492786

One for All URC-5705 Handleiding

1
Verklein
Vergroot
Pagina terug
1/1
Pagina verder
INTRODUCTION
The One For All Access 5 Universal
Remote Control is designed to operate
five home entertainment devices,includ-
ing TV,video,and audio components.
The remote control requires two fresh
AAA alkaline batteries (not included) and
easy programming to control your devices.
For best results,please read and perform
all instructions listed here.Also,keep
these instructions for future reference.
FEATURES AND FUNCTIONS
Use the Key Charts to learn how to use the
universal functions of the One For All
Access 5 Universal Remote Control.
Key Charts
Use SETUP for all
programming
sequences.
The LED (red light)
blinks to show that
the remote control is
working and is
sending signals.
Press POWER once to
turn on or off the
selected device.
Press VCR/DVD,AUX,
RCR/AMP,CBL/SAT,or
TV once to select a
home entertainment
device to control.
Use the keypad (0~9)
to directly select
channels (for example,
09 or 31).
Press MUTE once to
turn sound off or on.
Press PREV once to
recall the last-viewed
channel and to page
back one screen on the
main menu.
Press ENTER once
after entering channel
numbers on some TVs.
Press SLEEP to activate
your device’s sleep
timer (not available
for all devices).
Press SHIFT and use
the Up/Down/Left
Right cursor keys to
move the cursor in the
program guide and
menu screens.
Press SHIFT and MUTE
to select a menu item.
Use VOL+ (or VOL-)
to raise (or lower) the
sound volume.
Use CH
▲ (or CH▼) to
select the next higher
(or lower) channel.
When controlling a
DVD/CD player,use
SKIP FORWARD (or
SKIP REV) to skip to
the next (or previous)
DVD chapter/CD track.
Press MENU once to
display your selected
device’s main menu.
Use EXIT to exit from
your selected device’s
menu or guide.
Use GUIDE to display
your selected device’s
program guide.
Use INFO to display the
current channel and
program information.
Use the transport keys
to control your VCR,
CD or DVD player,or
VOD. To record a
program,press the
record key (
•
) twice.
Use TV/VID to switch
the TV’s input to view
TV or video programs.
INSTALLING BATTERIES
1. On the remote control’s back,push the
tab and lift off the battery cover.
2. Obtain two (2) new AAA alkaline
batteries.Match the + and – marks
on the batteries to the + and –
marks in the battery case,then insert
the new batteries.
3. Press the battery cover back into
place.The tab should click when the
cover is locked.
4. Test the unit by pressing POWER and
any mode key (e.g.,TV).If batteries
are inserted correctly,the LED will
blink once.
NOTE:When batteries need replacement,
the remote control will stop operating.
Remove the old batteries and insert new
ones within 30 minutes to ensure all of
your programming information is restored.
PROGRAMMING
DEVICE CONTROL
The One For All Access 5 remote control
is preprogrammed at the factory to
operate an RCA TV and VCR,a Motorola
(GI) cable box,a Pioneer audio tuner,
and a Radio Shack X-10 home automa-
tion unit.To control devices other than
the default brands,perform the follow-
ing steps; otherwise skip this section:
NOTE:For TV/VCR Combo control,see the
next section.
1. Turn on a device (e.g.,VCR) and,if
applicable, insert media, (e.g.,
cassette or disc).
NOTE: Please read steps 2-4 completely
before proceeding. Highlight or write down
the codes and device you wish to program
before moving on to step 2.
2. On the remote control,press a
device key once (i.e., VCR/DVD,AUX,
RCR/AMP,CBL/SAT,or TV).Press and
hold SETUP until the LED blinks
twice,then release SETUP.
3. Use the Manufacturer’s Codes to
locate the the type of device and
brand name and then enter the first
four-digit code for your device.If
performed correctly,the LED will
blink twice.
