 1048, 1049,
1050, 1067, 1068
Osaki 1045, 1063
Otto Versand
1036, 1041, 1043, 1054,
1055, 1058, 1059, 1060,
1063
Palladium 1052
Panasonic
1003, 1012, 1014, 1031,
1044, 1046, 1051, 1061,
1062, 1069
Pathe Marconi 1066
Philco
1003, 1004, 1005, 1006,
1007, 1008, 1014, 1018,
1040
Philips
1003, 1004, 1007, 1008,
1014, 1018, 1019, 1020,
1037, 1038, 1040, 1053,
1059, 1060
Phoenix 1040
Phonola 1037, 1040
Pioneer 1004, 1006, 1027, 1062
Portland 1004, 1005, 1006, 1025
Price Club 1022
Prism 1012
Profex 1035
Proline 1049
Proscan 1001, 1034
Protech 1035, 1045, 1063
Proton 1004, 1006, 1007
Pye 1037
Quasar 1003, 1012, 1031
Quelle
1036, 1039, 1054, 1055,
1058, 1059, 1068
Radio Shack 1010, 1017, 1034
Radio Shack/
Realistic
1001, 1004, 1006, 1007,
1009, 1010, 1017, 1021,
1025
Radiola 1037
Radiomarelli 1040, 1067
RCA
1001, 1003, 1004, 1005,
1006, 1008, 1027, 1034
Realistic 1010, 1017, 1034
Rex 1045, 1062
RFT 1040
Roadstar 1035, 1045
Saba 1040, 1062, 1066, 1069
Saisho
1035, 1043, 1045, 1067,
1068
Salora 1062
Sambers 1056, 1067
Sampo 1004, 1006, 1025
Samsung
1004, 1005, 1006, 1007,
1008, 1022, 1025, 1035,
1045, 1047, 1052, 1056,
1060, 1063, 1065
Sansui 1029
Sanyo 1004, 1010, 1017
SBR 1037, 1038
Schaub Lorenz 1069
Schneider 1068
Scott
1004, 1006, 1007, 1009,
1070
Sears
1001, 1004, 1006, 1008,
1010, 1015, 1016, 1017,
1028, 1034, 1070
SEG 1045, 1063
SEI
1036, 1040, 1048, 1067,
1068
Seleco 1062
Sharp
1004, 1006, 1007, 1021,
1023, 1025, 1026
Shorai 1048
Siarem 1040, 1067
Siemens 1041, 1042, 1058, 1059
Singer 1040
Sinudyne
1036, 1040, 1043, 1067,
1068
Solavox 1062
Sonoko 1035
Sonolor 1062
Sony
1002, 1030, 1032, 1036,
1054
Soundesign 1004, 1006, 1009, 1070
Starlite 1009
Stern 1062
Sunkai 1043, 1048, 1049, 1050
Sylvania
1004, 1006, 1008, 1014,
1018, 1020
Symphonic 1009, 1028
Tandy 1026, 1062, 1063
Tashiko 1038, 1063
Tatung 1003, 1063, 1067
Tec 1063
TV
Manufacturer Control code
Technics 1012, 1044, 1061
Techwood 1004, 1006, 1012
Teknika
1004, 1005, 1006, 1007,
1009, 1022, 1025, 1031,
1070
Teleavia 1066
Telecaption 1024
Telefunken 1066
Teletech 1035
Teleton 1063
Tensai 1048
Thomson 1066
Thorn 1054, 1055, 1058
Toshiba
1010, 1016, 1017, 1022,
1024, 1039
Totevision 1025
Triumph 1067
Universal 1011, 1019
Universum 1045, 1052, 1058
Voxson 1040, 1062
Waltham 1063
Wards
1001, 1004, 1005, 1006,
1008, 1011, 1014, 1018,
1019, 1020, 1021, 1034,
1070
Watt Radio 1068
Wega 1040
Yamaha 1004, 1005, 1006, 1008
Yoko 1045, 1063
Zenith 1004
TV
Manufacturer Control code
84
Controlling Other Components
—Continued
To control another component, point the remote control-
ler at it and use the buttons as explained below (you must
select the appropriate remote control mode rst).
