Handleiding Onkyo C-7000R (pagina 2 van 36) (Engels)

462132

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

Compact Disc Player

C-7000R

Instruction Manual

Introduction

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete

outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand,

tripod, bracket, or table

specified by the manufacturer,

or sold with the apparatus.

When a cart is used, use

caution when moving the

cart/apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

15. Damage Requiring Service

Unplug the apparatus from the wall outlet and refer

servicing to qualified service personnel under the

following conditions:

A. When the power-supply cord or plug is damaged,

B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or water,

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician to

restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry

Never push objects of any kind into the apparatus

through openings as they may touch dangerous

voltage points or short-out parts that could result in a

fire or electric shock.

The apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as

vases shall be placed on the apparatus.

Don’t put candles or other burning objects on top of

this unit.

17. Batteries

Always consider the environmental issues and follow

local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation,

such as a bookcase or rack, ensure that there is

adequate ventilation.

Leave 20 cm (8") of free space at the top and sides and

10 cm (4") at the rear. The rear edge of the shelf or

board above the apparatus shall be set 10 cm (4")

away from the rear panel or wall, creating a flue-like

gap for warm air to escape.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS TO

RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

NE PAS

OUVRIR

AVIS

PORTABLE CART WARNING

S3125A

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal without

the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not user-

serviceable. If you cannot turn on the unit, contact

your Onkyo dealer.

3. Care—Occasionally you should dust the unit all over

with a soft cloth. For stubborn stains, use a soft cloth

dampened with a weak solution of mild detergent and

water. Dry the unit immediately afterwards with a

clean cloth. Don’t use abrasive cloths, thinners,

alcohol, or other chemical solvents, because they may

damage the finish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SECTION

CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the

voltage requirements printed on the unit’s rear panel

(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug is

readily operable (easily accessible) at all times.

Some models have a voltage selector switch for

compatibility with power systems around the world.

Before you plug in such a model, make sure that the

voltage selector is set to the correct voltage for your

area.

Pressing the [POWER] button to select OFF mode

does not fully disconnect from the mains. If you do

not intend to use the unit for an extended period,

remove the power cord from the AC outlet.

5. Preventing Hearing Loss

Caution

Excessive sound pressure from earphones and

headphones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

Batteries (battery pack or batteries installed) shall not

be exposed to excessive heat as sunshine, fire or the

like.

7. Never Touch this Unit with Wet Hands—Never

handle this unit or its power cord while your hands are

wet or damp. If water or any other liquid gets inside

this unit, have it checked by your Onkyo dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally

bought it.

• Do not leave rubber or plastic items on this unit for

a long time, because they may leave marks on the

case.

• This unit’s top and rear panels may get warm after

prolonged use. This is normal.

• If you do not use this unit for a long time, it may not

work properly the next time you turn it on, so be

sure to use it occasionally.

• When you’ve finished using this unit, remove all

discs and turn off the power.

9. Installing this Unit

• Install this unit in a well-ventilated location.

• Ensure that there’s adequate ventilation all around

this unit, especially if it’s installed in an audio rack.

If the ventilation is inadequate, the unit may

overheat, leading to malfunction.

• Do not expose this unit to direct sunlight or heat

sources, because its internal temperature may rise,

shortening the life of the optical pickup.

• Avoid damp and dusty places, and places subject to

vibrations from loudspeakers. Never put the unit on

top of, or directly above a loudspeaker.

• Install this unit horizontally. Never use it on its side

or on a sloping surface, because it may cause a

malfunction.

• If you install this unit near a TV, radio, or VCR, the

picture and sound quality may be affected. If this

occurs, move this unit away from the TV, radio, or

VCR.

10. Moisture Condensation

Moisture condensation may damage this unit.

Read the following carefully:

Moisture may condense on the lens of the optical

pickup, one of the most important parts inside this

unit.

• Moisture condensation can occur in the following

situations:

– The unit is moved from a cold place to a warm

place.

– A heater is turned on, or cold air from an air

conditioner is hitting the unit.

– In the summer, when this unit is moved from an

air conditioned room to a hot and humid place.

– The unit is used in a humid place.

• Do not use this unit when there’s the possibility of

moisture condensation occurring. Doing so may

damage your discs and certain parts inside this unit.

If condensation does occur, unplug the power cord

and leave the unit for two to three hours in the room

temperature.

This unit contains a semiconductor laser system and is

classified as a “CLASS 1 LASER PRODUCT”. So, to use

this model properly, read this Instruction Manual

carefully. In case of any trouble, please contact the store

where you purchased the unit.

To prevent being exposed to the laser beam, do not try to

open the enclosure.

CAUTION:

CLASS 1M VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN. DO NOT VIEW

DIRECTLY WITH OPTICAL INSTRUMENTS.

THIS PRODUCT UTILIZES A LASER. USE OF

CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

The label on the right is applied

on the rear panel.

1. This unit is a CLASS 1 LASER PRODUCT and

employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not

remove the cover. Refer servicing to qualified

personnel.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved

by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

For Canadian Models

NOTE:

THIS CLASS B DIGITAL APPARATUS COMPLIES

WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

REMARQUE:

CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST

CONFORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRESPONDANTE DE

LA PRISE ET POUSSER JUSQU’AU FOND.

For British models

Replacement and mounting of an AC plug on the power

supply cord of this unit should be performed only by

qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance

with the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured

black.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or coloured

red.

IMPORTANT

The plug is fitted with an appropriate fuse. If the fuse

needs to be replaced, the replacement fuse must approved

by ASTA or BSI to BS1362 and have the same ampere

rating as that indicated on the plug. Check for the ASTA

mark or the BSI mark on the body of the fuse.

If the power cord’s plug is not suitable for your socket

outlets, cut it off and fit a suitable plug. Fit a suitable fuse

in the plug.

For European Models

Declaration of Conformity

We,

ONKYO EUROPE

ELECTRONICS GmbH

LIEGNITZERSTRASSE 6,

82194 GROEBENZELL,

GERMANY

GROEBENZELL, GERMANY

ONKYO EUROPE ELECTRONICS GmbH

K. MIYAGI

declare in own responsibility, that the ONKYO product

described in this instruction manual is in compliance with the

corresponding technical standards such as EN60065,

EN55013, EN55020 and EN61000-3-2, -3-3.