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
4. Aim the remote control at the device
and press POWER once.The device
should turn off.If it does not respond,
repeat steps 2-3,trying each code for
your brand until you find one that
works.If it still does not work,try
Searching For Your Code.
NOTE: If the device does not have a
POWER
key,press the (
Play
) key.
5. Repeat steps 1 through 4 for each
device you want to control.
PROGRAMMING
TV/VCR COMBO CONTROL
Perform the following instructions to
control a TV/VCR Combo:
1. Turn on the TV/VCR Combo and
insert a video cassette.
NOTE: Please read steps 2-4 completely
before proceeding. Highlight or write down
the codes and device you wish to program
before moving on to step 2.
2. On the remote control,press VCR/DVD.
Press and hold SETUP until the LED
blinks twice,then release SETUP.
3. Use the Setup Codes For TV/VCR
Combos (on the back side) to locate
the brand name and then enter the
first four-digit code for your device.
If performed correctly,the LED will
blink twice.
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
4. Aim the remote control at the device
and press POWER once.It should turn
off.If the device does not respond,
repeat steps 2-3,trying each code for
your brand until you find one that
works.If it still does not work,try
Searching For Your Code.
NOTE: If the device does not have a
POWER
key,press the (
Play
) key.
SEARCHING FOR YOUR CODE
If your device does not respond to the
remote control after trying all codes
listed for your brand,or if your brand is
not listed at all,try searching for your
code. For example,to search for a code
for your TV:
1. On the remote control,press TV once.
2. Press and hold SETUP until the LED
blinks twice,then release SETUP.
3. Enter 9 - 9 - 1.The LED will
blink twice.
4. Aim the remote control at the the
TV and slowly alternate between
pressing POWER and TV. Stop when
the TV turns off.
NOTE:In the search mode,the remote
control will send IR codes from its library
to the selected device,starting with the
most popular code first.
5. To lock in the code,press and hold
SETUP until the LED blinks twice,
then release SETUP.
6. To search for the codes of your other
devices,repeat steps 1 through 5,but
substitute the appropriate device key
for the device you are searching for.
CHECKING THE CODES
If you have set up the remote control
using the Searching For Your Code
procedure,you may need to find out
which four-digit code is operating your
equipment:
For example,to find out which code is
operating your TV:
1. On the remote control,press TV once.
2. Press and hold SETUP until the LED
blinks twice,then release SETUP.
3. Enter 9 - 9 - 0.The LED will
blink twice.
4. To view the code for the first digit,
press 1 once.Wait 3 seconds,count
the LED blinks (e.g.,3 blinks = 3)
and write down the number.
NOTE:If a code digit is “0”,the LED will
not blink.
5. Repeat step 4 three more times for
remaining digits.Use 2for the
second digit,3for the third digit,
and 4 for the fourth digit.
6. To check for codes of other devices,
repeat steps 1 through 5,but substi-
tute the appropriate device key for
each device you are checking.
As before,write down each four-
digit code.
RE-ASSIGNING DEVICE KEYS
The One For All Access 5 can be set to
control a second TV,VCR,DVD player,or
audio device.
For example,to control a TV,a cable box,
and two VCRs,you will need to re-assign
the unused AUXkey to operate the sec-
ond VCR as follows:
1. On the remote control,press and
hold SETUP until the LED blinks
twice,then release SETUP.
2. Enter 9 - 9- 2.The LED will
blink twice.
3. Press VCR once,then press AUX once.
4. The AUX key is now ready to be pro-
grammed for your second VCR.See
Programming Device Control.
