553769
89
Verklein
Vergroot
Pagina terug
1/97
Pagina verder
89
Using the Macro Function—Continued
Perform the procedure below to execute the macro that
you have programmed into the remote controller. After
programming the macro, you should always run it at
least once to make sure that it has been programmed
properly.
Erasing a macro from the MACRO 1 (or 2) button
Notes:
If the SEND/LEARN indicator quickly flashes three
times and turns off, then the remote controller has
exited the erasing mode because either you have
made a mistake during erasing or a time-out has
occurred because no button was pressed. Resume
from Step 1.
If you press a button other than MACRO 1 (or 2) but-
ton in Step 2, then you will in effect be overwriting
the previous macro with a new macro.
Erasing all commands and macros that have
been programmed
This procedure will erase all the commands and macros
that you have programmed into the remote controller
and return it to its default settings. This operation will
not affect the preset settings of the remote controller.
All programmed commands and macros are erased and
the remote controller returns to its factory presets.
Notes:
Proceed to Step 3 immediately after Step 2; other-
wise, the batteries will be consumed quickly.
If you press any button other than the ENTER/ZONE
2 button in Step 3, nothing will be erased. In this
case, resume from Step 1.
Macro mode programming memo
Executing the Macro
1
Point the remote controller at the
TX-NR801/TX-NR801E.
2
Press the MACRO 1 (or 2) button.
It may take a while for the macro to finish trans-
mitting, so be sure to continue pointing the
remote controller at the device until the SEND/
LEARN indicator turns off.
1
Press and hold down any one of the 8
MODE buttons, press the MACRO 1 (or 2)
button, and then release both buttons.
When you press the MODE button, it lights and
the SEND/LEARN indicator lights. When you
press the MACRO 1 (or 2) button, the indicator
turns off. When you release the buttons, the indi-
cator flashes once.
2
Press the MACRO 1 (or 2) button again.
The SEND/LEARN indicator slowly flashes
twice. The macro programmed to the MACRO
button is erased.
1
Open the battery cover and remove the
batteries from the remote controller.
2
While pressing and holding down the ON
and STANDBY buttons, re-insert the bat-
teries in their correct orientation, and then
release both buttons.
The SEND/LEARN indicator flashes slowly.
3
Press the ENTER/ZONE 2 button.
The SEND/LEARN indicator lights up for about
ten seconds and then turns off.
MACRO 1 MACRO 2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
89

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Onkyo TX-NR801 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Onkyo TX-NR801 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info