Features

• Plays Audio CD, CD-R, CD-RW, MP3 CD,

and WMA CD

• DIDRC (Dynamic Intermodulation Distortion

Reduction Circuitry)

• Separate Digital/Analog Circuitry

• Separate Massive Transformers for Digital

and Analog Circuitry (Toroidal Transformer

for Analog Circuitry)

• Thermally Regulated High-Precision Clock

• Silent Disc Mechanism with Solid Die-Cast

Aluminum Tray

• Separate Anti-Vibration Aluminum Panels for

Top, Front, and Sides

• Side-mounted Circuit Board Construction to

Reduce Vibration

• PLL Ultra Low Jitter Technology

• Separate TI (Burr-Brown) 192 kHz/24-Bit

DACs (PCM1792) for L/R Channels

• Pure Analog Mode

• Transport Mode for Digital Output

• AES/EBU Balanced Digital Output with XLR

Connector

• 3 Digital Outputs (Optical, Coaxial and

AES/EBU)

• Gold-Plated, Machined Solid Brass, Wide

Pitch Audio Outputs

• Display Dimmer (Normal/Dim/Off)

Discs should be properly finalized.

Technologies

DIDRC (Dynamic Intermodulation

Distortion Reduction Circuitry)

Since the advent of digital audio, the values of

S/N (signal-to-noise) ratio have risen

significantly. However, it is also recognized that

in terms of perceived S/N, analog audio sources

are not inferior to digital sources.

Generally, S/N measures the ratio when sound

is and not produced, but takes no account of the

noise generated during sound reproduction.

For a long time, Onkyo has focused and made

extensive research on the S/N when sound is

produced (dynamic S/N). Using a mechanism

that captures the noise beyond audible range, it

has been possible to determine that both

dynamic S/N and perceived S/N aggravate

during music reproduction.

Although frequencies above 20 kHz are beyond

human hearing, it is well known that a beat can

be perceived if different signals are overlapped

at such frequencies.

During the analog audio era, no significant

signals were entering beyond the audible range.

However, the digital era has made recording

beyond the audible range possible and the

generated beat is now perceivable.

With Onkyo’s DIDRC technology, a new

approach is introduced which prevents such

beat from penetrating the audible range.

Separate Digital/Analog Circuitry and

Transformers

To prevent unwanted interference, the C-7000R

employs physically separate circuitry for digital

and analog processing. In the same vein, the

player also features separate transformers for

digital and analog circuitry.

Thermally Regulated Super-Precision Clock

The C-7000R boasts an extremely precise

clocking mechanism that controls and

coordinates the timing of all digital signal

processes—rather like how a conductor directs

and coordinates the individual instruments of

an orchestra. The C-7000R uses a state-of-the-

art crystal oscillator that achieves a frequency

deviation of ±1.5 ppm at room temperature-

much lower than with a conventional oscillator.

Even in surrounding temperatures of -30°C or

+80°C the frequency remains stable, with only

±0.5 ppm of additional frequency deviation.

PLL (Phase Locked Loop) Ultra-Low Jitter

Technology

Jitter is an unwanted side-effect of the digital-

to-analog conversion process caused by

fluctuations in the time domain of a digital

signal. PLL ultra-low jitter technology reduces

jitter by comparing the input and output phases

of the digital signal and creating an accurate

clock waveform. This enhances the precision of

digital signal processing and noticeably

improves perceived audio quality.

Side-mounted Circuit Board Construction

Rather than being directly connected to the

chassis base, the circuit boards inside the

C-7000R are cushioned by internal struts and

affixed to the front, side, and rear panels. This

method of construction prevents vibrations

from the chassis from adversely affecting the

circuit boards.

Block Diagram

DIDRC

(Dynamic Intermodulation Distortion Reduction Circuitry)

Supplied Accessories

Make sure you have the following accessories:

Remote controller (RC-796C). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1)

Batteries (R03/AAA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (2)

Power cord (1.8 m/5.9 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1)

(Plug type varies from country to country.)

Audio connection cable (0.8 m/2.6 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1)

In catalogs and on packaging, the letter at the end of the product name indicates the color.

Specifications and operations are the same regardless of color.

Remote controller and two batteries

Power cord

Audio connection cable

Thank you for purchasing an Onkyo Compact Disc Player. Please read this

manual thoroughly before making connections and plugging in the unit.

Following the instructions in this manual will enable you to obtain optimum

performance and listening enjoyment from your new Compact Disc Player.

Please retain this manual for future reference.

Contents

Introduction

Important Safety Instructions .................................................................................2

Precautions...............................................................................................................3

Features ....................................................................................................................5

Technologies ............................................................................................................6

Block Diagram ..........................................................................................................7

Supplied Accessories ..............................................................................................8

Before Using the Compact Disc Player................................................................10

Installing the Batteries .......................................................................................10

Using the Remote Controller .............................................................................10

Installing the Compact Disc Player ....................................................................10

Getting to Know the Compact Disc Player ..........................................................11

Front Panel ........................................................................................................11

Display ...............................................................................................................12

Rear Panel.........................................................................................................13

Remote Controller..............................................................................................14

Disc Note ...........................................................................................................15

Connections

Connections ...........................................................................................................17

Cable and Jacks ................................................................................................17

Connecting the Power Cord...............................................................................18

Connecting a Preamplifier or Integrated Amplifier .............................................19

Turning On & Basic Operations

Basic Operations....................................................................................................21

Turning On/Off the Compact Disc Player ..........................................................21

Playing the Disc .................................................................................................22

Selecting Files (MP3/WMA)...............................................................................23

Setting the Display Brightness ...........................................................................24

Advanced Operations

Advanced Operations ............................................................................................25

Repeat Playback................................................................................................25

Memory Playback (CD)......................................................................................26

Memory Playback (MP3/WMA)..........................................................................27

Random Playback..............................................................................................29

Selecting a Folder (Search Mode) .....................................................................29

Displaying Disc Information ...............................................................................30

Custom Setup

Custom Setup.........................................................................................................31

Setup Procedures ..............................................................................................31

Preferences .......................................................................................................31

Setting the Analog/Digital Output.......................................................................32

Others

Troubleshooting .....................................................................................................33

Specifications.........................................................................................................35

Before Using the Compact Disc Player

Note

• If the remote controller doesn’t work reliably, try replacing the

batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time,

remove the batteries to prevent damage from leakage or

corrosion.

• Remove expired batteries as soon as possible to prevent damage

from leakage or corrosion.

To use the remote controller, point it at the compact disc

player’s remote control sensor, as shown below.

Note

• The remote controller may not work reliably if the compact disc

player is subjected to bright light, such as direct sunlight or

inverter-type fluorescent lights. Keep this in mind when

installing.

