548134
8
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
8
Step 2:
Setting Up
5.
When the measurement is completed, the
measurement result is displayed.
AccuEQ Room Calibration
<-Review Speaker Configuration->
Subwoofer : Yes
Front : Small
Center : Small
Surround : Small
Crossover : 150 Hz
Save
Cancel
Press
d
/
c
on the remote controller to check the settings.
Pressing ENTER when "Save" is selected will save the
settings.
• The subwoofer sound may not be detected since
it is extremely low frequencies. If "No" is shown for
"Subwoofer" in the measurement result screen,
raise the subwoofer volume to around the half of
its maximum volume and make its frequency to the
maximum level.
6.
On the screen showing "AccuEQ" is "On", press
ENTER.
The settings will be applied to all the inputs.
7.
When "Please unplug setup microphone." is
displayed, disconnect the microphone.
•
If you change the speaker positions, the room furniture
layout or the number of speakers, perform automatic
speaker setting again.
• If there is an error message, follow the on-screen
instruction to remove the error cause.
3
Making Wi-Fi setting
Items to be checked before starting the procedure
Wi-Fi connection requires an access point such as
wireless LAN router (
). Write down the SSID and
password (key) of the access point if they are shown
in the label of the main body. If the access point has
an automatic setting button (may be called differently
according to the manufacturer), you can set up
without inputting the password. For how to use the
automatic setting button of the access point, refer to
its instruction manual.
The unit supports Wi-Fi connection with 2.4 GHz
access point.
Operation: You can set up by viewing the guidance
displayed on the TV screen. To display the guidance, you
need to make HDMI connection between the unit and
TV. Select the item with the cursor buttons of the remote
controller and press ENTER to confirm your selection. To
return to the previous screen, press RETURN.
1.
Start "Wi-Fi Setup".
1
Press RCV on the remote controller and then press
HOME.
2
Select "Setup" with the cursor buttons and press
ENTER.
3
Select "12. Network Setup" with the cursor buttons and
press ENTER.
• "12. Network Setup" becomes selectable after the
network starts up even if it cannot be selected first. It
may take about a minute to start up.
4
Select "Wi-Fi" with the cursor buttons and select "On" to
display "Wi-Fi Setup".
5
Select "Start" in "Wi-Fi Setup" with the cursor buttons
and press ENTER.
2.
Select the SSID of the access point to be connected
with the cursor buttons and press ENTER.
When the SSID of the access point appears on the TV
screen, select the desired access point.
• If you changed the initial setting of the access point to
skip password entry, step 4 starts automatically.
• If you changed the initial setting of the access point
to hide the SSID, see "When the access point is not
displayed".
3.
Select and set the authentication method.
Wi-Fi Setup
Please select the authentic
method.
Enter Password
Push Button
PIN code
When the screen above is displayed, select and set one of
the three authentication methods: "Enter Password", "Push
Button" and "PIN code". See below for details of and how to
set each method.
Enter Password: Enter the password of the access point
to establish connection.
1
Select "Enter Password" with the cursor buttons and
press ENTER.
2
Enter the password (
) on the keyboard screen, select
"OK" with the cursor buttons and press ENTER.
• In some case, the key board screen is displayed
automatically instead of authentication screen
depending on access point device.
To switch uppercase/lowercase, select "Shift" and press ENTER.
Select "Left" or "Right" and press ENTER to move the cursor to
the selected direction. Select "BS" and press ENTER to delete
the character at the left of the cursor position. To select whether to
mask the password with "*" or display it in plain text, press D on the
remote control. Press + 10 on the remote controller to enable the
"Shift" function and CLR to delete all the input characters.
3
If the security method of the access point to be
connected is WEP, select "Default Key ID", select "OK"
and press ENTER.
Push Button: Use the automatic setting button of the
access point to establish connection.
1
Select "Push Button" with the cursor buttons and press
ENTER.
2
Hold down the automatic setting button of the access
point for the necessary seconds, select "OK" with the
cursor buttons and press ENTER.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Onkyo-TX-NR535

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Onkyo TX-NR535 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Onkyo TX-NR535 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Onkyo TX-NR535

Onkyo TX-NR535 Gebruiksaanwijzing - Nederlands, Deutsch - 92 pagina's

Onkyo TX-NR535 Gebruiksaanwijzing - English - 76 pagina's

Onkyo TX-NR535 Gebruiksaanwijzing - Français - 40 pagina's

Onkyo TX-NR535 Gebruiksaanwijzing - Italiano - 92 pagina's

Onkyo TX-NR535 Gebruiksaanwijzing - Espanõl - 40 pagina's

Onkyo TX-NR535 Gebruiksaanwijzing - Svenska, Suomi - 92 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info