SAFET
INTENDED USE
This product is designed to measure the blood pressure and pulse rate of people within
the range of the designated arm cuff, following the instructions in this instruction
manual. It is mainly designed for general household use. Please read the “Safety
Information” in this instruction manual before using the unit.
T
followed including the warnings and cautions listed in this instruction manual.
OPERA
Contact your physician for specific information about your blood pressure.
Self-diagnosis and treatment using measured results may be dangerous. Follow the
instructions of your physician or licensed healthcare provider
DO NOT adjust medication based on measurement results from this blood pressure
monitor
qualified to diagnose and treat High Blood Pressure.
The monitor is not intended to be a diagnostic device.
If battery fluid should get in your eyes, immediately rinse with plenty of clean
water
Read all of the information in the instruction manual and any other literature in the
box before operating the unit.
Do not use this device on infants or persons who cannot express their intentions.
Read the Special Conditions section of the instruction manual if your systolic
pressure is known to be more than 220 mmHg. Inflating to a higher pressure than
necessary may result in bruising where the cuff is applied.
Operate the device only as intended. Do not use the device for any other purpose.
Dispose of the device, components and optional accessories according to applicable
local regulations. Unlawful disposal may cause environmental pollution.
Do not use a cellular phone near the device. It may result in an operational failure.
Use only Omron authorized parts and accessories. Parts and accessories not
approved for use with the device may damage the unit.
Do not use other types of batteries. This may damage the unit.
Do not use in a location with moisture, or a location where water may splash on the
unit.
CARE AND
Do not subject the monitor to strong shocks, such as dropping the unit on the floor
Do not submerge the device or any of the components in water
Store the device and the components in a clean, safe location.
Changes or modification not approved by the manufacturer will void the user
warranty
SAFETY
W
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury
CAUTION
Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury to the user or patient or
damage to the equipment or other property
BEFORE
T
1.
before taking a measurement. Rest for at least 15 minutes before taking the
measurement.
2. Stress raises blood pressure.
3. Measurements should be taken in a quiet place.
4. Remove tight-fitting clothing from your left arm.
5. Sit on a chair with your feet flat on the floor
cuff is at the same level as your heart.
6. Remain still and do not talk during the measurement.
7. W
to the condition prior to taking the blood pressure measurement.
increase the wait time depending on your individual physiological characteristics.
8. Keep a record of your blood pressure and pulse readings for your physician.
single measurement does not provide an accurate indication of your true blood
pressure.
measure your blood pressure at the same time each day for consistency
INSTRUCTION MANU
5 series
Blood Pressure Monit
Model BP742
INTRODUCTION
Thank you for purchasing the OMRON
®
BP742 5 series
Monitor
Y
measurement. This means the monitor detects your blood’
brachial artery and converts the movements into a digital reading.
monitor does not need a stethoscope so the monitor is simple to use.
The BP742 comes with the following components:
• Monitor • W
• 4 “AA”
• Instruction Manual printed in English and Spanish • Quick Start Guide
The BP742 5 series
Please read this instruction manual thoroughly before using the unit.
Please keep for future reference.
For specific information about your own blood pressure, CONSUL
DOCTOR.
Ffor
DA __________________
SERIAL NUMBER: ____________________
• Staple your purchase rec
• Register your product on-line at
www
SA
LIMITED W
Y
batteries, is warranted to be free from defects in materials and workmanship appearing
within 2 years from the date of purchase, when used in accordance with the instructions
provided with the monitor
materials and workmanship appearing within one year from the date of purchase when
the monitor is used in accordance with the instructions provided with the monitor
above warranties extend only to the original retail purchaser
W
covered by the above warranties. Repair or replacement is our only responsibility and
your only remedy under the above warranties.
T1-800-634-4350 for the
address of the repair location and the return shipping and handling fee.
Enclose the Proof of Purchase. Include a letter
number
damage in transit. Because of possible loss in transit, we recommend insuring the
product with return receipt requested.
THE FOREGOING IS THE SOLE
CONNECTION WITH
ANY
W
PURPOSE. IMPLIED W
IMPOSED BY
OF
OMRON SHALL
SPECIAL, INCIDENT
EXPENSES OR DAMAGES.
This warranty provides you with specific legal rights, and you may have other rights
that vary by jurisdiction. Because of special local requirements, some of the above
limitations and exclusions may not apply to you.
