686241
121
Verklein
Vergroot
Pagina terug
1/135
Pagina verder
121
Front Panel Rear Panel Remote
Contents
Connections
Playback
Setup
Troubleshooting
Power
Cannot turn on the unit
Make sure that the power cord is properly plugged into the wall outlet.
Unplug the power cord from the outlet once, wait 5 seconds or more, then plug it in again.
( p40)
The unit turns o unexpectedly
If “5. Hardware” - “Power Management” - “Auto Standby” on the Setup menu is activated, the unit automatically enters the standby mode.
The protection circuit function may have operated. In such a case, if the power is turned on again, “AMP Diag Mode” is displayed on the main
unit’s display, and the unit enters the diagnosis mode to check the unit for abnormality. As the result, if no problem is found, “AMP Diag Mode”
on the display disappears. Then, you can use the unit normally. If “CHECK SP WIRE” appears on the display, the speaker cables may be short-
circuited. Check if the core wire of a speaker cable is not in contact with the core wire of another speaker cable or the rear panel, and turn the
power on again If “NG” is displayed, remove the power plug from the outlet immediately, and consult the dealer.
The protection circuit function may have operated due to an abnormal rise in temperature of the unit. In such a case, the power turns o
repeatedly even if the power is turned on each time. Secure sucient ventilation space around the unit, wait for a while until the temperature of
the unit decreases. Then, turn the power on again.
WARNING: If smoke, smell or abnormal noise is produced by the unit, unplug the power cord from the outlet immediately, and contact the dealer or
Onkyo Support.
( p105)
Audio
Make sure that the speaker setup microphone is no longer connected.
Conrm that the connection between the output jack on the connected device and the input jack on this unit is correct.
Make sure that none of the connecting cables are bent, twisted, or damaged.
If the MUTE indicator on the display blinks, press on the remote controller to cancel muting.
While headphones are connected to the PHONES jack, no sound is output from the speakers.
When "Source" - "Audio Select" - "PCM Fixed Mode" in the Setup menu is set to "On", no sound is played if signals other than PCM are input.
Change the setting to O.
Check the following if the problem persists after you have conrmed the above.
No sound from the TV
Change the input selector on this unit to the position of the terminal to which the TV is connected.
If the TV does not support the ARC function, along with the connection by an HDMI cable, connect the TV with this unit using a digital optical
cable, digital coaxial cable, or analog audio cable.
( p32)
121

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Onkyo-TX-NR686

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Onkyo TX-NR686 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Onkyo TX-NR686 in de taal/talen: Engels als bijlage per email.

De handleiding is 8,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Onkyo TX-NR686

Onkyo TX-NR686 Gebruiksaanwijzing - Nederlands - 135 pagina's

Onkyo TX-NR686 Gebruiksaanwijzing - Deutsch - 135 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info