• If another remote controller of the same type is used in the same

room, or the compact disc player is installed close to equipment

that uses infrared rays, the remote controller may not work

reliably.

• Don’t put anything, such as a book, on the remote controller,

because the buttons may be pressed inadvertently, thereby

draining the batteries.

• The remote controller may not work reliably if the compact disc

player is installed in a rack behind colored glass doors. Keep this

in mind when installing.

• The remote controller will not work if there’s an obstacle

between it and the compact disc player’s remote control sensor.

Install the compact disc player on a sturdy rack or shelf.

Position it so that its weight is evenly dispersed on its four

legs. Do not install the compact disc player in a place with

vibration or an unstable location.

Installing the Batteries

To open the battery compartment, press the small

hollow and slide the cover.

Insert the two supplied batteries (R03/AAA) in

accordance with the polarity diagram inside the

battery compartment.

Replace the cover and slide it shut.

Using the Remote Controller

Remote control sensor

Compact disc player

Approx. 16 ft. (5 m)

30° off center

(Left/Right)

Installing the Compact Disc Player

10 cm (4")

20 cm (8")

10 cm (4")

Getting to Know the Compact Disc Player

The page numbers in parentheses show where you can find the main explanation for each item.

a ON/STANDBY button (➔ 21)

Use this button to set the compact disc player to On or

Standby.

b Standby LED (➔ 21)

Lights when the compact disc player is in Standby

mode.

c Remote control sensor (➔ 10)

The sensor receives control signals from the remote

controller.

d Display (➔ 12)

See “Display”.

e Disc tray (➔ 22)

Insert discs into this tray.

f 0 button (➔ 22)

Opens and closes the disc tray.

g 3 button (➔ 22)

Use this button to pause disc playback. When paused,

this resumes playback.

h 2 button (➔ 22)

Use this button to stop disc playback.

i 1 button (➔ 22)

Use this button to play the disc.

j OUTPUT MODE button (➔ 32)

Use this button to switch the audio output signal

between analog and digital (or both).

k POWER switch (➔ 21)

This is the main power switch. When set to the OFF

position (@), the compact disc player is completely

shutdown. It must be set to the ON position (^) to set

the compact disc player to On or Standby.

l Display Off LED (➔ 24)

Lights when the display is turned off.

Before entering standby mode with the ASb function,

the Display Off LED flashes 30 seconds before the

ASb function starts running.

m 7 button (➔ 22)

Use this button to skip to the beginning of the track

being played. Press and hold down to fast reverse.

n 6 button (➔ 22)

Use this button to skip to the beginning of the next

track. Press and hold down to fast forward.

Front Panel

d eb

c gf

m n

For detailed information, see the pages in parentheses.

a 1 indicator (➔ 22)

Lights during playback.

b 3 indicator (➔ 22)

Lights when playback is paused.

c MEMORY indicator (➔ 26, 27, 28)

Lights during memory playback.

d FOLDER indicator (➔ 23)

Lights together with the folder name.

e TRACK indicator (➔ 22)

Lights together with the track number or file name.

f TOTAL indicator (➔ 21)

Lights when the total and remaining time of the track

are shown.

g REMAIN indicator (➔ 30)

Lights when the remaining time of the track is shown.

h RANDOM indicator (➔ 29)

Lights during random playback.

i ~ 1 indicator (➔ 25)

Lights during repeat playback. “1” is shown when

only the currently playing track is repeated.

j Audio output indicators

Indicate the type of audio output (➔ 32): DIGITAL

and/or ANALOG.

k MP3 indicator (➔ 21)

Lights together with the folder name, file number or

file name which contains MP3 tracks.

l WMA indicator (➔ 21)

Lights together with the folder name, file number or

file name which contains WMA tracks.

m Message area

Displays various information.

Display

bcd e gja

kl m

ihf

a AUDIO OUTPUT ANALOG L/R jacks

Connect the analog audio in jack of an amplifier or

similar to this jack, using the supplied audio cable.

b AUDIO OUTPUT DIGITAL AES/EBU jack

This balanced AES/EBU output is for connecting a

component with a balanced AES/EBU input.

c AUDIO OUTPUT DIGITAL COAXIAL jack

This coaxial digital audio output is for connecting

components with coaxial digital audio inputs, such as

preamplifier.

d AUDIO OUTPUT DIGITAL OPTICAL jack

This optical digital audio output is for connecting

components with optical digital audio inputs, such as

preamplifier.

e AC INLET

The supplied power cord is connected here. The other

end of the power cord should be connected to a

suitable wall outlet.

Rear Panel

See “Connections” for connection information

(➔ 17 to 19).

Remote Controller

You can also use the remote controller to control your Onkyo C-7000R.

For detailed information, see the pages in parentheses.

a 8 button (➔ 21)

Sets the compact disc player to On or Standby.

b DIMMER button (➔ 24)

Adjusts the display brightness.

c DISPLAY button (➔ 30)

Displays information about the current input source.

d RANDOM button (➔ 29)

Used with the random playback.

e Playback mode buttons (➔ 22)

3 button

Used to pause playback. When paused, this resumes

playback.

7 button

Used to skip to the beginning of the track being

played.

1 button

Used to play the disc.

6 button

Used to skip to the beginning of the next track.

5 button

Used to fast reverse the current song.

2 button

Used to stop disc playback.

4 button

Used to fast forward the current song.

f !/"/#/$ and ENTER buttons

Used to select and adjust settings.

g SEARCH button (➔ 29)

Search for a folder on a disc containing MP3 or WMA

tracks.

h SETUP button

Used to change settings.

i Number buttons (➔ 24)

Used to select tracks and the like.

j 0 button (➔ 22)

Open and close the disc tray.

k OUTPUT MODE button (➔ 32)

Use this button to switch the audio output signal

between analog and digital (or both).

l REPEAT button (➔ 25)

Used with the repeat playback.

m MEMORY button (➔ 26, 27, 28)

Used to begin or end memory playback.

n CLEAR button

Used to clear any numbers that have been entered

during numeric input. When making a memory

setting, the selected track is erased.

The compact disc player supports the following discs.

• Do not use discs designed for purposes other than audio,

such as CD-ROMs for PC use. Abnormal noise could

damage the speakers or compact disc player.

• The compact disc player supports CD-R and CD-RW

discs. Note that some discs may not playback because of

the CD characteristics, scratches, contamination or the

recording state. A CD recorded with an audio CD record

will not playback unless it is finalized.