FOR CUSTOMER SER
V
Call toll free: 1-800-634-4350
Note:
POTENTIAL
This product has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. The product generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However
guarantee that interference will not occur in a particular installation. If the product does
cause harmful interference to radio or television reception, which can be determined by
turning the product on and off, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver
• Connect the product into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
POTENTIAL
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus as set out in the interference-causing equipment standard entitled
“Digital
Cet appareil numérique respecte les limites de bruits radioeléctriques applicables aux
appareils numériques de Clase B prescrites dans la norme sur le materiel brouilleur:
“Appareils Numériques”, ICES-003 édictée par le minister des communications.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user
SPECIFICA
Model:
Display:
Measurement Range:
Accuracy/Calibration:
Inflation:
Deflation:
Rapid Air Release:
Measurement Method:
Po
Battery Life:
Operating T
/Humidity
Storage T
/Humidity/Air Pressure:
Main
Main Unit Dimensions:
Cuff Size:
Cuff Circumf
Memory
Contents:
Optional Accessories:
BP742 (HEM-7200-Z)
LCD Digital Display
Pressure: 0 to 299 mmHg, Pulse: 40 to 180/min.
Pressure: ±3mmHg or 2% of reading
Pulse: ±5% of reading
Automatic by electric pump
Automatic pressure release valve
Automatic exhaust valve
Oscillometric method
1.5V 4 “AA” batteries
Approx. 300 uses with 4 new alkaline batteries
50ºF to 104ºF (10ºC to 40ºC) /15 to 90% RH
-4ºF to 140ºF (-20ºC to 60ºC) /10 to 95% RH
700-1060 hPa
Approximately 12 oz. (340g)
not including batteries
Approx. 5 l/2"(l) × 4 7/8"(w) × 3 3/8" (h)
(141 mm × 123 mm × 85 mm)
Approx. 6"(w) × 22 1/8"(l) (151 mm × 563 mm)
Cuff tube 35 3/8" (900 mm)
Fits arm circumferences 9" to 17"
(220 mm to 420 mm)
Up to 30 readings per user
Main Unit, W
“AA”
Alkaline
Instruction Manual, and Quick Start Guide
AC Adapter
NOTE: These specifications ar
Manufactured for OMRON HEAL
Distributed by OMRON HEAL
1925 W
Lake Forest, IL
www
© 2012 OMRON HEAL
Made in V
FC
HEM-7200-Z(V)_C_M02_120928.pdf
SET
Set the monitor to the current date and time before taking a measurement for the first
time. If the date and time are not set correctly
memory and the average values may not be correct.
1. T
Press the Date/T
The year flashes on the display
2. SETTING THE
The year can be set between 2010 and 2040. When the
display reaches 2040, it will return to 2010.
Press the Up button ( ) to advance by one year
Press the Date/T
year
The month flashes on the display
NOTES: • Press the Down button ( ) to decrease the
date and time values.
• Press and hold the button to increase or
decrease the date and time values faster
3. SETTING THE MONTH
Press the Up button ( ) to advance by one month.
Press the Date/T to set the current
month.
The day flashes on the display
4. SETTING THE DA
Press the Up button ( ) to advance by one day
Press the Date/T
day
The hour flashes on the display
5. SETTING THE HOUR
The time is set using
Press the Up button ( ) to advance by one hour
Press the Date/T
hour
The minute flashes on the display
6. SETTING THE MINUTE
Press the Up button ( ) to advance by one minute.
Press the Date/T
7. TO TURN THE MONITOR OFF
Press the ST
NOTE: The monitor will automatically turn of
been set.
W
If battery fluid should get in your eyes, immediately rinse with
plenty of clean water
CAUTION
Read all of the information in the instruction manual and any other
literature in the box before operating the unit.
CAUTION
This device is intended for use in measuring blood pressure and
pulse rate in the adult population. Do not use this device on infants
or persons who cannot express their intentions.
APPL
1. Make sure the air plug is securely inserted
in the main unit.
2. Remove tight-fitting clothing from your upper
arm.
3.
the arrow is centered on the inside of your arm
and aligned with your middle finger
The air tube runs down the inside of your arm.
The bottom of the cuff should be
approximately 1/2 " above your elbow
4. W
arm using the cloth fastening.
APPL
When taking a measurement using the right arm, use this instruction for Step 3.
Apply the cuff to your right upper arm so
the arrow and the air tube runs along the inside
of your arm. The bottom of the cuf
approximately 1/2 " above your elbow
NOTE: Be careful not to rest your arm on the air tube. This will restrict the flow of air
to the cuff.
APPL
1/2 inch
Air T
Arrow
Left Arm
Right Arm
Arrow
T
1.