Controlling a TV
Buttons marked with an asterisk can always be used to
control a TV regardless of the currently selected
remote controller mode.
The following buttons control the AV Receiver.
[VOL]: Adjusts the volume of the AV receiver.
[MUTING]: Mutes the AV Receiver.
Controlling a Cable Receiver
The following buttons control the AV Receiver.
[VOL]: Adjusts the volume of the AV receiver.
[MUTING]: Mutes the AV Receiver.
[ON], [STANDBY]
Set the TV to On or Standby
TV [ ]
Turn the TV On or Off
Number buttons
Enter numbers
[CH +/]
Select channels on the TV
[TV INPUT]
Select inputs on the TV
VOL [ ]/[ ]
Adjust the TV’s volume
CH
TV INPUT
TV CH +/
VOL
ON
*
*
*
*
STANDBY
TV VOL
TV
Number
buttons
Press [TV]
rst
*
[ON], [STANDBY]
Set the cable receiver to On or
Standby
[CH +/]
Select cable channels
Number buttons
Enter numbers
CH
ON
STANDBY
Number
buttons
Press
[CABLE]
rst
85
Controlling Other Components
—Continued
Controlling a VCR
The following buttons control the AV Receiver.
[VOL]: Adjusts the volume of the AV receiver.
[MUTING]: Mutes the AV Receiver.
Controlling a Satellite Receiver
The following buttons control the AV Receiver.
[VOL]: Adjusts the volume of the AV receiver.
[MUTING]: Mutes the AV Receiver.
[ON], [STANDBY]
Set the VCR to On or Standby
[CH +/]
Selects channels on the VCR
[]
Play
[]
Stop
[]
Rewind
[]
Fast forward
[]
Pause
REC [ ]
Record
CH
REC
ON
STANDBY
,
Press
[VCR] rst
[ON], [STANDBY]
Set the satellite receiver to On or
Standby
[CH +/]
Select satellite channels
[ ]/[ ]/[ ]/[ ]
Select menu items
[ENTER]
Confirm selection
Number buttons
Enter numbers
CH
ENTER
ON
STANDBY
Number
buttons
Press [SAT]
rst
86
Controlling Other Components
—Continued
The AV receivers remote controller can learn the com-
mands of other remote controllers simply by pointing
them at each other. For example, by transmitting the Play
command from your CD players remote controller, the
remote controller can learn it and then transmit the same
command when its Play [ ] button is pressed in CD
mode.
This is convenient when you want to add commands to
buttons after entering a remote control code (page 78).
Notes:
The following buttons cannot be taught new com-
mands: REMOTE MODE, MACRO [1], [2], [3], TV
[ ], TV [INPUT], TV CH [+]/[], TV VOL [ ]/
[].
The AV receivers remote controller can learn up to
approximately 150 commands. However, the com-
mands of some remote controllers may use a lot of
memory, which will decrease the number of com-
mands that can be learned.
By default, the AV receivers remote controller knows
the commands for controlling an Onkyo CD player,
cassette deck, DVD player, and MD player (e.g., Play,
Stop, Pause, etc., buttons). These buttons can learn
new commands, although the defaults will be restored
if the remote controller is reset.
To learn a new command for a button that has already
learned one, simply repeat this procedure.
Like most remote controllers, the AV receivers
remote controller uses infrared. Commands from
remote controllers that dont use infrared cannot be
learned.
When the remote controllers batteries expire, all
learned commands will be lost and will have to be
learned all over again, so dont discard your other
remote controllers.
Learning Commands from Another
Remote Controller
1
While holding down the REMOTE
MODE button that you want to
learn the command, press the
[ON] button.
2
On the AV receivers remote con-
troller, press the button you want
to learn the new command.
1
1, 4
ON
3
Point the remote controllers at
each other, about 2 to 6 inches
(515 cm) apart, and then, on the
other remote controller, press the
button whose command you
want to learn.
4
To teach the AV receivers remote
controller more new commands,
repeat steps 2 and 3.
Press the [ON] button when youve n-
ished.