• Never use discs which have a special shape (such as

hearts or octagons). These types of discs could jam and

damage the compact disc player.

Some audio CDs with copy-control function do not

comply with official CD standards. These are special discs

and cannot be played with this compact disc player.

Hold discs by the edge, or by the center hold and edge.

Avoid touching the playback surface (surface with nothing

printed on it).

Do not attach paper or stickers, or write on the playback or

label surface of the disc. Take care not to scratch or

damage the disc.

Do not use discs with residue from cellophane tape, rental

discs with labels which are peeling off, or discs with

decorative labels. This type of disc could get stuck in the

compact disc player, or could damage the compact disc

player.

Do not leave a CD-R/CD-RW having a label printed with

an inkjet printer in the compact disc player for a long time.

The disc could get stuck in the compact disc player, or

could damage the compact disc player.

Remove the disc from the compact disc player when not

being played, and store it in a case. A freshly printed disc

will stick easily, and should not be played immediately.

If the disc is dirty, the compact disc player will have a hard

time reading signals, and the audio quality may drop. If

the disc is dirty, gently wipe off fingerprints and dust with

a soft cloth. Lightly wipe from the center outwards.

To remove stubborn dust or dirt, wipe the

disc with a soft cloth dampened with

water, and then dry it with a dry cloth. Do

not use cleaning spray for analog records

or antistatic agents, etc.

Never use volatile chemicals such as benzine or paint

thinner as they can impregnate the disc surface.

Moving the compact disc player from a cold room into a

warm room, or heating a cold room with a heater may

cause waterdrops to form inside the compact disc player.

This is called condensation. Not only does this cause

malfunction, but it can also damage the compact disc

player or any inserted disc. Remove discs from the

compact disc player when not in use.

If condensation appears, unplug the power cord and leave

the compact disc player more than 3 hours at room

temperature.

Disc Note

Supported Discs

Audio CD PCM

CD-R Audio CD, MP3,

WMA

CD-RW Audio CD, MP3,

WMA

CD playback with copy-control function

Handling Discs

Precautions for Rental Discs

Label surface

(printed surface)

Playback

surface

Precautions for Inkjet Printable Discs

Caring for Discs

About the Condensation

MP3 and WMA files recorded on a CD-R/CD-RW can be

played with this compact disc player.

• Use discs which have been recorded following the

ISO9660 Level 2 file system. (The supported directory

depth is eight levels, the same as ISO9660 Level 1)

Discs recorded with the hierarchical file system (HFS)

cannot be played.

• Always close the disc tray.

Note

• A disc recorded with a recorder or personal computer may not

play in some cases. (Cause: Disc’s characteristics, damaged or

dirty disc, dirt on player’s lens, dew condensation, etc.)

• A disc recorded on a personal computer may not play because of

the application settings or environment. Record the disc with the

proper format. (Contact the application maker for details.)

• A disc with insufficient storage capacity may not play back

properly.

• Only MP3 files with the extension “.MP3” or “. mp3”

are supported.

• This compact disc player supports files recorded in

MPEG 1 Audio Layer 3 (32-320 kbps), with the

sampling frequency of 32/44.1/48 kHz.

• Variable bitrates (VBR) between 32 kbps and 320 kbps

are supported. The time information during VBR

playback may not display correctly.

• WMA stands for “Windows Media

Audio”, an audio

compression technology developed by Microsoft

Corporation USA.

• Only WMA files with the extension “.WMA” or “.wma”

are supported.

• Encode the WMA file with an application approved by

Microsoft Corporation USA. The file may not playback

correct if encoded with an unapproved application.

• Variable bitrates (VBR) between 32 kbps and 192 kbps

(32/44.1/48 kHz) are supported.

• Copyright-protected WMA files cannot be played back.

• WMA Pro, Lossless and Voice are not supported.

Windows Media is a registered trademark or trademark of

Microsoft Corporation in the United States and/or in other

countries.

Playback of MP3 and WMA CDs

Playback of MP3 CDs

Playback of WMA CDs

Connections

Note

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio cables away from power cords and speaker cables.

• The compact disc player’s optical digital jack has a shutter-type cover that opens when an optical plug is inserted and closes when it’s removed. Push plugs in all the way.

• To prevent shutter damage, hold the optical plug straight when inserting and removing.

• The analog audio cable can be used instead of the coaxial cable.

Plugging the AES/EBU cable

Match the pins and insert the jack until you hear a “click.” Make sure that the jack is locked

by lightly pulling the connection cable.

Unplugging the AES/EBU cable

Pull out the connection cable while holding down the button.

Cable and Jacks

Balanced AES/EBU This is a professional digital audio interface. Balanced AES/EBU cables are used for better noise immunity and longer cable runs. The maximum

sampling rate for PCM output is 44.1 kHz/16 bit, 2ch.

Optical digital audio Optical digital connections allow you to enjoy digital sound. The maximum sampling rate for PCM input is 44.1 kHz/16 bit, 2ch.

Coaxial digital audio Coaxial digital connections allow you to enjoy digital sound. The maximum sampling rate for PCM input is 44.1 kHz/16 bit, 2ch.

Analog audio (RCA) Analog audio connections (RCA) carry analog audio.

About Balanced Output (AES/EBU Jack)

OPTICAL

Orange

White

Red

Right!

Wrong!

Push

Tip

• To reduce noise, do not tie the signal cable and power cable

together. Wire them so that they are away from each other.

Note

• Never disconnect the power cord from the compact disc

player while the other end is still plugged into a wall outlet.

Doing so may cause an electric shock. Always disconnect the

power cord from the wall outlet first, and then the compact disc

player.

• Turning on the compact disc player may cause a momentary

power surge that might interfere with other electrical equipment

on the same circuit. If this is a problem, plug the compact disc

player into a different branch circuit.

• Do not use a power cord other than the one supplied with the

compact disc player. The supplied power cord is designed

exclusively for use with the compact disc player and should not

be used with any other equipment.

Connecting the Power Cord

AC INLET

Compact Disc Player C-7000R

Supplied power cord

To an AC wall outlet

(Plug type varies from

country to country.)

Make sure that the main power of the compact disc

player is turned off.

Connect all of your components.

Connect the supplied power cord to the compact

disc player’s AC INLET.

Plug the power cord into an AC wall outlet.

This is an example of analog connection using the preamplifier P-3000R.

This is an example of digital connection using the preamplifier P-3000R.

Connect either of them.

