553762
76
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
76
En
To use the same volume level as when the AV receiver was
last turned off, select “Last”.
The “Zone2 Power On Volume” and “Zone3 Power On
Vol ume ” cannot be set higher than the “Zone2 Maximum
Vol ume ” and “Zone3 Maximum Volume” setting.
This section explains how to turn Zone 2/3 on and off,
how to select an input source for Zone 2/3, and how to
adjust the volume for Zone 2/3.
Controlling Zone 2/3 from the AV receiver
Note
When Zone 2/3 is turned off, the output from the ZONE 2/3
12V TRIGGER OUT goes low (0 volts).
Controlling Zone 2/3 with the Remote
Controller
Note
To control Zone 2/3, you must press the remote controller’s
ZONE first.
ZONE turns red while Zone 2 is on, and green while Zone 3 is
on.
Note
Only analog input sources are output by the ZONE 2/3 PRE
OUT and FRONT WIDE/ZONE 2 L/R, FRONT HIGH/ZONE
3 L/R terminals. Digital input sources are not output. If no sound
is heard when an input source is selected, check if it’s connected
to an analog input.
You cannot select different AM or FM radio stations for your
main room and Zone 2/3. The same AM/FM radio station will be
heard in each room. For example, if you have an FM station for
the main room, that station will also be used in Zone 2.
When you connect ZONE3 speakers directly to the AV receiver,
Dolby Pro Logic IIz Height listening mode that require front
high speakers is unavailable.
When the input selector of Zone 2/3 is selected, power consump-
tion on standby mode slightly increases.
While Zone 2/3 is on, u functions will not work.
Using Zone 2/3
1
To turn on Zone 2/3 and select an input source,
press ZONE 2 or ZONE 3 followed by an input
selector button within 8 seconds.
Zone 2/3 turns on, the ZONE 2/3 indicator lights.
Tip
ZONE 2/3 12V TRIGGER OUT goes high (+12 V).
To select AM or FM, press TUNER input selector
and ZONE 2 or ZONE 3 repeatedly.
(North American models) You can also select SIR-
IUS.
To select the same source as that of the main room,
press ZONE 2 or ZONE 3 twice. “Zone 2 Selector:
Source” or “Zone 3 Selector: Source” appears on
the display.
2
To turn off Zone 2/3, press ZONE 2 or ZONE 3.
ZONE 2 or ZONE 3 indicator flashes.
Press OFF.
The zone is turned off, and the ZONE 2 or ZONE 3
indicator goes off.
ZONE 3
ZONE 2
OFF
ZONE 2 indicator
ZONE 3 indicator
Input selector buttons
1
Press ZONE repeatedly, then point the remote
controller at the AV receiver and press ON.
Tip
•The ZONE 2/3 12V TRIGGER OUT goes high (+12 V).
2
To select an input source for Zone 2/3, press
ZONE repeatedly, followed by INPUT SELEC-
TOR.
To select AM or FM, press TUNER input selector
and ZONE repeatedly.
(North American models) You can also select SIR-
IUS.
3
To turn off Zone 2/3, press ZONE repeatedly, fol-
lowed by STANDBY.
INPUT
SELECTOR
ON
ZONE
STANDBY
76

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Onkyo TX-NR1008 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Onkyo TX-NR1008 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Onkyo TX-NR1008

Onkyo TX-NR1008 Gebruiksaanwijzing - Nederlands - 204 pagina's

Onkyo TX-NR1008 Gebruiksaanwijzing - Deutsch - 204 pagina's

Onkyo TX-NR1008 Gebruiksaanwijzing - Français - 208 pagina's

Onkyo TX-NR1008 Gebruiksaanwijzing - Italiano - 204 pagina's

Onkyo TX-NR1008 Gebruiksaanwijzing - Espanõl - 208 pagina's

Onkyo TX-NR1008 Gebruiksaanwijzing - Svenska - 204 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info