P
O
W
E
R
S
L
E
E
P
D
IMM
E
R
S
U
R
M
O
D
E
V
ID
E
O
-
1
V
IDE
O
-
2
T
A
P
E
D
V
D
C
D
C
D
D
V
D
T
UN
E
R
T
U
NE
R
P
H
ON
O
IN
P
U
T
S
E
L
E
C
T
O
R
DI
S
C
T
A
P
E
V
O
L
U
M
E
L
E
V
E
L
C
H
S
E
L
P
R
E
S
E
T
M
U
TI
N
G
T
E
S
T
T
O
N
E
M
U
LT
I-CH
IN
PUT
G
R
O
U
P
R
O
N
S
T
A
N
D
B
Y
T
V
TV
C
H
T
V
V
O
L
-
-
/
-
-
-
S
L
E
E
P
IN
P
U
T
I
S
A
T
C
A
BL
E
D
V
DC
D
+
10
0
CLEAR
1
2
3
45
6
7
8
9
+
-
M
A
C
R
O
1
2
3
M
D
/C
D
R
I
N
P
U
T
S
E
L
E
C
T
O
R
V
1
V
2
V
3
C
D
TA
P
E
V
4
D
V
D
M
U
L
TI CH
T
U
N
E
R
R
E
M
O
T
E
M
O
D
E
About 2 to 6
inches (5–15 cm)
87
Controlling Other Components
—Continued
With the Macro function, you can program the remote
controllers MACRO buttons to perform a sequence of
actions with just one button press. For example, nor-
mally you need to perform the following actions to play
a CD:
1. Press the REMOTE MODE [RECEIVER] button
to select Receiver mode.
2. Press the [ON] button to turn on the AV receiver.
3. Press the [CD] INPUT SELECTOR button to
select the CD input source.
4. Press the REMOTE MODE [CD] button to select
the CD remote controller mode.
5. Press the Play [ ] button to start playback on the
CD player.
With the Macro function, you can program one of the
MACRO buttons to perform all ve actions.
Making Macros
There are three MACRO buttons, and each button can be
programmed with a different macro in each remote con-
troller mode. Each macro can perform up to eight
actions.
Note:
If after programming a macro you teach one of the but-
tons in that macro a new command, then the macro will
no longer work properly. In this case, you must program
the macro again.
Running Macros
Programmed macros can be run as follows.
Using Macros
1
While holding down the REMOTE
MODE button for the mode that
you want to learn the macro,
press MACRO button [1], [2], or
[3].
The Remote indicator lights up.
1
1
2
On the remote controller, press
the buttons whose actions you
want to program into the macro
in the order you want them per-
formed.
For example, to program the previous
CD example into a macro, press the fol-
lowing buttons: REMOTE MODE
[RECEIVER], [ON], INPUT SELEC-
TOR [CD], REMOTE MODE [CD],
Play [ ].
3
When youve nished, press the
MACRO button again.
1
Press the MACRO [1], [2], or [3]
button.
The actions in the macro are performed
in the order in which they were pro-
grammed.
88
Specifications
Amplifier Section
Video Section
Tuner Section
FM
AM
General
Video Inputs
Video Outputs
Audio Inputs
Audio Outputs
Other Jacks
Specifications and features are subject to change without
notice.