Connecting a Preamplifier or Integrated Amplifier

Analog Connection

Preamplifier P-3000R

Compact Disc Player C-7000R

Digital (Optical or Coaxial) Connection

Preamplifier P-3000R

Compact Disc Player C-7000R

Connect either of them.

Digital (AES/EBU) Connection

Preamplifier P-3000R

Compact Disc Player C-7000R

This is an example of AES/EBU connection using the preamplifier P-3000R.

Turning On & Basic O perations

Basic Operations

(Audio CD Display)

(MP3/WMA Display)

Tip

• After a certain period of warning up, the temperature of the

compact disc player’s components and internal temperature are

stabilized, and the sound will soften.

Note

• If the message “NO DISC” appears on the display, no disc

information is available.

• The compact disc player remembers the state when power was

previously turned OFF, and returns to the state.

Note

• See “Custom Setup” for the auto standby function (➔ 32).

Turning On/Off the Compact Disc Player

POWER

ON/STANDBY

Turning On the Compact Disc Player

Set POWER to the ON position (^) on the front

panel.

Press 8 to turn on the compact disc player.

The compact disc player comes on, the display lights,

and the Standby LED goes off.

You can also use compact disc player’s

ON/STANDBY.

Total number

of tracks

Total

playing time

Total number

of folders

Total number

of tracks

Turning Off the Compact Disc Player

Press 8 to set the compact disc player to Standby.

The compact disc player will enter Standby mode, and

the Standby LED lights.

You can also use compact disc player’s

ON/STANDBY.

To completely shut down the compact disc player,

set POWER to the OFF position (@).

(Audio CD Display)

(MP3/WMA Display)

File name will be displayed by scrolling.

Tip

• Only alphanumeric characters in MP3/WMA CD information

are displayed correctly. Double-byte characters and other

characters appear as underscores.

• If a disc has been set in the tray, when the power of the compact

disc player is turned on, then it starts to play automatically.

■ To Select Tracks

Press 6 to select the next track/file or 7 to select

the previous track/file.

• If you press 7 during playback or while

playback is paused, the beginning of the current

track/file is selected.

• If you select a track/file while playback is stopped,

press 1 to start playback.

• When 7/6 are pressed, the following Disc

information is displayed for MP3/WMA.

(During playback) File number/File name → File

name → File number/playing time

(Paused) File number/File name → File name →

Folder number/File number

■ To Fast-Forward or Fast-Reverse

During playback or while playback is paused, hold

down 4 to fast-forward or 5 to fast-reverse.

■ To Pause Playback

During playback, press 3. The 3 indicator lights.

To resume playback, press 1 or 3 again.

■ To Stop Playback

Press 2 to stop playback.

■ To Eject the Disc

Press 0 to open the disc tray.

Note

• For MP3/WMA CDs, you can select MP3/WMA files in other

folders.

Playing the Disc

Press 0 to open the disc tray.

Pressing 0 while the compact disc player is on

Standby will turn on the compact disc player and open

the disc tray.

Place the disc on the tray with the label-side facing

up.

When you want to listening to the 8 cm disc, place it

in the center of the tray.

Press 1 to start playback.

The disc tray closes and playback starts.

Track currently

playing

Elapsed track

time

1 indicator

3 indicator

For MP3/WMA CDs, files (MP3/WMA files) may be

organized in a hierarchically, with folders containing files

and subfolders, as shown below.

For the compact disc player, there are two modes for

selecting files (MP3/WMA files): Navigation mode and

All Folder mode.

In Navigation mode, you can select files (MP3/WMA

files) by navigating through the folder hierarchy, moving

in and out of folders and subfolders.

In All Folder mode, all folders appear at the same level,

making it easy to select folders regardless of the hierarchy.

Note

• If you don’t select a specific MP3/WMA file or folder for

playback, all of the MP3/WMA files on the disc will be played

in numerical order starting with file #1 in parentheses.

Selecting Files (MP3/WMA)

In this manual, MP3/WMA files are referred to as files.

Likewise, folders (directories) are referred to as folders.

File #11

File #1

File #10

Folder #3

File #12

Root

Folder #1

Folder #2

File #13

Folder #4

File #14

File #18

In Navigation mode, you can select files by navigating

through the folder hierarchy. This mode can only be used

while playback is stopped.

To cancel the procedure at any point, press 2 on the

remote controller.

Note

• The behavior of 2 on the compact disc player can be set from

“STOP KEY” (➔ 32).

Selecting Files in Navigation Mode

While playback is stopped, press " or 2.

The compact disc player enters Navigation mode and

“[ROOT]” appears on the display.

3, 7, 1, 6, 2

!, ", #, $

ENTER

Press " or ENTER (front panel: 1).

The first folder name in ROOT appears on the display.

If the disc contains no folders, the first file name

appears.

Use #/$ or 7/6 to select other folders and

files at the same level. To move up a level, press !

or 3 (front panel: 2).

Folders that don’t contain files or subfolders can’t be

selected.

Press ENTER or " to move down a level (front

panel: 1).

Use #/$ or 7/6 to select a file in the folder.

Press ENTER or 1.

Playback will start with the specified file or folder and

continue until all of the files on the disc have been

played.

In All Folder mode, you don’t have to navigate the folder

hierarchy because all folders that contain files appear at

the same level. This mode can only be used while

playback is stopped.

To cancel the procedure at any point, press 2.

■ To Select Folders and Files by Number

1. Use the number buttons as shown in the examples

below to enter folder/file numbers.

2. Playback starts. When you enter folder number,

playback will start from the first file in the selected

folder. If a folder contains more than 99 files, single-

and double-digit file numbers must be preceded by

zeros. For example, to specify file #8, press 8. To

specify file #34, press >10, 3, and 4. To specify file

#134, press >10, 1, 3, and 4.

Note

• The behavior of 2 on the compact disc player can be set from

“STOP KEY” (➔ 32).

Selecting Files in All Folder Mode

While playback is stopped, press ! or 3 (front

panel: press and hold 2).

The compact disc player enters All Folder mode, and

“1-” appears on the display.

Use #/$ or 7/6 to select the other folders.

You can select any folder that contains files.

3, 7, 1,

6, 2

!, ", #, $,

ENTER

Press " (front panel: 1).

The first file name inside the folder appears.

Use #/$ or 7/6 to select the files within the

folder.

To select another folder, press 3 again (front panel:

2), and then use 7/6 to select it.

Press ENTER or 1 to start playback.

Playback will start with the specified file or folder and

continue until all of the file on the disc have been

played.

To select: Press:

Folder/File #8

Used to enter numbers over 10.

