553767
113
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
113
En
Troubleshooting
Case1:
If “No Update” is displayed on the front display of the AV
receiver, the firmware has already been updated. You do
not need to do anything further.
Case2:
If an error occurs, “Error!! *-** No media” is displayed
on the front display of the AV receiver. (Alpha-numeric
characters on the front display are denoted by asterisks.)
See the following table and take appropriate action.
Errors during update via Network
Case3:
If you do not have a wired connection to the network,
please contact Onkyo Support ( 114).
Case4:
If an error occurs during updating process, disconnect then
reconnect the AC power cord and try again.
Case5:
If an error has occurred due to wrong selection of input
sources, turn off and on the AV receiver. Then retry the
update.
The AV receiver allows you to update firmware using a
USB storage device.
*
In this procedure, on-screen display may vary depending on
the model.
Note
Never unplug or turn off the AV receiver during updating pro-
cess.
Never plug or unplug an HDMI cable and a USB device during
updating process.
Never unplug the USB mass storage device and the power cord
during updating process.
It will take about 60 minutes to update the firmware.
The AV receiver will retain all your settings after update is fin-
ished.
Before you start
•CheckHDMI Control(RIHD)” setting ( 65). The
update may not be successful if this setting is on.
Turn off the controller device connected via RS232C and
via Ethernet network.
Turn off Powered Zone 2 and Powered Zone 3.
Stop playback of content from Internet Radio, iPod,
USB or Servers, etc.
How to turn off RIHD
Update procedure
Error Code Description
*
-10,
*
-20
Ethernet cable is not detected. Connect the
cable properly.
*
-11,
*
-13,
*
-21,
*
-28
Internet connection error.
Check the following items:
Make sure IP address, subnet mask, gateway
address, and DNS server are configured prop-
erly.
Make sure the router is turned on.
Make sure the AV receiver and the router are
connected with Ethernet cable.
Make sure the setup configuration of the
router is set properly. See the instruction
manual of the router.
If your network allows only one client con-
nection and there is any other device already
connected, the AV receiver cannot access the
network. Consult your Internet Service Pro-
vider (ISP).
If your modem does not function as a router,
you will need a router. Depending on your
network, you may need to configure the
proxy server if needed. See the document
provided by your ISP. If you still cannot
access the Internet, DNS or proxy server may
be temporarily down. Contact your ISP.
Others Retry the update procedure from the begin-
ning. If the error persists, please contact
Onkyo Support ( 114) and provide the error
code.
Updating the Firmware via USB
1
In the Main menu select “Hardware Setup”.
2
Select “HDMI”.
3
Set “HDMI Control(RIHD)” to “Off”.
1
Connect a USB storage device to your PC. If
there is any data in the USB storage, remove it.
2
Download the firmware file from the Onkyo
web site. The file name is as follows:
ONKAVR0001_*******.zip
Unzip the downloaded file. The following three
files are created:
ONKAVR0001_*******.of1
ONKAVR0001_*******.of2
ONKAVR0001_*******.of3
3
Copy the extracted files to the USB storage
device. Be careful not to copy the zip file.
4
Remove the USB storage device from your PC
and connect it to the USB port on the AV
receiver.
When the AV receiver has two USB ports, you can
use either one.
5
Make sure the AV receiver and TV are turned
on.
If the AV receiver is in standby mode, press ON/
STANDBY on the AV receiver to light up the
front display.
113

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Onkyo TX-NR3008 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Onkyo TX-NR3008 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Onkyo TX-NR3008

Onkyo TX-NR3008 Gebruiksaanwijzing - Nederlands - 228 pagina's

Onkyo TX-NR3008 Gebruiksaanwijzing - Deutsch - 228 pagina's

Onkyo TX-NR3008 Gebruiksaanwijzing - Français - 232 pagina's

Onkyo TX-NR3008 Gebruiksaanwijzing - Italiano - 228 pagina's

Onkyo TX-NR3008 Gebruiksaanwijzing - Espanõl - 232 pagina's

Onkyo TX-NR3008 Gebruiksaanwijzing - Svenska - 228 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info