NOTE: Please have your original remote controls handy before
performing learning on the Cinema 5.
1. Press and hold SETUP until the Cinema 5’s red
light blinks twice, then release SETUP.
2. Press 9 - 7 - 5. The Cinema 5’s red light will blink
twice.
3. Press and release the Device key in which you want
to learn a feature (e.g., TV).
NOTE: Steps 4 through 6 need to be completed within 10
seconds. Please read the next three steps before proceed-
ing.
4. Press and release the L key in which the new fea-
ture is to be learned. The Cinema 5’s red light will
flash rapidly.
5. Align your original remote control with the arrow
mark to the left of the LED on your Cinema 5
remote control (see diagram below)
NOTE: This diagram assumes that your original remote’s
LED is in the center. It may also be off center (to the right or
left side) If your Cinerma 7 will not take the command from
your original, try moving the originals alignment left or right
and see if the Cinema 5 accepts the signal from either posi-
tion.
6. On your original remote, press and hold the key
(feature) you want to learn until the red light on the
Cinema 5 blinks twice. (If the red light does not
blink twice, stop and repeat steps 1 through 6.)
NOTE: You can now repeat steps 3 through 6 to learn func-
tions on the other L keys.
7. Press and hold in the SETUP key until the Cinema
5’s red light flashes twice to lock in your new fea-
ture. (If the red light does not blink twice, stop and
repeat steps 1 through 6).
8. To test the new feature, press and release the
Device key in which the feature was learned fol-
lowed by the L key on which the feature was
learned.
Deleting Functions from the L Keys:
1. Press and hold in the SETUP key until the Cinema
5’s red light flashes twice and then release the
SETUP key.
2. Enter in 9 - 7 - 6.
3. Press and release the Device key (e.g., TV) where
the learned feature to be deleted is stored.
4. Press the L key to be deleted twice. The Cinema
5’s red light will blink twice after the second press
of the L key.
SETTING UP OTHER COMPONENTS
In addition to the components labeled on the device keys
(TV, VCR, DVD/LD, CBL/SAT, etc.), the Cinema 5 can also
operate the following components: Cassette Decks, Infrared
Home Automation, MiniDisc, Video Accessories and Miscel-
laneous Audio Components (Graphic Equalizers and Digital
Music Service Boxes).
The Setup Codes for these components can be accessed
under the following device keys:
Cassette Decks: Use the VCR Key
IR Home Automation: Use the CD Key
MiniDisc: Use the CD Key
Video Accessories: Use the CBL/SAT Key
(Note : WebTV found under Video Accessories)
Miscellaneous Audio: Use the AUX or RCVR Key
For example, to set up a Cassette Player on the VCR key:
1. Turn on your Cassette Player and insert a tape.
2. Press VCR and release. Press and hold SETUP
until the Cinema 5’s red light blinks twice, then
release SETUP.
3. Enter the first four-digit Cassette Player code listed
for your brand in the “Setup Codes For Audio
Cassettes” section. If you perform this procedure
correctly, the red light will blink twice when you
enter the final digit of your code.
4. Aim the Cinema 5 at your Cassette Player and
press PL (Play).Your unit should play the tape. If it
does not respond, repeat steps 2-4, trying each
code listed for your brand until you find the one
that works.
5. Your Cinema 5 is now programmed to operate
your Cassette Player.
Remember, if you want to use your Cinema 5 to operate
your Cassette Player, press the VCR key first.
Setup Codes For Audio Cassettes
Aiwa 0029, 0197
Bang & Olufsen 0219
Carver 0029
Denon 0076
Harman/Kardon 0182
JVC 0244
Magnavox 0029
Marantz 0029
Optimus 0027, 0220
Philips 0029
Pioneer 0027, 0220
Sansui 0029
Sony 0170, 0243, 0291
Victor 0273
Wards 0027
Yamaha 0097
Setup Codes For IR Home Automation
GE 0240
Lutron 0318, 0597
One For All 0167
RadioShack 0240
Security System 0167
Universal X10 0167
X10 0167