Folder/File #10

Folder/File #34

You can adjust the brightness of the compact disc player’s

display.

Note

• The display lights for a 5 seconds if you control any buttons on

the front panel or remote controller when the display brightness

is set to OFF.

Setting the Display Brightness

Press DIMMER repeatedly to change the brightness

of the display in sequence.

Normal → Dim → Off

DIMMER

Normal

Dim

Off

The Display Off LED lights.

Advanced O perations

Advanced Operations

In repeat playback, you can play an entire disc repeatedly,

play one track repeatedly, or combine it with memory

playback to play the playlist repeatedly, or random

playback to play all of the tracks on the disc in random

order repeatedly.

Tip

• Repeat playback is cancelled when you press 0 to open the disc

tray.

• Repeat playback is cancelled when you press 8 or

ON/STANDBY to turn off the compact disc player.

Repeat Playback

REPEAT

Press REPEAT repeatedly to select Repeat All,

Repeat 1 or Repeat Off.

The “~” or “~ 1” indicator lights.

Repeat All → Repeat 1 → Repeat Off

Repeat-1 playback can’t be combined with memory

playback, random playback.

To cancel repeat playback, press REPEAT

repeatedly until the “RPT OFF” appears.

The “~” or “~ 1” indicator goes off.

~ indicator

Repeat All

~ 1 indicator

Repeat 1

Repeat Off

In memory playback, you can create a playlist of up to 25

tracks. Memory playback can be set only when the

playback is stopped.

■ To Change the Display

While the memory setting operations, press DISPLAY

repeatedly to change the display information as follows:

Track number/Playlist number → Track number/Playing

time → Track number/Total playing time

■ To Select Other Tracks During Memory

Playback

Use 7/6 to select other tracks during memory

playback.

■ To Check the Playlist

While playback is stopped, use 5/4 to scroll

through the playlist. Track number and play time are

displayed.

■ To Remove Tracks from the Playlist

• While memory playback is stopped, press CLEAR.

Each press removes the last track from the playlist.

• The playlist is deleted on changing the playback mode

(press MEMORY after stopping the playback).

■ To Cancel Memory Playback

• Stop the playback, then press MEMORY to change the

playback mode. The MEMORY indicator goes off, and

memory playback is cancelled.

• Memory playback is also cancelled by pressing 0 to

open the disc tray, 8 or ON/STANDBY to turn off the

compact disc player.

Note

• If the total playing time is more than 99 minutes and 59 seconds,

“--:--” appears.

• You can add up to 25 tracks to the playlist. If you try to add more,

the message “MEM-FULL” appears.

Memory Playback (CD)

DISPLAY

7, 1, 6,

5, 4

MEMORY

ENTER

CLEAR

Press MEMORY.

The MEMORY indicator lights.

Use 7/6 to select the first track you want to

add to the playlist, and then press 1 or ENTER.

Repeat this step to add additional tracks to the playlist.

You can alternatively use the number buttons to select

tracks.

Press ENTER or 1.

The memory playback starts.

MEMORY indicator

Playlist numberTrack number

Track currently playing

In memory playback, you can create a playlist of up to 25

files. Memory playback can be set only when the playback

is stopped.

■ To Change the Display

While the memory setting operations, press DISPLAY to

change the display information as follows:

File name → Folder name → Folder number/File number

Note

• See “Selecting Files (MP3/WMA)” for the Navigation Mode

information (➔ 23).

• The behavior of 2 on the compact disc player can be set from

“STOP KEY” (➔ 32).

• Memory playback is cancelled when you press 0 to open the

disc tray.

• Memory playback is cancelled when you press 8 or

ON/STANDBY to turn off the compact disc player.

Memory Playback (MP3/WMA)

Memory Playback in Navigation Mode

3, 7, 1,

6, 2

MEMORY

DISPLAY

!, ", #, $

ENTER

Press MEMORY.

The MEMORY indicator lights.

Press " or 2.

The compact disc player enters Navigation mode and

“[ROOT]” appears on the display.

Press " or ENTER (front panel: 1).

The first folder name in ROOT appears on the display.

Use #/$ or 7/6 to select other folders and

files at the same level.

Folders that don’t contain files or subfolders can’t be

selected.

Press ENTER or " to move down a level (front

panel: 1).

Use #/$ or 7/6 to select a file in the folder.

Press 1.

The first file is memorized in the playlist.

Use #/$ or 7/6 to continue selecting the

memory file.

To move up a level, press ! or 3 (front panel: 2).

To continue selecting the memory file, repeat steps 4

to 7.

To memorize other files of the same folder in the

playlist, use 7/6 to select files, then press 1.

Press ENTER or 1.

Memory playback starts.

Note

• See “Selecting Files (MP3/WMA)” for the All Folder Mode

information (➔ 24).

• The behavior of 2 on the compact disc player can be set from

“STOP KEY” (➔ 32).

• Memory playback is cancelled when you press 0 to open the

disc tray.

• Memory playback is cancelled when you press 8 or

ON/STANDBY to turn off the compact disc player.

Memory Playback in All Folder Mode

Press MEMORY.

The MEMORY indicator lights.

Press ! or 3 (front panel: press and hold 2).

The compact disc player enters All Folder mode and

“1-” appears on the display.

Use #/$ or 7/6 to select the folders.

3, 7, 1,

6, 2

MEMORY

!, ", #, $

ENTER

MEMORY indicator

Press " (front panel: 1).

Use #/$ or 7/6 to select the files.

Press 1 to memorized the first file.

Press 3 (front panel: 2), then repeat steps 3 to 6.

To memorize other files of the same folder in the

playlist, repeat steps 5 to 6.

Press ENTER (front panel: 1).

Memory playback starts.

In random playback, all of the files on the disc are played

in random order. This mode can only be used while

playback is stopped.

If you press RANDOM during playback, the message

“NOR PLY” (Normal play) is displayed.

Tip

• Random playback is cancelled when you press 0 to open the

disc tray.

• Random playback is cancelled when you press 8 or

ON/STANDBY to turn off the compact disc player.

Random Playback

While playback is stopped, press RANDOM.

The RANDOM indicator lights.

Press 1.

The random playback starts.

To cancel random playback, stop the playback,

then press RANDOM to change the playback mode.

The RANDOM indicator goes off, and random

playback is cancelled.

RANDOM

RANDOM indicator

This section explains how to select MP3/WMA folders

during Playback.

Note

• SEARCH cannot be used during Random Playback and

Memory Playback (➔ 26, 29).