To re-assign other device keys,repeat
steps 1 through 4 by substituting the key
sequence from the below chart for the
most popular devices:
To Re-Assign Key
Sequence Perform
VCR/DVD as
2nd TV key: SETUP - 9 - 9- 2
- TV - VCR/DVD
VCR/DVD as 2nd
CBL/SAT key: SETUP - 9 - 9 - 2
-CBL/SAT- VCR/DVD
VCR/DVD as 2nd
RCR/AMP key: SETUP - 9 - 9 - 2
-RCR/AMP- VCR/DVD
VCR/DVD back to
VCR/DVD: SETUP - 9 - 9 - 2
-VCR/DVD - VCR/DVD
RCR/AMP as
2nd TV key: SETUP - 9 - 9- 2
- TV - RCR/AMP
RCR/AMP as 2nd
VCR/DVD key: SETUP - 9 - 9 - 2
- VCR/DVD-RCR/AMP
RCR/AMP as 2nd
CBL/SAT key: SETUP - 9 - 9 - 2
-CBL/SAT- RCR/AMP
RCR/AMP back to
RCR/AMP: SETUP - 9 - 9 - 2
-RCR/AMP-RCR/AMP
AUX as
2nd TV key: SETUP - 9 - 9- 2
- TV - AUX
AUX as 2nd
VCR/DVD key: SETUP - 9 - 9 - 2
- VCR/DVD- AUX
AUX as 2nd
CBL/SAT key: SETUP - 9 - 9 - 2
-CBL/SAT- AUX
AUX back to
AUX: SETUP - 9 - 9 - 2
-AUX-AUX
When a re-assignment is done,the LED
will blink twice to confirm your choice.
At that time,you will need to program
the remote control for the new device
(see Programming Device Control).
CHANGING VOLUME LOCK
The One For All Access 5 is set to
control the volume of your TV in the TV,
VCR/DVD,CBL/SAT, RCR/AMP,and
AUX modes.If you want volume to be
controlled by a mode other than TV
(e.g.,CBL/SAT),change the Volume Lock
setting as follows:
To Change Volume Lock To Be
Controlled By Another Mode:
1. On the remote control,press and
hold SETUP until the LED blinks
twice,then release SETUP.
2. Enter 9 - 9- 3 and then press any
mode key once (except TV).The LED
will blink twice.
3. Now,whenever you press VOL+,
VOL–,or MUTE,volume will be
controlled by your mode choice.
Unlocking Volume Control:
NOTE:Perform these instructions when you
want independent volume control for each
programmed device (e.g.,TV volume control
in TV mode,CBL/SAT volume in CBL/SAT
mode,etc.)
1. On the remote control,press and
hold SETUP until the LED blinks
twice,then release SETUP.
2. Enter 9 - 9- 3 and then press VOL+.
The LED will blink four times.
3. Volume will again be controlled
according to its default states.
TROUBLESHOOTING
For assistance,please contact us in any
of the following ways:
• Consumer Help Line: (330) 405-8612
• Internet: http://www.oneforall.com
PROBLEM: If you own a satellite that
uses code 0775 (Express
Vu and Echostar) and
your exit key does not
work,perform the follow-
ing sequence to activate
this feature/function.
SOLUTION: 1. Press the CBL/SAT key
2. Press and hold the SET
key until the red LED
blinks twice
3. Press 9-9-4,the red
LED will blink twice
4. Press SET and release
(one blink on LED)
5. Press 3-3-6
6. Press the EXIT key, the
red LED will blink
twice.
The Exit key will now
correctly perform the exit
feature/function on your s
satellite.
PROBLEM: LED does not blink when
you press a key.
SOLUTION: Replace batteries with two
new
AAA
alkaline batteries.
PROBLEM: LED blinks when you
press a key,but home
entertainment device
does not respond.
SOLUTION: Make sure the remote
control is aimed at your
home entertainment
device and is not farther
than 15 feet away.
PROBLEM: The unit does not control
home entertainment
devices or commands are
not working properly.
SOLUTION: Try all listed codes for the
device brands being
set up.Make sure they
can be operated with an
infrared remote control.
PROBLEM: TV/VCR combo does not
respond properly.
SOLUTION: Use the VCR codes for
your brand.Some combo
units may require both a
TV code and a VCR code
for full operation.
PROBLEM: Changing channels does
not work properly.
