122714
14
Verklein
Vergroot
Pagina terug
1/152
Pagina verder
WWW.ONEFOR ALL.COM 13
If you should wish to remotely control lamps and lighting as well as Energy
Saving, you can also use the Energy Saver remote to control the separately
available One For All Light Accessories.
Lighting Control
- Voltage and Load: 230V~
- Degree of Protection: IP 20
- Radio Frequency: 433.92MHz
- RF Range: Typically 30m in open area.
- Max power for HC-8000: 1000 Watt
Specification HC-8000
It is possible to change the number you use to select the HC8000 Power Plug. This is useful
if you have purchased a second Power Plug (available from One For All), or if you already
have a Power Plug operating as number 1.
To assign a number to the plug, follow these steps:
Plug your device (or extension lead) the HC-8000 into the wall If you are
setting up a device with an in-line switch (such as a lamp), make sure the
switch is set to On
Press the Energy Saver key on your ONE FOR ALL URC-8350 so that it is
in Energy Saving Mode.
Press the number you wish to assign to the Power Plug Switch
(HC-8000). If this is your first Plug, number 1 is recommended, number 2
for the second etc. The IR Indicator (LED) at the top of the URC-8350
should blink twice.
Press and hold the button on the Power Plug (HC-8000) until the red
light begins to blink.
Press the Channel Up (+) key. The red light on the Light Power Plug
(HC-8000) should stop flashing.
The remote should now operate the Power Plug (HC-8000).
To test it, check if the Channel Up (+) and (-) keys work to switch your light ON
and OFF respectively,.
If you require more than 10 plugs to control, you can also use the Red, Green, Yellow
and Blue keys on your remote to control 11-14. Simply assign these keys to the Power
Plugs HC-8000) as you would do a number.
If you experience interference, it is possible to change the code of the Energy Saver
Mode on your remote to avoid this. The default code is 41000, but it is possible to
change the code to 41001, 41002 etc up to 41015. To change the code, set the Light
Mode up as you would do a normal device (see page 5), using codes 41000 - 41015.
If you should wish to reset your Power Plug HC-8000 to factory defaults so you can
assign it a new number, hold down the button on the Light Control Switch until the
red light starts to blink, release the button and then hold it down again until the red
light goes out.
How to change the number of your HC-8000
1
2
3
URC_8350_V_1_19feb08.qxd:Ofa5_Digital_URC7555_EURO_10_Talen 20-02-2008 16:07 Pagina 13
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw One for All urc 8350 energy saver bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van One for All urc 8350 energy saver in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools als bijlage per email.

De handleiding is 2,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info