• See “Selecting Files in All Folder Mode” to select folder by

number(➔ 24).

Selecting a Folder (Search Mode)

During playback, press SEARCH.

The compact disc player enters All Folder mode and

folders are displayed.

To select the previous folder, press 7. To select

the next folder, press 6.

You can also use the number buttons to select the

folder.

Press ENTER or 1.

Playback will start from the first file in the selected

folder.

ENTER

7, 6

(Audio CD Display)

Track and total playing time appears on the display.

(MP3/WMA Display)

The name of disc appears on the display.

(Audio CD Display)

Elapsed file time:

The length of time that the current file has been playing

(default display).

Remaining file time:

The amount of time remaining for the current file

(REMAIN indicator appears).

Remaining disc time:

The amount of time remaining for the entire disc

(TOTAL and REMAIN indicators appear).

(MP3/WMA Display)

You can display various information about the MP3/WMA

file currently playing, including ID3 tags such as title

name, artist name, and album name.

Elapsed file time:

The length of time that the current file has been playing

(default display).

File name:

Name of the current file.

Folder name:

Name of the current folder.

Title name:

Title of the current file (if ID3 tag present). When there

is no ID3 tag, the message “TITLE-NO DATA”

appears.

Artist name:

Name of the Artist (if ID3 tag present).

Album name:

Name of the album (if ID3 tag present).

Sampling rate and bit rate:

Sampling rate and bit rate of the current file.

Note

• To display the disc name, press DISPLAY while playback is

stopped.

• If a file or folder name contains any characters that cannot be

displayed, an underscore will appears in place of those

characters. Alternatively, you can set the compact disc player so

that names containing such characters are displayed as “FILE n”

or “FOLDER n”, “n” being the file or folder number. See “BAD-

NAME” for undisplayable characters setting (➔ 31).

Displaying Disc Information

Press DISPLAY repeatedly to show the following

disc information.

While playback is stopped

DISPLAY

Total number

of tracks

Total playing time

During playback or pause

REMAIN indicator

TOTAL indicator

Custom Setup

To cancel the procedure at any point, press SETUP.

Setup Procedures

Press SETUP.

Use #/$ or 7/6 to select the preference you

want to change.

The preferences are explained in the next column.

Press ENTER or 1.

Use #/$ or 7/6 to select the preference’s

options.

Press ENTER or 1.

When the preference has been set, “FINISH” appears

on the display.

7, 1, 6

SETUP

#, $

ENTER

■ FILTER

` SHARP (default)

This preference allows the band property up to

20 kHz to be output almost flat.

` SLOW

This preference brings higher reproducibility of

input waveform, and is suitable to reproduce

agogics, or subtle attack of sound signals, along with

sound image localization for each musical

instrument.

This preference configures the setting to switch the

characteristics of the digital filter for D/A conversion.

You can opt for whichever of the characteristics that

vary depending on your switching.

■ PHASE

` NORMAL (default)

The waveform recorded in disc will be output with

its polarity left intact.

` REVERSE

The waveform recorded in disc will be output with

its reversed polarity.

This preference configures the setting to switch the

phase of the analog audio output.

You may give it a try to switch and listen so that an

optimum sound quality can be obtained from the

amplifier and the speakers on line.

■ DISC

` DISPLAY (default)

` NOT

This preference determines whether or not the disc

name is displayed when an MP3/WMA CD is read.

■ FILE

` SCROLL (default)

` NOT

This preference determines whether or not the file name

scrolls across the display when an MP3/WMA file is

selected.

In Navigation mode, the file name scrolls across the

display regardless of this setting (➔ 23).

■ FOLDER

` SCROLL (default)

` NOT

This preference determines whether or not the folder

name scrolls across the display when an MP3/WMA

folder is selected.

In Navigation mode, the folder name scrolls across the

display regardless of this setting (➔ 23).

■ HIDE-NUM

` DISABLE (default)

Displays numbers.

` ENABLE

Hides numbers.

This preference determines whether or not the numbers

at the beginning of file and folder names are hidden.

When you create an MP3/WMA CD on a personal

computer, you cannot normally determine the playback

order of the files. However, if you number the

MP3/WMA files in order, starting with 01, 02, 03, and

so on, they will play in that order.

■ BAD-NAME

` NOT (default)

` REPLACE

This preference determines whether or not file and

folder names that contain undisplayable characters are

replaced with “FILE n.” or “FOLDER n.”, “n” being the

file or folder number. When set to “NOT”, displayable

characters are displayed and underscores are used in

place of any undisplayable characters. For ID3 tags,

underscores are used in place of undisplayable

characters regardless of this preference.

Preferences

AUDIO

DISPLAY

■ ID3-VER1

` READ (default)

` NO READ

This preference determines whether or not version

1.0/1.1 tags are read and displayed. When set to “NO

READ”, version 1.0/1.1 ID3 tags will not be displayed.

■ ID3-VER2

` READ (default)

` NO READ

This preference determines whether or not version

2.2/2.3/2.4 tags are read and displayed. When set to

“NO READ”, version 2.2/2.3/2.4 ID3 tags will not be

displayed.

■ CD-EXTRA

` AUDIO (default)

` MP3

This preference applies to CD Extra discs and

determines whether music in the audio session or

MP3/WMA files in the data session are played.

■ JOLIET

` USE SVD (default)

` ISO9660

This preference applies to MP3/WMA CDs in Joliet

format and determines whether the compact disc player

reads the SVD data or treats the disc as an ISO 9660

disc. Normally, this preference doesn’t need to be

changed. SVD (Supplementary Volume Descriptor)

supports long file and folder names and characters other

than letters and numbers.

■ STOP-KEY

` NAVI (default)

` FOLDER

` DISABLE

This preference determines how 2 on the compact disc

player works.

When the “NAVI” (Navigation) option is selected,

pressing 2 once selects Navigation mode.

When the “FOLDER” (ALL Folder) option is selected,

pressing 2 once selects All Folder mode.

When the “DISABLE” option is selected, compact disc

player does not enter Navigation or All Folder mode by

pressing 2.

Note

• This setting has no effect on the remote controller.

■ ASb (Auto Standby)

` ON

` OFF

For compact disc player playback, it is activated when

the playback is stopped for 30 minutes; however, it is

not activated when the playback is paused continuously.

Default setting: ON (European models), OFF (North

American models)

Note

• Before entering standby mode with the ASb function, the

Display Off LED flashes 30 seconds before the ASb function

starts running.

