455823
43
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
43
First Time Setup—Continued
Note:
When the automatic speaker setup is complete, the
Equalizer Settings (page 81) will be set to “Audyssey.
Error Messages
While the automatic speaker setup is in progress, one of
the following error messages may appear:
Ambient noise is too high
This message appears if there’s too much background
noise and the measurements cannot be performed prop-
erly. Remove the source of the noise and try again.
Speaker Detect Errors
This message appears if one of the speaker-related errors
below occurs.
One of the front speakers has not been detected.
One of the surround speakers has not been detected.
The surround back speakers have been detected but
the surround speakers haven’t.
The right surround back speaker has been detected but
the left surround back speaker hasn’t.
The number of speakers detected on the second or
third measurement was different to the number
detected on the first measurement.
Write Error
This message appears if saving fails.
Matching Error
This message appears if a speaker that was detected
during the 1st measurement is not detected during the
2nd or 3rd measurements. If this message appears, check
your speaker connections, and then try again.
Changing the Speaker Settings Manually
If you wish to make changes to the settings found during
the automatic speaker setup, follow the directions on
pages 77–81.
3
Press [ENTER].
The automatic speaker setup starts.
You can cancel the automatic speaker setup at
any point in this procedure simply by discon-
necting the setup microphone.
A test tone is output by each speaker in turn, as
the Audyssey 2EQ function determines which
speakers are connected. This takes a few min-
utes.
Note:
Quiet the room as much as possible. Back-
ground noise can disrupt the room measure-
ments. Close windows, silence cell phones,
televisions, radios, air conditioners, fluores-
cent lights, home appliances, light dimmers,
or other devices, and refrain from talking.
4
When the following display appears,
move the speaker setup microphone to
measurement point
2 (page 42), and
then press [ENTER].
Audyssey 2EQ performs more measurements.
This takes a few minutes.
5
When the following display appears,
move the speaker setup microphone to
measurement point
3 (page 42), and
then press [ENTER].
Audyssey 2EQ performs more measurements.
This takes a few minutes.
When the measurements are complete, the
results are calculated and saved automatically.
6
When the automatic speaker setup is
complete, disconnect the speaker setup
microphone.
To Retry the Automatic Speaker Setup
Press the [ENTER] button.
Make sure speakers that cannot be
detected are connected properly.
43

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Onkyo HT-S5100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Onkyo HT-S5100 in de taal/talen: Engels als bijlage per email.

De handleiding is 12,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info