Power Output
2 channel driven: North American:
90 W + 90 W
(8
, 20 Hz–20 kHz, FTC)
European: 125 W + 125 W
(6
, 1 kHz, DIN)
Asian, Australian: 155 W + 155 W
(6
, 1 kHz, JEITA)
Dynamic Power 225 W + 225 W (3
, Front)
175 W + 175 W (4
, Front)
105 W + 105 W (8
, Front)
THD (Total Harmonic
Distortion) 0.08 % (Power Rated)
Damping Factor 60 (Front, 1 kHz, 8
)
Input Sensitivity and
Impedance 200 mV/47 k
(LINE)
Output Level and
Impedance 200 mV/470
(REC OUT)
Frequency Response 10 Hz–100 kHz/+1 dB-3 dB (Direct
mode)
Tone Control ±10 dB, 50 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
SN Ratio 106 dB (LINEIHF-A)
Speaker Impedance North American: 6
Others: 4
Input Sensitivity/Output
Level and Impedance 1 Vp-p/75
(Component and S-Video Y)
0.7 Vp-p/75
(Component Pb/Cb, Pr/Cr)
0.28 Vp-p/75
(S-Video C)
1 Vp-p/75
(Composite)
Component Video
Frequency Response 5 Hz – 50 MHz
Tuning Frequency Range
North American: 87.5 MHz– 107.9 MHz
Others: 87.5 MHz– 108.0 MHz
Usable Sensitivity Stereo: 17.2 dBf 2 µV (75
IHF)
Mono: 11.2 dBf 1 µV (75
IHF)
S/N Ratio Stereo: 70 dB (IHF-A)
Mono: 76 dB (IHF-A)
THD Stereo: 0.3 % (1 kHz)
Mono: 0.2 % (1 kHz)
Frequency Response 30 Hz–15 kHz / ±1 dB
Stereo Separation 45 dB (1kHz)
Tuning Frequency Range
North American: 530 kHz–1710 kHz
European: 522 kHz-1611 kHz
Others: 530/522 kHz–1710/1611 kHz
Usable Sensitivity 30 µV
S/N Ratio 40 dB
THD 0.70%
Power Supply North American: AC 120 V, 60 Hz
Australian and European: AC 230-240 V,
50 Hz
Others: AC 120/220-230 V, 50/60 Hz
AC 230-240 V, 50 Hz
AC 220-230 V, 50/60 Hz
Power Consumption North American: 7A
Others: 630 W
Stand-by Power
Consumption North American: 0.1 W
European: 0.2 W
Others: 0.5 W
Dimensions (W x H x D) 435 W x 174 H x 377 D mm
17-1/8" W x 6-7/8" H x 14-13/16" D inches
Weight North American and
European: 11.0 kg
24.3 lbs
Others: 11.1 kg
24.5 lbs
Component Video Input 1,2,3
S-Video Compatible Jack
Input DVD, VIDEO1, VIDEO2, VIDEO3,
VIDEO4
A/V Input DVD, VIDEO1, VIDEO2, VIDEO3,
VIDEO4
Component Video
Output OUT
S-Video Compatible Jack
Output MONITOR OUT, VIDEO1, VIDEO2
A/V Output MONITOR OUT, VIDEO1, VIDEO2
Digital Inputs Optical: 4
Coaxial: 2
Analog Inputs DVD(MULTICHANNEL), VIDEO1,
VIDEO2, VIDEO3, VIDEO4, TAPE, CD
Multichannel Inputs 6
Digital Outputs Optical: 1
Analog Outputs TAPE, VIDEO1, VIDEO2, ZONE2
Subwoofer Pre Outputs 1
Speaker Outputs 9
Phones 1
IR Input 1
12V Trigger Out 1
89
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you cant resolve the issue
yourself, contact your Onkyo dealer.
Cant turn on the AV receiver?
Make sure that the power cord is properly plugged
into the wall outlet.
Unplug the power cord from the wall outlet, wait ve
seconds or more, then plug it in again.
The AV receiver turns off as soon as its turned
on?
The amp protection circuit has been activated.
Remove the power cord from the wall outlet immedi-
ately and contact your Onkyo dealer.
Theres no sound, or its very quiet?
Make sure that all audio connecting plugs are pushed
in all the way (page 21).
Make sure that the inputs and outputs of all compo-
nents are connected properly (page 21).
Make sure that the polarity of the speaker cables is
correct, and that the bare wires are in contact with the
metal part of each speaker terminal (page 23).
Make sure that the input source is properly selected
(page 53).
Make sure that the speaker cables are not shorting.
Check the volume. It can be set to MIN, 1 through 99,
or MAX (page 53). The AV receiver is designed for
home theater enjoyment. It has a wide volume range,
allowing precise adjustment.
If the MUTING indicator is shown on the display,
press the remote controllers [MUTING] button to
unmute the AV receiver (page 54).
While a pair of headphones is connected to the
PHONES jack, no sound is output by the speakers
(page 54).
Check the digital audio output setting on the con-
nected device. On some game consoles, such as those
that support DVD, the default setting is off.
With some DVD-Video discs, you need to select an
audio output format from a menu.