■ INITIAL

` CANCEL

` EXECUTE

This preference resets the compact disc player to

factory default.

Switch the output between DIGITAL/ANALOG,

DIGITAL, ANALOG in order.

EXTRA

ASb (Auto Standby)

INITIAL

Setting the Analog/Digital Output

Press OUTPUT MODE repeatedly on the front

panel.

The selected Audio output indicator lights.

` DIGITAL/ANALOG (default):

Uses both outputs.

` DIGITAL:

Uses the digital output only.

Turn the analog output off to perform more

stable playback.

` ANALOG:

Uses the analog output only.

Turn the digital output off to reduce the effect of

digital noise during playback.

OUTPUT MODE

Audio output indicator

Others

Troubleshooting

• Make sure that the power cord is properly plugged into

the wall outlet (➔ 18).

• Unplug the power cord from the wall outlet, wait 5

seconds or more, then plug it in again.

• When the set ASb starts running, the compact disc

player will automatically go Standby (➔ 32).

Power

Can’t turn on the Compact Disc Player.

The Compact Disc Player turns off

unexpectedly.

• Check all connections and correct as necessary (➔ 17).

• Make sure that there is no unsupported file formats or

signals.

• The compact disc player is equipped with a feature to

switch the digital/analog output. Check if the connection

between the compact disc player and a connected

component is appropriate, and also whether the selection

of the selector is correct.

• Make sure all audio connecting plugs are pushed in all

the way (➔ 17).

• The sound quality can be affected by strong magnetic

fields, such as that from a TV. Try moving any such

devices away from the compact disc player.

• If you have any devices that emit high-intensity radio

waves near the compact disc player, such as a cellular

phone that’s being used to make a call, the compact disc

player may output noise.

• The compact disc player’s precision drive mechanism

may emit a faint hissing sound while reading discs

during playback or when searching for tracks. You may

be able to hear this noise in extremely quiet

environments.

• The compact disc player is not a portable device. Use it

in a location that’s not subject to shock or vibration.

• Audio performance will be at its best about 10 to 30

minutes after the compact disc player has been turned on

and had time to warm up.

• Using cable ties to bundle audio cables with speaker or

power cables may degrade the sound quality. So don’t

do it.

Audio

There’s no sound.

The sound quality is not good.

Audio output is intermittent when the

Compact Disc Player is subjected to

vibration.

Audio performance

• The disc is upside down. Load the disc with the label-

side facing up (➔ 15, 22).

• The disc is dirty. Remove the disc and clean it (➔ 15).

• If condensation appears, unplug the power cord and

leave the compact disc player more than 3 hours at room

temperature.

• Make sure the disc is standard. See “Disc Note” (➔ 15).

• CD-R/CD-RW that are not finalized cannot be played.

• Install the compact disc player somewhere free of

vibration.

• The disc is dirty. Remove the disc and clean it (➔ 15).

• The disc is very scratched. Replace the disc.

• No such track on the disc. Enter another number (➔ 24).

• The disc is dirty. Remove the disc and clean it (➔ 15).

• The disc is very scratched. Replace the disc.

• Turn off any special playback modes (e.g. repeat,

memory, or random).

• Make sure the audio cable is connected correctly

(➔ 17).

• Make sure that all audio connecting plugs are pushed in

all the way (➔ 17).

• Make sure that the connected component’s input jack

and the input settings are correct.

• Make sure that the connected component’s volume isn’t

set to the lowest level, and that the volume isn’t muted.

• The disc is either scratched or dirty, and disc information

cannot be properly read.

• Make sure that the disc is not scratched or dirty.

• Due to a scratched or dirty disc, playback may not

operate normally or the sound may be jumpy.

• Make sure the batteries have been installed with the

correct polarity (+/–) (➔ 10).

• Replace both batteries with new ones. (Do not mix

different types of batteries or new and old batteries.)

• The remote controller is too far away from the compact

disc player, or there’s an obstacle between them (➔ 10).

• The compact disc player’s remote control sensor is being

subjected to bright light (inverter-type fluorescent light

or sunlight).

• The compact disc player is located behind the glass

doors of a audio rack or cabinet.

Disc Playback

Can’t play a disc.

Disc playback skips.

Can’t enter track numbers for memory

playback.

It takes a long time to locate certain

tracks.

Can not play tracks in the disc’s playback

order.

External Components

No sound is heard from a connected

component.

Display Unit

The message “99 --:--” appears.

Remote Controller

The remote controller doesn’t work

properly.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded

correctly.

The compact disc player contains a microcomputer

for signal processing and control functions. In very

rare situations, severe interference, noise from an

external source, or static electricity may cause it to

lockup. In the unlikely event that this should happen,

unplug the power cord, wait at least 5 seconds, and

then plug it again.

Before disconnecting the power cord from the wall

outlet, set the main power switch to OFF.

Specifications

Specifications and features are subject to change without notice.

C-7000R

Frequency Response 2 Hz - 20 kHz

Signal to Noise Ratio 116 dB

Audio Dynamic Range 100 dB

THD (Total Harmonic Distortion) 0.0015 %

Audio Output/Impedance

Optical

Coaxial

AES/EBU

–22.5 dBm

0.5 Vp-p / 75 Ω

3.3 Vp-p / 110 Ω

Rated RCA Output Level and Impedance 2.0 V (rms) / 330 Ω

Digital Outputs Optical: 1

Coaxial: 1

Analog Stereo Outputs L, R

Balance Output AES/EBU (DIGITAL)

Power Supply (North American) AC 120 V, 60 Hz

(European) AC 230 V, 50 Hz

Power Consumption (North American) 21 W

(European) 18 W

Standby Power Consumption (North American) 0.2 W

(European) 0.3 W

Dimensions (W × H × D) 435 W × 99 H × 315.2 D mm

(17-1/8 W × 3-7/8 H × 12-7/16 D inches)

Weight 12 kg (26.5 lbs)

Operation Condition Temperature/Humidity 5 ºC - 35 ºC/15% - 85%

Playable Discs Audio CD, CD-R, CD-RW, MP3, WMA (CD-R, CD-RW)

Discs that have not been properly finalized may only be

partially playable or not playable at all.

SN 29400529A

Y1102-2

* 2 9 4 0 0 5 2 9 A *

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

http://www.onkyo.com/

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650

http://www.us.onkyo.com/

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555

http://www.eu.onkyo.com/

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK

Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

Unit 1 & 12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung,

N.T., Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.ch.onkyo.com/

1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,

China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396

Onkyo C-7000R Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Onkyo C-7000R

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info