Press
All symbols appear on the display
2.
3. Sit on a chair with your feet flat on the floor
Place your arm on a table so the cuff is level
with your heart.
Keep still and do not talk during measurement.
4.
The cuff starts to inflate automatically
determines your ideal inflation level.
Remain still and do not move your arm until the entire measurement process is completed.
NOTE: T
monitor will stop inflating, start deflating, and will turn off.
5. Inflation stops automatically and the measurement is started.
As the cuff deflates, decreasing numbers appear on the display and the Heartbeat
Symbol ( ) flashes.
6. When the measurement is complete, the arm cuf
deflates.
7. Press the ST
NOTE: The monitor will automatically turn off after
five minutes.
CARE AND MAINTENANCE
T
damage, follow the dir
Do not forcefully bend the arm cuf
Clean the monitor with a soft dry cloth.
Do not use any abrasive or volatile cleaners.
Do not attempt to clean the cuff.
CAUTION
Do not submerge the device or any of the components in water
not subject the monitor to extreme hot or cold temperatures,
humidity or direct sunlight.
CAUTION
Store the device and the components in a clean, safe location.
CAUTION
Do not subject the monitor to strong shocks, such as dropping the unit on the floor
Remove the batteries if the unit will not be used for three months or longer
replace all the batteries with new ones at the same time.
Use the unit in a manner consistent with the instructions pr
CAUTION
Use only Omron authorized parts and accessories. Parts and accessories
not approved for use with the device may damage the unit.
CAUTION
Changes or modification not approved by the manufacturer will void the user
warranty
TROUBLESHOO
PROBLEM
No power
No display appears on the unit.
Measurement values appear too
high or too low
CAUSES AND SOL
Replace all four batteries with new ones.
Check the battery installation for proper placement
of the battery polarities.
Blood pressure varies constantly
including stress, time of day
cuff, may af
Review the sections “Before T
Measurement” and “T
ERROR INDICA
SYMBOL CAUSE
Device error
CORRECTION
Keep still and take another
measurement.
Replace the four batteries.
Refer to “Battery Installation”.
Contact Customer Service.
Remove the arm cuff.
minutes and then take another
measurement. Repeat the steps in
section “Applying the
If this error continues to appear
contact your doctor
Batteries are low
Irregular or weak
pulses are detected.
Movement during
measurement.
Monitor could not
detect pulse wave.
Cuff over
Cuff under
Cuff not applied
correctly
T
remain still until the measurement
is complete.
Remove the arm cuff.
Read “T
W
T
1. Press the indicator on the battery cover and
slide the cover off in the direction of the arrow
2. Install 4 “AA” size batteries so the + (positive) and
- (negative) polarities match the polarities of
the battery compartment as indicated.
3. Replace the battery cover
BA
Low Battery Indicator
When the Low Battery Indicator appears on the display
remove all the batteries. Replace with four new batteries at the same time. Long-life
alkaline batteries are recommended.
NOTES: • T
while the unit is still on, the date and time will be reset to that of the
previous use. However
• When the batteries are replaced, you may need to reset the date and time. If
“-:--” appears on the display
• The supplied batteries may have a shorter life.
CAUTION
Dispose of the device, components and optional accessories according to
applicable local regulations. Unlawful disposal may cause environmental
pollution.
BA
UNIT DISPLA
Systolic blood pressure
Diastolic blood pressure
Memory symbol
(Displayed when viewing
values stored in memory)
A
Heartbeat symbol /
Hypertension Indicator
Irregular Heartbeat symbol
User ID symbol (A/B)
Pulse display
Deflation symbol
Battery low indicator
Date/Time Display
Movement error symbol
KNOW Y
Main Unit:
Components:
ST
USER ID
Selection Switch
Up/Down ( ) buttons
Air Jack
Date/Time setting ( )
button
Wide Range Cuff
Air tube
Air plug
Quick Start
Guide
Instruction
Manual
Display
INSTRUCTION MANUAL
INTRODUCTION
Thank you for purchasing the OMRON
®
BP742 5 series Automatic Blood Pressure
Monitor.
Your new digital blood pressure monitor uses the oscillometric method of blood
pressure measurement. This means the monitor detects your blood’s movement through
your brachial artery and converts the movements into a digital reading. An
oscillometric monitor does not need a stethoscope so the monitor is simple to use.
The BP742 comes with the following components:
• Monitor • Standard Adult Arm Cuff
• Instruction Manual printed in English and Spanish • Quick Start Guide
The BP742 IntelliSense
®
Automatic Inflation Blood Pressure Monitor is intended for
home use.