If your turntable doesnt have a built-in phono
preamp, you must connect one between it and the AV
receiver. If your turntable uses an MC cartridge, you
must connect an MC head amp, or an MC transformer
and phono equalizer.
Make sure that none of the connecting cables are bent,
twisted, or damaged.
Not all listening modes use all speakers (page 62).
Specify the speaker distances (page 49) and adjust the
individual speaker levels (page 50).
Make sure that the speaker setup microphone is not
still connected.
Only the front speakers produce sound?
When the Stereo listening mode is selected, only the
front speakers and subwoofer produce sound.
When the Direct or Pure Audio (not all models) listen-
ing mode is selected, only the front speakers produce
sound.
Make sure the speakers are congured correctly
(page 46).
Only the center speaker produces sound?
If you use the Pro Logic IIx Movie or Pro Logic IIx
Music listening mode with a mono source, such as an
AM radio station or mono TV program, the sound is
concentrated in the center speaker.
Make sure the speakers are congured correctly
(page 46).
The surround speakers produce no sound?
When the Stereo, Direct, or Pure Audio (not all mod-
els) listening mode is selected, the surround speakers
produce no sound (page 62).
Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
Make sure the speakers are congured correctly
(page 46).
The center speaker produces no sound?
When the Mono or Stereo listening mode is selected,
the center speaker produces no sound (page 62).
Make sure the speakers are congured correctly
(page 46).
The surround back speakers produce no
sound?
The surround back speakers are not used with all lis-
tening modes. Select another listening mode
(page 62).
Not much sound may be produced by the surround
back speakers with some sources.
Make sure the speakers are congured correctly
(page 46).
Power
Audio
90
Troubleshooting
—Continued
The subwoofer produces no sound?
When you play source material that contains no infor-
mation in the LFE channel, the subwoofer produces
no sound.
Make sure the speakers are congured correctly
(page 46).
Theres no sound with a certain signal format?
Check the digital audio output setting on the con-
nected device. On some game consoles, such as those
that support DVD, the default setting is off.
With some DVD-Video discs, you need to select an
audio output format from a menu.
Depending on the input signal, some listening modes
cannot be selected (page 61).
Cant select the DTS-ES Discrete/Matrix listen-
ing modes?
These modes cannot be selected when no surround
back speakers are connected, or the Zone 2 speakers
are being used.
You can not always select all of the listening modes,
depending on the number of the speaker connected
(page 61).
Cant get 6.1 playback?
If no surround back speakers are connected, or the
Zone 2 speakers are being used, 6.1 playback is not
possible.
You can not always select all of the listening modes,
depending on the number of the speakers connected
(page 61).
The volume cannot be set to 99?
When the levels of all speakers have been calibrated
(page 50), the maximum volume setting may change.
Noise can be heard?
Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so dont do it.
An audio cable may be picking up interference. Try
repositioning your cables.
The Late Night function doesnt work?
Make sure the source material is Dolby Digital
(page 64).
The DVD analog multichannel input doesnt
work?
Check the DVD analog multichannel input connec-
tions (page 29).
To select the DVD analog multichannel input, press
the [MULTI CH] input selector button.
Check the audio output settings on your DVD player.
About DTS signals
When DTS program material ends and the DTS bit-
stream stops, the AV receiver remains in DTS listen-
ing mode and the DTS indicator remains on. This is to
prevent noise when you use the pause, fast forward, or
fast reverse function on your player. If you switch
your player from DTS to PCM, because the AV
receiver does not switch formats immediately, you
may not hear any sound, in which case you should
stop your player for about three seconds, and then
resume playback.
With some CD and LD players, you wont be able to
playback DTS material properly even though your
player is connected to a digital input on the AV
receiver. This is usually because the DTS bitstream
has been processed (e.g., output level, sampling rate,
or frequency response changed) and the AV receiver
doesnt recognize it as a genuine DTS signal. In such
cases, you may hear noise.
When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a mal-
function.
Theres no picture?
Make sure that all video connecting plugs are pushed
in all the way (page 21).
Make sure that each video component is properly con-
nected.
If your video component is connected to a component
video input, your TV must be connected to the com-
ponent video output (page 26).
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
While the Pure Audio listening mode (not all models)
is selected, the video circuits are turned off and the AV
receiver outputs no video signals.
