812264
70
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
Installation instructions
for the specialist company
LEVANA 2.0 6 kW
LEVANA 2.0 8 kW
LEVANA AQUA 2.0
ARINA 2.0
INARA 2.0
EN
2.8 LEVANA AQUA 2.0 water installation
Water side connection
The water pipes can optionally be laid to the rear (installed in the
factory) or to the bottom through the oor.
For laying through the oor, you must remove the lower rear wall
and adjust the mounting for the ow and return ow accord-
ingly. For laying of the water pipes through the oor, as well as for
removal / installation of the rear cladding, follow a similar procedure
to that which is set out in the “Combustion air nozzles for connec-
tion from the bottom chapter.
5431 2
Fig. 2.36 Water side connections on the rear of the pellet replace
1Socket for connection of the 3-pole connector for the pump
2Socket (pastel blue) for the top buer sensor connection
3Socket (light blue) for the bottom buer sensor connection
4½” heating return
5½” heating ow
Important information for integration of the pellet re-
place into the heating system and/or domestic cooling
water system:
ū The water connections and the electrical work may only be car-
ried out by expert technicians.
ū We recommend the “Olsberg installation unit” (item no.:
23/5591.9250) for integration into the heating system and/or do-
mestic cooling water system. Observe the separate manual for
this unit here.
ū In addition to the necessary safety components, a return ow in-
crease valve which increases the return ow temperature to at
least 55 °C must always be installed (integrated into the “Olsberg
installation unit”).
ū An outlet tap must be installed in the bottom section of the wa-
ter circuit.
ū A buer must be integrated into the heating system for ecient
and fault-free operation of the LEVANA AQUA 2.0 pellet replace.
As a guideline for the storage volume, approx. 60 litres should be
provided per kW of heating output (approx. 500 litres).
ū For ecient operation of the pellet replace, it is strongly rec-
ommended that both buer sensors (top and bottom) be
connected!
Clean the heating system before hydraulic connection of the pel-
let replace through ushing in accordance with DIN EN 14336
(Heating systems in buildings – Installation and commissioning
of water based heating systems) so that the function of the pellet
replace is not endangered!
Proof of cleaning must be provided in the event of possible war-
ranty services from Olsberg.
The pellet replace may never be operated without water.
The locally applicable regulations and technical rules must also al-
ways be observed!
Venting at the vent valve
After connection of the ow and return line and lling with wa-
ter, the system should be vented at the vent valve for the pellet
replace.
Check all water connections on the pellet replace for leaks!
1
Fig. 2.37 Venting
1Vent valve
70
We reserve the right to make technical changes
78-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 7078-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 70 11.04.2023 14:41:5111.04.2023 14:41:51
70

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Olsberg ARINA 2.0 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Olsberg ARINA 2.0 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 34.97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info