SOLUTION: If original remote control
required pressing ENTER
to change channels, press
ENTER on the remote
control after entering the
channel number.
PROBLEM: Tried “Search Method”
and still could not find a
working code.
SOLUTION: Clear the device key as
follows: Press and hold
SETUP until the LED
blinks twice,then release.
Next enter 9 - 9 - 2.Then
press the device key to be
cleared twice.Now repeat
the “Search Method.”
PROBLEM: Remote control does not
turn on Sony or Sharp
TV/VCR Combo.
SOLUTION: For power on,these prod-
ucts require programming
TV codes.For Sony, use
TV code 0000 and VCR
code 0032.For Sharp,use
TV code 0093 and VCR
code 0048.
PROBLEM: CH
▲ and CH▼ do not
work for your RCA TV.
SOLUTION: Due to RCA design (1983-
1987),only the original
remote control will oper-
ate these functions.
LIFETIME WARRANTY
One For ALL ("OFA") warrants this product to be free
from defects in materials and workmanship,under nor-
mal use,throughout the period of the product’s owner-
ship by the original purchaser.This warranty does not
cover damage or failures caused by products or services
not supplied by OFA,or which result from accident,mis-
uses, abuse,neglect, mishandling,misapplication,faulty
installation,set-up adjustment,improper maintenance,
alteration, maladjustment of consumer controls, modifi-
cations,commercial use,or that is attributable to acts of
God.
There are no express warranties except as listed above.
OFA SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THIS PRODUCT OR ARISING OUT OF ANY
BREACH OF WARRANTY,ALL EXPRESS AND
IMPLIED WARRANTIES, INCLUDING THE WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE,ARE LIMITED TO THE
WARRANTY PERIOD SET FORTH ABOVE.Some states
do not allow the exclusion or limitation of incidental or
consequential damagers,or limitations on how long an
implied warranty lasts,so the above exclusions or limi-
tations may not apply to you.This warranty gives you
specific legal rights and you may also have other rights
which vary from state to state.
To obtain warranty service for a defective product,
please return the product,preferably in the original car-
ton, along with your purchase receipt,to the store of
original purchase for the first 90 days.A note detailing
the complaint would be helpful.The store,at its option,
will replace or repair this product if found to be defec-
tive.
If the unit has been purchased more than 90 days ago,
pls return it to Impact Distribution Services, 6262
Patterson Pass Road,Suite C,Livermore,CA 94550
together with the original receipt and $3.95 to cover
postage and handling.It will be repaired or replaced at
the manufacturer’s option.The manufacturer reserves
the right to substitute a currently manufactured model
with equal or superior features.
ADDITIONAL INFORMATION
ONE FOR ALL® is the registered trademark of
Universal Electronics Inc.Computime International Ltd.
is the Licensee of the ONE FOR ALL® brand for USA
and Canada.
Copyright 2001 by Universal Electronics Inc.No part of
this publication may be reproduced,transmitted,tran-
scribed, stored in any retrieval system,or translated to
any language,in any form or by any means,electronic,
mechanical, magnetic,optical,manual,or otherwise,
without the prior written permission of Universal
Electronics Inc.
One For All® Access 5 is compatibile for use in North
America excluding Mexico.
URC-5705/5741w 03/02
REW
PLAY
PAUSE STOP
FF
POWER
REW
REC
PLAY
TV/VID
PAUSE
STOP
FF
POWER
78
0
ENTER
SHIFT
PREV
SKIP FWD
SKIP REV
SLEEP
CH
CH
VOL ––
VOL
+
MUTE
MENU
EXIT
GUIDE
INFO
9
45
6
12
3
SET
TV
AUX
VCR
DVD
RCR
AMP
CBL
SAT
ACCESS 5
UNIVERSAL REMOTE CONTROL
USER’S GUIDE
SKIP FWD
SKIP REV
SHIFT
CH
CH

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw One for All URC-5705 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van One for All URC-5705 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info