Fill in for future reference.
DATE PURCHASED:__________________
SERIAL NUMBER: ____________________
Staple your pur chase re c eipt here
SAVE THESE INSTRUCTIONS
5329898-7C
Battery compar
AC adapter Jack
BP742
5 Series Arm B loo dessu re
Monitor
5 series
Blood Pressure Monitor
Model BP742
DISPLA
IRREGULAR HEAR
When the monitor detects an irregular rhythm two or more times during the
measurement, the Irregular Heartbeat Symbol ( ) will appear on the display with the
measurement values.
An irregular heartbeat rhythm is defined as
a rhythm that varies by less than 25% from
the average rhythm or 25% more than the
average rhythm detected while the monitor
is measuring the systolic and diastolic
blood pressure.
If the irregular heartbeat symbol ( )
displays with your measurement results,
we recommend you consult your
physician. Follow the directions of your
doctor
MOVEMENT ERROR SYMBOL
The Movement Error Symbol ( ) is displayed if you move your body during the
measurement. Please remove the arm cuff, and wait 2-3 minutes. Reapply the arm cuf
and take another measurement.
A
The
The most recent average reading appears on the display screen.
HEAR
T
The Heartbeat Symbol ( ) flashes on the display during the measurement. The
Heartbeat Symbol ( ) flashes at every heartbeat.
When the measurement is complete, the Heartbeat Symbol ( ) flashes on the
display with your blood pressure and pulse rate if the reading is above 135 for the
Systolic Blood Pressure value and/or above 85 for the Diastolic Blood Pressure
value.
USING THE MEMOR
The Heartbeat Symbol ( ) flashes when the blood pressure reading stored in the
memory is above 135 for the Systolic Blood Pressure value and/or above 85 for the
Diastolic Blood Pressure value.
Internationally recognized guidelines for upper limit of normal home blood pressure
readings are as follows:
This is a general guideline because blood pressure depends on age and morbidity
A
including diabetic patients, pregnant women, and patients with renal failure.
OMRON HEAL
Symbol ( ) flashes on the display with your measurement values.
W
The monitor is not intended to be a diagnostic device.
W
Contact your physician for specific information about your blood pressure.
Self-diagnosis and treatment using measured results may be dangerous.
Follow the instructions of your physician or licensed healthcare provider
Normal
Irregular Hear
Shor Long
Blood
pressure
Pulse
Pulse
Blood
pressure
Home Guideline for Upper
Systolic Blood Pressure 135 mmHg
Diastolic Blood Pressure 85 mmHg
SPECIAL
CAUTION
Inflating to a higher pressure than necessary may result in bruising where
the cuff is applied.
If your systolic pressure is known to be more than 220 mmHg, press and
hold the ST
higher than your expected systolic pressure.
NOTES: • Do not apply more pressure than necessary
• The monitor will not inflate above 299 mmHg.
When the measurement is complete, the arm cuff completely deflates.
Y
USING
The monitor is designed to store the blood pressure and the pulse rate in the memory
for two people (USER
The monitor automatically stores up to 30 sets of measurement values (blood pressure
and pulse rate) for each user (A
stored, the oldest record is deleted to save the most recent values.
A
The monitor calculates the average reading based on the three most recent sets of
measurement values taken within 10 minutes of the most recent reading.
NOTE: If two sets of measurement values are stored in the memory for the 10
minutes period, the average is based on the two sets of measurement values.
If one set of measurement values is stored, this is displayed as the average.
TO DISPLA
1. Press the ST
2. Select your USER ID (A
3. Press the Up or Down button ( ). The
on the display when the average reading is shown.
4. Press the Up or Down button ( ) to display the sets of measurement values.
Press the Down button ( ) r
A
back to the average value
Press the Up button ( ) r
A
back to the average value
NOTES: • The measurement value number is displayed
briefly in the Pulse Display area when you press
the Up/Down buttons ( ) .
• The date and time are alternately displayed with
the measurement values.
• If the date and time are not set, “-:--” is displayed
with the measurement values.
• Press the button repeatedly to display the next
values.
• Press and hold the button to display the values
faster
TO DELETE
The values stored in the memory are deleted by USER ID.
Y
the user you select will be deleted.
1. Press the ST
2. Select your USER ID (A
3. While holding the Down button ( ), press the ST
more than five seconds until the display appears as it does in the following
illustration.
4. Press the ST
NOTE: The monitor will automatically turn off after five minutes.
Alternating
display