The onscreen menus dont appear?
Make sure that the video settings are correct
(page 44).
On your TV, make sure that the video input to which
the AV receiver is connected is selected.
Video
91
Troubleshooting
—Continued
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesnt
appear?
Relocate your antenna.
Move the AV receiver away from your TV or com-
puter.
Listen to the station in mono (page 56).
When listening to an AM station, operating the remote
controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
The remote controller doesnt work?
Make sure that the batteries are installed with the cor-
rect polarity (page 13).
Install new batteries. Dont mix different types of bat-
teries, or old and new batteries (page 13).
Make sure that the remote controller is not too far
away from the AV receiver, and that theres no
obstruction between the remote controller and the AV
receivers remote control sensor (page 13).
Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type uorescent lights.
Relocate if necessary.
If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not
work reliably when the doors are closed.
Make sure youve selected the correct remote control-
ler mode (pages 14-19).
When using the remote controller to control other
manufacturers AV components, some buttons may
not work as expected.
Make sure youve entered the correct remote control
code.
Make sure to set the same ID on both the AV receiver
and remote controller (pages 72 and 73).
Cant control other components?
If its an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an cable wont work (page 37).
Make sure youve selected the correct remote control-
ler mode (pages 14-19).
If you connect an MD recorder or CD recorder to the
TAPE jacks, be sure to make the necessary setting
(pages 52 and 78).
When learning commands, make sure that the trans-
mitting ends of both remote controllers are pointing at
each other.
Are you trying to learn from a remote controller that
cannot be used for learning? Some commands cannot
be learned, especially those that transmit several
instructions with a single button press.
The wrong remote control code has been entered.
The entered remote control code may not be correct.
If more than one code is listed, try each one.
With some AV components, certain buttons may not
work as expected, and some may not work at all.
To control Onkyo components, point the remote con-
troller at the AV receiver.
To control another manufacturers component, point
the remote controller at that component.
Cant record?
On your recorder, make sure the correct input is
selected (e.g., digital or analog).
Zone 2 has turned off?
Was the Sleep function set? The Sleep function turns
off Zone 2 as well as the AV receiver. To set the Sleep
function for Zone 2 only, see page 76.
Theres no sound?
Only components connected to analog inputs can be
played in Zone 2.
Tuner
Remote Controller
Recording
Zone 2
92
SN 29343945
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.ch.onkyo.com/
(C) Copyright 2005 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 3 9 4 5 *
http://www.onkyo.com/
HOMEPAGE
D0504-1
Troubleshooting
—Continued
The sound changes when I connect my head-
phones?
When a pair of headphones is connected, the listening
mode is set to Stereo, unless its already set to Stereo,
Direct, or Pure Audio (not all models). When you dis-
connect the headphones, the previous listening mode
will be resumed.
The speaker volume cannot be set as required?
When the Automatic Speaker Setup function is used,
or the volume is adjusted on the onscreen setup
menus, the maximum possible volume setting may
change.
The speaker distance cannot be set as
required?
In some cases, corrected values suitable for home the-
ater use may be set automatically.
The display doesnt work?
The display is turned off when the Pure Audio (not all
models) listening mode is selected.
Actions are not displayed on the TV or projector thats
connected to the COMPONENT VIDEO OUT.
How do I change the language of a multiplex
source?
Use the a. Multiplex setting on the 4. Audio
Adjust menu to select Main or Sub (page 69).
The functions Auto Power On/Standby and
Direct Change dont work for components con-
nected via ?
These functions dont work when Zone 2 is turned on.
Others
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Resetting the AV receiver to its factory defaults
To reset the AV receiver to its factory defaults, turn it on
and, while holding down the [VIDEO 1] button, press
the [STANDBY/ON] button. “CLEAR” will appear on the
display and the AV receiver will enter Standby mode.
The AV receiver uses a battery-less memory backup
system in order to retain radio presets and other set-
tings when it’s unplugged or in the case of a power fail-
ure. Although no batteries are required, the AV receiver
must be plugged into an AC outlet in order to charge the
backup system.
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
87

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Onkyo TX-SR8360 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Onkyo TX-SR8360 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info